All MIBs › CME-MIB › smCfgCtrlOnResetEnableDisable
smCfgCtrlOnResetEnableDisable
Module: CME-MIB
OID (symbolic): CME-MIB::smCfgCtrlOnResetEnableDisable
OID (numeric): 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: Switch module configuration control on resets (default and unsolicited). When set to enabled, the factory default IP configuration will become active when the I/O module is reset to factory defaults by either the management module or the I/O module. If an I/O module reset is initiated by a source other than the management module then the previous IP configuration will be in affect. In both these cases the MM will lose IP communications with the IOM. This MIB object can not be set, if MM grants switch module the Protected Mode permission and switch module goes into Protected Mode.
NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional (i.e. - 0 and 1 are swapped), however, they cannot be changed since this MIB is already published.
NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode. A value of disabled(1) will be returned.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9 snmpwalk -v2c -c public <target> CME-MIB::smCfgCtrlOnResetEnableDisable
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9.1 snmpget -v2c -c public <target> CME-MIB::smCfgCtrlOnResetEnableDisable.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9.1 i <value>
Start monitoring Cisco Communications Manager Express (CME) router/gateway with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CME-MIB::smCfgCtrlOnResetEnableDisable OID value, configure state conditions and alerts, and monitor any Cisco Communications Manager Express (CME) router/gateway from a single console.
OID Breakdown
Upper-level ancestors (15 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.2 | ibm | BLADE-MIB |
| 1.3.6.1.4.1.2.3 | ibmAgents | BLADE-MIB |
| 1.3.6.1.4.1.2.3.51 | netfinitySupportProcessorAgent | BLADE-MIB |
| 1.3.6.1.4.1.2.3.51.2 | bladeCenterSnmpMIB | BLADE-MIB |
| 1.3.6.1.4.1.2.3.51.2.22 | bladeCenter | BLADE-MIB |
| 1.3.6.1.4.1.2.3.51.2.22.3 | switchModule | BLADE-MIB |
| 1.3.6.1.4.1.2.3.51.2.22.3.1 | switchModuleControl | BLADE-MIB |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1 | smControlTable | BLADE-MIB |
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1 | smControlEntry | BLADE-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9 | smCfgCtrlOnResetEnableDisable | CME-MIB |