DGS-3700-12G-L2MGMT-MIB

All MIBs › DGS-3700-12G-L2MGMT-MIB

Organization: D-Link Corp.

Last Updated: 2008-03-10

Category: Technology: Switching/L2, Vendor: D-Link

Description: L2 management MIB for D-Link DGS-3700-12G 12-port Gigabit switch variant covering VLANs, STP, and L2 management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DGS-3700-12G-L2MGMT-MIB?

DGS-3700-12G-L2MGMT-MIB is a D-Link proprietary MIB defining Layer 2 network management information for the DGS-3700-12G managed switch. Its objects cover front-panel LED status, port counts, spanning-tree state, IGMP snooping, SNMP trap state, statistics-counter reset, FDB-table VLAN scoping, MAC-notification state/history-size/interval, Telnet/Web state and TCP port, management VLAN ID, LLDP state and forwarding, IP auto-configuration, and CFM (Connectivity Fault Management) state and per-port configuration. As a configuration/status MIB it lets an administrator confirm core Layer 2 management settings — spanning tree, IGMP snooping, management VLAN — are configured as intended on the switch. It is deployed on the D-Link DGS-3700-12G managed switch. Engineers can download the DGS-3700-12G-L2MGMT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DGS-3700-12G-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DGS-3700-12G managed switch

Monitoring Examples

An administrator checks swL2DevCtrlStpState and swL2DevCtrlIGMPSnooping to confirm spanning-tree and multicast-snooping are both enabled as expected on a D-Link DGS-3700-12G switch.

What Can Be Monitored

spanning-tree, IGMP snooping, and management VLAN configuration

Imported Objects

From DLINK-ID-REC-MIB

AgentNotifyLevel

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

From SW3700PRIMGMT-MIB

dgs3712g

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL2MgmtMIB	1.3.6.1.4.1.171.11.102.1.2.2			The Structure of Layer 2 Network Management Information.
swL2DevMgmt	1.3.6.1.4.1.171.11.102.1.2.2.1
swL2DevInfo	1.3.6.1.4.1.171.11.102.1.2.2.1.1
INT swDevInfoTotalNumOfPort	1.3.6.1.4.1.171.11.102.1.2.2.1.1.1	INTEGER	read-only	The number of ports within this switch. This value is the sum of the ports within this switch.
INT swDevInfoNumOfPortInUse	1.3.6.1.4.1.171.11.102.1.2.2.1.1.2	INTEGER	read-only	The number of ports in this switch connected to the segment or the end stations.
OCT swDevInfoFrontPanelLedStatus	1.3.6.1.4.1.171.11.102.1.2.2.1.1.4	OCTET STRING	read-only	This object is a set of system LED indications. The first four octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The other octets are the logical port LED. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. System LED: 01 = fail/error/non existence. 02 = work normal Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
swL2DevCtrl	1.3.6.1.4.1.171.11.102.1.2.2.1.2
INT swL2DevCtrlStpState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.1	INTEGER	read-write	This object can enable or disable the spanning tree algorithm during the runtime of the system.
INT swL2DevCtrlIGMPSnooping	1.3.6.1.4.1.171.11.102.1.2.2.1.2.2	INTEGER	read-write	This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
INT swL2DevCtrlSnmpTrapState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.5	INTEGER	read-write	This object controls the SNMP trap status.
INT swL2DevCtrlCleanAllStatisticCounter	1.3.6.1.4.1.171.11.102.1.2.2.1.2.6	INTEGER	read-write	When the object is set to active, all statistical counters will be cleared. If set to normal, no action.
VLA swL2DevCtrlVlanIdOfFDBTbl	1.3.6.1.4.1.171.11.102.1.2.2.1.2.7	VlanId	read-write	Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.
INT swL2MACNotifyState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.8	INTEGER	read-write	This object can enable or disable MAC Notification.
INT swL2MACNotifyHistorySize	1.3.6.1.4.1.171.11.102.1.2.2.1.2.9	INTEGER	read-write	This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .
INT swL2MACNotifyInterval	1.3.6.1.4.1.171.11.102.1.2.2.1.2.10	INTEGER	read-write	This object indicates the time interval, in seconds, which will trigger MAC notification messages.
swL2DevCtrlTelnet	1.3.6.1.4.1.171.11.102.1.2.2.1.2.14
INT swL2DevCtrlTelnetState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.14.1	INTEGER	read-write	This object controls the Telnet status.
INT swL2DevCtrlTelnetTcpPort	1.3.6.1.4.1.171.11.102.1.2.2.1.2.14.2	INTEGER	read-write	This object designates TCP ports. When Telnet is disabled, this object is not accessible.
VLA swL2DevCtrlManagementVlanId	1.3.6.1.4.1.171.11.102.1.2.2.1.2.16	VlanId	read-write	This object controls which previously created VLANs are included in the System IP Interface.
swL2DevCtrlWeb	1.3.6.1.4.1.171.11.102.1.2.2.1.2.17
INT swL2DevCtrlWebState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.17.1	INTEGER	read-write	This object controls the Web status.
INT swL2DevCtrlWebTcpPort	1.3.6.1.4.1.171.11.102.1.2.2.1.2.17.2	INTEGER	read-write	This object designates TCP ports. When Web is disabled, this object is not accessible.
INT swL2DevCtrlLLDPState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.18	INTEGER	read-write	Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
INT swL2DevCtrlLLDPForwardMessageState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.19	INTEGER	read-write	When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded.
INT swL2DevCtrlIpAutoconfig	1.3.6.1.4.1.171.11.102.1.2.2.1.2.20	INTEGER	read-write	This object controls the IP auto configuration state.
swL2DevCtrlCFM	1.3.6.1.4.1.171.11.102.1.2.2.1.2.21
INT swL2DevCtrlCFMState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.21.1	INTEGER	read-write	This object indicates the CFM global state.
swL2DevCtrlCFMPortTable	1.3.6.1.4.1.171.11.102.1.2.2.1.2.21.2		not-accessible	A table containing CFM state of speicified ports.
swL2DevCtrlCFMPortEntry	1.3.6.1.4.1.171.11.102.1.2.2.1.2.21.2.1		not-accessible	The entry of CFM state on speicified ports.
INT swL2DevCtrlCFMPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.1.2.21.2.1.1	INTEGER	not-accessible	This object indicates the port-num.
INT swL2DevCtrlCFMPortState	1.3.6.1.4.1.171.11.102.1.2.2.1.2.21.2.1.2	INTEGER	read-write	This object indicates the CFM state on per-port.
swL2DevAlarm	1.3.6.1.4.1.171.11.102.1.2.2.1.3
INT swL2DevAlarmNewRoot	1.3.6.1.4.1.171.11.102.1.2.2.1.3.1	INTEGER	read-write	When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.
INT swL2DevAlarmTopologyChange	1.3.6.1.4.1.171.11.102.1.2.2.1.3.2	INTEGER	read-write	This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other.
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.171.11.102.1.2.2.1.3.3	INTEGER	read-write	This object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other.
swL2VLANMgmt	1.3.6.1.4.1.171.11.102.1.2.2.2
swL2VlanStaticTable	1.3.6.1.4.1.171.11.102.1.2.2.2.1		not-accessible	A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
swL2VlanStaticEntry	1.3.6.1.4.1.171.11.102.1.2.2.2.1.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
VLA swL2VlanIndex	1.3.6.1.4.1.171.11.102.1.2.2.2.1.1.1	VlanId	not-accessible	The VLAN-ID or other identifier referring to this VLAN.
INT swL2VLANAdvertisement	1.3.6.1.4.1.171.11.102.1.2.2.2.1.1.2	INTEGER	read-write	This object indicates if the advertisement is active or not.
INT swL2PVIDAutoAssignmentState	1.3.6.1.4.1.171.11.102.1.2.2.2.2	INTEGER	read-write	This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned 'default VLAN'.
swL2VlanPortInfoTable	1.3.6.1.4.1.171.11.102.1.2.2.2.3		not-accessible	A table containing vlan and port role information of each port.
swL2VlanPortInfoEntry	1.3.6.1.4.1.171.11.102.1.2.2.2.3.1		not-accessible	The table entry of vlan port information.
INT swL2VlanPortInfoPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.2.3.1.1	INTEGER	read-only	The port index.
INT swL2VlanPortInfoVid	1.3.6.1.4.1.171.11.102.1.2.2.2.3.1.2	INTEGER	read-only	The VLAN-ID assigned to a special port
INT swL2VlanPortInfoPortRole	1.3.6.1.4.1.171.11.102.1.2.2.2.3.1.3	INTEGER	read-only	The port role of a special port.when none,it means this port is not belong to the vlan.
INT swL2NniGvrpBpduAddress	1.3.6.1.4.1.171.11.102.1.2.2.2.7	INTEGER	read-write	Specifies the GVRP's BPDU MAC address of NNI port In Q-in_Q status.
swL2PortMgmt	1.3.6.1.4.1.171.11.102.1.2.2.3
swL2PortInfoTable	1.3.6.1.4.1.171.11.102.1.2.2.3.1		not-accessible	A table that contains information about every port.
swL2PortInfoEntry	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1		not-accessible	A list of information for each port of the device.
INT swL2PortInfoPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortInfoMediumType	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1.2	INTEGER	read-only	Indicates medium type of the port number.
INT swL2PortInfoUnitID	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1.3	INTEGER	read-only	Indicates ID of the unit in the system
INT swL2PortInfoType	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1.4	INTEGER	read-only	This object indicates the connector type of this port.
INT swL2PortInfoLinkStatus	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1.5	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInfoNwayStatus	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1.6	INTEGER	read-only	This object indicates the port speed and duplex mode.
INT swL2PortInfoErrorDisabled	1.3.6.1.4.1.171.11.102.1.2.2.3.1.1.8	INTEGER	read-only	This object indicates the blocking type of this port.
swL2PortCtrlTable	1.3.6.1.4.1.171.11.102.1.2.2.3.2		not-accessible	A table that contains control information about every port.
swL2PortCtrlEntry	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1		not-accessible	A list of control information for each port of the device.
INT swL2PortCtrlPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCtrlMediumType	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.2	INTEGER	read-only	Indicates medium type of the port number.
INT swL2PortCtrlUnitIndex	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.3	INTEGER	read-only	Indicates ID of the unit in the device
INT swL2PortCtrlAdminState	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.4	INTEGER	read-write	This object decides if the port is enabled or disabled.
INT swL2PortCtrlNwayState	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.5	INTEGER	read-write	Chose the port speed, duplex mode, and N-Way function mode.
INT swL2PortCtrlFlowCtrlState	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.6	INTEGER	read-write	The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
INT swL2PortCtrlLearningState	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.7	INTEGER	read-write	This object decides if the port is locked or not.
INT swL2PortCtrlMACNotifyState	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.8	INTEGER	read-write	This object sets each port's MAC notification state.
INT swL2PortCtrlMDIXState	1.3.6.1.4.1.171.11.102.1.2.2.3.2.1.10	INTEGER	read-write	This object configures the MDIX setting of the port.
INT swL2PortCtrlJumboFrame	1.3.6.1.4.1.171.11.102.1.2.2.3.3	INTEGER	read-write	This object configures the switch's jumbo frame settings.
INT swL2PortCtrlJumboFrameMaxSize	1.3.6.1.4.1.171.11.102.1.2.2.3.4	INTEGER	read-only	This object describes how many bytes the max jumbo frame is.
swL2PortCounterCtrlTable	1.3.6.1.4.1.171.11.102.1.2.2.3.6		not-accessible	A table that used to clear counter information about every port.
swL2PortCounterCtrlEntry	1.3.6.1.4.1.171.11.102.1.2.2.3.6.1		not-accessible	A list of entry used to clear counter information for each port of the device.
INT swL2PortCounterCtrlPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.3.6.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCounterClearCtrl	1.3.6.1.4.1.171.11.102.1.2.2.3.6.1.2	INTEGER	read-write	This object indicates if to clear the counters for each port of the device or not.
swL2PortErrTable	1.3.6.1.4.1.171.11.102.1.2.2.3.7		not-accessible	A table that contains error information for each port.
swL2PortErrEntry	1.3.6.1.4.1.171.11.102.1.2.2.3.7.1		not-accessible	A list of information regarding port errors on the device.
INT swL2PortErrPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.3.7.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module).
INT swL2PortErrPortState	1.3.6.1.4.1.171.11.102.1.2.2.3.7.1.2	INTEGER	read-only	This object indicates the port state is enabled or disabled.
INT swL2PortErrPortConnStatus	1.3.6.1.4.1.171.11.102.1.2.2.3.7.1.3	INTEGER	read-only	This object indicates whether the PortStatus is err-disabled or not.
INT swL2PortErrPortReason	1.3.6.1.4.1.171.11.102.1.2.2.3.7.1.4	INTEGER	read-only	This object describes if the reason for the port error is STP LBD or Storm control.
swL2DhcpRelayMgmt	1.3.6.1.4.1.171.11.102.1.2.2.8
swL2TrunkMgmt	1.3.6.1.4.1.171.11.102.1.2.2.9
INT swL2TrunkMaxSupportedEntries	1.3.6.1.4.1.171.11.102.1.2.2.9.1	INTEGER	read-only	Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
INT swL2TrunkCurrentNumEntries	1.3.6.1.4.1.171.11.102.1.2.2.9.2	INTEGER	read-only	Current active number of entries in the trunk configuration table.
swL2TrunkCtrlTable	1.3.6.1.4.1.171.11.102.1.2.2.9.3		not-accessible	This table specifies which ports group a set of ports(up to 8) into a single logical link.
swL2TrunkCtrlEntry	1.3.6.1.4.1.171.11.102.1.2.2.9.3.1		not-accessible	A list of information that specifies which ports group a set of ports(up to 8) into a single logical link.
INT swL2TrunkIndex	1.3.6.1.4.1.171.11.102.1.2.2.9.3.1.1	INTEGER	read-only	The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.
INT swL2TrunkMasterPort	1.3.6.1.4.1.171.11.102.1.2.2.9.3.1.3	INTEGER	read-create	The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
POR swL2TrunkMember	1.3.6.1.4.1.171.11.102.1.2.2.9.3.1.4	PortList	read-create	Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.
INT swL2TrunkFloodingPort	1.3.6.1.4.1.171.11.102.1.2.2.9.3.1.5	INTEGER	read-only	The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.
INT swL2TrunkType	1.3.6.1.4.1.171.11.102.1.2.2.9.3.1.6	INTEGER	read-create	This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group .
ROW swL2TrunkState	1.3.6.1.4.1.171.11.102.1.2.2.9.3.1.7	RowStatus	read-create	This object indicates the status of this entry.
INT swL2TrunkAlgorithm	1.3.6.1.4.1.171.11.102.1.2.2.9.4	INTEGER	read-write	This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
swL2TrunkLACPPortTable	1.3.6.1.4.1.171.11.102.1.2.2.9.5		not-accessible	This table specifies which ports group a set of ports(up to 8) into a single logical link.
swL2TrunkLACPPortEntry	1.3.6.1.4.1.171.11.102.1.2.2.9.5.1		not-accessible	A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
INT swL2TrunkLACPPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.9.5.1.1	INTEGER	read-only	The index of logical port LACP.
INT swL2TrunkLACPPortState	1.3.6.1.4.1.171.11.102.1.2.2.9.5.1.2	INTEGER	read-write	The state of logical port LACP.
swL2MirrorMgmt	1.3.6.1.4.1.171.11.102.1.2.2.10
INT swL2MirrorLogicTargetPort	1.3.6.1.4.1.171.11.102.1.2.2.10.1	INTEGER	read-write	This object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
POR swL2MirrorPortSourceIngress	1.3.6.1.4.1.171.11.102.1.2.2.10.2	PortList	read-write	This represents the port where ingress packets will be sniffed.
POR swL2MirrorPortSourceEgress	1.3.6.1.4.1.171.11.102.1.2.2.10.3	PortList	read-write	This represents the port where egress packets will be sniffed.
INT swL2MirrorPortState	1.3.6.1.4.1.171.11.102.1.2.2.10.4	INTEGER	read-write	This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table.
swL2TrafficSegMgmt	1.3.6.1.4.1.171.11.102.1.2.2.14
swL2TrafficSegTable	1.3.6.1.4.1.171.11.102.1.2.2.14.1		not-accessible	This table specifies that the port can just forward traffic to the specific port list.
swL2TrafficSegEntry	1.3.6.1.4.1.171.11.102.1.2.2.14.1.1		not-accessible	A list of information which specifies the port with its traffic forwarding list.
INT swL2TrafficSegPort	1.3.6.1.4.1.171.11.102.1.2.2.14.1.1.1	INTEGER	read-only	The port number of the logical port.
POR swL2TrafficSegForwardPorts	1.3.6.1.4.1.171.11.102.1.2.2.14.1.1.2	PortList	read-write	The port list to which the specific port can forward traffic.
swL2MulticastFilterMode	1.3.6.1.4.1.171.11.102.1.2.2.17
swL2MulticastFilterModeVlanTable	1.3.6.1.4.1.171.11.102.1.2.2.17.1		not-accessible	A table that contains information about VLAN multicast filter mode.
swL2MulticastFilterModeVlanEntry	1.3.6.1.4.1.171.11.102.1.2.2.17.1.1		not-accessible	A list of multicast filter mode information for each VLAN.
INT swL2MulticastFilterVid	1.3.6.1.4.1.171.11.102.1.2.2.17.1.1.1	INTEGER	read-only	Indicates VID for each VLAN.
INT swL2MulticastFilterVlanMode	1.3.6.1.4.1.171.11.102.1.2.2.17.1.1.2	INTEGER	read-write	Specifies multicast filter mode for each VLAN.
swL2LoopDetectMgmt	1.3.6.1.4.1.171.11.102.1.2.2.18
swL2LoopDetectCtrl	1.3.6.1.4.1.171.11.102.1.2.2.18.1
INT swL2LoopDetectAdminState	1.3.6.1.4.1.171.11.102.1.2.2.18.1.1	INTEGER	read-write	This object indicates the loopback detection status for the system.
INT swL2LoopDetectInterval	1.3.6.1.4.1.171.11.102.1.2.2.18.1.2	INTEGER	read-write	This object indicates the interval value, the range is from 1 to 32767 seconds.
INT swL2LoopDetectRecoverTime	1.3.6.1.4.1.171.11.102.1.2.2.18.1.3	INTEGER	read-write	This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
INT swL2LoopDetectMode	1.3.6.1.4.1.171.11.102.1.2.2.18.1.4	INTEGER	read-write	This object indicates the loopback detection mode for the system.
INT swL2LoopDetectTrapMode	1.3.6.1.4.1.171.11.102.1.2.2.18.1.5	INTEGER	read-write	This object indicates the loopback detection trap mode for the system.
swL2LoopDetectPortMgmt	1.3.6.1.4.1.171.11.102.1.2.2.18.2
swL2LoopDetectPortTable	1.3.6.1.4.1.171.11.102.1.2.2.18.2.1		not-accessible	The table specifies the loopback detection function specified by port.
swL2LoopDetectPortEntry	1.3.6.1.4.1.171.11.102.1.2.2.18.2.1.1		not-accessible	The table specifies the loopback detection function specified by port.
INT swL2LoopDetectPortIndex	1.3.6.1.4.1.171.11.102.1.2.2.18.2.1.1.1	INTEGER	read-only	This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
INT swL2LoopDetectPortState	1.3.6.1.4.1.171.11.102.1.2.2.18.2.1.1.2	INTEGER	read-write	This object indicates the loopback detection function state on the port.
STR swL2LoopDetectPortLoopVLAN	1.3.6.1.4.1.171.11.102.1.2.2.18.2.1.1.3	DisplayString	read-only	This object indicates the VLAN list that has detected a loopback.
INT swL2LoopDetectPortLoopStatus	1.3.6.1.4.1.171.11.102.1.2.2.18.2.1.1.4	INTEGER	read-only	This object indicates the port status.
swL2DhcpLocalRelayMgmt	1.3.6.1.4.1.171.11.102.1.2.2.24
INT swL2DhcpLocalRelayState	1.3.6.1.4.1.171.11.102.1.2.2.24.1	INTEGER	read-write	This object indicates the status of the DHCP local relay function of the switch.
swL2DhcpLocalRelayVLANTable	1.3.6.1.4.1.171.11.102.1.2.2.24.2		not-accessible	This table is used to manage the DHCP local relay status for each VLAN.
swL2DhcpLocalRelayVLANEntry	1.3.6.1.4.1.171.11.102.1.2.2.24.2.1		not-accessible	This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
INT swL2DhcpLocalRelayVLANID	1.3.6.1.4.1.171.11.102.1.2.2.24.2.1.1	INTEGER	read-only	This object shows the VIDs of the current VLANS in the switch.
INT swL2DhcpLocalRelayVLANState	1.3.6.1.4.1.171.11.102.1.2.2.24.2.1.2	INTEGER	read-write	This object indicates the status of the DHCP relay function of the VLAN.
swL2MgmtMIBTraps	1.3.6.1.4.1.171.11.102.1.2.2.100
swL2Notify	1.3.6.1.4.1.171.11.102.1.2.2.100.1
swL2NotifyMgmt	1.3.6.1.4.1.171.11.102.1.2.2.100.1.1
swL2NotifyPrefix	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2
swL2NotifFirmware	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.0
NTF swL2macNotification	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.0.1			This trap indicates the MAC addresses variation in address table .
NTF swL2PortLoopOccurred	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.0.3			The trap is sent when a Port loop occurs.
NTF swL2PortLoopRestart	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.0.4			The trap is sent when a Port loop restarts after the interval time.
NTF swL2VlanLoopOccurred	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.0.5			The trap is sent when a Port with a VID loop occurs.
NTF swL2VlanLoopRestart	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.0.6			The trap is sent when a Port with a VID loop restarts after the interval time.
swl2NotificationBidings	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.1
OCT swL2macNotifyInfo	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.1.1	OCTET STRING	read-only	This object indicates the last time reboot information.
INT swL2VlanLoopDetectVID	1.3.6.1.4.1.171.11.102.1.2.2.100.1.2.1.3	INTEGER	accessible-for-notify	This object indicates the VID that detected a loopback.

RFC description

Manages Layer 2 settings on DGS-3700 switches including ports, VLAN, QoS, DHCP relay, and spanning tree protocol.

Start monitoring D-Link DGS-3700-12G managed switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DGS-3700-12G-L2MGMT-MIB

What Is DGS-3700-12G-L2MGMT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description