All MIBs › CISCO-VISM-DSX1-MIB › vismTrunkConditionEnable
vismTrunkConditionEnable
Module: CISCO-VISM-DSX1-MIB
OID (symbolic): CISCO-VISM-DSX1-MIB::vismTrunkConditionEnable
OID (numeric): 1.3.6.1.4.1.351.110.4.3.5.1.1.1.11
Node type: OBJECT-TYPE
Type: TruthValue
Access: read-write
Description: This object determines if trunk conditioning should be enabled or disabled on this line. If this object is set to true(1), VISM will do trunk conditioning on the affected DS0s on this line when it sees an alarm (AIS) on the ATM side, instead of sending AIS on the line side.
If there are endpoints or CCS channels enabled on a line then setting of this object is not allowed.
Trunk conditioning: VISM will transmit idle code pattern for the first 2.5 secs and then will transmit seized code which is configured in ds0IdleCode and ds0SeizedCode respectively, ds0IdleCode and ds0SeizedCode from CISCO-VISM-DSX0-MIB.
This object is applicable only in trunking application.
This object can be set in all applications but will be applicable in trunking application only.
What is vismTrunkConditionEnable?
This read-write TruthValue determines whether trunk conditioning is enabled on this line, meaning VISM performs conditioning on affected DS0s in response to an ATM-side AIS alarm instead of sending AIS on the line side, and it cannot be set if endpoints or CCS channels are enabled on the line. Trunk conditioning masks upstream ATM problems from downstream TDM equipment by substituting a defined signaling pattern rather than propagating the alarm, which an admin uses to prevent cascading failures into the PBX side. For example, on a line dedicated to raw TDM trunking with no signaling endpoints, an admin would enable vismTrunkConditionEnable so a transient ATM fault doesn't immediately trip alarms on the connected PBX.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.351.110.4.3.5.1.1.1.11 snmpwalk -v2c -c public <target> CISCO-VISM-DSX1-MIB::vismTrunkConditionEnable
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.351.110.4.3.5.1.1.1.11.1 snmpget -v2c -c public <target> CISCO-VISM-DSX1-MIB::vismTrunkConditionEnable.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.351.110.4.3.5.1.1.1.11.1 s <value>
Start monitoring Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-VISM-DSX1-MIB::vismTrunkConditionEnable OID value, configure state conditions and alerts, and monitor any Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) from a single console.
OID Breakdown
Upper-level ancestors (10 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.351 | stratacom | CISCOWAN-SMI |
| 1.3.6.1.4.1.351.110 | basis | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4 | basisLines | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4.3 | dsx1 | BASIS-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.351.110.4.3.5 | dsx1Vism | CISCO-VISM-DSX1-MIB |
| 1.3.6.1.4.1.351.110.4.3.5.1 | dsx1VismCnfGrp | CISCO-VISM-DSX1-MIB |
| 1.3.6.1.4.1.351.110.4.3.5.1.1 | dsx1VismCnfGrpTable | CISCO-VISM-DSX1-MIB |
| 1.3.6.1.4.1.351.110.4.3.5.1.1.1 | dsx1VismCnfGrpEntry | CISCO-VISM-DSX1-MIB |
| 1.3.6.1.4.1.351.110.4.3.5.1.1.1.11 | vismTrunkConditionEnable | CISCO-VISM-DSX1-MIB |