| OID symbolic | OID numeric | Type | Access | Description |
|---|
| org | 1.3 | | | |
| dod | 1.3.6 | | | |
| internet | 1.3.6.1 | | | |
| private | 1.3.6.1.4 | | | |
| enterprises | 1.3.6.1.4.1 | | | |
| bintec | 1.3.6.1.4.1.272 | | | |
| bibo | 1.3.6.1.4.1.272.4 | | | |
| mdm | 1.3.6.1.4.1.272.4.18 | | | |
| mdmProfileTable | 1.3.6.1.4.1.272.4.18.1 | | not-accessible | This Table contains entries for the modem profiles. For
PPP connections, modem profiles are assigned to incoming
connections via the isdnDispatchtable. For outgoing
connections, the profile is assigned by the biboPppTable.
Profile 1 is used as default profile for ppp and is the
only profile available for isdnlogin connections. |
| mdmProfileEntry | 1.3.6.1.4.1.272.4.18.1.1 | | not-accessible | |
| INT mdmProfileName | 1.3.6.1.4.1.272.4.18.1.1.1 | INTEGER | read-only | The name of the profile. Eight profiles are available. |
| STR mdmProfileDescr | 1.3.6.1.4.1.272.4.18.1.1.2 | DisplayString | read-write | Profile Description. Info only. |
| INT mdmProfileModulation | 1.3.6.1.4.1.272.4.18.1.1.3 | INTEGER | read-write | This object specifies the preferred modulation (automode on)
or the modulation (automode disabled) to be used in originating
or answering a connection.
bell103 (1) : 300
bell212 (2) : 1200
v21 (3) : 300
v22 (4) : 1200
v22bis (5) : 2400 or 1200
v23 (6) : 75/1200 or 1200/75
v32 (7) : 9600, 4800
v32bis (8) : 14000, 12000, 9600, 7200, 4800
v34 (9) : 33600, 31200, 28800, 26400, 24000, 21600, 19200,
16800, 14400, 12000, 9600, 7200, 4800, 2400
k56flex (10) : 56000, 54000, 52000, 50000, 48000, 46000,
44000, 42000, 40000, 38000, 36000, 34000, 32000
vfc (11) : 28800, 26400, 24000, 21600, 19200, 16800, 14400,
12000, 9600
v90 (12) : 56000, 54667, 53333, 52000, 50667, 49333, 48000, 46667,
45333, 42667, 41333, 40000, 38667, 37333, 36000, 34667,
33333, 32000, 30667, 29333, 28000 |
| INT mdmProfileMinBps | 1.3.6.1.4.1.272.4.18.1.1.4 | INTEGER | read-write | This object specified the lowest rate, at which the modem may
establish a connection. |
| INT mdmProfileMaxRecvBps | 1.3.6.1.4.1.272.4.18.1.1.5 | INTEGER | read-write | This object specifies the highest receive rate, at which the
modem may establsh a connection. |
| INT mdmProfileMaxXmitBps | 1.3.6.1.4.1.272.4.18.1.1.6 | INTEGER | read-write | This object specifies the highest transmit rate, at which the
modem may establsh a connection. |
| INT mdmProfileAutoMode | 1.3.6.1.4.1.272.4.18.1.1.7 | INTEGER | read-write | When this object is set to on, the modem will automatically
negotiate the best rates beginning with the selected
Modulation and MaxBps values. Otherwise, it will use only
the selected modulation in the range between MinBps and
MaxBps. |
| INT mdmProfileComprV42bis | 1.3.6.1.4.1.272.4.18.1.1.8 | INTEGER | read-write | This object specifies, whether V.42bis compression
shall be used for modem connections. When set to off,
V.42bis compression will never be used. When set to auto,
compression may be negotiated with the partner modem. |
| INT mdmProfileComprMNP5 | 1.3.6.1.4.1.272.4.18.1.1.9 | INTEGER | read-write | This object specifies, whether MNP Class 5 compression
shall be used for modem connections. When set to off,
MNP Class 5 compression will never be used. When set to auto,
compression may be negotiated with the partner modem. |
| INT mdmProfileErrorCorr | 1.3.6.1.4.1.272.4.18.1.1.10 | INTEGER | read-write | This object specifies the kind of error correction being
used for a connection:
none no error correction will be used.
required either LAPM or MNP will be used.
If the partner is not able to
do error correction, the connection
cannot be established.
auto negotiation takes place to
use either LAPM, MNP or no
error correction.
lapm Enforce LAPM error correction.
If the partner is not able to
do LAPM, the connection
cannot be established.
mnp use MNP error connection
If the partner is not able to
do MNP, the connection
cannot be established. |
| INT mdmProfileXmitLevel | 1.3.6.1.4.1.272.4.18.1.1.11 | INTEGER | read-write | This object specifies the transmit attenuation in dB. |
| INT mdmProfileCDWaitTime | 1.3.6.1.4.1.272.4.18.1.1.12 | INTEGER | read-write | This object specifies the amount of time in milliseconds,
the modem will wait for the appearance of the carrier. If
the carrier will not appear in this time period, the
connection will be disconnected. |
| INT mdmProfileCDRespTime | 1.3.6.1.4.1.272.4.18.1.1.13 | INTEGER | read-write | This object specifies the period of time in milliseconds,
a carrier has to be present, before it will be recognized
as a carrier. |
| INT mdmProfileCDDiscTime | 1.3.6.1.4.1.272.4.18.1.1.14 | INTEGER | read-write | This object specifies the amount of time, the carrier has to
drop, before the modem will assume the carrier to be lost. |
| INT mdmProfileRetrain | 1.3.6.1.4.1.272.4.18.1.1.15 | INTEGER | read-write | The modem will :
off (1) : disable line quality monitor and auto-retrain.
retrain (2) : enable line quality monitor and auto-retrain.
fallbf (3) : enable line quality monitor and fallback/fall forward. |
| INT mdmProfileIdleTimerMode | 1.3.6.1.4.1.272.4.18.1.1.16 | INTEGER | read-write | The idle timer is used to specify the duration of an interval between
successive characters received from the modem which, when exceeded,
will cause the modem driver to terminate the assembly of a data packet
and to forward it to the higher-layer protocols (this is in analogy to
the ITU X.3 parameter #4). This object specifies the mode how the idle
timer is set:
static (1): the idle time is taken from the object
mdmProfileIdleTimerFixedDelay (default)
dynamic (2): the idle time is set to the duration that a number of
mdmProfileIdleTimerCharDelay characters (octets) would
take for transmission corresponding to the actually
used receive bit-rate of the modem. If the bit-rate can
not be found out, the static mode is used instead. |
| INT mdmProfileIdleTimerFixedDelay | 1.3.6.1.4.1.272.4.18.1.1.17 | INTEGER | read-write | This object specifies the duration of the idle timer in milliseconds
(see the object mdmProfileIdleTimerMode for further description).
Default: 5 |
| INT mdmProfileIdleTimerCharDelay | 1.3.6.1.4.1.272.4.18.1.1.18 | INTEGER | read-write | This object specifies the number of characters (octets) which is used
to calculate the idle timer corresponding to the actually used receive
bit-rate of the modem (see the object mdmProfileIdleTimerMode for further
description). Default: 3 |
| mdmTable | 1.3.6.1.4.1.272.4.18.2 | | not-accessible | The mdmTable contains information for each modem. The entries
contain various statistical data for modem connections. Only the
system can add entries to this table. The user is able to reboot,
enable or disable a modem. The system updates infos about the
current connection. |
| mdmEntry | 1.3.6.1.4.1.272.4.18.2.1 | | not-accessible | |
| INT mdmIndex | 1.3.6.1.4.1.272.4.18.2.1.1 | INTEGER | read-only | Index of this modem (Slot/Cpu/Modem) |
| INT mdmAction | 1.3.6.1.4.1.272.4.18.2.1.2 | INTEGER | read-write | Writing to this variable
reboot (1) : initiates a reboot.
disabled (2) : remove modem resource from allocation pool.
enabled (3) : put modem to allocation resource pool. |
| INT mdmType | 1.3.6.1.4.1.272.4.18.2.1.3 | INTEGER | read-only | Type of this modem
csm56K (1) : CentralSiteModem K56Flex
csm336 (2) : CentralSiteModem 33600
mdm144 (3) : ClientSiteModem 14400
mdm336 (4) : ClientSiteModem 33600
telindus (5) : ADSP with Telindus firmware |
| INT mdmState | 1.3.6.1.4.1.272.4.18.2.1.4 | INTEGER | read-only | Current status of the modem.
booting (1) : init phase
idle (2) : this modem resource is available
calling (3) : outgoing call initiated
called (4) : incoming call initiated
connected (5) : data transfer phase established
hangup (6) : going to terminate a connection
stopped (7) : out of order, modem ist not useable |
| INT mdmMode | 1.3.6.1.4.1.272.4.18.2.1.5 | INTEGER | read-only | Type of mode
modem (1) : modem native
ppp (2) : modem native + async hdlc
fax (3) : fax mode
dtmf (4) : receive and signal DTMF touchtones
none (7) : modem curently not used |
| INT mdmModulation | 1.3.6.1.4.1.272.4.18.2.1.6 | INTEGER | read-only | Negotiated modulation. same as mdmProfileModulation. |
| INT mdmErrorCorr | 1.3.6.1.4.1.272.4.18.2.1.7 | INTEGER | read-only | Negotiated error correction protocol.
none (1) : no error correction
alt (2) : MNP error correction established
lapm (3) : LAPM error correction established |
| INT mdmCompression | 1.3.6.1.4.1.272.4.18.2.1.8 | INTEGER | read-only | Negotiated compression correction protocol.
none (1) : no compression
class5 (2) : MNP5 compression
v42bis (3) : V.42bis compression |
| INT mdmXmitSpeed | 1.3.6.1.4.1.272.4.18.2.1.9 | INTEGER | read-only | Negotiated transmit speed. |
| INT mdmRcvSpeed | 1.3.6.1.4.1.272.4.18.2.1.10 | INTEGER | read-only | Negotiated receive speed. |
| INT mdmIfIndex | 1.3.6.1.4.1.272.4.18.2.1.11 | INTEGER | read-only | the (ISDN) interface's slot this modem is connected to |
| INT mdmIfBchannel | 1.3.6.1.4.1.272.4.18.2.1.12 | INTEGER | read-only | the (ISDN) interface's B channel this modem is connected to |
