| OID symbolic | OID numeric | Type | Access | Description |
|---|
| dgs6600VplsGenericMIB | 1.3.6.1.4.1.171.10.120.100.4.1 | | | Copyright (C) The IETF Trust (2012). The initial
version of this MIB module was published in RFC XXXX.
-- RFC Editor: Please replace XXXX with RFC number & remove
-- this note.
For full legal notices see the RFC itself or see:
http://www.ietf.org/copyrights/ianamib.html
This MIB module contains generic managed object definitions
for Virtual Private LAN Services as define in [RFC4762] and
[RFC4761]
This MIB module enables the use of any underlying Pseudowire
network. |
| vplsNotifications | 1.3.6.1.4.1.171.10.120.100.4.1.0 | | | |
| NTF vplsStatusChanged | 1.3.6.1.4.1.171.10.120.100.4.1.0.1 | | | The vplsStatusChanged notification is generated
when there is a change in the administrative or
operating status of a VPLS service. |
| NTF vplsFwdFullAlarmRaised | 1.3.6.1.4.1.171.10.120.100.4.1.0.2 | | | The vplsFwdFullAlarmRaised notification is
generated when the utilization of the Forwarding
database is above the value specified by
vplsConfigFwdFullHighWatermark. |
| NTF vplsFwdFullAlarmCleared | 1.3.6.1.4.1.171.10.120.100.4.1.0.3 | | | The vplsFwdFullAlarmCleared notification is
generated when the utilization of the Forwarding
database is below the value specified by
vplsConfigFwdFullLowWatermark. |
| vplsObjects | 1.3.6.1.4.1.171.10.120.100.4.1.1 | | | |
| U32 vplsConfigIndexNext | 1.3.6.1.4.1.171.10.120.100.4.1.1.1 | Unsigned32 | read-only | This object contains an appropriate value to be used
for vplsConfigIndex when creating entries in the
vplsConfigTable. The value 0 indicates that no
unassigned entries are available. To obtain the
value of vplsConfigIndex for a new entry in the
vplsConfigTable, the manager issues a management
protocol retrieval operation to obtain the current
value of vplsConfigIndex. After each retrieval
operation, the agent should modify the value to
reflect the next unassigned index. After a manager
retrieves a value the agent will determine through
its local policy when this index value will be made
available for reuse. |
| vplsConfigTable | 1.3.6.1.4.1.171.10.120.100.4.1.1.2 | | not-accessible | This table specifies information for configuring
and monitoring Virtual Private Lan Services(VPLS). |
| vplsConfigEntry | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1 | | not-accessible | A row in this table represents a Virtual Private Lan
Service(VPLS) in a packet network. It is indexed by
vplsConfigIndex, which uniquely identifies a single VPLS.
A row is created by the operator or by the agent if a
VPLS service is created by a non-SNMP application or
due to the Auto-Discovery process.
None of the read-create objects values can be
changed when vplsConfigRowStatus is in the active(1)
state. Changes are allowed when the vplsConfigRowStatus
is in notInService(2) or notReady(3) states only.
If the operator needs to change one of the values
for an active row the vplsConfigRowStatus should be
first changed to notInService(2), the objects may
then be changed, and finally the vplsConfigRowStatus
should be changed to active(1) in order to re-initiate
the signaling process with the new values in effect. |
| U32 vplsConfigIndex | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.1 | Unsigned32 | not-accessible | Unique index for the conceptual row identifying
a VPLS service. |
| STR vplsConfigName | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.2 | SnmpAdminString | read-create | A textual name of the VPLS.
If there is no local name, or this object is
otherwise not applicable, then this object MUST
contain a zero-length octet string. |
| STR vplsConfigDescr | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.3 | SnmpAdminString | read-create | A textual string containing information about the
VPLS service. If there is no information for this VPLS
service, then this object MUST contain a zero-length
octet string. |
| INT vplsConfigAdminStatus | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.4 | INTEGER | read-create | The desired administrative state of the VPLS
service. If the administrative status of the
VPLS service is changed to enabled then this
service is able to utilize pseudowires to
perform the tasks of a VPLS service.
The testing(3) state indicates that no operational
packets can be passed. |
| T/F vplsConfigMacLearning | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.6 | TruthValue | read-create | This object specifies if MAC Learning is enabled
in this service. If this object is true then MAC
Learning is enabled. If false, then MAC Learning is
disabled. |
| T/F vplsConfigDiscardUnknownDest | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.7 | TruthValue | read-create | If the value of this object is 'true', then frames
received with an unknown destination MAC are discarded
in this VPLS. If 'false', then the packets are
processed. |
| T/F vplsConfigMacAging | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.8 | TruthValue | read-create | If the value of this object is 'true'
then the MAC ageing process is enabled in
this VPLS. If 'false', then the MAC ageing process
is disabled |
| U32 vplsConfigFwdFullHighWatermark | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.10 | Unsigned32 | read-create | This object specifies the utilization of the
forwarding database for this VPLS instance at
which the vplsFwdFullAlarmRaised notification
will be sent. |
| U32 vplsConfigFwdFullLowWatermark | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.11 | Unsigned32 | read-create | This object specifies the utilization of the
forwarding database for this VPLS instance
at which the vplsFwdFullAlarmCleared
notification will be sent. |
| ROW vplsConfigRowStatus | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.12 | RowStatus | read-create | For creating, modifying, and deleting this row.
None of the read-create objects in the
conceptual rows may be changed when this
object is in the active(1) state. |
| U32 vplsConfigMtu | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.13 | Unsigned32 | read-create | The value of this object specifies the MTU of this
vpls instance. This can be used to limit the MTU to a
value lower than the MTU supported by the associated
Pseudowires |
| VPN vplsConfigVpnId | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.14 | VPNIdOrZero | read-only | This objects indicates the IEEE 802-1990
VPN ID of the associated VPLS service. |
| STO vplsConfigStorageType | 1.3.6.1.4.1.171.10.120.100.4.1.1.2.1.15 | StorageType | read-create | This variable indicates the storage type for this row. |
| vplsStatusTable | 1.3.6.1.4.1.171.10.120.100.4.1.1.3 | | not-accessible | This table provides information for monitoring
Virtual Private Lan Services (VPLS). |
| vplsStatusEntry | 1.3.6.1.4.1.171.10.120.100.4.1.1.3.1 | | not-accessible | A row in this table represents a Virtual Private Lan
Service(VPLS) in a packet network. It is indexed by
vplsConfigIndex, which uniquely identifies a single VPLS.
A row in this table is automatically created by the agent
when a VPLS service is configured. |
| INT vplsStatusOperStatus | 1.3.6.1.4.1.171.10.120.100.4.1.1.3.1.1 | INTEGER | read-only | The current operational state of this VPLS Service. |
| C32 vplsStatusPeerCount | 1.3.6.1.4.1.171.10.120.100.4.1.1.3.1.2 | Counter32 | read-only | This objects specifies the number of peers
(pseudowires) present in this VPLS instance. |
| vplsPwBindTable | 1.3.6.1.4.1.171.10.120.100.4.1.1.4 | | not-accessible | This table provides an association between a
VPLS service and the corresponding pseudowires.
A service can have more than one pseudowire
association. Pseudowires are defined in
the pwTable |
| vplsPwBindEntry | 1.3.6.1.4.1.171.10.120.100.4.1.1.4.1 | | not-accessible | Each row represents an association between a
VPLS instance and one or more pseudowires
defined in the pwTable. Each index is unique
in describing an entry in this table. However
both indexes are required to define the one
to many association of service to
pseudowire. |
| INT vplsPwBindConfigType | 1.3.6.1.4.1.171.10.120.100.4.1.1.4.1.1 | INTEGER | read-create | The value of this object indicates
whether the Pseudo Wire binding was created
manually or via Auto-Discovery.
The value of this object must be
specifed when the row is created and cannot
be changed while the row status is active(1) |
| INT vplsPwBindType | 1.3.6.1.4.1.171.10.120.100.4.1.1.4.1.2 | INTEGER | read-create | The value of this object indicates
whether the pseudowire binding is of
type mesh or spoke.
The value of this object must be
specified when the row is created and cannot
be changed while the row status is active(1) |
| ROW vplsPwBindRowStatus | 1.3.6.1.4.1.171.10.120.100.4.1.1.4.1.3 | RowStatus | read-create | For creating, modifying, and deleting this row.
None of the read-create objects in the
conceptual rows may be changed when this
object is in the active(1) state |
| STO vplsPwBindStorageType | 1.3.6.1.4.1.171.10.120.100.4.1.1.4.1.4 | StorageType | read-create | This variable indicates the storage type for this row. |
| vplsBgpADConfigTable | 1.3.6.1.4.1.171.10.120.100.4.1.1.5 | | not-accessible | This table specifies information for configuring
BGP Auto-Discovery parameters for a given VPLS service. |
| vplsBgpADConfigEntry | 1.3.6.1.4.1.171.10.120.100.4.1.1.5.1 | | not-accessible | A row in this table indicates that BGP based Auto-
Discovery is in use for this instance of VPLS.
A row in this table is indexed by vplsConfigIndex, which
uniquely identifies a single VPLS.
None of the read-create objects can be changed when
vplsBGPADConfigRowStatus is in active(1) state. Changes
are allowed when the vplsBGPADConfigRowStatus is in
notInService(2) or notReady(3) states only.
If the operator needs to change one of the values
for an active row the vplsConfigRowStatus should be
first changed to notInService(2), the objects may
then be changed, and finally the vplsConfigRowStatus
should be changed to active(1) in order to
re-initiate the signaling process with the new
values in effect. |
| VPL vplsBgpADConfigRouteDistinguisher | 1.3.6.1.4.1.171.10.120.100.4.1.1.5.1.1 | VplsBgpRouteDistinguisher | read-create | The route distinguisher for this VPLS. See [RFC4364]
for a complete definition of a route distinguisher.
for more details on use of a route distinguisher
for a VPLS service, see [RFC4761]. When not configured, the
value is derived from the lower 6 bytes of
vplsBgpADConfigVplsId. |
| U32 vplsBgpADConfigPrefix | 1.3.6.1.4.1.171.10.120.100.4.1.1.5.1.2 | Unsigned32 | read-create | In case of auto-discovery the default prefix advertised
is the IP address of the loopback. In case the user wants
to override the loopback address, vplsBgpADConfigPrefix
should be set. When this value is non-zero this value is
used along with vplsBgpADConfigRouteDistinguisher in the
NLRI, see [RFC 6074] |
| VPL vplsBgpADConfigVplsId | 1.3.6.1.4.1.171.10.120.100.4.1.1.5.1.3 | VplsBgpRouteDistinguisher | read-create | VplsId is a unique identifier for all VSIs belonging to
the same VPLS. It is advertised as an extended community. |
| ROW vplsBgpADConfigRowStatus | 1.3.6.1.4.1.171.10.120.100.4.1.1.5.1.4 | RowStatus | read-create | For creating, modifying, and deleting this row.
None of the read-create objects in the
conceptual rows may be changed when this
object is in the active(1) state. |
| T/F vplsStatusNotifEnable | 1.3.6.1.4.1.171.10.120.100.4.1.1.7 | TruthValue | read-write | If this object is set to true(1), then it enables
the emission of vplsStatusChanged
notification; otherwise this notification is not
emitted. |
| U32 vplsNotificationMaxRate | 1.3.6.1.4.1.171.10.120.100.4.1.1.8 | Unsigned32 | read-write | This object indicates the maximum number of
notifications issued per second. If events occur
more rapidly, the implementation may simply fail to
emit these notifications during that period, or may
queue them until an appropriate time. A value of 0
means no throttling is applied and events may be
notified at the rate at which they occur. |
| vplsConformance | 1.3.6.1.4.1.171.10.120.100.4.1.2 | | | |
| vplsCompliances | 1.3.6.1.4.1.171.10.120.100.4.1.2.1 | | | |
| vplsModuleFullCompliance | 1.3.6.1.4.1.171.10.120.100.4.1.2.1.1 | | | Compliance requirement for implementations that
provide full support for VPLS-GENERIC-MIB.
Such devices can then be monitored and configured using
this MIB module. |
| vplsModuleReadOnlyCompliance | 1.3.6.1.4.1.171.10.120.100.4.1.2.1.2 | | | Compliance requirement for implementations that only
provide read-only support for VPLS-GENERIC-MIB.
Such devices can then be monitored but cannot be
configured using this MIB modules. |
| vplsGroups | 1.3.6.1.4.1.171.10.120.100.4.1.2.2 | | | |
| vplsGroup | 1.3.6.1.4.1.171.10.120.100.4.1.2.2.1 | | | The group of objects supporting
management of L2VPN VPLS services |
| vplsPwBindGroup | 1.3.6.1.4.1.171.10.120.100.4.1.2.2.2 | | | The group of objects supporting
management of
Pseudo Wire (PW) Binding to VPLS. |
| vplsNotificationGroup | 1.3.6.1.4.1.171.10.120.100.4.1.2.2.3 | | | The group of notifications supporting
the Notifications generated for
VPLS Services |
