All MIBs › H3C-ENTITY-EXT-MIB
Organization: Hangzhou H3C Technologies Co., Ltd.
Last Updated: 2010-12-06
Category: Hardware and Environment, Vendor: H3C/HH3C
Description: H3C MIB extending the standard entity MIB with additional physical component attributes and operational states.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is H3C-ENTITY-EXT-MIB?
H3C-ENTITY-EXT-MIB is an H3C proprietary MIB that extends the standard IETF ENTITY-MIB with additional physical component attributes and operational states specific to H3C hardware. No sample objects were provided, but the module description confirms it carries general extended information about the device, meaning additional per-component hardware detail beyond what the base standard entity MIB provides. Such extension MIBs are typically used to monitor hardware status such as component operational state or additional identification/environmental attributes not covered by the base standard, supporting device-level fault and inventory monitoring. It explicitly depends on and extends the IETF standard ENTITY-MIB (RFC 6933/4133), sharing its entPhysicalIndex-based table structure. It is deployed on H3C routers and switches that expose extended entity/component information via SNMP. Engineers can download the H3C-ENTITY-EXT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in H3C-ENTITY-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- H3C router
- H3C switch
Monitoring Examples
No sample objects were supplied for this MIB, so specific object names cannot be cited. Consistent with its stated purpose of extending entity information, a real deployment would correlate its extension table, indexed by entPhysicalIndex per standard ENTITY-MIB convention, with the base ENTITY-MIB to obtain additional component status detail, but the exact objects cannot be confirmed from the available source.
This MIB depends on
Related MIBs
Imported Objects
From ENTITY-MIB
| entPhysicalDescr | OBJECT-TYPE |
| entPhysicalName | OBJECT-TYPE |
From HUAWEI-3COM-OID-MIB
| h3cCommon | OBJECT-IDENTITY |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| MacAddress | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| h3cEntityExtend | 1.3.6.1.4.1.2011.10.2.6 | The private MIB file includes the general extent information of the device. | ||
| h3cEntityExtObjects | 1.3.6.1.4.1.2011.10.2.6.1 | |||
| h3cEntityExtState | 1.3.6.1.4.1.2011.10.2.6.1.1 | |||
| h3cEntityExtStateTable | 1.3.6.1.4.1.2011.10.2.6.1.1.1 | not-accessible | This table contains one row per physical entity, There is always at least one row for an 'overall' physical entity. The information in each row may be not include all the object in this table, because of the entity need not some of the information here. | |
| h3cEntityExtStateEntry | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1 | not-accessible | The information about a particular physical entity. | |
| I32 h3cEntityExtPhysicalIndex | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.1 | Integer32 | accessible-for-notify | The index of h3cEntityExtStateTable. This index is identical to entPhysicalIndex in ENTITY-MIB |
| H3C h3cEntityExtAdminStatus | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.2 | H3cAdminState | read-write | The administrative state for this object. |
| H3C h3cEntityExtOperStatus | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.3 | H3cOperState | read-only | The operate state for this object. |
| H3C h3cEntityExtStandbyStatus | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.4 | H3cStandbyStatus | read-only | This object is used for monitoring standby status. Not all entities support this object. |
| H3C h3cEntityExtAlarmLight | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.5 | H3cAlarmStatus | read-only | The alarm status for this entity. It does not include the severity of alarms raised on child components. In this condition, there will be a alarm light on the entity, the object should have the same status with it. |
| I32 h3cEntityExtCpuUsage | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.6 | Integer32 | read-only | The CPU usage for this entity. Generally, the CPU usage will calculate the overall CPU usage on the entity, and it is not sensible with the number of CPU on the entity. |
| I32 h3cEntityExtCpuUsageThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.7 | Integer32 | read-write | The threshold for the CPU usage. When the CPU usage exceeds the threshold, a notification will be sent. |
| I32 h3cEntityExtMemUsage | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.8 | Integer32 | read-only | The memory usage for the entity. This object indicates what percent of memory are used. |
| I32 h3cEntityExtMemUsageThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.9 | Integer32 | read-write | The threshold for the Memory usage, When the memory usage exceeds the threshold, a notification will be sent. |
| U32 h3cEntityExtMemSize | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.10 | Unsigned32 | read-only | The size of memory for the entity. |
| I32 h3cEntityExtUpTime | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.11 | Integer32 | read-only | The uptime for the entity. The meaning of uptime is when the entity is up, and the value of the object will add 1 seconds while the entity is running. |
| I32 h3cEntityExtTemperature | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.12 | Integer32 | read-only | The temperature for the entity. |
| I32 h3cEntityExtTemperatureThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.13 | Integer32 | read-write | The threshold for the temperature. When the temperature exceeds the threshold, a notification will be sent. |
| I32 h3cEntityExtVoltage | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.14 | Integer32 | read-only | The voltage for the entity. |
| I32 h3cEntityExtVoltageLowThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.15 | Integer32 | read-write | The low-threshold for the voltage. When voltage is lower than low-threshold, a notification will be sent. |
| I32 h3cEntityExtVoltageHighThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.16 | Integer32 | read-write | The high-threshold for the voltage. When voltage greater than high-threshold, a notification will be sent. |
| I32 h3cEntityExtCriticalTemperatureThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.17 | Integer32 | read-write | The threshold for the critical Temperature. When temperature exceeds the critical temperature, a notification will be sent. |
| MAC h3cEntityExtMacAddress | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.18 | MacAddress | read-only | MAC Address of the entity. |
| INT h3cEntityExtErrorStatus | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.19 | INTEGER | read-only | Indicate the error state of this entity object. Now it only supports Port, general power supply, RPS power supply and board/Subcard. It may have one of these values. The following four values can be used for all kinds of entities. notSupported(1) means this entity can not support this function. normal(2) means the statement of this entity is normal. for ports, it doesn't differentiate 10M/s, 100M/s, 1000M/s, duplex and half-duplex. For fan, power supply and board-Subcard, it means their states are normal. postFailure(3) means the entity fails to POST. entityAbsent(4) means the entity is absent now. The following values is depended on the entity . For Port entities, it may have the following values. If its POST is failure, then the value of the instance will be postFailure(3), otherwise the value will be normal(2). If enable power supply over Ethernet on this port is failure, the value of this instance will be poeError(11), otherwise it will be normal(2). For stack port, if it connects to another stack port normally, and these two units merge into one stack, then the value of this instance will be normal(2). If something wrong occurs and the unit can not merge into stack, the value of this instance will be stackPortFailed(23). If the stack port forms resilient daisy chain with another stack port on the other unit, the value of this instance will be stackPortBlocked(22). For SFP ports, if it fail to receive, the value of this instance will be sfpRecvError(31), if it fail to send, the value is sfpSendError(32), if it fail to send and receive, the value is sfpBothError(33), otherwise it will be normal(2). fanError(41) means that the fan stops working. psuError(51) means that the Power Supply Unit is in the state of fault. rpsError(61) means the RPS is in the state of fault. moduleFaulty(71) means the Module is in the state of fault. sensorError(81) means the sensor is in the state of fault. hardwareFaulty(91) means the hardware of specified entity is in the state of fault. NMS must be compatible with the states which may be added in the future. |
| I32 h3cEntityExtCpuMaxUsage | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.20 | Integer32 | read-only | The maximal CPU usage for the entity in the period of time. |
| I32 h3cEntityExtLowerTemperatureThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.21 | Integer32 | read-write | The threshold for the lower Temperature. When temperature runs under the threshold, a notification will be sent. |
| I32 h3cEntityExtShutdownTemperatureThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.22 | Integer32 | read-write | The threshold for the shutdown Temperature. When temperature exceeds the threshold, a notification will be sent and the entity will be shutdown. |
| U32 h3cEntityExtPhyMemSize | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.23 | Unsigned32 | read-only | The memory size of entity. This is the physical attribute of entity. |
| I32 h3cEntityExtPhyCpuFrequency | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.24 | Integer32 | read-only | The CPU frequency of entity. Unit of measure is MHZ. |
| DAT h3cEntityExtFirstUsedDate | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.25 | DateAndTime | read-only | The first used date of the entity. |
| I32 h3cEntityExtCpuAvgUsage | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.26 | Integer32 | read-only | The average CPU usage for the entity in a period of time. |
| I32 h3cEntityExtMemAvgUsage | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.27 | Integer32 | read-only | The average memory usage for the entity in a period of time. |
| OCT h3cEntityExtMemType | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.28 | OCTET STRING | read-only | The memory type of entity. |
| I32 h3cEntityExtCriticalLowerTemperatureThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.29 | Integer32 | read-write | The threshold for the critical Temperature. When temperature exceeds the critical lower temperature, a notification will be sent. |
| I32 h3cEntityExtShutdownLowerTemperatureThreshold | 1.3.6.1.4.1.2011.10.2.6.1.1.1.1.30 | Integer32 | read-write | The threshold for the shutdown Temperature. When temperature exceeds the lower threshold, a notification will be sent and the entity will be shutdown. |
| h3cEntityExtManu | 1.3.6.1.4.1.2011.10.2.6.1.2 | |||
| h3cEntityExtManuTable | 1.3.6.1.4.1.2011.10.2.6.1.2.1 | not-accessible | The table about device manufacture information. | |
| h3cEntityExtManuEntry | 1.3.6.1.4.1.2011.10.2.6.1.2.1.1 | not-accessible | The device manufacture information about a particular physical entity. | |
| I32 h3cEntityExtManuPhysicalIndex | 1.3.6.1.4.1.2011.10.2.6.1.2.1.1.1 | Integer32 | accessible-for-notify | The index of h3cEntityExtManuTable. This index is identical to entPhysicalIndex in ENTITY-MIB. |
| STR h3cEntityExtManuSerialNum | 1.3.6.1.4.1.2011.10.2.6.1.2.1.1.2 | SnmpAdminString | read-only | Manufacture serial number. The manufacture serial number of the entity such as chassis, module, and so on. It is got from the device when manufacturing. For low level box-device, the manufacture serial number is the device-number of System Control Board(SCB for short), it is written into the SCB directly; for middle level or high level frame-device, the manufacture serial number is the device-numbers of SCB and Service Board, because the SCB, Service Board and chassis are separate to sale and the device-number of chassis can not be written into board. |
| STR h3cEntityExtManuBuildInfo | 1.3.6.1.4.1.2011.10.2.6.1.2.1.1.3 | SnmpAdminString | read-only | Device version information. The device version information of the entity such as chassis, module, and so on. It consists of software version information and hardware version information. |
| STR h3cEntityExtManuBOM | 1.3.6.1.4.1.2011.10.2.6.1.2.1.1.4 | SnmpAdminString | read-only | Device BOM code. The device BOM code of the entity such as chassis, module, and so on. It is the component code of ERP system, which can be disassembled from device-number. |
| U32 h3cEntityExtMacAddressCount | 1.3.6.1.4.1.2011.10.2.6.1.2.1.1.5 | Unsigned32 | read-only | MAC address count. The count of MAC addresses of the entity, such as chassis, module, or port, and so on. |
| h3cEntityExtPower | 1.3.6.1.4.1.2011.10.2.6.1.3 | |||
| h3cEntityExtPowerTable | 1.3.6.1.4.1.2011.10.2.6.1.3.1 | not-accessible | This table describes the power information of all the physical entity on the device, such as the fans, the subcards, the boards, etc. | |
| h3cEntityExtPowerEntry | 1.3.6.1.4.1.2011.10.2.6.1.3.1.1 | not-accessible | The entity power information about a particular physical entity. | |
| I32 h3cEntityExtPowerPhysicalIndex | 1.3.6.1.4.1.2011.10.2.6.1.3.1.1.1 | Integer32 | accessible-for-notify | The index of h3cEntityExtPowerTable. This index is identical to entPhysicalIndex in ENTITY-MIB. |
| G32 h3cEntityExtNominalPower | 1.3.6.1.4.1.2011.10.2.6.1.3.1.1.2 | Gauge32 | read-only | The nominal power of the entity expressed in milliWatts. |
| G32 h3cEntityExtCurrentPower | 1.3.6.1.4.1.2011.10.2.6.1.3.1.1.3 | Gauge32 | read-only | The measured usage power of the entity expressed in milliWatts. |
| I32 h3cEntityExtAveragePower | 1.3.6.1.4.1.2011.10.2.6.1.3.1.1.4 | Integer32 | read-write | The average power consumed by the entity expressed in milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned. |
| I32 h3cEntityExtPeakPower | 1.3.6.1.4.1.2011.10.2.6.1.3.1.1.5 | Integer32 | read-write | The peak power consumed by the entity expressed in milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned. |
| h3cProcessObjects | 1.3.6.1.4.1.2011.10.2.6.1.4 | |||
| h3cProcessTable | 1.3.6.1.4.1.2011.10.2.6.1.4.1 | not-accessible | The Table describes the information about a particular process, namely a task. | |
| h3cProcessEntry | 1.3.6.1.4.1.2011.10.2.6.1.4.1.1 | not-accessible | The information about a particular process, namely a task. | |
| U32 h3cProcessID | 1.3.6.1.4.1.2011.10.2.6.1.4.1.1.1 | Unsigned32 | read-only | This object indicates the identifier of process, namely task ID in system. |
| STR h3cProcessName | 1.3.6.1.4.1.2011.10.2.6.1.4.1.1.2 | DisplayString | read-only | This object indicates the process name. |
| U32 h3cProcessUtil5Min | 1.3.6.1.4.1.2011.10.2.6.1.4.1.1.3 | Unsigned32 | read-only | This object provides a general idea of how busy a process caused the processor to be over a 5 minute period. The ratio is calculated by the overall CPU usage caused by the process. |
| h3cEntityExtTraps | 1.3.6.1.4.1.2011.10.2.6.2 | |||
| h3cEntityExtTrapsPrefix | 1.3.6.1.4.1.2011.10.2.6.2.0 | |||
| NTF h3cEntityExtTemperatureThresholdNotification | 1.3.6.1.4.1.2011.10.2.6.2.0.1 | The h3cEntityExtTemperatureThresholdNotification indicates the temperature exceeded the threshold. In this condition, user should check the status and the environment of the entity, sometimes it happens because of the failure of air-condition. | ||
| NTF h3cEntityExtVoltageLowThresholdNotification | 1.3.6.1.4.1.2011.10.2.6.2.0.2 | The h3cEntityExtVoltageLowThresholdNotification indicates the voltage is lower than the threshold. If the voltage is lower too much than the entity needs, the entity will halt. | ||
| NTF h3cEntityExtVoltageHighThresholdNotification | 1.3.6.1.4.1.2011.10.2.6.2.0.3 | The h3cEntityExtVoltageHighThresholdNotification indicates the voltage is higher than the threshold. If the voltage is higher too much than the entity needs, The entity may be damaged by the high voltage. | ||
| NTF h3cEntityExtCpuUsageThresholdNotfication | 1.3.6.1.4.1.2011.10.2.6.2.0.4 | The h3cEntityExtCpuUsageThresholdNotfication indicates the entity is overloaded. | ||
| NTF h3cEntityExtMemUsageThresholdNotification | 1.3.6.1.4.1.2011.10.2.6.2.0.5 | The h3cEntityExtMemUsageThresholdNotification indicates the entity is overloaded. | ||
| NTF h3cEntityExtOperEnabled | 1.3.6.1.4.1.2011.10.2.6.2.0.6 | The trap indicates the entity is operable at present. | ||
| NTF h3cEntityExtOperDisabled | 1.3.6.1.4.1.2011.10.2.6.2.0.7 | The trap indicates the entity is not operable at present. | ||
| NTF h3cEntityExtCriticalTemperatureThresholdNotification | 1.3.6.1.4.1.2011.10.2.6.2.0.8 | The h3cEntityExtCriticalTemperatureThresholdNotification indicates the temperature exceeds the critical temperature. In this condition, user should check the status and the environment of the entity, sometimes it happens because of the failure of air-condition. | ||
| NTF h3cEntityExtSFPAlarmOn | 1.3.6.1.4.1.2011.10.2.6.2.0.9 | The trap is generated when the SFP module fails or runs abnormally for some particular reason. | ||
| NTF h3cEntityExtSFPAlarmOff | 1.3.6.1.4.1.2011.10.2.6.2.0.10 | The trap is generated when the SFP module restores to normal status. | ||
| NTF h3cEntityExtSFPPhony | 1.3.6.1.4.1.2011.10.2.6.2.0.11 | This module is NOT sold by authorized manufacturer. The normal function of the device or assume the maintenance responsibility thereof will NOT be guaranteed. The trap is generated periodically after a phony module has been found. | ||
| NTF h3cEntityInsert | 1.3.6.1.4.1.2011.10.2.6.2.0.12 | The trap is generated when a removeable entity inserting to device. | ||
| NTF h3cEntityRemove | 1.3.6.1.4.1.2011.10.2.6.2.0.13 | The trap is generated when a removeable entity removing from device. | ||
| NTF h3cEntityExtForcedPowerOff | 1.3.6.1.4.1.2011.10.2.6.2.0.14 | The trap indicates the entity is forced to power off. | ||
| NTF h3cEntityExtForcedPowerOn | 1.3.6.1.4.1.2011.10.2.6.2.0.15 | The trap indicates the entity is forced to power on. | ||
| NTF h3cEntityExtFaultAlarmOn | 1.3.6.1.4.1.2011.10.2.6.2.0.16 | The trap indicates a fault occures on the specified entity. | ||
| NTF h3cEntityExtFaultAlarmOff | 1.3.6.1.4.1.2011.10.2.6.2.0.17 | The trap indicates a fault disappears on the specified entity. | ||
| NTF h3cEntityExtResourceLack | 1.3.6.1.4.1.2011.10.2.6.2.0.18 | The trap indicates that a kind of resource is not enough on the specified entity. | ||
| NTF h3cEntityExtResourceEnough | 1.3.6.1.4.1.2011.10.2.6.2.0.19 | The trap indicates that the entity recovers from the status of no enough resource. | ||
| NTF h3cEntityExtTemperatureLower | 1.3.6.1.4.1.2011.10.2.6.2.0.20 | The trap indicates the temperature of a specified entity is under the lower threshold. In this condition, user should check the status and the environment of the entity, sometimes it goes wrong for some reason. | ||
| NTF h3cEntityExtTemperatureTooUp | 1.3.6.1.4.1.2011.10.2.6.2.0.21 | The trap indicates the temperature of a specified entity exceeded the shutdown threshold. In this condition, user should check the status and the environment of the entity, sometimes it goes wrong for some reason. | ||
| NTF h3cEntityExtTemperatureNormal | 1.3.6.1.4.1.2011.10.2.6.2.0.22 | The trap indicates the temperature of a specified entity recover from abnormal status. | ||
| NTF h3cEntityExternalAlarmOccur | 1.3.6.1.4.1.2011.10.2.6.2.0.23 | The trap is generated when the monitored device connected to the specified entity fails. | ||
| NTF h3cEntityExternalAlarmRecover | 1.3.6.1.4.1.2011.10.2.6.2.0.24 | The trap is generated when the failed device connected to the specified entity returns to normal. | ||
| NTF h3cEntityExtCpuUsageThresholdRecover | 1.3.6.1.4.1.2011.10.2.6.2.0.25 | The trap indicates the CPU usage descends the threshold. | ||
| NTF h3cEntityExtMemUsageThresholdRecover | 1.3.6.1.4.1.2011.10.2.6.2.0.26 | The trap indicates the memory usage descends the threshold. | ||
| NTF h3cEntityExtMemAllocatedFailed | 1.3.6.1.4.1.2011.10.2.6.2.0.27 | The trap indicates the memory allocated failed. | ||
| NTF h3cEntityExtECCParityAlarm | 1.3.6.1.4.1.2011.10.2.6.2.0.28 | The trap indicates the ECC(Error Correction Code) parity error alarm. | ||
| NTF h3cEntityExtCritLowerTempThresholdNotification | 1.3.6.1.4.1.2011.10.2.6.2.0.29 | The h3cEntityExtCritLowerTempThresholdNotification indicates the temperature is lower than the threshold. If the temperature is lower too much than the entity needs, the entity will halt. | ||
| NTF h3cEntityExtTemperatureTooLow | 1.3.6.1.4.1.2011.10.2.6.2.0.30 | The h3cEntityExtTemperatureTooLow indicates the temperature is lower than the threshold. If the temperature is lower too much than the entity needs, the entity halts now. | ||
| NTF h3cEntityExtFanDirectionNotPreferred | 1.3.6.1.4.1.2011.10.2.6.2.0.31 | This trap indicates the specified fan's direction does not accord with preferred. The two parameters indicate the entity index and physical name of fan. | ||
| NTF h3cEntityExtFanDirectionNotAccord | 1.3.6.1.4.1.2011.10.2.6.2.0.32 | This trap indicates the direction of fans does not accord with each other. The two parameters indicate the parent entity of the fans. | ||
| NTF h3cEntityExtSFPInvalid | 1.3.6.1.4.1.2011.10.2.6.2.0.33 | The transceiver module is not compatible with the interface card. The authorized manufacturer therefore shall NOT guarantee the normal function of the transceiver. The transceiver module will be invalidated in days. Please replace it with a compatible one as soon as possible. The trap is generated periodically after a phony transceiver module has been found. | ||
| NTF h3cEntityExtSFPInvalidNow | 1.3.6.1.4.1.2011.10.2.6.2.0.34 | This transceiver module is not compatible with the interface card. The authorized manufacturer therefore shall NOT guarantee the normal function of the transceiver. The trap is generated after a phony transceiver module has been found. | ||
| h3cEntityExtTrapsInfor | 1.3.6.1.4.1.2011.10.2.6.2.1 | |||
| STR h3cEntityExtTrapDescription | 1.3.6.1.4.1.2011.10.2.6.2.1.1 | SnmpAdminString | accessible-for-notify | The information of trap. |
| INT h3cEntityExtECCParityAlarmStatus | 1.3.6.1.4.1.2011.10.2.6.2.1.2 | INTEGER | accessible-for-notify | ECC parity error. |
| I32 h3cEntityExtSFPInvalidInDays | 1.3.6.1.4.1.2011.10.2.6.2.1.3 | Integer32 | accessible-for-notify | The days when the transceiver module is still valid, but after those days, it will be invaldated. |
| h3cEntityExtConformance | 1.3.6.1.4.1.2011.10.2.6.3 | |||
| h3cEntityExtCompliances | 1.3.6.1.4.1.2011.10.2.6.3.1 | |||
| h3cEntityExtCompliance | 1.3.6.1.4.1.2011.10.2.6.3.1.1 | The compliance statement for systems supporting this MIB. | ||
| h3cEntityExtGroups | 1.3.6.1.4.1.2011.10.2.6.3.2 | |||
| h3cEntityExtGroup | 1.3.6.1.4.1.2011.10.2.6.3.2.1 | Entity Extend group. | ||
| h3cEntityExtNotificationGroup | 1.3.6.1.4.1.2011.10.2.6.3.2.2 | Entity Extend Notification group. | ||
| h3cEntityExtManuGroup | 1.3.6.1.4.1.2011.10.2.6.3.2.3 | Standard Device Manufacture Information group. | ||
| h3cEntityExtPowerGroup | 1.3.6.1.4.1.2011.10.2.6.3.2.4 | Standard Entity Power Information group. |
RFC description
H3C entity extended properties MIB for hardware status, temperature, and power monitoring.
Start monitoring H3C router/switch (extended physical-entity attributes) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.