All MIBs › Dell-TIMESYNCHRONIZATION-MIB
Organization: Dell
Last Updated: 2009--0-6-
Category: Protocol: NTP, Vendor: Dell
Description: Manages NTP/SNTP time synchronization configuration and status on Dell network switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Dell-TIMESYNCHRONIZATION-MIB?
Dell-TIMESYNCHRONIZATION-MIB is a Dell private MIB for configuring and monitoring NTP/SNTP time synchronization, time zone, and daylight saving time settings on Dell network switches. It exposes the switch's currently managed time and date, the active synchronization method (NTP or SNTP client), time zone and DST configuration, and DST start/end schedule with offset. Its monitoring focus is software/system configuration correctness: confirming rndTimeSyncManagedTime/rndTimeSyncManagedDateTime reflects accurate, synchronized time (critical for correlating logs and traps across a fleet), and verifying rlTimeSyncMethod and rlSntpNtpClient/rlSntpNtpConfig show the device is actually configured to sync against a time source rather than free-running. This MIB depends on the underlying NTP/SNTP protocol standards for its actual time-sync mechanism. It is deployed on Dell switches across an enterprise network where consistent, accurate device clocks are required for log correlation, certificate validation, and scheduled operations. Engineers can download the Dell-TIMESYNCHRONIZATION-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Dell-TIMESYNCHRONIZATION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Dell network switch
Monitoring Examples
An admin would read rndTimeSyncManagedTime/rndTimeSyncManagedDate/rndTimeSyncManagedDateTime to confirm the switch's current system clock, and check rlTimeSyncMethod and rlTimeSyncMethodMode to see whether NTP or SNTP is active. rlTimeZone, rlDaylightSavingTimeMode, rlDaylightSavingTimeStart/End, and rlDaylightSavingTimeOffset reveal whether DST transitions are correctly configured for the local region. A switch whose managed time drifts significantly from other devices, or whose rlSntpNtpClient/rlSntpNtpConfig shows no configured server, would indicate a time-sync failure that could break certificate validation or make cross-device log correlation unreliable.
What Can Be Monitored
- current system time/date
- active time-sync method (NTP/SNTP)
- NTP/SNTP client configuration
- time zone and DST configuration/schedule
This MIB depends on
Related MIBs
Imported Objects
From Dell-MIB
| rnd | MODULE-IDENTITY |
From IF-MIB
| InterfaceIndex |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| rlTimeSynchronization | 1.3.6.1.4.1.89.92 | The MIB module describes the private MIB for SNTP & TIME definitions. | ||
| rlTimeSyncMethodMode | 1.3.6.1.4.1.89.92.1 | |||
| INT rlTimeSyncMibVersion | 1.3.6.1.4.1.89.92.1.1 | INTEGER | read-only | TimeSync Mib Version. |
| STR rndTimeSyncManagedTime | 1.3.6.1.4.1.89.92.1.2 | DisplayString | read-write | The time will be sent in the format hhmmss |
| STR rndTimeSyncManagedDate | 1.3.6.1.4.1.89.92.1.3 | DisplayString | read-write | The date will be sent in the format ddmmyy |
| STR rndTimeSyncManagedDateTime | 1.3.6.1.4.1.89.92.1.4 | DisplayString | read-write | The date and time will be sent in the format ddmmyyhhmmss |
| RLT rlTimeSyncMethod | 1.3.6.1.4.1.89.92.1.5 | RlTimeSyncMethod | read-write | Method to be used for time synchronization in the device. |
| STR rlTimeZone | 1.3.6.1.4.1.89.92.1.6 | DisplayString | read-write | Offset from Greenwich time (format [+/-]hh:mm). |
| STR rlTimeZoneCode | 1.3.6.1.4.1.89.92.1.7 | DisplayString | read-write | Code definition for current TimeZone. |
| RLD rlDaylightSavingTimeMode | 1.3.6.1.4.1.89.92.1.8 | RlDaylightSavingTimeMode | read-write | Daylight Saving Time - Recurring/Date/None. |
| OCT rlDaylightSavingTimeStart | 1.3.6.1.4.1.89.92.1.9 | OCTET STRING | read-write | Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1). |
| OCT rlDaylightSavingTimeEnd | 1.3.6.1.4.1.89.92.1.10 | OCTET STRING | read-write | Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1). |
| I32 rlDaylightSavingTimeOffset | 1.3.6.1.4.1.89.92.1.11 | Integer32 | read-write | Daylight Saving Time - The number of minutes to add to the clock during summer time. |
| STR rlDaylightSavingTimeCode | 1.3.6.1.4.1.89.92.1.12 | DisplayString | read-write | Code definition for current Daylight Saving Time. |
| INT rlTZDSTOffset | 1.3.6.1.4.1.89.92.1.13 | INTEGER | read-only | Local Time Zone and Daylight Saving Time offset in seconds. |
| STR rlTimeZoneName | 1.3.6.1.4.1.89.92.1.14 | DisplayString | read-write | Human readable string describing Local Time Zone and Daylight Saving Time. |
| rlTimeZoneTable | 1.3.6.1.4.1.89.92.1.15 | not-accessible | TimeZone information. | |
| rlTimeZoneEntry | 1.3.6.1.4.1.89.92.1.15.1 | not-accessible | The row definition for this table. | |
| INT rlTimeZoneIndex | 1.3.6.1.4.1.89.92.1.15.1.1 | INTEGER | not-accessible | Entry index. A row with index 2 will be existing in case the DHCP timezone is supported, and will contain Timezone and Summertime dynamic values. Using index 2 in SET operations is allowed only for SNMP inner clients (SNMPServ users), on condition that DHCP timezone option is supported. |
| RLT rlTimeZoneTimeSyncMethod | 1.3.6.1.4.1.89.92.1.15.1.2 | RlTimeSyncMethod | read-write | Method to be used for time synchronization in the device. |
| STR rlTimeZoneTimeZoneOffset | 1.3.6.1.4.1.89.92.1.15.1.3 | DisplayString | read-write | Offset from Greenwich time (format [+/-]hh:mm). |
| STR rlTimeZoneTimeZoneCode | 1.3.6.1.4.1.89.92.1.15.1.4 | DisplayString | read-write | Code definition for current TimeZone. |
| RLD rlTimeZoneDaylightSavingTimeMode | 1.3.6.1.4.1.89.92.1.15.1.5 | RlDaylightSavingTimeMode | read-write | Daylight Saving Time - Recurring/Date/None. |
| OCT rlTimeZoneDaylightSavingTimeStart | 1.3.6.1.4.1.89.92.1.15.1.6 | OCTET STRING | read-write | Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1). |
| OCT rlTimeZoneDaylightSavingTimeEnd | 1.3.6.1.4.1.89.92.1.15.1.7 | OCTET STRING | read-write | Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1). |
| I32 rlTimeZoneDaylightSavingTimeOffset | 1.3.6.1.4.1.89.92.1.15.1.8 | Integer32 | read-write | Daylight Saving Time - The number of minutes to add to the clock during summer time. |
| STR rlTimeZoneDaylightSavingTimeCode | 1.3.6.1.4.1.89.92.1.15.1.9 | DisplayString | read-write | Code definition for current Daylight Saving Time. |
| INT rlTimeZoneTZDSTOffset | 1.3.6.1.4.1.89.92.1.15.1.10 | INTEGER | read-only | Local Time Zone and Daylight Saving Time offset in seconds. |
| STR rlTimeZoneTimeZoneName | 1.3.6.1.4.1.89.92.1.15.1.11 | DisplayString | read-write | Human readable string describing Local Time Zone and Daylight Saving Time. |
| INT rlTimeZoneDataType | 1.3.6.1.4.1.89.92.1.15.1.12 | INTEGER | read-only | The type of data in this entry: static or dynamic. |
| INT rlTimeZoneDataSourceIfIndex | 1.3.6.1.4.1.89.92.1.15.1.13 | INTEGER | read-write | IfIndex of the interface through which the dynamic data of this row has been learned. The value of this field will be 0 if rlTimeZoneTimeDataType is static (since it is relevant only for dynamic entry), and this is the only value allowed for SET in this case. |
| INT rlTimeZoneDataDynamicConfSource | 1.3.6.1.4.1.89.92.1.15.1.14 | INTEGER | read-write | The source of dynamic data in this entry, for example: dhcpv4. Values other than 'none' are relevant only for dynamic entry. |
| INT rlClockStatus | 1.3.6.1.4.1.89.92.1.16 | INTEGER | read-only | Current status of the clock. The value 'invalid' means time is meaninglesss, since it has neither been manually configured nor achieved as a result of SNTP synchronization. |
| T/F rlDhcpTimezoneOptionEnabled | 1.3.6.1.4.1.89.92.1.17 | TruthValue | read-write | Specifies whether the DHCP Timezone option (DHCPv4 option 100) is supported in the system. Setting this value to FALSE, will clear Timezone and Summertime dynamic configuration, so that: 1) rlTimeZoneTimeZoneCode and rlTimeZoneDaylightSavingTimeCode length will be 0 for rlTimeZoneEntry whose index = 2 (dynamic entry). 2) the operative values of Timezone and Summertime will be those statically configured. Thus, GET operations on the following MIB scalars will result is static values: rlTimeZone, rlTimeZoneCode, rlDaylightSavingTimeMode, rlDaylightSavingTimeStart, rlDaylightSavingTimeEnd, rlDaylightSavingTimeOffset, rlDaylightSavingTimeCode, rlTZDSTOffset. |
| T/F rlAutomaticClockSetFromPCEnabled | 1.3.6.1.4.1.89.92.1.18 | TruthValue | read-write | Specifies whether automatic set of time and date is permitted from connected host PC. The feature is meant to be used in order to initialize the clock after reboot (if SNTP is not in use), since the device does not have a realtime clock. |
| T/F rlTimeAndDateHaveBeenSet | 1.3.6.1.4.1.89.92.1.19 | TruthValue | read-only | Indicates whether the time and date have been set in the device, manually or through SNTP synchronization. If only time has been set, the value of this MIB will be FALSE. If only date has been set, the value of this MIB will be FALSE. |
| rlSntpNtpClient | 1.3.6.1.4.1.89.92.2 | |||
| rlSntpNtpConfig | 1.3.6.1.4.1.89.92.2.1 | |||
| INT rlSntpNtpMibVersion | 1.3.6.1.4.1.89.92.2.1.1 | INTEGER | read-only | SntpNtp Mib Version. |
| INT rlSntpNtpConfigMode | 1.3.6.1.4.1.89.92.2.1.2 | INTEGER | read-only | Current configuration operational mode of SNTP/NTP client. |
| NTP rlSntpNtpConfigSysStratum | 1.3.6.1.4.1.89.92.2.1.3 | NTPStratum | read-only | The stratum of the local clock. If the value is set to 1, i.e., this is a primary reference, then the Primary-Clock procedure described in Section 3.4.6, in RFC-1305 is invoked. |
| INT rlSntpNtpConfigPollInterval | 1.3.6.1.4.1.89.92.2.1.4 | INTEGER | read-write | Period of time (in seconds) between succesive attempts to perform an update via SNTP. |
| IP rlSntpNtpConfigPrimaryPollSrvAddr | 1.3.6.1.4.1.89.92.2.1.5 | IpAddress | read-only | Ip Address of a trusted SNTP server for polling. |
| INT rlSntpNtpConfigPrimaryPollSrvMrid | 1.3.6.1.4.1.89.92.2.1.6 | INTEGER | read-only | The mrid of the primary server. |
| INT rlSntpNtpConfigPrimaryPollSrvIfIndex | 1.3.6.1.4.1.89.92.2.1.7 | INTEGER | read-only | The interface addressed of the primary server. |
| NTP rlSntpNtpConfigPrimaryPollSrvStratum | 1.3.6.1.4.1.89.92.2.1.8 | NTPStratum | read-only | The stratum of the primary polling server. |
| IP rlSntpNtpConfigSyncSrvAddr | 1.3.6.1.4.1.89.92.2.1.9 | IpAddress | read-only | Ip Address of the synced server. |
| INT rlSntpNtpConfigSyncSrvMrid | 1.3.6.1.4.1.89.92.2.1.10 | INTEGER | read-only | The mrid of the synced server. |
| INT rlSntpNtpConfigSyncSrvIfIndex | 1.3.6.1.4.1.89.92.2.1.11 | INTEGER | read-only | The interface addressed of the synced server. |
| RLS rlSntpNtpConfigSyncSrvType | 1.3.6.1.4.1.89.92.2.1.12 | RlSntpNtpSyncType | read-only | Synced server type. |
| NTP rlSntpNtpConfigSyncSrvStratum | 1.3.6.1.4.1.89.92.2.1.13 | NTPStratum | read-only | The stratum of the synced server. |
| I32 rlSntpNtpConfigRetryTimeout | 1.3.6.1.4.1.89.92.2.1.14 | Integer32 | read-only | SNTP/NTP requests Retry Interval. |
| I32 rlSntpNtpConfigRetryCnt | 1.3.6.1.4.1.89.92.2.1.15 | Integer32 | read-only | SNTP/NTP requests Retry Count. |
| rlSntpNtpConfigSrvTable | 1.3.6.1.4.1.89.92.2.1.16 | not-accessible | A table containing information about config servers. | |
| rlSntpNtpConfigSrvEntry | 1.3.6.1.4.1.89.92.2.1.16.1 | not-accessible | Entry in rlSntpNtpConfigSrvTable. | |
| RLS rlSntpNtpConfigSrvEntryType | 1.3.6.1.4.1.89.92.2.1.16.1.1 | RlSntpNtpSyncEntryType | not-accessible | Server type: Synchronize Server or Primary Poll Server. |
| IPt rlSntpNtpConfigSrvInetAddressType | 1.3.6.1.4.1.89.92.2.1.16.1.2 | InetAddressType | read-only | Server inet address type. |
| IP rlSntpNtpConfigSrvInetAddress | 1.3.6.1.4.1.89.92.2.1.16.1.3 | InetAddress | read-only | Server inet address. |
| INT rlSntpNtpConfigSrvMrid | 1.3.6.1.4.1.89.92.2.1.16.1.4 | INTEGER | read-only | The mrid of the server. |
| INT rlSntpNtpConfigSrvIfIndex | 1.3.6.1.4.1.89.92.2.1.16.1.5 | INTEGER | read-only | The interface addressed of the server. |
| RLS rlSntpNtpConfigSrvSyncType | 1.3.6.1.4.1.89.92.2.1.16.1.6 | RlSntpNtpSyncType | read-only | The type of synchronization. |
| NTP rlSntpNtpConfigSrvStratum | 1.3.6.1.4.1.89.92.2.1.16.1.7 | NTPStratum | read-only | The stratum of the synced server. |
| rlSntpConfig | 1.3.6.1.4.1.89.92.2.2 | |||
| INT rlSntpClientMode | 1.3.6.1.4.1.89.92.2.2.1 | INTEGER | read-only | Current operational mode of SNTP client. |
| INT rlSntpUnicastAdminState | 1.3.6.1.4.1.89.92.2.2.2 | INTEGER | read-write | SNTP Unicast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled. |
| INT rlSntpBroadcastAdminState | 1.3.6.1.4.1.89.92.2.2.3 | INTEGER | read-write | SNTP Broadcast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled. |
| INT rlSntpAnycastAdminState | 1.3.6.1.4.1.89.92.2.2.4 | INTEGER | read-write | SNTP Anycast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled. |
| T/F rlSntpUnicastPollState | 1.3.6.1.4.1.89.92.2.2.5 | TruthValue | read-write | SNTP Unicast poll state - TRUE for polled. |
| T/F rlSntpBroadcastPollState | 1.3.6.1.4.1.89.92.2.2.6 | TruthValue | read-write | SNTP Broadcast poll state - TRUE for polled. |
| T/F rlSntpAnycastPollState | 1.3.6.1.4.1.89.92.2.2.7 | TruthValue | read-write | SNTP Anycast poll state - TRUE for polled. |
| INT rlSntpAuthenticationState | 1.3.6.1.4.1.89.92.2.2.8 | INTEGER | read-write | SNTP authentication state- Enable/Disable SNTP. |
| T/F rlTimeValidFlag | 1.3.6.1.4.1.89.92.2.2.9 | TruthValue | read-write | Is time valid. |
| rlSntpConfigBroadcastTable | 1.3.6.1.4.1.89.92.2.2.10 | not-accessible | A table containing broadcast mode information per interface. | |
| rlSntpBroadcastEntry | 1.3.6.1.4.1.89.92.2.2.10.1 | not-accessible | Private paramters for interface: sntp status, broadcast mode. | |
| INT rlSntpBroadcastIfIndex | 1.3.6.1.4.1.89.92.2.2.10.1.1 | INTEGER | not-accessible | The interface addressed by this entry. |
| INT rlSntpBroadcastIfAdminState | 1.3.6.1.4.1.89.92.2.2.10.1.2 | INTEGER | read-write | SNTP interface Adminstrative state- Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled. |
| INT rlSntpBroadcastMode | 1.3.6.1.4.1.89.92.2.2.10.1.3 | INTEGER | read-write | SNTP/NTP Broadcast Mode. none - no broadcast SNTP packets are received or sent. Receive - host only receive SNTP packets that were sent to broadcast address (were not directed to the host). This is multicast mode in the RFC. Send - host only send SNTP packets and wait for replies directed to the host. This is anycast mode in the RFC. ReceiveSend - host receive broadcast messages (destination is broadcast address in the received messages) and send SNTP packets to wait for replies directed to the host (destination address of the reply is the host address). This mode combines anycast and multicast modes in the RFC. |
| T/F rlSntpBroadcastPolled | 1.3.6.1.4.1.89.92.2.2.10.1.4 | TruthValue | read-write | TRUE if participating in polling cycle, else FALSE. |
| IP rlSntpBroadcastAddress | 1.3.6.1.4.1.89.92.2.2.10.1.5 | IpAddress | read-only | Ip Address of a trusted SNTP server. |
| NTP rlSntpBroadcastStratum | 1.3.6.1.4.1.89.92.2.2.10.1.6 | NTPStratum | read-only | The stratum of this server. |
| NTP rlSntpBroadcastLastResp | 1.3.6.1.4.1.89.92.2.2.10.1.7 | NTPTimeStamp | read-only | SNTP Broadcast Last Response Time |
| INT rlSntpBroadcastStatus | 1.3.6.1.4.1.89.92.2.2.10.1.8 | INTEGER | read-only | The Operational State of the remote IP Address of the SNTP Broadcast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets. |
| NTP rlSntpBroadcastOffset | 1.3.6.1.4.1.89.92.2.2.10.1.9 | NTPTimeStamp | read-only | The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| NTP rlSntpBroadcastDelay | 1.3.6.1.4.1.89.92.2.2.10.1.10 | NTPSignedTimeValue | read-only | The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| ROW rlSntpBroadcastRowStatus | 1.3.6.1.4.1.89.92.2.2.10.1.11 | RowStatus | read-write | The Status of this SNTP broadcast interface information. |
| rlSntpConfigAnycastTable | 1.3.6.1.4.1.89.92.2.2.11 | not-accessible | A table containing anycast information per interface. | |
| rlSntpAnycastEntry | 1.3.6.1.4.1.89.92.2.2.11.1 | not-accessible | Private paramters for interface: server info. | |
| INT rlSntpAnycastIfIndex | 1.3.6.1.4.1.89.92.2.2.11.1.1 | INTEGER | not-accessible | The interface addressed by this entry. |
| IP rlSntpAnycastAddress | 1.3.6.1.4.1.89.92.2.2.11.1.2 | IpAddress | read-only | Ip Address of a trusted SNTP server. |
| NTP rlSntpAnycastStratum | 1.3.6.1.4.1.89.92.2.2.11.1.3 | NTPStratum | read-only | The stratum of this server. |
| NTP rlSntpAnycastLastResp | 1.3.6.1.4.1.89.92.2.2.11.1.4 | NTPTimeStamp | read-only | SNTP Anycast Last Response Time |
| INT rlSntpAnycastStatus | 1.3.6.1.4.1.89.92.2.2.11.1.5 | INTEGER | read-only | The Operational State of the remote IP Address of the SNTP Anycast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets. |
| NTP rlSntpAnycastOffset | 1.3.6.1.4.1.89.92.2.2.11.1.6 | NTPTimeStamp | read-only | The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| NTP rlSntpAnycastDelay | 1.3.6.1.4.1.89.92.2.2.11.1.7 | NTPSignedTimeValue | read-only | The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| ROW rlSntpAnycastRowStatus | 1.3.6.1.4.1.89.92.2.2.11.1.8 | RowStatus | read-write | The Status of this SNTP anycast interface information. |
| rlSntpConfigServerTable | 1.3.6.1.4.1.89.92.2.2.12 | not-accessible | A table containing trusted SNTP servers to be queried in unicast or broadcast mode. | |
| rlSntpServerEntry | 1.3.6.1.4.1.89.92.2.2.12.1 | not-accessible | A trusted server. | |
| IP rlSntpServerAddress | 1.3.6.1.4.1.89.92.2.2.12.1.1 | IpAddress | not-accessible | Ip Address of a trusted SNTP server. |
| T/F rlSntpServerPolled | 1.3.6.1.4.1.89.92.2.2.12.1.2 | TruthValue | read-write | TRUE if participating in polling cycle, else FALSE. |
| NTP rlSntpServerStratum | 1.3.6.1.4.1.89.92.2.2.12.1.3 | NTPStratum | read-only | The stratum of this server. |
| NTP rlSntpServerLastResp | 1.3.6.1.4.1.89.92.2.2.12.1.4 | NTPTimeStamp | read-only | SNTP Server Last Response Time |
| INT rlSntpServerStatus | 1.3.6.1.4.1.89.92.2.2.12.1.5 | INTEGER | read-only | The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets. |
| NTP rlSntpServersOffset | 1.3.6.1.4.1.89.92.2.2.12.1.6 | NTPTimeStamp | read-only | The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| NTP rlSntpServersDelay | 1.3.6.1.4.1.89.92.2.2.12.1.7 | NTPSignedTimeValue | read-only | The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| U32 rlSntpServersKeyIdentifier | 1.3.6.1.4.1.89.92.2.2.12.1.8 | Unsigned32 | read-write | Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done. |
| ROW rlSntpServerRowStatus | 1.3.6.1.4.1.89.92.2.2.12.1.9 | RowStatus | read-write | The Status of this SNTP server information. |
| rlSntpConfigAuthenticationTable | 1.3.6.1.4.1.89.92.2.2.13 | not-accessible | A table authentication keys. | |
| rlSntpAuthenticationEntry | 1.3.6.1.4.1.89.92.2.2.13.1 | not-accessible | Keys information for authenticationof NTP packets. | |
| U32 rlSntpAuthenticationKeyID | 1.3.6.1.4.1.89.92.2.2.13.1.1 | Unsigned32 | read-write | The key identifier. Valid rabge for key identifier is 1-4294967295. |
| STR rlSntpAuthenticationKeyValue | 1.3.6.1.4.1.89.92.2.2.13.1.2 | DisplayString | read-write | Key value. |
| INT rlSntpAuthenticationKeyState | 1.3.6.1.4.1.89.92.2.2.13.1.3 | INTEGER | read-write | Authentication key state - Enable/Disable key. |
| ROW rlSntpAuthenticationRowStatus | 1.3.6.1.4.1.89.92.2.2.13.1.4 | RowStatus | read-write | The Status of this Authentication key information. |
| INT rlSntpPort | 1.3.6.1.4.1.89.92.2.2.14 | INTEGER | read-write | User defined SNTP port. |
| rlSntpConfigBroadcastInetTable | 1.3.6.1.4.1.89.92.2.2.15 | not-accessible | A table containing broadcast mode information per interface. | |
| rlSntpBroadcastInetEntry | 1.3.6.1.4.1.89.92.2.2.15.1 | not-accessible | Private paramters for interface: sntp status, broadcast mode. | |
| INT rlSntpBroadcastInetIfIndex | 1.3.6.1.4.1.89.92.2.2.15.1.1 | INTEGER | not-accessible | The interface addressed by this entry. |
| INT rlSntpBroadcastInetIfAdminState | 1.3.6.1.4.1.89.92.2.2.15.1.2 | INTEGER | read-write | SNTP interface Adminstrative state- Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled. |
| INT rlSntpBroadcastInetMode | 1.3.6.1.4.1.89.92.2.2.15.1.3 | INTEGER | read-write | SNTP/NTP Broadcast Mode. none - no broadcast SNTP packets are received or sent. Receive - host only receive SNTP packets that were sent to broadcast address (were not directed to the host). This is multicast mode in the RFC. Send - host only send SNTP packets and wait for replies directed to the host. This is anycast mode in the RFC. ReceiveSend - host receive broadcast messages (destination is broadcast address in the received messages) and send SNTP packets to wait for replies directed to the host (destination address of the reply is the host address). This mode combines anycast and multicast modes in the RFC. |
| T/F rlSntpBroadcastInetPolled | 1.3.6.1.4.1.89.92.2.2.15.1.4 | TruthValue | read-write | TRUE if participating in polling cycle, else FALSE. |
| IPt rlSntpBroadcastInetAddressType | 1.3.6.1.4.1.89.92.2.2.15.1.5 | InetAddressType | read-only | Inet Address Type of a trusted SNTP server. |
| IP rlSntpBroadcastInetAddress | 1.3.6.1.4.1.89.92.2.2.15.1.6 | InetAddress | read-only | Inet Address of a trusted SNTP server. |
| NTP rlSntpBroadcastInetStratum | 1.3.6.1.4.1.89.92.2.2.15.1.7 | NTPStratum | read-only | The stratum of this server. |
| NTP rlSntpBroadcastInetLastResp | 1.3.6.1.4.1.89.92.2.2.15.1.8 | NTPTimeStamp | read-only | SNTP Broadcast Last Response Time |
| INT rlSntpBroadcastInetStatus | 1.3.6.1.4.1.89.92.2.2.15.1.9 | INTEGER | read-only | The Operational State of the remote IP Address of the SNTP Broadcast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets. |
| NTP rlSntpBroadcastInetOffset | 1.3.6.1.4.1.89.92.2.2.15.1.10 | NTPTimeStamp | read-only | The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| NTP rlSntpBroadcastInetDelay | 1.3.6.1.4.1.89.92.2.2.15.1.11 | NTPSignedTimeValue | read-only | The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| ROW rlSntpBroadcastInetRowStatus | 1.3.6.1.4.1.89.92.2.2.15.1.12 | RowStatus | read-write | The Status of this SNTP broadcast interface information. |
| rlSntpConfigAnycastInetTable | 1.3.6.1.4.1.89.92.2.2.16 | not-accessible | A table containing anycast information per interface. | |
| rlSntpAnycastInetEntry | 1.3.6.1.4.1.89.92.2.2.16.1 | not-accessible | Private paramters for interface: server info. | |
| INT rlSntpAnycastInetIfIndex | 1.3.6.1.4.1.89.92.2.2.16.1.1 | INTEGER | not-accessible | The interface addressed by this entry. |
| IPt rlSntpAnycastInetAddressType | 1.3.6.1.4.1.89.92.2.2.16.1.2 | InetAddressType | read-only | Inet Address Type of a trusted SNTP server. |
| IP rlSntpAnycastInetAddress | 1.3.6.1.4.1.89.92.2.2.16.1.3 | InetAddress | read-only | Inet Address of a trusted SNTP server. |
| NTP rlSntpAnycastInetStratum | 1.3.6.1.4.1.89.92.2.2.16.1.4 | NTPStratum | read-only | The stratum of this server. |
| NTP rlSntpAnycastInetLastResp | 1.3.6.1.4.1.89.92.2.2.16.1.5 | NTPTimeStamp | read-only | SNTP Anycast Last Response Time |
| INT rlSntpAnycastInetStatus | 1.3.6.1.4.1.89.92.2.2.16.1.6 | INTEGER | read-only | The Operational State of the remote IP Address of the SNTP Anycast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets. |
| NTP rlSntpAnycastInetOffset | 1.3.6.1.4.1.89.92.2.2.16.1.7 | NTPTimeStamp | read-only | The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| NTP rlSntpAnycastInetDelay | 1.3.6.1.4.1.89.92.2.2.16.1.8 | NTPSignedTimeValue | read-only | The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| ROW rlSntpAnycastInetRowStatus | 1.3.6.1.4.1.89.92.2.2.16.1.9 | RowStatus | read-write | The Status of this SNTP anycast interface information. |
| rlSntpConfigServerInetTable | 1.3.6.1.4.1.89.92.2.2.17 | not-accessible | A table containing trusted SNTP servers to be queried in unicast or broadcast mode. | |
| rlSntpServerInetEntry | 1.3.6.1.4.1.89.92.2.2.17.1 | not-accessible | A trusted server. | |
| IPt rlSntpServerInetAddressType | 1.3.6.1.4.1.89.92.2.2.17.1.1 | InetAddressType | not-accessible | Inet Address Type of a trusted SNTP server. |
| IP rlSntpServerInetAddress | 1.3.6.1.4.1.89.92.2.2.17.1.2 | InetAddress | not-accessible | Inet Address of a trusted SNTP server. |
| T/F rlSntpServerInetPolled | 1.3.6.1.4.1.89.92.2.2.17.1.3 | TruthValue | read-write | TRUE if participating in polling cycle, else FALSE. |
| NTP rlSntpServerInetStratum | 1.3.6.1.4.1.89.92.2.2.17.1.4 | NTPStratum | read-only | The stratum of this server. |
| NTP rlSntpServerInetLastResp | 1.3.6.1.4.1.89.92.2.2.17.1.5 | NTPTimeStamp | read-only | SNTP Server Last Response Time |
| INT rlSntpServerInetStatus | 1.3.6.1.4.1.89.92.2.2.17.1.6 | INTEGER | read-only | The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets. |
| NTP rlSntpServerInetOffset | 1.3.6.1.4.1.89.92.2.2.17.1.7 | NTPTimeStamp | read-only | The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| NTP rlSntpServerInetDelay | 1.3.6.1.4.1.89.92.2.2.17.1.8 | NTPSignedTimeValue | read-only | The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| U32 rlSntpServerInetKeyIdentifier | 1.3.6.1.4.1.89.92.2.2.17.1.9 | Unsigned32 | read-write | Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done. |
| ROW rlSntpServerInetRowStatus | 1.3.6.1.4.1.89.92.2.2.17.1.10 | RowStatus | read-write | The Status of this SNTP server information. |
| rlSntpAllServerInetTable | 1.3.6.1.4.1.89.92.2.2.18 | not-accessible | A table containing all SNTP servers (for example: statically configured, dynamically configured) to be queried in unicast or broadcast mode. | |
| rlSntpAllServerInetEntry | 1.3.6.1.4.1.89.92.2.2.18.1 | not-accessible | A server entry. | |
| INT rlSntpAllServerSource | 1.3.6.1.4.1.89.92.2.2.18.1.1 | INTEGER | not-accessible | The SNTP server source: static means manually defined, dhcpv6 means learnt from DHCP. Only static entries are stored in CDB. |
| NUM rlSntpAllServerIfIndex | 1.3.6.1.4.1.89.92.2.2.18.1.2 | InterfaceIndex | not-accessible | The ifIndex from which the SNTP server configuration was received (for dhcpv6 configurations). For static entries the value of this field will always be 1. |
| INT rlSntpAllServerPreference | 1.3.6.1.4.1.89.92.2.2.18.1.3 | INTEGER | not-accessible | The preference of SNTP server (for dhcpv6 configurations). For static entries the value of this field will always be 0. |
| IPt rlSntpAllServerInetAddressType | 1.3.6.1.4.1.89.92.2.2.18.1.4 | InetAddressType | not-accessible | SNTP server inet address type. |
| IP rlSntpAllServerInetAddress | 1.3.6.1.4.1.89.92.2.2.18.1.5 | InetAddress | not-accessible | SNTP server inet address. |
| T/F rlSntpAllServerInetPolled | 1.3.6.1.4.1.89.92.2.2.18.1.6 | TruthValue | read-only | TRUE if participating in polling cycle, else FALSE. |
| NTP rlSntpAllServerInetStratum | 1.3.6.1.4.1.89.92.2.2.18.1.7 | NTPStratum | read-only | The stratum of this server. |
| NTP rlSntpAllServerInetLastResp | 1.3.6.1.4.1.89.92.2.2.18.1.8 | NTPTimeStamp | read-only | SNTP Server Last Response Time |
| INT rlSntpAllServerInetStatus | 1.3.6.1.4.1.89.92.2.2.18.1.9 | INTEGER | read-only | The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets. |
| NTP rlSntpAllServerInetOffset | 1.3.6.1.4.1.89.92.2.2.18.1.10 | NTPTimeStamp | read-only | The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| NTP rlSntpAllServerInetDelay | 1.3.6.1.4.1.89.92.2.2.18.1.11 | NTPSignedTimeValue | read-only | The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030. |
| U32 rlSntpAllServerInetKeyIdentifier | 1.3.6.1.4.1.89.92.2.2.18.1.12 | Unsigned32 | read-write | Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done. |
| T/F rlSntpRestoreDefaultServers | 1.3.6.1.4.1.89.92.2.2.19 | TruthValue | read-write | Setting this scalar to true restores sntp default unicast servers. Meaning: all manually configured servers are deleted, and the default SNTP servers are recreated with their default values. This is an 'action' scalar. |
| rlNtpConfig | 1.3.6.1.4.1.89.92.2.3 |
RFC description
Manages SNTP and NTP time synchronization settings on Dell switches. Configures time server connectivity and clock synchronization methods.
Start monitoring Dell network switch (NTP/SNTP time sync) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.