Fibronics-EtherSwitch-MIB

All MIBs › Fibronics-EtherSwitch-MIB

Category: Technology: Switching/L2, Vendor: Fibronics (Legacy)

Description: Fibronics proprietary Ethernet switch MIB for managing Fibronics EtherSwitch LAN switching equipment and port configurations.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Fibronics-EtherSwitch-MIB?

Fibronics-EtherSwitch-MIB is a legacy proprietary MIB for Fibronics EtherSwitch Ethernet switching equipment, covering device identity, network configuration, and trap receiver management. It exposes firmware and hardware version identifiers, the switch's IP addressing (address, netmask, default gateway), and a table of configured trap receivers with their status and sequencing. Its monitoring value centers on device/software identity and configuration state, specifically confirming firmware/hardware version for inventory and compliance purposes and verifying that trap notifications are correctly routed to the intended management stations. It does not show explicit dependency on other MIBs in the provided objects, appearing as a self-contained enterprise switch MIB from an era before common Bridge/IF-MIB adoption was universal. It would have been deployed on Fibronics-branded Ethernet LAN switches in enterprise wiring closets, primarily in legacy or older network installations, where Fibronics-EtherSwitch-MIB SNMP monitoring verified firmware/hardware version and trap receiver configuration.

IPNetwork Monitor allows you to monitor SNMP objects defined in Fibronics-EtherSwitch-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Fibronics EtherSwitch LAN switch

Monitoring Examples

An admin would check fibEsFwVer and fibEsHwVer to confirm the switch's firmware/hardware revision during an inventory audit, and review fibEsIpAddr, fibEsNetMask, and fibEsDefaultGateway to validate management network configuration. The fibEsTrapRcvrTable (via fibEsTrapRcvrEntry, fibEsTrapRcvrIndex, fibEsTrapRcvrStatus) would be polled to ensure the configured trap receiver count (fibEsTrapRcvrCurEnt) matches expectations and that entries are in an active status, revealing a misconfigured or disabled trap destination if not.

What Can Be Monitored

firmware version
hardware version
IP address/netmask/gateway configuration
trap receiver table entries and status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
fibronics	1.3.6.1.4.1.22
products	1.3.6.1.4.1.22.100
eth_switch	1.3.6.1.4.1.22.100.9
xm516_card	1.3.6.1.4.1.22.100.9.3
xm517_card	1.3.6.1.4.1.22.100.9.4
xm518_card	1.3.6.1.4.1.22.100.9.5
xm519_card	1.3.6.1.4.1.22.100.9.6
xm5110_card	1.3.6.1.4.1.22.100.9.7
xm5111_card	1.3.6.1.4.1.22.100.9.8
xm5112_card	1.3.6.1.4.1.22.100.9.9
xm5113_card	1.3.6.1.4.1.22.100.9.10
xm5114_card	1.3.6.1.4.1.22.100.9.11
xm5115_card	1.3.6.1.4.1.22.100.9.12
mibs	1.3.6.1.4.1.22.101
mibsbridges	1.3.6.1.4.1.22.101.9
mibbridges_specific	1.3.6.1.4.1.22.101.9.1
mibeth2eth	1.3.6.1.4.1.22.101.9.1.2
mib_eps	1.3.6.1.4.1.22.101.9.1.2.1
fibEsObjects	1.3.6.1.4.1.22.101.9.1.2.1.1
fibEsMain	1.3.6.1.4.1.22.101.9.1.2.1.1.1
fibEsConfig	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1
STR fibEsFwVer	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.1	DisplayString	read-only	The firmware version in the form major.minor.
STR fibEsHwVer	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.2	DisplayString	read-only	The hardware version in the form major.minor.
IP fibEsIpAddr	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.3	IpAddress	read-write	The administrative value of the IP address. The current operational IP address can be obtained by the ipAdEntAddr entry in the ipAddrTable. This parameter will take effect only after a reset (fibEsReset) is issued or a power cycle.
IP fibEsNetMask	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.4	IpAddress	read-write	The administrative value of the subnet mask. The current operational subnet mask can be obtained by the ipAdEntNetMask entry in the ipAddrTable. This parameter will take effect only after a reset (fibEsReset) is issued or a power cycle.
IP fibEsDefaultGateway	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.5	IpAddress	read-write	The administrative value of the default gateway (router) IP address. The current operational default gateway's IP address can be obtained from the ipRouteTable. This parameter will take effect only after a reset (fibEsReset) is issued or a power cycle.
INT fibEsTrapRcvrMaxEnt	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.6	INTEGER	read-only	The maximum number of rows in the trap receiver table.
INT fibEsTrapRcvrCurEnt	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.7	INTEGER	read-only	The current number of rows in the trap receiver table.
INT fibEsTrapRcvrNext	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.8	INTEGER	read-only	The index of the next available row to be created in the trap receiver table. A value of zero means that the table is full and no more rows can be added.
fibEsTrapRcvrTable	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9		not-accessible	A table of managers to which to send traps. Entries in the table are saved across resets and power cycles.
fibEsTrapRcvrEntry	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1		not-accessible	Definition of rows in the trap receiver table. The column fibEsTrapRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with objects fibEsTrapRcvrStatus, fibEsTrapRcvrIpAddress, and fibEsTrapRcvrComm.
INT fibEsTrapRcvrIndex	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.1	INTEGER	read-only	The index of the row in the table.
INT fibEsTrapRcvrStatus	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.2	INTEGER	read-write	Setting this object to the value invalid(3) deletes the row from the table. The value invalid(3) should never be returned on a GET. The value of create(4) on a SET causes a new row to be created if the row does not already exist. If it does, then a 'badValue'error should be returned. The value returned on GETs should be valid(2) or other(1), which is used to indicate any other condition.
IP fibEsTrapRcvrIpAddress	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.3	IpAddress	read-write	IP address for an SNMP manager that is to receive the trap.
STR fibEsTrapRcvrComm	1.3.6.1.4.1.22.101.9.1.2.1.1.1.1.9.1.4	DisplayString	read-write	Community string to use.
fibEsSys	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2
INT fibEsNumPorts	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.1	INTEGER	read-only	The maximum number of ports on the switch.
INT fibEsNumStations	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.2	INTEGER	read-only	Aggregate number of currently active stations (nodes) on all ports on the switch. This is the value from the system module.
INT fibEsMostStations	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.3	INTEGER	read-only	Highest aggregate number of stations ever active on all ports at one time, since the last reset or power cycle. This is the value as seen by the system module.
INT fibEsMaxStations	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.4	INTEGER	read-only	Highest aggregate number of stations which the switch can support simultaneously. (This is the maximum number that the system module can support.)
INT fibEsReset	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.5	INTEGER	read-write	This object is used to reset the switch. Writing softReset(3) causes the switch to reset the hardware, run quick diagnostics, clear all counters, start switching, issue a warmstart trap, and then be able to respond to SNMP requests. Writing hardReset(4) causes the switch to run power up diagnostics and then execute a soft reset. Note: all address tables are cleared in both cases. The administrative parameters from nonvolatile memory are used to initialize the operational parameters. The value returned on GETs should be running(2) or other(1), which is used to indicate any other condition.
CTR fibEsNumResets	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.6	Counter	read-only	Number of soft resets the switch has executed since the last hard reset or power cycle. Soft resets are defined as writing softReset(3) to fibEsReset, pressing the front panel reset button, executing a soft reset from the console, or resets induced by the switch firmware.
INT fibEsAddrAgingTime	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.7	INTEGER	read-write	Number of minutes of inactivity before an address entity is aged out. A value of zero means no aging. Note: if an address shows up on another port, the original port to address assignment is automatically deleted. The value is saved across resets and power cycles.
fibEsSysStaTable	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9		not-accessible	A table of station addresses from all ports known to the system module.
fibEsSysStaEntry	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1		not-accessible	Definition of the rows in the system module station address table. Rows can not be created or deleted via SNMP requests.
MAC fibEsSysStaMacAddr	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1.1	MacAddr	read-only	The Station's MAC address.
INT fibEsSysStaPort	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1.2	INTEGER	read-only	The source port for the Station.
OCT fibEsSysStaTraffic	1.3.6.1.4.1.22.101.9.1.2.1.1.1.2.9.1.3	OCTET STRING	read-only	A bit string that identifies with value of one of the ports that this station has generated traffic to or from. The bits are numbered starting at zero, with bit zero being the high order bit in the first byte, bit seven being the low order bit in the first byte, bit eight being the high order bit in the second byte, etc. Ports correspond with bits (i.e., port 1 is bit 1, etc.). The size of this in octets is the number of ports (i.e., fibEsNumPorts), divided by 8, plus one.
fibEsPort	1.3.6.1.4.1.22.101.9.1.2.1.1.2
fibEsPortTable	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1		not-accessible	A table of information about each port. The number of rows is given by fibEsNumPorts.
fibEsPortEntry	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1		not-accessible	Definition of rows in the port table. The number of rows is determined by the hardware and is specified by the value of fibEsNumPorts. Rows can not be created or deleted via SNMP requests.
INT fibEsPortIndex	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.1	INTEGER	read-only	A unique value for each port entry. The value corresponds the port number.
INT fibEsPortOprStatus	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.2	INTEGER	read-write	The operational status of the port. Setting to enabled(1) enables the port. Setting to disabled(2) disables the port. The value is saved across resets and power cycles.
INT fibEsPortDuplex	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.3	INTEGER	read-only	Indicates whether the port is jumper configured for full or half duplex operation. Note: internal connected ports are always halfDuplex(2).
CTR fibEsPortRcvLocalFrames	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.4	Counter	read-only	Number of frames received where the destination is on this port.
CTR fibEsPortForwardedFrames	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.5	Counter	read-only	Number of frames received on this port and forwarded to another port or the system module for processing.
CTR fibEsPortMostStations	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.6	Counter	read-only	Highest number of stations ever active at any time since the last reset of the switch as seen by this port.
CTR fibEsPortMaxStations	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.7	Counter	read-only	Maximum number of stations which the port can support simultaneously.
CTR fibEsPortSWHandledFrames	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.8	Counter	read-only	Number of Frames received on this port and delivered to the system module for processing.
CTR fibEsPortLocalStations	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.9	Counter	read-only	Number of stations on this port's address table which belong to the segment attached to this port.
CTR fibEsPortRemoteStations	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.10	Counter	read-only	Number of stations on this port's address table which belong to segments attached to other ports.
CTR fibEsPortUnknownStaFrames	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.11	Counter	read-only	Number of unicast frames received on this port and forwarded to the system module for processing because the source or destination station address is not in the port's forwarding table.
INT fibEsPortResetStats	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.12	INTEGER	read-write	Setting this object to reset(3) causes all traffic counters for this port to be set to zero. Also the value of fibEsPortResetTimer is set to zero.
TIK fibEsPortResetTimer	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.13	TimeTicks	read-only	Time (in 100th second ticks) since the port counters were reset.
INT fibEsPortResetAddrs	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.14	INTEGER	read-write	Setting this object to reset(3) clears all address table entries for this port as well as setting all port traffic counters to zero and setting fibEsPortResetTimer to zero.
CTR fibEsPortRcvBcasts	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.15	Counter	read-only	Number of Broadcast Frames received on this port without errors.
CTR fibEsPortSwitchedFrames	1.3.6.1.4.1.22.101.9.1.2.1.1.2.1.1.16	Counter	read-only	Number of frames switched on this port

RFC description

Manages Fibronics EtherSwitch bridge products including XM516-XM5115 card models for Ethernet switching and port configuration.

Start monitoring Fibronics EtherSwitch LAN switch (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Fibronics-EtherSwitch-MIB

What Is Fibronics-EtherSwitch-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description