A3COM-HUAWEI-VOSIP-MIB

All MIBs › A3COM-HUAWEI-VOSIP-MIB

Organization: Huawei 3Com Technologies co., Ltd.

Last Updated: 2005-03-15

Category: Telephony and VoIP, Vendor: H3C/HH3C

Description: Manages SIP protocol configuration on H3C/3Com voice gateways, including SIP server addresses, registration settings, and SIP dial peer configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is A3COM-HUAWEI-VOSIP-MIB?

A3COM-HUAWEI-VOSIP-MIB is an H3C/3Com vendor MIB for managing SIP (Session Initiation Protocol) client configuration on H3C/3Com voice gateways, covering SIP server addresses, registration settings, and SIP dial-peer configuration as stated in its module description. It primarily exposes configuration objects for establishing and maintaining SIP-based multimedia sessions (IP telephony, conferencing) rather than runtime performance counters. Its monitoring relevance is largely in confirming SIP client/registration configuration status, e.g., whether the gateway is correctly registered with its configured SIP server, which functions as a software/service-status check for the VoIP signaling stack. It is a vendor-specific management layer built on top of the standard SIP protocol, per its description referencing SIP as an application-layer control protocol, though it is not shown depending on other SNMP standards MIBs. It's deployed on H3C/3Com voice gateways used for SIP-based IP telephony and multimedia session establishment. Engineers can download the A3COM-HUAWEI-VOSIP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in A3COM-HUAWEI-VOSIP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C/3Com SIP voice gateway

Monitoring Examples

No concrete object or table names were provided for this module, so specific OIDs cannot be cited; based on its stated scope, a realistic use would be reading back SIP server address and registration configuration objects to confirm the gateway is correctly registered, and checking SIP dial-peer configuration to verify call-routing rules are as expected. Confirming exact object names would require the underlying MIB source.

What Can Be Monitored

SIP server address configuration
SIP registration status/settings
SIP dial-peer configuration

Imported Objects

From A3COM-HUAWEI-OID-MIB

h3cVoice

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

RowStatus

How to Use in IPNetwork Monitor

Example using h3cSIPMsgSend OID:

Select an H3C/3Com SIP voice gateway as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type h3cSIPMsgSend into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of messages which a SIP gateway has sent. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
h3cVoSIP	1.3.6.1.4.1.43.45.1.10.2.39.12			This MIB contains objects to manage the SIP client configuration. Session Initiation Protocol (SIP) is an application layer control protocol that can establish, modify, and terminate multimedia sessions such as IP phone calls, multimedia distribution, and multimedia conferences.
h3cSIPClientMIB	1.3.6.1.4.1.43.45.1.10.2.39.12.1
h3cSIPClientConfigObjects	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1
OCT h3cSIPID	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.1	OCTET STRING	read-write	The unique identification of a SIP gateway. This value couldn't be modified unless h3cSIPRegisterEnable is 'off'.
INT h3cSIPPasswordType	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.2	INTEGER	read-write	The display type of a SIP gateway password. By default, this object should have the value simple(1). This value couldn't be modified unless h3cSIPRegisterEnable is 'off'.
OCT h3cSIPPassword	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.3	OCTET STRING	read-write	A SIP gateway password. This value couldn't be modified unless h3cSIPRegisterEnable is 'off'.
IPt h3cSIPSourceIPAddressType	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.4	InetAddressType	read-write	The source IP address type of the local peer acting as UA (User Agent). This value couldn't be modified unless h3cSIPRegisterEnable is 'off'.
IP h3cSIPSourceIP	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.5	InetAddress	read-write	The source IP address of the local peer acting as UA (User Agent). This value couldn't be modified unless h3cSIPRegisterEnable is 'off'.
INT h3cSIPRegisterMode	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.6	INTEGER	read-write	The object describes the method to send the type of telephone number. gatewayAll The register mode is gateway mode and the register message contains all the POTS numbers. gatewaySingle The register mode is gateway mode and every register message contains only one POTS number. phoneNumber The register mode is phone mode. Note: Please configure the object hwSIPRegisterPhoneNumber after hwSIPRegisterMode has been set to phoneNumber. This value couldn't be modified unless h3cSIPRegisterEnable is 'off'.
OCT h3cSIPRegisterPhoneNumber	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.7	OCTET STRING	read-write	The object describes the telephone number which is going to be registered. Note: Please set value of the object h3cIPRegisterMode to phoneNumber before configure this node. This value couldn't be modified unless h3cSIPRegisterEnable is 'off'.
INT h3cSIPRegisterEnable	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.8	INTEGER	read-write	The object describes register enable or not, default is off. Only if h3cSIPServerConfigTable is configured well, then this node could be set 'on(1)' successfully.
INT h3cSIPTrapsControl	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.9	INTEGER	read-write	Indicates whether the SIP module is permitted to generate traps.
INT h3cSIPStatisticClear	1.3.6.1.4.1.43.45.1.10.2.39.12.1.1.10	INTEGER	read-write	The object is used to clear the statistic information of a SIP gateway. Note: this object only supports set operation.
h3cSIPServerConfigTable	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2		not-accessible	A list of the SIP server configuration entries.
h3cSIPServerConfigEntry	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2.1		not-accessible	A SIP server configuration entry contains some associated information, e.g. IP address, port, etc.
IPt h3cSIPServerIPAddressType	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2.1.1	InetAddressType	accessible-for-notify	The source IP address type of a SIP server.
IP h3cSIPServerIPAddress	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2.1.2	InetAddress	accessible-for-notify	The IP address of a SIP server.
I32 h3cSIPServerPort	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2.1.3	Integer32	accessible-for-notify	The port of a SIP server.
INT h3cSIPServerType	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2.1.4	INTEGER	read-create	The type of SIP Server.
INT h3cSIPAcceptType	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2.1.5	INTEGER	read-create	The accept type of SIP calls. By default, the object value is all(2).
ROW h3cSIPServerStatus	1.3.6.1.4.1.43.45.1.10.2.39.12.1.2.1.6	RowStatus	read-create	This object is used to create, delete or modify a row in this table. To create a new row, hwSIPServerType must be specified. Note: h3cSIPRegisterEnable must be specifed 'off' before modifing or destroying an existing row or creating a new row.
h3cSIPMsgStatTable	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3		not-accessible	A list of SIP message statistics entries.
h3cSIPMsgStatEntry	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3.1		not-accessible	A collection of statistics kept for a SIP message.
SIP h3cSIPMsgIndex	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3.1.1	SipMsgType	not-accessible	The index of a SIP message.
OCT h3cSIPMsgName	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3.1.2	OCTET STRING	read-only	The name of a SIP message.
C32 h3cSIPMsgSendEx	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3.1.3	Counter32	read-only	The number of messages which a SIP gateway has sent.
C32 h3cSIPMsgOKSend	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3.1.4	Counter32	read-only	The number of successful messages which a SIP gateway has sent.
C32 h3cSIPMsgReceive	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3.1.5	Counter32	read-only	The number of messages which a SIP gateway has received.
C32 h3cSIPMsgOKReceive	1.3.6.1.4.1.43.45.1.10.2.39.12.1.3.1.6	Counter32	read-only	The number of successful messages which a SIP gateway has received.
h3cSIPMsgResponseStatTable	1.3.6.1.4.1.43.45.1.10.2.39.12.1.4		not-accessible	A list of the SIP message response code statistic entries.
h3cSIPMsgResponseStatEntry	1.3.6.1.4.1.43.45.1.10.2.39.12.1.4.1		not-accessible	The information of SIP response code.
I32 h3cSIPMsgResponseIndex	1.3.6.1.4.1.43.45.1.10.2.39.12.1.4.1.1	Integer32	not-accessible	The index of a SIP message response code.
OCT h3cSIPMsgResponseCode	1.3.6.1.4.1.43.45.1.10.2.39.12.1.4.1.2	OCTET STRING	read-only	The SIP message response code.
C32 h3cSIPResCodeRecvCount	1.3.6.1.4.1.43.45.1.10.2.39.12.1.4.1.3	Counter32	read-only	The number of SIP response code which a SIP gateway has received.
C32 h3cSIPResCodeSendCount	1.3.6.1.4.1.43.45.1.10.2.39.12.1.4.1.4	Counter32	read-only	The number of SIP response code which a SIP gateway has sent.
h3cSIPTrapStubObjects	1.3.6.1.4.1.43.45.1.10.2.39.12.3
OCT h3cSIPRegisterFailReason	1.3.6.1.4.1.43.45.1.10.2.39.12.3.1	OCTET STRING	accessible-for-notify	The object describes the reason that a SIP gateway fails to register.
SIP h3cSIPAuthenReqMethod	1.3.6.1.4.1.43.45.1.10.2.39.12.3.2	SipMsgType	accessible-for-notify	The object denotes the method of a request that fails to authenticate.
h3cSIPClientNotifications	1.3.6.1.4.1.43.45.1.10.2.39.12.4
NTF h3cSIPRegisterFailure	1.3.6.1.4.1.43.45.1.10.2.39.12.4.1			The trap is generated when a SIP gateway fails to register.
NTF h3cSIPAuthenticateFailure	1.3.6.1.4.1.43.45.1.10.2.39.12.4.2			The trap is generated when a request with its credential fail to authenticate.
NTF h3cSIPServerSwitch	1.3.6.1.4.1.43.45.1.10.2.39.12.4.3			The trap is generated when a switch happens between master and slave SIP server.

RFC description

MIB for managing SIP (Session Initiation Protocol) client configuration on 3COM/Huawei networking equipment, enabling SNMP management of SIP features and VoIP functionality.

Start monitoring H3C/3Com SIP voice gateways with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download A3COM-HUAWEI-VOSIP-MIB