A3COM-HUAWEI-DOT11-STATION-MIB

All MIBs › A3COM-HUAWEI-DOT11-STATION-MIB

Organization: Hangzhou H3C Technologies Co., Ltd.

Last Updated: 2010-09-02

Category: Vendor: H3C/HH3C, Wireless and WLAN

Description: Tracks associated 802.11 client station information including signal strength and data rates on H3C WLAN systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is A3COM-HUAWEI-DOT11-STATION-MIB?

A3COM-HUAWEI-DOT11-STATION-MIB is a Hangzhou H3C Technologies proprietary MIB reporting connected wireless station (client) configuration and statistics under a CAPWAP-based Fit-AP/AC architecture. Its station-associate table, keyed by MAC address, records IP address, username, TX rate set, up time, signal strength, RSSI, channel, power-save mode, VLAN ID, SSID name, authentication mode, AKM mode, security ciphers, encryption mode, RX SNR/rate, TX rate, vendor name, radio mode, and RX noise. As a status/performance MIB it lets an administrator confirm signal quality and security posture of each connected wireless client on an H3C wireless LAN. It is deployed on H3C wireless LAN controllers and managed access points. Engineers can download the A3COM-HUAWEI-DOT11-STATION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in A3COM-HUAWEI-DOT11-STATION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C wireless LAN controllers and managed access points

Monitoring Examples

An administrator checks h3cDot11StationSignalStrength and h3cDot11StationRxSNR to diagnose a wireless client's poor connection quality on an H3C wireless LAN.

What Can Be Monitored

per-station signal quality, security mode, and rate statistics

Imported Objects

From A3COM-HUAWEI-DOT11-REF-MIB

H3cDot11AKMType
H3cDot11AssocFailType
H3cDot11AuthenType
H3cDot11AuthorFailType
H3cDot11ChannelScopeType
H3cDot11CipherType
H3cDot11ObjectIDType
H3cDot11RadioScopeType
H3cDot11RadioType
H3cDot11RadioType2
H3cDot11SSIDEncryptModeType
H3cDot11SSIDStringType
H3cDot11SecIEStatusType
h3cDot11	MODULE-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DateAndTime
MacAddress

How to Use in IPNetwork Monitor

Example using h3cDot11StationRxFrameCnt OID:

Select an H3C wireless controller or access point as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type h3cDot11StationRxFrameCnt into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Represents the count of frames that are received by AP from station. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
H3C h3cDot11CurrAPID	1.3.6.1.4.1.43.45.1.10.2.75.3.1.2.1.1	H3cDot11ObjectIDType	read-only	To uniquely identify each AP, and relation-ship between h3cDot11CurrAPID and AP device will be static.
H3C h3cDot11CurrRadioID	1.3.6.1.4.1.43.45.1.10.2.75.3.1.2.1.2	H3cDot11RadioScopeType	read-only	Represents each radio.
I32 h3cDot11CurrWlanID	1.3.6.1.4.1.43.45.1.10.2.75.3.1.2.1.3	Integer32	read-only	Represents WLAN ID of the BSS the station associated to.
OCT h3cDot11StaDisconnectReason	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.12	OCTET STRING	accessible-for-notify	Reason why the station disconnects with the AP.
OCT h3cDot11StaRxDataRatePkts	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.22	OCTET STRING	read-only	Represents how many data frames of each rate have been sent to station.
C64 h3cDot11StaRxErrDataFrameCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.19	Counter64	read-only	Represents the count of error data frames that are received by AP from station.
h3cDot11STATION	1.3.6.1.4.1.43.45.1.10.2.75.3			This MIB defines the configuration and statistic information of stations. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associated with the AP. station (Client Station) A wireless device in a wireless network associated with an access point. MIC Message Integrity Check. A MIC can, optionally, be added to WEP-encrypted 802.11 frames. SSID Radio Service Set ID. It is used for identification during association. STA (WSTA) A non-AP 802.11 wireless station. WEP Wired Equivalent Privacy. 'WEP' is generally used to refer to 802.11 encryption. RSSI It is the received signal strength indication. It suggests the quality of received signal. RTS Request to Send, it is used to gain control of the medium for the transmission of 'large' frames, in which 'large' is defined by the RTS threshold in the network card driver. CTS Clear to Send, it is used to answer RTS frames. AKM The authentication and key management method defined by 802.11i, and which includes 802.1x and pre-shared key.
IP h3cDot11StationACIPAddress	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.9	IpAddress	accessible-for-notify	For roam-in station, it represents the ip address of home AC. For roam-out station, it represents the ip address of foreign AC.
OCT h3cDot11StationACIPv6Add	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.14	OCTET STRING	accessible-for-notify	For roam-in station, it represents the IPv6 address of home AC. For roam-out station, it represents the IPv6 address of foreign AC.
I32 h3cDot11StationAid	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.10	Integer32	read-only	Represents the association identification number of station.
H3C h3cDot11StationAKMMode	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.14	H3cDot11AKMType	read-only	Represents the key management mode defined by 802.11i.
OCT h3cDot11StationAPName	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.10	OCTET STRING	accessible-for-notify	Name of the AP which the station connects to.
h3cDot11StationAPRelationEntry	1.3.6.1.4.1.43.45.1.10.2.75.3.1.2.1		not-accessible	Each entry contains relation-ship information with AP, Radio and WLANID of each station.
h3cDot11StationAPRelationTable	1.3.6.1.4.1.43.45.1.10.2.75.3.1.2		not-accessible	This table contains relation-ship between station, AP, Radio and WLANID, and the detailed information of station is kept in the h3cDot11StaAssociateTable table.
H3C h3cDot11StationAssocFailCause	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.4	H3cDot11AssocFailType	accessible-for-notify	Represents the cause of the station association failure.
NTF h3cDot11StationAssocFailTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.4			This trap is sent if a station association fails.
h3cDot11StationAssociateEntry	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1		not-accessible	Each entry contains association information of each station.
h3cDot11StationAssociateTable	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1		not-accessible	This table contains the information of stations which are associating with the wireless network (current AC).
DAT h3cDot11StationAssTime	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.30	DateAndTime	read-only	Represents the time at which the station connected.
NTF h3cDot11StationAuthenErrorTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.2			This notification is to indicate which station happened authentication failure.
H3C h3cDot11StationAuthenMode	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.13	H3cDot11AuthenType	read-only	Represents the Authentication mode defined by 802.11.
INT h3cDot11StationAuthMode	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.13	INTEGER	accessible-for-notify	Represents station's authentication mode.
H3C h3cDot11StationAuthorFailCause	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.5	H3cDot11AuthorFailType	accessible-for-notify	Represents the cause of the station authorization failure.
NTF h3cDot11StationAuthorFailTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.3			This trap is sent if a station authorization fails.
NTF h3cDot11StationAuthorSuccTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.6			This trap is sent when a station is authorized successfully.
MAC h3cDot11StationBSSID	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.11	MacAddress	accessible-for-notify	BSSID which the station connects to.
H3C h3cDot11StationChannel	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.8	H3cDot11ChannelScopeType	read-only	Represents current radio channel used by station.
NTF h3cDot11StationDeAssocTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.5			This trap is sent if a station de-association occurred.
NTF h3cDot11StationDisconnectTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.8			This notification is sent when station disconnects with AP.
C64 h3cDot11StationDropFrameBytes	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.6	Counter64	read-only	Represents how many bytes are dropped.
C32 h3cDot11StationDropFrameCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.3	Counter32	read-only	Represents the count of frames that are dropped.
OCT h3cDot11StationFailCauseDesc	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.6	OCTET STRING	accessible-for-notify	Represents the failure description of the station.
IP h3cDot11StationIPAddress	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.2	IpAddress	read-only	Represents the IP address of the station.
MAC h3cDot11StationMAC	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.1	MacAddress	not-accessible	Represents the unique MAC Address of station.
MAC h3cDot11StationMACAddress	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.23	MacAddress	read-only	Represents MAC Address of station.
NTF h3cDot11StationMICErrorTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.1			This notification is to indicate the occurrence of a MIC failure in a certain station.
h3cDot11StationMtGroup	1.3.6.1.4.1.43.45.1.10.2.75.3.1
h3cDot11StationNotifyGroup	1.3.6.1.4.1.43.45.1.10.2.75.3.2
INT h3cDot11StationPowerSaveMode	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.9	INTEGER	read-only	Represents the power management mode of this station. The following values are supported: active(1) - This station is not in power-save mode and it is actively sending or receiving data. powersave(2) - This station is in power-save mode and it wakes up after sometime to check for buffer data.
H3C h3cDot11StationRadioMode	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.21	H3cDot11RadioType	read-only	Represents which radio type supported by the station. The WLAN system support the following possible radio types. dot11a(1), dot11b(2), dot11g(4), dot11n(8) For a station,it could support only one radio type at the same time.
H3C h3cDot11StationRadioMode2	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.29	H3cDot11RadioType2	read-only	Represents which radio type supported by the station. The WLAN system support the following possible radio types. dot11a(1), dot11b(2), dot11g(4), dot11an(8), dot11gn(16) For a station,it could support only one radio type at the same time.
U32 h3cDot11StationRoamingTime	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.8	Unsigned32	accessible-for-notify	Represents the time at which the station roamed.
NTF h3cDot11StationRoamingTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.7			This trap is sent when a station roamed successfully.
I32 h3cDot11StationRSSI	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.7	Integer32	read-only	Represents a device-dependent measure of the RSSI. It is the received signal strength indication. The maximum value is defined by chip set vendors
C64 h3cDot11StationRxDataFrameBytes	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.16	Counter64	read-only	Represents how many bytes of data frames have been received from station.
C32 h3cDot11StationRxDataFrameCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.14	Counter32	read-only	Represents how many data frames have been received from station.
C32 h3cDot11StationRxFragCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.18	Counter32	read-only	Represents the number of fragmented data frames that received from station.
C64 h3cDot11StationRxFrameBytes	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.4	Counter64	read-only	Represents the count of bytes that are received by AP from station.
C32 h3cDot11StationRxFrameCntEx	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.1	Counter32	read-only	Represents the count of frames that are received by AP from station.
I32 h3cDot11StationRxNoise	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.22	Integer32	read-only	Represents the received noise of the station.
I32 h3cDot11StationRxRate	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.19	Integer32	read-only	Represents the reception rate of frame.
C64 h3cDot11StationRxRetryBytes	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.9	Counter64	read-only	Represents the count of bytes that are retransmitted to AP from station.
C32 h3cDot11StationRxRetryPkts	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.7	Counter32	read-only	Represents the count of frames that are retransmitted to AP from station.
I32 h3cDot11StationRxSNR	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.17	Integer32	read-only	Represents the signal and noise strength ratio of frame reception.
I32 h3cDot11StationRxSpeed	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.25	Integer32	read-only	Represents the bytes of received data frames from the station per second in sample interval.
H3C h3cDot11StationSecIEStatus	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.27	H3cDot11SecIEStatusType	read-only	Represents the security Information element for this station.
H3C h3cDot11StationSecurityCiphers	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.15	H3cDot11CipherType	read-only	Represents the frame encryption cipher type used by station.
U32 h3cDot11StationSessionDuration	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.7	Unsigned32	accessible-for-notify	Represents the duration of the station sesssion.
DAT h3cDot11StationSessionStartTime	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.3	DateAndTime	accessible-for-notify	Represents the time at which the station connected.
I32 h3cDot11StationSignalStrength	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.6	Integer32	read-only	Represents a device-dependent measure of the signal strength of latest packet received from this station.
H3C h3cDot11StationSSIDEncryptMode	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.16	H3cDot11SSIDEncryptModeType	read-only	Represents the encryption mode for this ESS.
STR h3cDot11StationSSIDName	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.12	H3cDot11SSIDStringType	read-only	Represents the ESS name.
h3cDot11StationStatisEntry	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1		not-accessible	This entry contains statistics and status for each station.
h3cDot11StationStatisTable	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3		not-accessible	This table contains statistics and status of all stations in the h3cDot11StaAssociateTable.
C32 h3cDot11StationSuccessTxCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.12	Counter32	read-only	Represents how many frames have been successfully sent to station.
C32 h3cDot11StationSuccessTxDataCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.13	Counter32	read-only	Represents how many data frames have been successfully sent to station.
C64 h3cDot11StationThroughput	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.11	Counter64	read-only	Represents how many payload bytes of data frame are sent and received by station.
MAC h3cDot11StationTrapBSSID	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.1	MacAddress	accessible-for-notify	Represents on which BSSID of AP the event happened.
h3cDot11StationTraps	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0
MAC h3cDot11StationTrapStaMAC	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.2	MacAddress	accessible-for-notify	Represents the MAC address of station which happened message integrity check (MIC) errors.
h3cDot11StationTrapVarObjects	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1
C64 h3cDot11StationTxDataFrameBytes	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.17	Counter64	read-only	Represents how many bytes of data frames have been sent to station.
C32 h3cDot11StationTxDataFrameCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.15	Counter32	read-only	Represents how many data frames have been sent to station.
C64 h3cDot11StationTxFrameBytes	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.5	Counter64	read-only	Represents the count of bytes that are sent to station from AP.
C32 h3cDot11StationTxFrameCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.2	Counter32	read-only	Represents the count of frames that are sent to station from AP.
I32 h3cDot11StationTxRate	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.18	Integer32	read-only	Represents the transmission rate of frame.
OCT h3cDot11StationTxRateSet	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.4	OCTET STRING	read-only	Represents the current transmit data rates for this station. Each byte will represent one rate. If the MSB(Most significant bit) is set, then this rate is a mandantory rate. Otherwise, it is optional.
C64 h3cDot11StationTxRetryBytes	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.10	Counter64	read-only	Represents the count of bytes that are retransmitted to station from AP.
C32 h3cDot11StationTxRetryPkts	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.8	Counter32	read-only	Represents the count of frames that are retransmitted to station from AP.
I32 h3cDot11StationTxSpeed	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.24	Integer32	read-only	Represents the bytes of transmitted data frames to the station per second in sample interval.
U32 h3cDot11StationUpTime	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.5	Unsigned32	read-only	The time in seconds, how long this station has been associated with this device.
TIK h3cDot11StationUpTimeTicks	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.28	TimeTicks	read-only	Represents how long this station has been associated with this device.
OCT h3cDot11StationUserName	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.3	OCTET STRING	read-only	Represents the user name of the station.
OCT h3cDot11StationVendorName	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.20	OCTET STRING	read-only	Represents the vendor name of the station.
I32 h3cDot11StationVlanId	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.11	Integer32	read-only	Represents Vlan ID to which the station is associated.
INT h3cDot11StationWmmMode	1.3.6.1.4.1.43.45.1.10.2.75.3.1.1.1.26	INTEGER	read-only	Represents the QoS mode of station. The following values are supported: wmm(1) - This QoS function is supported by this station. nonwmm(2) - This QoS function is not supported by this station.
OCT h3cDot11StaTxDataRatePkts	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.21	OCTET STRING	read-only	Represents how many data frames of each rate have been received from station.
C64 h3cDot11StaTxRetryDataFrameCnt	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.20	Counter64	read-only	Represents the count of data frames that are retransmitted to station from AP.
OCT h3cDot11StaTxSignalStrengthPkts	1.3.6.1.4.1.43.45.1.10.2.75.3.1.3.1.23	OCTET STRING	read-only	Represents how many data frames of different signal strength have been received from station.
NTF h3cDot11UserDisconnectTrap	1.3.6.1.4.1.43.45.1.10.2.75.3.2.0.9			This notification is sent when user disconnects with AP.
OCT h3cDot11UserName	1.3.6.1.4.1.43.45.1.10.2.75.3.2.1.15	OCTET STRING	accessible-for-notify	Represents the user name.

RFC description

802.11 wireless station statistics, association events, and authentication traps for H3C/Huawei APs.

Start monitoring H3C wireless controllers and APs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download A3COM-HUAWEI-DOT11-STATION-MIB