DGS-3120-48PC-L3MGMT-MIB

All MIBs › DGS-3120-48PC-L3MGMT-MIB

Last Updated: 2012-11-16

Category: Technology: PoE, Technology: Routing/L3, Vendor: D-Link

Description: L3 management MIB for D-Link DGS-3120-48PC 48-port PoE switch covering Layer 3 routing and advanced management features.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DGS-3120-48PC-L3MGMT-MIB?

This proprietary D-Link MIB defines Layer 3 network management information for the DGS-3120-48PC, a 48-port PoE Gigabit switch with routing capability, covering configuration of routing protocols, ACLs, and other L3 features layered on top of its L2 switching function. Rather than raw traffic counters, it exposes L3 protocol and routing-configuration state specific to this switch's advanced feature set. As a monitoring target it is used to verify the health and correctness of routing-plane configuration, confirming routing protocol adjacencies, route table state, and L3 ACL enforcement are behaving as intended on a switch that also has to manage PoE power delivery to connected endpoints. It is a proprietary companion to D-Link's L2-management and resource-management MIBs for the same switch family rather than an IETF standard, and typically complements standard routing MIBs (e.g., OSPF-MIB) where applicable. It is deployed on DGS-3120-48PC switches in campus or building-distribution layers requiring both PoE endpoint power and Layer 3 routing between VLANs, and administrators can download the DGS-3120-48PC-L3MGMT-MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DGS-3120-48PC-L3MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DGS-3120-48PC PoE switch

Monitoring Examples

No sample object or table names were provided for this module in the supplied excerpt, so a concrete OID-level example cannot be given. Based on sibling D-Link L3MGMT MIBs (e.g., DVMRP interface tables and OSPF ECMP objects seen in the DGS3000-series L3MGMT modules), a realistic scenario would involve polling routing-interface and route-preference tables to confirm routes are correctly learned and installed. This description is inferred from the module's stated purpose since no named objects were supplied.

What Can Be Monitored

Layer 3 routing configuration state
ACL enforcement status
routing protocol status
PoE port power status

Imported Objects

From IPV6-TC

Ipv6Address

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
PhysAddress
RowStatus
TruthValue

From SWDGS3120PRIMGMT-MIB

dlink-Dgs3120Proj-Dgs3120-48PC

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL3MgmtMIB	1.3.6.1.4.1.171.11.117.1.5.3			The Structure of Layer 3 Network Management Information for the proprietary enterprise.
swL3IpMgmt	1.3.6.1.4.1.171.11.117.1.5.3.2
swL3IpCtrlMgmt	1.3.6.1.4.1.171.11.117.1.5.3.2.1
swL3IpCtrlTable	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3		not-accessible	This table contain IP interface information.
swL3IpCtrlEntry	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1		not-accessible	A list of information about a specific IP interface.
STR swL3IpCtrlInterfaceName	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.1	DisplayString	read-only	This object indicates the name of the IP interface.
INT swL3IpCtrlIfIndex	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.2	INTEGER	read-only	This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
IP swL3IpCtrlIpAddr	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.3	IpAddress	read-write	The IP address of the interface. This object only can take the value of the unicast IP address.
IP swL3IpCtrlIpSubnetMask	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.4	IpAddress	read-write	The IP net mask for this interface.
STR swL3IpCtrlVlanName	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.5	DisplayString	read-write	This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
INT swL3IpCtrlProxyArp	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.6	INTEGER	read-write	This object indicates enable/disable of the proxy ARP function for IPv4.
T/F swL3IpCtrlSecondary	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.7	TruthValue	read-write	When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.
INT swL3IpCtrlMode	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.8	INTEGER	read-write	This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server.
INT swL3IpCtrlAdminState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.9	INTEGER	read-write	The state of the IP interface.
INT swL3IpCtrlIpv4AdminState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.10	INTEGER	read-write	The IPv4 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.
INT swL3IpCtrlIpv6AdminState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.12	INTEGER	read-write	The IPv6 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.
ADR swL3IpCtrlIpv6LinkLocalAddress	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.14	Ipv6Address	read-only	The IPv6 link local address for this interface.
INT swL3IpCtrlIpv6LinkLocalPrefixLen	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.15	INTEGER	read-only	The IPv6 prefix length for this IPv6 link local address.
ROW swL3IpCtrlState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.16	RowStatus	read-create	This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
INT swL3IpCtrlIpv6LinkLocalAutoState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.17	INTEGER	read-write	The state of the IPv6 link local auto.
INT swL3IpCtrlLocalProxyArp	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.18	INTEGER	read-write	This object indicates enable/disable of the local proxy ARP function for IPv4.
INT swL3IpCtrlDhcpv6ClientState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.20	INTEGER	read-write	The state of the Dhcpv6 Client.
INT swL3IpCtrlIpDhcpOption12State	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.22	INTEGER	read-write	Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message.
STR swL3IpCtrlIpDhcpOption12HostName	1.3.6.1.4.1.171.11.117.1.5.3.2.1.3.1.23	DisplayString	read-write	Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12.
swL3Ipv6CtrlTable	1.3.6.1.4.1.171.11.117.1.5.3.2.1.4		not-accessible	This table contains IPv6 information of an IP interface.
swL3Ipv6CtrlEntry	1.3.6.1.4.1.171.11.117.1.5.3.2.1.4.1		not-accessible	A list of IPv6 information about a specific IP interface.
STR swL3Ipv6CtrlInterfaceName	1.3.6.1.4.1.171.11.117.1.5.3.2.1.4.1.1	DisplayString	read-only	This object indicates the name of the IP interface.
INT swL3Ipv6CtrlMaxReassmblySize	1.3.6.1.4.1.171.11.117.1.5.3.2.1.4.1.2	INTEGER	read-only	Maximum Reassembly Size of the IP interface.
U32 swL3Ipv6CtrlNsRetransTimer	1.3.6.1.4.1.171.11.117.1.5.3.2.1.4.1.3	Unsigned32	read-write	Neighbor solicitation's retransmit timer. The unit is set in milliseconds.
swL3Ipv6AddressCtrlTable	1.3.6.1.4.1.171.11.117.1.5.3.2.1.5		not-accessible	This table contain IPv6 address information for each IP interface.
swL3Ipv6AddressCtrlEntry	1.3.6.1.4.1.171.11.117.1.5.3.2.1.5.1		not-accessible	A list of information about a specific IPv6 address.
STR swL3Ipv6AddressCtrlInterfaceName	1.3.6.1.4.1.171.11.117.1.5.3.2.1.5.1.1	DisplayString	read-only	This object indicates the name of the IP interface.
ADR swL3Ipv6Address	1.3.6.1.4.1.171.11.117.1.5.3.2.1.5.1.2	Ipv6Address	read-only	Specify the IPv6 address.
INT swL3Ipv6AddressCtrlPrefixLen	1.3.6.1.4.1.171.11.117.1.5.3.2.1.5.1.3	INTEGER	read-only	Indicates the prefix length of this IPv6 address.
ROW swL3Ipv6AddressCtrlState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.5.1.8	RowStatus	read-create	This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
INT swL3Ipv6AddressCtrlAddressType	1.3.6.1.4.1.171.11.117.1.5.3.2.1.5.1.9	INTEGER	read-only	This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement.
INT swL3IpCtrlAllIpIfState	1.3.6.1.4.1.171.11.117.1.5.3.2.1.7	INTEGER	read-write	This object indicates all interface function state of the device.
swL3IpFdbMgmt	1.3.6.1.4.1.171.11.117.1.5.3.2.2
swL3IpFdbInfoTable	1.3.6.1.4.1.171.11.117.1.5.3.2.2.1		not-accessible	A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
swL3IpFdbInfoEntry	1.3.6.1.4.1.171.11.117.1.5.3.2.2.1.1		not-accessible	Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
IP swL3IpFdbInfoIpAddr	1.3.6.1.4.1.171.11.117.1.5.3.2.2.1.1.1	IpAddress	read-only	A IP address for which switch has forwarding and/or filtering information.
IP swL3IpFdbInfoIpSubnetMask	1.3.6.1.4.1.171.11.117.1.5.3.2.2.1.1.2	IpAddress	read-only	A IP net mask for this interface for which the switch has forwarding and/or filtering information.
INT swL3IpFdbInfoPort	1.3.6.1.4.1.171.11.117.1.5.3.2.2.1.1.3	INTEGER	read-only	Either the value '0', or the port number of the port on which packets having an IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address.
INT swL3IpFdbInfoType	1.3.6.1.4.1.171.11.117.1.5.3.2.2.1.1.4	INTEGER	read-only	The status of this entry.
INT swL3IpArpAgingTime	1.3.6.1.4.1.171.11.117.1.5.3.2.4	INTEGER	read-write	The timeout period in minutes for aging out dynamically learned arp information.
swL3IpStaticRouteTable	1.3.6.1.4.1.171.11.117.1.5.3.2.5		not-accessible	This entity's IP static Routing table.
swL3IpStaticRouteEntry	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1		not-accessible	A particular route to a particular destination, under a particular policy. Once an entry be built,it shouldn't be modified.That is,it just support create and delete action.
IP swL3IpStaticRouteDest	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.1	IpAddress	read-only	The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
IP swL3IpStaticRouteMask	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.2	IpAddress	read-only	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
INT swL3IpStaticRouteBkupState	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.3	INTEGER	read-create	The routing state for this route.The value SHOULD be primary(1) or backup(2).
IP swL3IpStaticRouteNextHop	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.4	IpAddress	read-only	On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0.
INT swL3IpStaticRouteMetric	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.5	INTEGER	read-create	The routing metric for this route.
INT swL3IpStaticRouteStatus	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.6	INTEGER	read-create	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. active(4) - the nextHop of this entry exists in the ARP table. inActive(5) - the next hop of this entry does not exist in the ARP table.
INT swL3IpStaticRouteWeight	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.7	INTEGER	read-create	Specifies the weight value. Used for the weighted multipath.
STR swL3IpStaticRouteInterfaceName	1.3.6.1.4.1.171.11.117.1.5.3.2.5.1.8	DisplayString	read-only	Specifies the name of the IP interface.

RFC description

D-Link DGS-3120-48PC switch vendor MIB for Layer 3 management including routing, IP configuration, and DHCP.

Start monitoring D-Link DGS-3120-48PC PoE switch (L3) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DGS-3120-48PC-L3MGMT-MIB

What Is DGS-3120-48PC-L3MGMT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description