All MIBs › CPQFCA-MIB › cpqFcaLogDrvPercentRebuild
cpqFcaLogDrvPercentRebuild
Module: CPQFCA-MIB
OID (symbolic): CPQFCA-MIB::cpqFcaLogDrvPercentRebuild
OID (numeric): 1.3.6.1.4.1.232.16.2.3.1.1.6
Node type: OBJECT-TYPE
Type: Gauge
Access: read-only
Description: Logical Drive Percent Rebuild.
After a failed physical drive has been replaced, the physical drive must have its data rebuilt. This value the percent complete of the rebuild. When the value reaches 100, the rebuilding process is complete. The drive array continues to operate in interim recovery mode while a drive is rebuilding.
When a logical volume is Expanding, the drive must redistribute the logical volume data across the physical drives. This value shows how many blocks of data still need to be redistributed. When the value reaches one hundred (100), the expand process is complete. The array continues to operate normally while the drive is expanding.
This value is only valid if the Logical Drive Status is rebuilding (7) or expanding (12).
If the value cannot be determined or a rebuild is not active, the value is set to 4,294,967,295.
What is cpqFcaLogDrvPercentRebuild?
This gauge shows the percent-complete progress of a physical drive rebuild operation on the logical drive, reaching 100 when the rebuild finishes. An admin watches this after replacing a failed disk to know how close the array is to full redundancy again, since the drive continues to run in interim recovery mode (with reduced fault tolerance) until rebuild completes. For instance, a stalled value of 42 that never advances over several polling cycles would indicate the rebuild has hung and needs investigation.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.232.16.2.3.1.1.6 snmpwalk -v2c -c public <target> CPQFCA-MIB::cpqFcaLogDrvPercentRebuild
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.232.16.2.3.1.1.6.1 snmpget -v2c -c public <target> CPQFCA-MIB::cpqFcaLogDrvPercentRebuild.1
Start monitoring Legacy Compaq Fibre Channel Array (CPQFCA) storage controller with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CPQFCA-MIB::cpqFcaLogDrvPercentRebuild OID value, configure state conditions and alerts, and monitor any Legacy Compaq Fibre Channel Array (CPQFCA) storage controller from a single console.
OID Breakdown
Upper-level ancestors (7 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.232 | compaq | COMPAQ-ID-REC-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.232.16 | cpqFibreArray | CPQFCA-MIB |
| 1.3.6.1.4.1.232.16.2 | cpqFcaComponent | CPQFCA-MIB |
| 1.3.6.1.4.1.232.16.2.3 | cpqFcaLogDrv | CPQFCA-MIB |
| 1.3.6.1.4.1.232.16.2.3.1 | cpqFcaLogDrvTable | CPQFCA-MIB |
| 1.3.6.1.4.1.232.16.2.3.1.1 | cpqFcaLogDrvEntry | CPQFCA-MIB |
| 1.3.6.1.4.1.232.16.2.3.1.1.6 | cpqFcaLogDrvPercentRebuild | CPQFCA-MIB |