All MIBs › ZhoneVdsl-MIB › zhoneVdslPhysCurrStatus
zhoneVdslPhysCurrStatus
Module: ZhoneVdsl-MIB
OID (symbolic): ZhoneVdsl-MIB::zhoneVdslPhysCurrStatus
OID (numeric): 1.3.6.1.4.1.5504.5.13.1.1.2.1.7
Node type: OBJECT-TYPE
Type: Bits
Access: read-only
Description: Indicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are:
0 noDefect There are no defects on the line.
1 lossOfFraming Vtu failure due to not receiving a valid frame.
2 lossOfSignal Vtu failure due to not receiving signal.
3 lossOfPower Vtu failure due to loss of power.
4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7.
5 lossOfLink Vtu failure due to inability to link with peer Vtu. Set whenever the transceiver is in the 'Warm Start' state.
6 dataInitFailure Vtu failure during initialization due to bit errors corrupting startup exchange data.
7 configInitFailure Vtu failure during initialization due to peer Vtu not able to support requested configuration.
8 protocolInitFailure Vtu failure during initialization due to incompatible protocol used by the peer Vtu.
9 noPeerVtuPresent Vtu failure during initialization due to no activation sequence detected from peer Vtu.
This is intended to supplement ifOperStatus.
What is zhoneVdslPhysCurrStatus?
Bit map of the line's current defects: noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8) and noPeerVtuPresent(9). It complements ifOperStatus; for example noPeerVtuPresent means no activation sequence was heard, usually an unplugged or dead modem.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.5504.5.13.1.1.2.1.7 snmpwalk -v2c -c public <target> ZhoneVdsl-MIB::zhoneVdslPhysCurrStatus
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.5504.5.13.1.1.2.1.7.1 snmpget -v2c -c public <target> ZhoneVdsl-MIB::zhoneVdslPhysCurrStatus.1
Start monitoring Zhone Technologies DSLAM, VDSL CPE modem/router (line-rate/sync-training/error-counter status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the ZhoneVdsl-MIB::zhoneVdslPhysCurrStatus OID value, configure state conditions and alerts, and monitor any Zhone Technologies DSLAM, VDSL CPE modem/router (line-rate/sync-training/error-counter status) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.5504 | Zhone | BITSTORM-HP-160-MIB |
| 1.3.6.1.4.1.5504.5 | zhonePhysical | Zhone |
| 1.3.6.1.4.1.5504.5.13 | zhoneVdsl | Zhone |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.5504.5.13.1 | zhoneVdslLineMib | ZhoneVdsl-MIB |
| 1.3.6.1.4.1.5504.5.13.1.1 | zhoneVdslMibObjects | ZhoneVdsl-MIB |
| 1.3.6.1.4.1.5504.5.13.1.1.2 | zhoneVdslPhysTable | ZhoneVdsl-MIB |
| 1.3.6.1.4.1.5504.5.13.1.1.2.1 | zhoneVdslPhysEntry | ZhoneVdsl-MIB |
| 1.3.6.1.4.1.5504.5.13.1.1.2.1.7 | zhoneVdslPhysCurrStatus | ZhoneVdsl-MIB |