All MIBs › CISCO-WAN-AXIPOP-MIB › frConnServiceType
frConnServiceType
Module: CISCO-WAN-AXIPOP-MIB
OID (symbolic): CISCO-WAN-AXIPOP-MIB::frConnServiceType
OID (numeric): 1.3.6.1.4.1.351.110.5.1.2.1.1.1.43
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard ABR 7 ==> foresight ABR Note that this is used by PXM card, SV+ doesn't need to set it, if not set in the connection setup request, it'll be defaulted to ATFR type for FRSM. Also to make it compatible with existing AUSM MIB definition, value 3 is not used.
The following types are being added for PNNI support. and are based on UNI 4.0 cbr1 (21) - CBR.1 vbr1rt (22) - Real time VBR.1 vbr2rt (23) - Real time VBR.2 vbr3rt (24) - Real time VBR.3 vbr1nrt(25) - Non Real time VBR.1 vbr2nrt(26) - Non Real time VBR.2 vbr3nrt(27) - Non Real time VBR.3 ubr1 (28) - UBR.1 ubr2 (29) - UBR.2 stdabr (30) - TM 4.0 compliant standard ABR cbr2 (31) - CBR.2 cbr3 (32) - CBR.3
For FRSM12 Card: Not Supported. Derived from chanServType.
What is frConnServiceType?
This read-write enumeration specifies the ATM service category for the connection, including cbr(1, Constant Bit Rate), vbr(2, Variable Bit Rate), ubr(4, Unspecified Bit Rate), atfr(5, ATM frame relay), abrstd(6, standard ABR), abrfst(7, foresight ABR), and vbrrt(8), among others; the PXM uses this value, and if it is left unset on an FRSM card the connection defaults to ATFR type. An administrator sets frConnServiceType to select which ATM traffic contract and queuing behavior a connection receives when carried over the ATM backbone. For example, leaving frConnServiceType unset on an FRSM connection results in it defaulting to atfr(5) rather than to cbr or vbr, unless the administrator explicitly overrides it.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.351.110.5.1.2.1.1.1.43 snmpwalk -v2c -c public <target> CISCO-WAN-AXIPOP-MIB::frConnServiceType
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.351.110.5.1.2.1.1.1.43.1 snmpget -v2c -c public <target> CISCO-WAN-AXIPOP-MIB::frConnServiceType.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.351.110.5.1.2.1.1.1.43.1 i <value>
Start monitoring Cisco MGX 8000-series ATM WAN switches (AXIPOP processor, legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-WAN-AXIPOP-MIB::frConnServiceType OID value, configure state conditions and alerts, and monitor any Cisco MGX 8000-series ATM WAN switches (AXIPOP processor, legacy) from a single console.
OID Breakdown
Upper-level ancestors (11 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.351 | stratacom | CISCOWAN-SMI |
| 1.3.6.1.4.1.351.110 | basis | BASIS-MIB |
| 1.3.6.1.4.1.351.110.5 | basisServices | BASIS-MIB |
| 1.3.6.1.4.1.351.110.5.1 | frameRelay | BASIS-MIB |
| 1.3.6.1.4.1.351.110.5.1.2 | frChan | BASIS-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.351.110.5.1.2.1 | frChanCnfGrp | CISCO-WAN-AXIPOP-MIB |
| 1.3.6.1.4.1.351.110.5.1.2.1.1 | frChanCnfGrpTable | CISCO-WAN-AXIPOP-MIB |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1 | frChanCnfGrpEntry | CISCO-WAN-AXIPOP-MIB |
| 1.3.6.1.4.1.351.110.5.1.2.1.1.1.43 | frConnServiceType | CISCO-WAN-AXIPOP-MIB |