All MIBs › ARTEL-MIB
Category: Device Management
Description: Artel Video Systems SDI video-over-IP/fiber transmission equipment configuration and status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ARTEL-MIB?
This is an Artel Video Systems enterprise MIB for managing SDI (Serial Digital Interface) video-over-IP or video-over-fiber transmission equipment used in broadcast and production environments. Although the module description and sample objects were not captured, devices in this category, fiber/IP video transport gateways, typically expose signal presence/status, input/output port configuration, and transmission link health as their core management data. Its monitoring value would center on hardware and signal status, confirming SDI signal lock/presence on each port, link/fiber connectivity status, and equipment health such as power supply or alarm state, to ensure uninterrupted video transport. As a specialized broadcast-transport MIB it likely has minimal dependency on general-purpose IETF MIBs beyond basic SNMP framework conventions. It's typically deployed in broadcast facility racks and remote production environments where Artel fiber/IP video transport units link cameras, studios, or venues to a production control room. Network engineers evaluating or troubleshooting this functionality can download the ARTEL-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ARTEL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Artel Video Systems SDI video-over-fiber/IP transport equipment
Monitoring Examples
A broadcast engineer would poll the Artel unit's per-port signal status to confirm SDI lock is present on each input, and check link/fiber status objects to verify the transport path between two sites is up. Loss of signal-lock on a specific port during a live event would immediately flag a camera or fiber-run problem needing on-site attention. No sample object names were available for this module to cite directly.
What Can Be Monitored
- SDI signal presence/lock per port
- fiber/IP link status
- input/output port configuration
- equipment alarm/health status
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| Opaque | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| arcnet | 1.3.6.1.4.1.139.2.2 | |||
| INT arcnetBoardsPresent | 1.3.6.1.4.1.139.2.2.1 | INTEGER | read-only | A 17 bit bit-significant register returned as an integer. If the bit is set there is a board in that slot. The least significant bit represents slot 0. The most significant bit represents the System Management board. |
| CTR arcnetMyReconfigCounts | 1.3.6.1.4.1.139.2.2.5 | Counter | read-only | The number of times the internal Arcnet bus has been reconfigured by this board. |
| CTR arcnetNakCnts | 1.3.6.1.4.1.139.2.2.4 | Counter | read-only | The number of Negative Acknowledgements received by this board over the internal Arcnet interface when attemting to transmit. |
| CTR arcnetReconfigCounts | 1.3.6.1.4.1.139.2.2.6 | Counter | read-only | The total number of times the internal Arcnet bus has been reconfigured since powerup. |
| CTR arcnetRxPkts | 1.3.6.1.4.1.139.2.2.2 | Counter | read-only | The total number of packets received by this board over the internal Arcnet interface. |
| CTR arcnetTrashedRxMsgs | 1.3.6.1.4.1.139.2.2.7 | Counter | read-only | The number of Arcnet receive messages that were discarded by this board. |
| CTR arcnetTrashedTxMsgs | 1.3.6.1.4.1.139.2.2.8 | Counter | read-only | The number of Arcnet transmit messages that were discarded by this board. |
| CTR arcnetTxPkts | 1.3.6.1.4.1.139.2.2.3 | Counter | read-only | The total number of packets transmitted by this board over the internal Arcnet interface. |
| artel | 1.3.6.1.4.1.139 | |||
| artelTrap | 1.3.6.1.4.1.139.64 | |||
| OCT artelTrapAddrCommunity | 1.3.6.1.4.1.139.64.1.1.4 | OCTET STRING | read-write | The community name expected by the management station receiving traps. |
| artelTrapAddrEntry | 1.3.6.1.4.1.139.64.1.1 | not-accessible | Information needed to deliver traps to a particular management station. | |
| IP artelTrapAddrIpDest | 1.3.6.1.4.1.139.64.1.1.1 | IpAddress | read-write | The IP address of the management agent receiving traps. |
| INT artelTrapAddrStatus | 1.3.6.1.4.1.139.64.1.1.5 | INTEGER | read-write | Permanent entries will be kept in non-volatile ram until the user specifically invalidates the entry. Temporary entries will be timed out after a minimum 10 minute interval. Invalid entries will be removed from the table. |
| artelTrapAddrTable | 1.3.6.1.4.1.139.64.1 | not-accessible | A table of management systems ready to accept traps generated by this node. | |
| INT artelTrapAddrUdpDest | 1.3.6.1.4.1.139.64.1.1.3 | INTEGER | read-write | The UDP port number used by the management station to receive traps. |
| OCT artelTrapAddrXPortIndex | 1.3.6.1.4.1.139.64.1.1.2 | OCTET STRING | read-only | This is the UDP address defined as an OCTET STRING of 2 bytes for the purpose of using it as an instance whoses sub-id lengths cannot exceed one byte in length. |
| STR artelTrapReportString | 1.3.6.1.4.1.139.64.2 | DisplayString | read-only | When read this will always return a NULL string. It will be returned in varBindList of Artel proprietary traps to provide the user with any additional information available to the agent. |
| backplane | 1.3.6.1.4.1.139.2.3 | |||
| board | 1.3.6.1.4.1.139.2.1 | |||
| INT boardClass | 1.3.6.1.4.1.139.2.1.7 | INTEGER | read-only | The type of board/device. |
| IP boardIpAddr | 1.3.6.1.4.1.139.2.1.1 | IpAddress | read-write | The administratively assigned IP Address for this board. |
| INT boardLedStatus | 1.3.6.1.4.1.139.2.1.5 | INTEGER | read-only | The returns 16 bits encoded as an integer that represent the LEDs found on the front panel of the System Management board and on internal LED displays on the Starbridge Board. The most significant bit represents the leftmost LED. PLEASE NOTE: If the bit is 1 it indicates that the LED is OFF. If the bit is 0 it indicates that the LED is ON. |
| INT boardReset | 1.3.6.1.4.1.139.2.1.3 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the board to reset. |
| CTR boardResetCounts | 1.3.6.1.4.1.139.2.1.8 | Counter | read-only | The number of times the 68K processor on this board has reset since the last time the non-volatile ram has been reset to default values. |
| INT boardResetNvRam | 1.3.6.1.4.1.139.2.1.4 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the non-volatile ram to be reset to their default values. |
| INT boardSlotNum | 1.3.6.1.4.1.139.2.1.6 | INTEGER | read-only | The Galactica Chassis slot that this board resides in. The slots are numbered 0 thru n with 0 being the bottom slot. |
| STR boardSnmpMibVersion | 1.3.6.1.4.1.139.2.1.9 | DisplayString | read-only | The version of the Artel Proprietary MIB supported by this board. |
| INT bpStatsEnabled | 1.3.6.1.4.1.139.2.3.1 | INTEGER | read-write | The administrative state of this boards connection to the Galactica 1 gigabit GBus. |
| INT bpStatsInitialize | 1.3.6.1.4.1.139.2.3.7 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the Backplane statistics to be cleared. |
| INT bpStatsOperState | 1.3.6.1.4.1.139.2.3.6 | INTEGER | read-only | Operational state of this boards connection to the Galactica 1 gigabit GBus. |
| bpStatsRxBusyTable | 1.3.6.1.4.1.139.2.3.9 | not-accessible | A table stored on each board (except System Managers) that counts the number of packets transmitted by this board across the backplane that had to be discarded because the receiving board was too busy. | |
| bpStatsRxBusyTableEntry | 1.3.6.1.4.1.139.2.3.9.1 | not-accessible | An entry for another board in the node that counts the number of backplane packets from this board that the other board was too busy to receive. | |
| CTR bpStatsRxBusyTableErrors | 1.3.6.1.4.1.139.2.3.9.1.2 | Counter | read-only | A count of the number of backplane packets transmitted by this board to the board in slot bpStatsRxBusyTableIndex that the other board was too busy to receive. |
| INT bpStatsRxBusyTableIndex | 1.3.6.1.4.1.139.2.3.9.1.1 | INTEGER | read-only | The slot number of the receiving board. |
| CTR bpStatsRxErrors | 1.3.6.1.4.1.139.2.3.3 | Counter | read-only | Number of received packets that were received from the Galactica 1 gigabit GBus that contained errors. |
| CTR bpStatsRxPkts | 1.3.6.1.4.1.139.2.3.2 | Counter | read-only | Total number of packets received by this board from the Galactica 1 gigabit GBus. |
| CTR bpStatsTxErrors | 1.3.6.1.4.1.139.2.3.5 | Counter | read-only | Number of packets which could not be transmitted because the receiver board was busy. |
| CTR bpStatsTxPkts | 1.3.6.1.4.1.139.2.3.4 | Counter | read-only | Total number of packets transmitted by this board from the Galactica 1 gigabit GBus. |
| CTR bpStatsTxQOverErrors | 1.3.6.1.4.1.139.2.3.8 | Counter | read-only | A count of the number of overflows of the backplane transmit queue. |
| bridge | 1.3.6.1.4.1.139.2.4 | |||
| OPA bridgeAddrFilterBlockData | 1.3.6.1.4.1.139.2.4.17.1.2 | Opaque | read-only | There will be 100 address entries returned. Each address entry contains the following data: ENTRY NUMBER: 2 octets - The physical entry into the node's address filtering database for this address. MAC ADDRESS: 6 octets - The MAC address for this entry. ENTRY TYPE: 1 octet - The type of entry can be one of the following: invalid(1) : this entry is not valid. learned(2) : the value of the PORT and SLOT was learned, and is being used. static(3) : the address is in the dot1dStaticTable with the instance of the MAC address. restrict(4) : the address is in the restrictedTable with the instance of the MAC address. spantree(5) : the address is the spanning tree group address. self(6) : The address is one of the bridge's addresses. The SLOT indicates which of the node's boards has this address. SLOT: 1 octet - If 'learned' the slot number of the board on which a frame having a source address equal to the value of the MAC address has been seen. If 'self' the slot number of the board with that MAC address. Else a value of '0' indicating that the bridge does have some forwarding/filtering information about this MAC address (e.g. in the dot1dStaticTable). PORT: 1 octet - If 'learned' the port number of the port on which a frame having a source address equal to the value of the MAC address has been seen. Else a value of '0' indicating that the bridge does have some forwarding/ filtering information about this MAC address (e.g. in the dot1dStaticTable). AGE: 1 octet - If 'learned' the value of the AGE flag: invalid(1) : not valid for this entry. notaged(2) : the MAC address has not been aged. onceaged(3) : The MAC address has been aged once. It will be removed from the database the next time the aging process executes unless a packet with the MAC address in the source address field is received. |
| INT bridgeAddrFilterBlockIndex | 1.3.6.1.4.1.139.2.4.17.1.1 | INTEGER | read-only | Block number for this entry. Each block holds information on 100 entry locations into the node's address filtering database. |
| bridgeAddrFilterEntry | 1.3.6.1.4.1.139.2.4.17.1 | not-accessible | Address filtering information maintained on a block of 100 entries in the node's filtering database. | |
| bridgeAddrFilterTable | 1.3.6.1.4.1.139.2.4.17 | not-accessible | A table that contains information about MAC addresses for which the node has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. | |
| INT bridgeAgeNow | 1.3.6.1.4.1.139.2.4.2 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the forwarding database to be fully aged. |
| INT bridgeDot1dEnable | 1.3.6.1.4.1.139.2.4.3 | INTEGER | read-write | Enables and disables the IEE 802.1d Spanning Tree Protocol for the board. |
| INT bridgeDot1dResetDefaults | 1.3.6.1.4.1.139.2.4.4 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the Spanning Tree objects to be reset to the default values. |
| PHY bridgedot1dTpFdbAddress | 1.3.6.1.4.1.139.2.4.18.1.1 | PhysAddress | read-only | A MAC address for which the bridge has some forwarding and/or filtering information. Same as dot1dTpFdbAddress. |
| INT bridgedot1dTpFdbAge | 1.3.6.1.4.1.139.2.4.18.1.5 | INTEGER | read-only | If the bridgedot1dTpFdbStatus is 'learned' then the value of the AGE flag is: invalid(1) : Not valid for this entry. notaged(2) : The MAC address has not been aged. onceaged(3) : The MAC address has been aged once. It will be removed from the database the next time the aging process executes unless a packet with the MAC address in the source address field is received. |
| bridgedot1dTpFdbEntry | 1.3.6.1.4.1.139.2.4.18.1 | not-accessible | Information about a specific MAC address for which the bridge has some forwarding and/or filtering information. | |
| INT bridgedot1dTpFdbPort | 1.3.6.1.4.1.139.2.4.18.1.3 | INTEGER | read-only | If bridgeDot1dTpFdbStatus is 'learned' then the port number of the port on which a frame having a source address equal to the value of the MAC address has been seen. Else a value of '0' indicating that the bridge does have some forwarding/filtering information about this MAC address (e.g. in the dot1dStaticTable). |
| INT bridgedot1dTpFdbSlot | 1.3.6.1.4.1.139.2.4.18.1.2 | INTEGER | read-only | If bridgeDot1dTpFdbStatus is 'learned' then the slot number of the board on which a frame having a source address equal to the value of the MAC address has been seen. If 'self' the slot number of the board with that MAC address. Else a value of '0' indicating that the bridge does have some forwarding/filtering information about this MAC address (e.g. in the dot1dStaticTable). |
| INT bridgedot1dTpFdbStatus | 1.3.6.1.4.1.139.2.4.18.1.4 | INTEGER | read-only | The type of entry can be one of the following: invalid(1) : This entry is not valid. learned(2) : The value of the PORT and SLOT was learned, and is being used. static(3) : The address is in the dot1dStaticTable with the instance of the MAC address. restrict(4) : The address is in the restrictedTable with the instance of the MAC address. spantree(5) : The address is the spanning tree group address. self(6) : The address is one of the bridge's addresses. The port indicates which of the node's boards has this address. |
| bridgedot1dTpFdbTable | 1.3.6.1.4.1.139.2.4.18 | not-accessible | A table that contains information about MAC addresses for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. This table is an extension of the dot1dTpFdbTable. | |
| TIK bridgePktSwLastReset | 1.3.6.1.4.1.139.2.4.7 | TimeTicks | read-only | The value of sysUpTime when the packet swtiching function was last reset. |
| INT bridgePortGroupEnable | 1.3.6.1.4.1.139.2.4.13 | INTEGER | read-write | Enables and disables all Port Group filtering for the node. |
| bridgePortGroupEntry | 1.3.6.1.4.1.139.2.4.14.1 | not-accessible | Port group information maintained on a single port and group. | |
| STR bridgePortGroupGroupComment | 1.3.6.1.4.1.139.2.4.16.1.3 | DisplayString | read-only | A readable string that contains all of the port groups that this port is a member of. |
| bridgePortGroupGroupEntry | 1.3.6.1.4.1.139.2.4.16.1 | not-accessible | Port group information maintained on a single port group. | |
| INT bridgePortGroupGroupIndex | 1.3.6.1.4.1.139.2.4.16.1.1 | INTEGER | read-only | The group number on the node. |
| OCT bridgePortGroupGroupPortMap | 1.3.6.1.4.1.139.2.4.16.1.2 | OCTET STRING | read-write | The set of ports which are members of this group. Packets can only be forwarded to ports in the same port group(s) as the port on which the packet was received. A port can be in multiple port groups. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8 on board 1, the second octet specifying ports 1 through 8 on board 2, etc. Within each octet the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| bridgePortGroupGroupTable | 1.3.6.1.4.1.139.2.4.16 | not-accessible | A table maintaining the port group information for each group on the node. | |
| STR bridgePortGroupPortDisplayString | 1.3.6.1.4.1.139.2.4.15.1.2 | DisplayString | read-only | A readable string that contains all of the port groups that this port is a member of. |
| bridgePortGroupPortEntry | 1.3.6.1.4.1.139.2.4.15.1 | not-accessible | Port group information maintained on a single port. | |
| INT bridgePortGroupPortIndex | 1.3.6.1.4.1.139.2.4.15.1.1 | INTEGER | read-only | The port number on the board. Same as ifIndex. |
| bridgePortGroupPortTable | 1.3.6.1.4.1.139.2.4.15 | not-accessible | A table containing the port group information as readable strings on each port on the board. | |
| bridgePortGroupTable | 1.3.6.1.4.1.139.2.4.14 | not-accessible | A table containing the port group information on each port and group in the node. | |
| INT bridgePortGroupTableEnable | 1.3.6.1.4.1.139.2.4.14.1.3 | INTEGER | read-write | This object indicates the status of this entry. enable(1) - This port is currently contained in this group. disable(2) - This port is not currently contained in this group. |
| INT bridgePortGroupTableGroupIndex | 1.3.6.1.4.1.139.2.4.14.1.2 | INTEGER | read-only | The group number in the node. |
| INT bridgePortGroupTablePortIndex | 1.3.6.1.4.1.139.2.4.14.1.1 | INTEGER | read-only | The port number in the node. |
| INT bridgeResetPktSwCount | 1.3.6.1.4.1.139.2.4.6 | INTEGER | read-only | A count of the number of times the packet switching function has been reset. |
| INT bridgeResetStatic | 1.3.6.1.4.1.139.2.4.8 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the static table to be cleared. |
| INT bridgeRestrictedReset | 1.3.6.1.4.1.139.2.4.9 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the restricted table to be cleared. |
| PHY bridgeUdfAddressMask | 1.3.6.1.4.1.139.2.4.11.1.9 | PhysAddress | read-write | The value used to mask off the data value used for comparison on the MAC address in the packet. Don't care bits are zero. |
| INT bridgeUdfAddressOperand | 1.3.6.1.4.1.139.2.4.11.1.10 | INTEGER | read-write | The operand used in the comparison of the bridgeUdfAddressValue and the MAC address in the packet. |
| INT bridgeUdfAddressType | 1.3.6.1.4.1.139.2.4.11.1.7 | INTEGER | read-write | Source indicates that the address portion of this filter is using the source MAC address. Destination indicates the address portion of this filter is using the destination MAC address. |
| PHY bridgeUdfAddressValue | 1.3.6.1.4.1.139.2.4.11.1.8 | PhysAddress | read-write | The data value used for comparison on the MAC address in the packet. |
| STR bridgeUdfComment | 1.3.6.1.4.1.139.2.4.11.1.4 | DisplayString | read-write | A comment field to describe this filter. |
| INT bridgeUdfCountInitMatchCount | 1.3.6.1.4.1.139.2.4.12.1.2 | INTEGER | read-write | When read this object always returns 1. When set to any value it will clear all of the bridgeUdfMatchCounts objects for this port. |
| INT bridgeUdfCountPortIndex | 1.3.6.1.4.1.139.2.4.12.1.1 | INTEGER | read-only | The port number on the board. Same as ifIndex. |
| bridgeUdfEntry | 1.3.6.1.4.1.139.2.4.11.1 | not-accessible | User defined filtering information maintained on a single port and filter. | |
| INT bridgeUdfFilterIndex | 1.3.6.1.4.1.139.2.4.11.1.2 | INTEGER | read-only | The filter number for the port. |
| bridgeUdfInitCountEntry | 1.3.6.1.4.1.139.2.4.12.1 | not-accessible | A table entry used to clear all of a port's bridgeUdfMatchCounts. | |
| bridgeUdfInitCountTable | 1.3.6.1.4.1.139.2.4.12 | not-accessible | A table used to clear all of a port's bridgeUdfMatchCounts. | |
| INT bridgeUdfInitMatchCount | 1.3.6.1.4.1.139.2.4.11.1.6 | INTEGER | read-write | When read this object always returns 1. When set to any value it will clear the bridgeUdfMatchCounts object for this port and filter. |
| CTR bridgeUdfMatchCounts | 1.3.6.1.4.1.139.2.4.11.1.5 | Counter | read-only | The number of packets that matched this filter when the bridgeUdfState was either filter, forward or count. |
| INT bridgeUdfOffset1Mask | 1.3.6.1.4.1.139.2.4.11.1.16 | INTEGER | read-write | The value used to mask off the data value used for comparison on the offset1 field in the packet. Don't care bits are zero. |
| INT bridgeUdfOffset1Offset | 1.3.6.1.4.1.139.2.4.11.1.14 | INTEGER | read-write | The number of bytes from the start of the MAC header to the start of the data area in the packet to be used in the filter's comparison. This value must be divisible by 4. |
| INT bridgeUdfOffset1Operand | 1.3.6.1.4.1.139.2.4.11.1.17 | INTEGER | read-write | The operand used in the comparison of the bridgeUdfOffset1Value and the type field in the packet. |
| INT bridgeUdfOffset1Value | 1.3.6.1.4.1.139.2.4.11.1.15 | INTEGER | read-write | The data value used for comparison on the offset1 field as specified by bridgeUdfOffset1Offset in the packet. |
| INT bridgeUdfOffset2Mask | 1.3.6.1.4.1.139.2.4.11.1.20 | INTEGER | read-write | The value used to mask off the data value used for comparison on the offset2 field in the packet. Don't care bits are zero. |
| INT bridgeUdfOffset2Offset | 1.3.6.1.4.1.139.2.4.11.1.18 | INTEGER | read-write | The number of bytes from the start of the MAC header to the start of the data area in the packet to be used in the filter's comparison. This value must be divisible by 4. |
| INT bridgeUdfOffset2Operand | 1.3.6.1.4.1.139.2.4.11.1.21 | INTEGER | read-write | The operand used in the comparison of the bridgeUdfOffset2Value and the type field in the packet. |
| INT bridgeUdfOffset2Value | 1.3.6.1.4.1.139.2.4.11.1.19 | INTEGER | read-write | The data value used for comparison on the offset1 field as specified by bridgeUdfOffset2Offset in the packet. |
| INT bridgeUdfOffset3Mask | 1.3.6.1.4.1.139.2.4.11.1.24 | INTEGER | read-write | The value used to mask off the data value used for comparison on the offset3 field in the packet. Don't care bits are zero. |
| INT bridgeUdfOffset3Offset | 1.3.6.1.4.1.139.2.4.11.1.22 | INTEGER | read-write | The number of bytes from the start of the MAC header to the start of the data area in the packet to be used in the filter's comparison. This value must be divisible by 4. |
| INT bridgeUdfOffset3Operand | 1.3.6.1.4.1.139.2.4.11.1.25 | INTEGER | read-write | The operand used in the comparison of the bridgeUdfOffset3Value and the type field in the packet. |
| INT bridgeUdfOffset3Value | 1.3.6.1.4.1.139.2.4.11.1.23 | INTEGER | read-write | The data value used for comparison on the offset1 field as specified by bridgeUdfOffset3Offset in the packet. |
| INT bridgeUdfOffset4Mask | 1.3.6.1.4.1.139.2.4.11.1.28 | INTEGER | read-write | The value used to mask off the data value used for comparison on the offset4 field in the packet. Don't care bits are zero. |
| INT bridgeUdfOffset4Offset | 1.3.6.1.4.1.139.2.4.11.1.26 | INTEGER | read-write | The number of bytes from the start of the MAC header to the start of the data area in the packet to be used in the filter's comparison. This value must be divisible by 4. |
| INT bridgeUdfOffset4Operand | 1.3.6.1.4.1.139.2.4.11.1.29 | INTEGER | read-write | The operand used in the comparison of the bridgeUdfOffset4Value and the type field in the packet. |
| INT bridgeUdfOffset4Value | 1.3.6.1.4.1.139.2.4.11.1.27 | INTEGER | read-write | The data value used for comparison on the offset1 field as specified by bridgeUdfOffset4Offset in the packet. |
| INT bridgeUdfPortIndex | 1.3.6.1.4.1.139.2.4.11.1.1 | INTEGER | read-only | The port number on the board. Same as ifIndex. |
| INT bridgeUdfState | 1.3.6.1.4.1.139.2.4.11.1.3 | INTEGER | read-write | The state of this filter. There are four states: disabled, filter, forward and count. In the disabled state, this filter is ignored. In the filter state, a packet matching this filter will be filtered or discarded. In the forward state, a packet matching this filter will be forwarded. In the count state, a packet matching this filter will increment the bridgeUdfMatchCounts and the filter will be ignored for filtering and forwarding purposes. |
| bridgeUdfTable | 1.3.6.1.4.1.139.2.4.11 | not-accessible | A table maintaining user defined filtering information on each port on the board. | |
| INT bridgeUdfTypeMask | 1.3.6.1.4.1.139.2.4.11.1.12 | INTEGER | read-write | The value used to mask off the data value used for comparison on the type field in the packet. Don't care bits are zero. |
| INT bridgeUdfTypeOperand | 1.3.6.1.4.1.139.2.4.11.1.13 | INTEGER | read-write | The operand used in the comparison of the bridgeUdfTypeValue and the type field in the packet. |
| INT bridgeUdfTypeValue | 1.3.6.1.4.1.139.2.4.11.1.11 | INTEGER | read-write | The data value used for comparison on the type field in the packet. |
| fddi | 1.3.6.1.4.1.139.2.7 | |||
| INT fddiCfg68kRamSize | 1.3.6.1.4.1.139.2.7.1.11 | INTEGER | read-only | Management software RAM size on this FDDI board. |
| STR fddiCfg68kRev | 1.3.6.1.4.1.139.2.7.1.17 | DisplayString | read-only | Revision number and date of the management boot ROM software on this FDDI board. |
| INT fddiCfg960RamSize | 1.3.6.1.4.1.139.2.7.1.12 | INTEGER | read-only | Packet switch software RAM size on this FDDI board. |
| STR fddiCfg960Rev | 1.3.6.1.4.1.139.2.7.1.18 | DisplayString | read-only | Revision number and date of the packet switch software on this FDDI board. |
| STR fddiCfgBootRev | 1.3.6.1.4.1.139.2.7.1.16 | DisplayString | read-only | Revision number and date of the boot software on this FDDI board. |
| INT fddiCfgDualPortRamSize | 1.3.6.1.4.1.139.2.7.1.15 | INTEGER | read-only | The size of the dual port RAM used by the Galactica 1 gigabit GBus on this FDDI board. |
| STR fddiCfgExecFlashRev | 1.3.6.1.4.1.139.2.7.1.23 | DisplayString | read-only | The version number of the software loaded in the executable flash memory bank on this FDDI board. |
| INT fddiCfgFlashMemorySize | 1.3.6.1.4.1.139.2.7.1.10 | INTEGER | read-only | Number of bytes of flash memory on this FDDI board. |
| STR fddiCfgHardwareRev | 1.3.6.1.4.1.139.2.7.1.3 | DisplayString | read-only | The hardware revision number of this FDDI board. |
| INT fddiCfgHasherCacheTagSize | 1.3.6.1.4.1.139.2.7.1.14 | INTEGER | read-only | The number of bytes in the hasher cache on this FDDI board. Each address used 6 bytes. |
| STR fddiCfgManufactureDate | 1.3.6.1.4.1.139.2.7.1.1 | DisplayString | read-only | The manufacture date of this FDDI board. |
| STR fddiCfgMediaType | 1.3.6.1.4.1.139.2.7.1.9 | DisplayString | read-only | A string describing the media type of the FDDI board. For example Multi-mode fiber or Twisted Pair. |
| STR fddiCfgModulePartNumber | 1.3.6.1.4.1.139.2.7.1.20 | DisplayString | read-only | The Artel part number for this FDDI module. |
| STR fddiCfgModuleSerialNumber | 1.3.6.1.4.1.139.2.7.1.21 | DisplayString | read-only | The Artel serial number for this FDDI module. |
| INT fddiCfgNumberFddiPorts | 1.3.6.1.4.1.139.2.7.1.5 | INTEGER | read-only | The number of ports on this module. |
| STR fddiCfgPPFRev | 1.3.6.1.4.1.139.2.7.1.7 | DisplayString | read-only | The hardware revision and date of the FDDI chip set module. |
| STR fddiCfgPPFSerialNumber | 1.3.6.1.4.1.139.2.7.1.8 | DisplayString | read-only | The serial number of the FDDI chip set module. |
| STR fddiCfgPPFSoftwareRev | 1.3.6.1.4.1.139.2.7.1.19 | DisplayString | read-only | Revision number and date of the FDDI chip set module. |
| STR fddiCfgPPFType | 1.3.6.1.4.1.139.2.7.1.6 | DisplayString | read-only | A string describing the type of the FDDI chip set module. |
| STR fddiCfgSerialNumber | 1.3.6.1.4.1.139.2.7.1.4 | DisplayString | read-only | The serial number of this FDDI board. |
| INT fddiCfgSonicRamSize | 1.3.6.1.4.1.139.2.7.1.13 | INTEGER | read-only | Size of the RAM used by the Ethernet Controllers (Sonic) for packet processing.. |
| STR fddiCfgStoreFlashRev | 1.3.6.1.4.1.139.2.7.1.22 | DisplayString | read-only | The version number of the software loaded in the store flash memory bank on this FDDI board. |
| INT fddiCfgType | 1.3.6.1.4.1.139.2.7.1.2 | INTEGER | read-only | The type of board. |
| fddiConfiguration | 1.3.6.1.4.1.139.2.7.1 | |||
| INT fddiIpFragEnabled | 1.3.6.1.4.1.139.2.7.2.1 | INTEGER | read-write | Enables and disables IP fragmentation for the FDDI board. |
| fddiIpFragmentation | 1.3.6.1.4.1.139.2.7.2 | |||
| fddiPort | 1.3.6.1.4.1.139.2.7.3 | |||
| fddiPortEntry | 1.3.6.1.4.1.139.2.7.3.1.1 | not-accessible | The statics for a particular port on the FDDI board. | |
| CTR fddiPortFrameCheckErrs | 1.3.6.1.4.1.139.2.7.3.1.1.5 | Counter | read-only | The count of frames copied off the ring which had a bad FCS (Frame Check Sequence). |
| INT fddiPortIndex | 1.3.6.1.4.1.139.2.7.3.1.1.1 | INTEGER | read-only | The port number associated with this port. Always the same as ifIndex. |
| CTR fddiPortNotCopiedOffRingErrs | 1.3.6.1.4.1.139.2.7.3.1.1.3 | Counter | read-only | Equivalent to the ANSI FDDI attribute fddiMACNotCopied-Ct. The count of frames that should have been copied off the ring but were not. It is not required that the count be exact. |
| CTR fddiPortRingOpCounts | 1.3.6.1.4.1.139.2.7.3.1.1.4 | Counter | read-only | Equivalent to the ANSI FDDI attribute fddiMACRingOp-Ct. The count of the number of times the ring has entered the 'Ring Operational' state from the 'Ring Not Operational' state. It is not required that this count be exact. |
| INT fddiPortRxMcastEnabled | 1.3.6.1.4.1.139.2.7.3.1.1.2 | INTEGER | read-only | Enables and disables the reception of multicast frames on this port. |
| fddiPortTable | 1.3.6.1.4.1.139.2.7.3.1 | not-accessible | Statistics maintained for the ports on a FDDI board. | |
| galactica | 1.3.6.1.4.1.139.2 | |||
| node | 1.3.6.1.4.1.139.1 | |||
| INT nodeColdBoot | 1.3.6.1.4.1.139.1.3 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the node to reset which has the effect of resetting all the boards in the node. |
| IP nodeIpSlotAddr | 1.3.6.1.4.1.139.1.5.1.2 | IpAddress | read-write | The IP address of the board in slot nodeIpSlotIndex. |
| nodeIpSlotEntry | 1.3.6.1.4.1.139.1.5.1 | not-accessible | The IP address of one of the boards in the node. | |
| INT nodeIpSlotIndex | 1.3.6.1.4.1.139.1.5.1.1 | INTEGER | read-only | The slot number in the node. |
| nodeIpSlotTable | 1.3.6.1.4.1.139.1.5 | not-accessible | A table that contains the IP addresses of the boards in the node. | |
| OPA nodeMacSlotMap | 1.3.6.1.4.1.139.1.2 | Opaque | read-only | Each Starbridge board is assigned a base physical address. The physical address for each port is then assigned as (baseAddress + portIndex - 1). The nodeMacSlotMap is a 5 element array of the hex coded base addresses contained in the node with empty slots assigned the base address of 00:00:00:00:00:00. |
| STR nodeName | 1.3.6.1.4.1.139.1.1 | DisplayString | read-write | This node's administratively assigned name. |
| INT nodeResetNvRam | 1.3.6.1.4.1.139.1.4 | INTEGER | read-write | When queried, this object will always return the value 1. Setting this object to any value causes the node to reset the non-volatile RAM in each board in the node to default values. |
| PHY restrictedAddr | 1.3.6.1.4.1.139.2.4.1.1.1 | PhysAddress | read-write | The physical address to be restricted. |
| restrictedEntry | 1.3.6.1.4.1.139.2.4.1.1 | not-accessible | Information needed to restrict a particular physical address. | |
| INT restrictedStatus | 1.3.6.1.4.1.139.2.4.1.1.2 | INTEGER | read-write | Indicates the state of the entry. Invalid items will be removed from the table. |
| restrictedTable | 1.3.6.1.4.1.139.2.4.1 | not-accessible | A table of physical addresses that are restricted from being bridged through this node. Filtering is done on both source and destination address. | |
| INT sbCfg68kRamSize | 1.3.6.1.4.1.139.2.6.1.15 | INTEGER | read-only | Management software RAM size on this Starbridge board. |
| STR sbCfg68kRev | 1.3.6.1.4.1.139.2.6.1.21 | DisplayString | read-only | Revision number and date of the management boot ROM software on this Starbridge board. |
| INT sbCfg960RamSize | 1.3.6.1.4.1.139.2.6.1.16 | INTEGER | read-only | Packet switch software RAM size on this Starbridge board. |
| STR sbCfg960Rev | 1.3.6.1.4.1.139.2.6.1.22 | DisplayString | read-only | Revision number and date of the packet switch software on this Starbridge board. |
| STR sbCfgBootRev | 1.3.6.1.4.1.139.2.6.1.20 | DisplayString | read-only | Revision number and date of the boot software on this Starbridge board. |
| INT sbCfgDualPortRamSize | 1.3.6.1.4.1.139.2.6.1.19 | INTEGER | read-only | The size of the dual port RAM used by the Galactica 1 gigabit GBus on this Starbridge board. |
| STR sbCfgExecFlashRev | 1.3.6.1.4.1.139.2.6.1.26 | DisplayString | read-only | The version number of the software loaded in the executable flash memory bank on this Starbridge board. |
| INT sbCfgFlashMemorySize | 1.3.6.1.4.1.139.2.6.1.14 | INTEGER | read-only | Number of bytes of flash memory on this Starbridge board. |
| STR sbCfgHardwareRev | 1.3.6.1.4.1.139.2.6.1.3 | DisplayString | read-only | The hardware revision number of this Starbridge board. |
| INT sbCfgHasherCacheTagSize | 1.3.6.1.4.1.139.2.6.1.18 | INTEGER | read-only | The number of bytes in the hasher cache on this Starbridge board. Each address used 6 bytes. |
| INT sbCfgIfBd1NumPorts | 1.3.6.1.4.1.139.2.6.1.9 | INTEGER | read-only | The number of ports contained on interface card 1. |
| STR sbCfgIfBd1Rev | 1.3.6.1.4.1.139.2.6.1.7 | DisplayString | read-only | The hardware revision number of interface card 1. |
| STR sbCfgIfBd1SerialNum | 1.3.6.1.4.1.139.2.6.1.8 | DisplayString | read-only | The serial number of interface card 1. |
| INT sbCfgIfBd1Type | 1.3.6.1.4.1.139.2.6.1.6 | INTEGER | read-only | The interface type of interface card 1. |
| INT sbCfgIfBd2NumPorts | 1.3.6.1.4.1.139.2.6.1.13 | INTEGER | read-only | The number of ports contained on interface card 2. |
| STR sbCfgIfBd2Rev | 1.3.6.1.4.1.139.2.6.1.11 | DisplayString | read-only | The hardware revision number of interface card 2. |
| STR sbCfgIfBd2SerialNum | 1.3.6.1.4.1.139.2.6.1.12 | DisplayString | read-only | The serial number of interface card 2. |
| INT sbCfgIfBd2Type | 1.3.6.1.4.1.139.2.6.1.10 | INTEGER | read-only | The interface type of interface card 2. |
| STR sbCfgManufactureDate | 1.3.6.1.4.1.139.2.6.1.1 | DisplayString | read-only | The manufacture date of this Starbridge board. |
| STR sbCfgModulePartNumber | 1.3.6.1.4.1.139.2.6.1.23 | DisplayString | read-only | The Artel part number for this Starbridge module. |
| STR sbCfgModuleSerialNumber | 1.3.6.1.4.1.139.2.6.1.24 | DisplayString | read-only | The Artel serial number for this Starbridge module. |
| INT sbCfgNumberIfBoards | 1.3.6.1.4.1.139.2.6.1.5 | INTEGER | read-only | The number of interface cards on this module. |
| STR sbCfgSerialNumber | 1.3.6.1.4.1.139.2.6.1.4 | DisplayString | read-only | The serial number of this Starbridge board. |
| INT sbCfgSonicRamSize | 1.3.6.1.4.1.139.2.6.1.17 | INTEGER | read-only | Size of the RAM used by the Ethernet Controllers (Sonic) for packet processing.. |
| STR sbCfgStoreFlashRev | 1.3.6.1.4.1.139.2.6.1.25 | DisplayString | read-only | The version number of the software loaded in the store flash memory bank on this Starbridge board. |
| INT sbCfgType | 1.3.6.1.4.1.139.2.6.1.2 | INTEGER | read-only | The type of board |
| sbConfiguration | 1.3.6.1.4.1.139.2.6.1 | |||
| sbPort | 1.3.6.1.4.1.139.2.6.3 | |||
| sbPortEntry | 1.3.6.1.4.1.139.2.6.3.1.1 | not-accessible | The statics for a particular port on the Starbridge board. | |
| GAU sbPortErrorRate | 1.3.6.1.4.1.139.2.6.3.1.1.12 | Gauge | read-only | Port errors over the past ten seconds, expressed as a percentage. |
| GAU sbPortFramesPerSecond | 1.3.6.1.4.1.139.2.6.3.1.1.11 | Gauge | read-only | The number of data frames per second seen by the port. |
| INT sbPortIndex | 1.3.6.1.4.1.139.2.6.3.1.1.1 | INTEGER | read-only | The port number associated with this port. Always the same as ifIndex. |
| INT sbPortInitStats | 1.3.6.1.4.1.139.2.6.3.1.1.13 | INTEGER | read-write | This object always returns 1. Setting this object to any value causes the port statistics to be cleared. |
| STR sbPortName | 1.3.6.1.4.1.139.2.6.3.1.1.9 | DisplayString | read-write | Administratively assigned name for this port. |
| CTR sbPortRxBroadcastFrames | 1.3.6.1.4.1.139.2.6.3.1.1.3 | Counter | read-only | The number of broadcast frames received on this port. |
| INT sbPortRxBroadcastStatus | 1.3.6.1.4.1.139.2.6.3.1.1.8 | INTEGER | read-write | Administratively enables and disables the receipt of broadcasts on this port. |
| CTR sbPortRxBytes | 1.3.6.1.4.1.139.2.6.3.1.1.6 | Counter | read-only | The total number of bytes received on this port. |
| CTR sbPortRxMulticastFrames | 1.3.6.1.4.1.139.2.6.3.1.1.2 | Counter | read-only | The number of multicast frames received on this port. |
| CTR sbPortRxRuntErrors | 1.3.6.1.4.1.139.2.6.3.1.1.5 | Counter | read-only | The number of packets received that were smaller than the minimum size packet defined for this port. |
| sbPortTable | 1.3.6.1.4.1.139.2.6.3.1 | not-accessible | Statistics maintained for the ports on a Starbridge board. | |
| CTR sbPortTxBytes | 1.3.6.1.4.1.139.2.6.3.1.1.7 | Counter | read-only | The total number of bytes transmitted on this port. |
| INT sbPortUnidirectEnable | 1.3.6.1.4.1.139.2.6.3.2.1.2 | INTEGER | read-write | Administratively enables and disables uni-direct. |
| sbPortUnidirectEntry | 1.3.6.1.4.1.139.2.6.3.2.1 | not-accessible | The information needed for one uni-direct connection. | |
| INT sbPortUnidirectIndex | 1.3.6.1.4.1.139.2.6.3.2.1.1 | INTEGER | read-only | The index number assigned to this uni-direct channel. A unidirect channel consists of 2 ports. Channel 1 consists of port 1 and port 2 Channel 2 consists of port 3 and port 4 Channel 3 consists of port 5 and port 6 Channel 4 consists of port 7 and port 8 The odd numbered port is alwasy the receive port and the even numbered port is always the transmit port. |
| sbPortUnidirectTable | 1.3.6.1.4.1.139.2.6.3.2 | not-accessible | Table that supports the Artel uni-direct option. | |
| GAU sbPortUtilization | 1.3.6.1.4.1.139.2.6.3.1.1.10 | Gauge | read-only | Port usage over the past ten seconds, expressed as a percentage. |
| smBackplane | 1.3.6.1.4.1.139.2.5.2 | |||
| INT smBpArbTimer | 1.3.6.1.4.1.139.2.5.2.2 | INTEGER | read-only | The timeout period used to switch from asyncronous packets to syncronous packets. |
| INT smBpAsyncSlotsEnb | 1.3.6.1.4.1.139.2.5.2.4 | INTEGER | read-only | A bit string returned as an integer that indicates which boards are asynchronous. The least significant bit represents the board in slot 0. |
| smBpEntry | 1.3.6.1.4.1.139.2.5.2.7.1 | not-accessible | Information maintained on a single board. | |
| INT smBpIndex | 1.3.6.1.4.1.139.2.5.2.7.1.1 | INTEGER | read-only | The slot number of the board. |
| INT smBpMaxPktSize | 1.3.6.1.4.1.139.2.5.2.3 | INTEGER | read-only | The maximum packet size transmitted over the node's Galactica 1 gigabit GBus. |
| INT smBpSyncSlotsEnb | 1.3.6.1.4.1.139.2.5.2.5 | INTEGER | read-only | A bit string returned as an integer that indicates which boards are synchronous. The least significant bit represents the board in slot 0. |
| smBpTable | 1.3.6.1.4.1.139.2.5.2.7 | not-accessible | A table maintaining state information on each board in the node. | |
| INT smBpTableClearJabber | 1.3.6.1.4.1.139.2.5.2.7.1.4 | INTEGER | read-write | When read this object always returns 1. When set to any value, the System Manager will clear the smBpTableJabber object allowing the board to be re-enabled onto the Galactica 1 gigabit GBus. |
| INT smBpTableEnable | 1.3.6.1.4.1.139.2.5.2.7.1.2 | INTEGER | read-only | The current operational state of the board as viewed by the System Management board. |
| INT smBpTableJabber | 1.3.6.1.4.1.139.2.5.2.7.1.3 | INTEGER | read-only | True indicates that the board transmitted a packet that was larger than the maximum packet size and was disabled from the Galactica 1 gigabit GBus by the System Management board. This state will not be automatically re-set. The board cannot be re-enabled until manual intervention is taken by setting the smBpTableClearJabber object as defined below. |
| INT smBpType | 1.3.6.1.4.1.139.2.5.2.1 | INTEGER | read-only | The type of Galactica 1 gigabit GBus on this node. |
| INT smBpUtilization | 1.3.6.1.4.1.139.2.5.2.6 | INTEGER | read-only | The current percentage of Galactica 1 gigabit GBus utilization. |
| INT smCfg68kRamSize | 1.3.6.1.4.1.139.2.5.1.7 | INTEGER | read-only | Management software RAM size on this System Management board. |
| STR smCfg68kRev | 1.3.6.1.4.1.139.2.5.1.9 | DisplayString | read-only | Revision number and date of the management software on this System Management board. |
| STR smCfgBootRev | 1.3.6.1.4.1.139.2.5.1.8 | DisplayString | read-only | Revision number and date of the boot software on this System Management board. |
| STR smCfgExecFlashRev | 1.3.6.1.4.1.139.2.5.1.13 | DisplayString | read-only | The version number of the software loaded in the executable flash memory bank on this System Management board. |
| INT smCfgFlashMemSize | 1.3.6.1.4.1.139.2.5.1.6 | INTEGER | read-only | Number of bytes of flash memory on this System Management board. |
| STR smCfgHardwareRev | 1.3.6.1.4.1.139.2.5.1.3 | DisplayString | read-only | The hardware revision number of this System Management board. |
| PHY smCfgMacAddr | 1.3.6.1.4.1.139.2.5.1.5 | PhysAddress | read-only | The physical address of this System Management board. |
| STR smCfgManufactureDate | 1.3.6.1.4.1.139.2.5.1.1 | DisplayString | read-only | The manufacture date of this System Management board. |
| STR smCfgModulePartNumber | 1.3.6.1.4.1.139.2.5.1.10 | DisplayString | read-only | The Artel part number for this System Management module. |
| STR smCfgModuleSerialNumber | 1.3.6.1.4.1.139.2.5.1.11 | DisplayString | read-only | The Artel serial number for this System Management module. |
| STR smCfgSerialNumber | 1.3.6.1.4.1.139.2.5.1.4 | DisplayString | read-only | The serial number of this System Management board. |
| STR smCfgStoreFlashRev | 1.3.6.1.4.1.139.2.5.1.12 | DisplayString | read-only | The version number of the software loaded in the store flash memory bank on this System Management board. |
| INT smCfgType | 1.3.6.1.4.1.139.2.5.1.2 | INTEGER | read-only | The type of board. |
| smConfiguration | 1.3.6.1.4.1.139.2.5.1 | |||
| smModem | 1.3.6.1.4.1.139.2.5.5 | |||
| INT smModemCallBackEnable | 1.3.6.1.4.1.139.2.5.5.2 | INTEGER | read-write | Enables and disables the call-back feature of the modem. If enabled the modem will answer a call, then hang up and dial the number in smModemCallBackNumber. If disabled the modem will not hang up on any calls. |
| STR smModemCallBackNumber | 1.3.6.1.4.1.139.2.5.5.3 | DisplayString | read-write | A Hayes style dial string that the internal modem uses if call-back is enabled. The string should not contain the 'ATD' characters, but a leading 'P' may be used to initiate pulse dialing if needed. |
| INT smModemType | 1.3.6.1.4.1.139.2.5.5.1 | INTEGER | read-only | The modem type present on the node's System Management board. |
| smPowerSupply | 1.3.6.1.4.1.139.2.5.4 | |||
| INT smSupplyAcOk | 1.3.6.1.4.1.139.2.5.4.3 | INTEGER | read-only | A bit string returned as an integer that indicates the status of the AC power units. The least significant bit represents power supply 1. |
| INT smSupplyDcOk | 1.3.6.1.4.1.139.2.5.4.4 | INTEGER | read-only | A bit string returned as an integer that indicates the status of the DC power units. The least significant bit represents power supply 1. |
| INT smSupplyPresent | 1.3.6.1.4.1.139.2.5.4.1 | INTEGER | read-only | A bit string returned as an integer that represents the presence of the power supplies. The lease significant bit represents power supply 1 which the leftmost power supply. |
| smSupplyTable | 1.3.6.1.4.1.139.2.5.4.5 | not-accessible | A table of strings describing the status of the chassis power supplies. | |
| smSupplyTableEntry | 1.3.6.1.4.1.139.2.5.4.5.1 | not-accessible | The status of one power supply in the chassis. | |
| INT smSupplyTableIndex | 1.3.6.1.4.1.139.2.5.4.5.1.1 | INTEGER | read-only | The number of the power supply in the chassis, numbered from left to right. |
| STR smSupplyTableStatus | 1.3.6.1.4.1.139.2.5.4.5.1.2 | DisplayString | read-only | A text description of the status of the power supply. One of: 'NOT PRESENT', 'OFF', 'ON' or 'FAILURE'. |
| INT smSupplyType | 1.3.6.1.4.1.139.2.5.4.2 | INTEGER | read-only | A bit string returned as an integer that indicates the type of power supply present. Two bits are assigned to each power supply with the 2 least significant bits representing power supply 1. The bits are encoded such that: 00 invalid 01 No supply present 10 DC supply 11 AC supply |
| starbridge | 1.3.6.1.4.1.139.2.6 | |||
| systemManagement | 1.3.6.1.4.1.139.2.5 |
RFC description
Monitors node, board, and network interface resources on Chipcom ARTEL Galactica devices.
Start monitoring Artel Video Systems SDI video-over-fiber/IP transport equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.