All MIBs › Zhone-VOICE-ANALOG-IF-MIB › zhoneVaIfCfgMaintenanceMode
zhoneVaIfCfgMaintenanceMode
Module: Zhone-VOICE-ANALOG-IF-MIB
OID (symbolic): Zhone-VOICE-ANALOG-IF-MIB::zhoneVaIfCfgMaintenanceMode
OID (numeric): 1.3.6.1.4.1.5504.5.6.1.1.1.8
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: Indicates the maintenance modes of the Analog voice interface.
loopback options for Fxo and Fxs cards (Zhone specific)
-------------------------------------------------------
CODEC
T1/E1 DS0 ---------------------------
<------- <--------------- -----------------
Network PCM Bus ^ Digital ^
| to analog Converter|
| |
| |
| |
Digital loopback Analog loopback
| |
-------> -------- ->--------------------------------------------->
off(1) - the interface is not in maintenance mode.
ifDigitalLoopback(2) This mode is set by the managed system to perform the
Digital loopback test.
ifAnalogLoopback(3) This mode is set by the managed system to perform the
Analog loopback test. What is zhoneVaIfCfgMaintenanceMode?
Puts this analog voice interface into a diagnostic loopback mode: off(1) for normal operation, ifDigitalLoopback(2) to loop the signal back at the DS0/PCM digital level, or ifAnalogLoopback(3) to loop it back after digital-to-analog conversion. An admin uses ifAnalogLoopback to verify the full analog path including the codec, or ifDigitalLoopback to isolate a digital-side problem, when troubleshooting a suspected line fault.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.5504.5.6.1.1.1.8 snmpwalk -v2c -c public <target> Zhone-VOICE-ANALOG-IF-MIB::zhoneVaIfCfgMaintenanceMode
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.5504.5.6.1.1.1.8.1 snmpget -v2c -c public <target> Zhone-VOICE-ANALOG-IF-MIB::zhoneVaIfCfgMaintenanceMode.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.5504.5.6.1.1.1.8.1 i <value>
Start monitoring Zhone integrated access device / multiservice access node (E&M/FXS/FXO port hook/line status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the Zhone-VOICE-ANALOG-IF-MIB::zhoneVaIfCfgMaintenanceMode OID value, configure state conditions and alerts, and monitor any Zhone integrated access device / multiservice access node (E&M/FXS/FXO port hook/line status) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.5504 | zhone | Zhone |
| 1.3.6.1.4.1.5504.5 | zhonePhysical | Zhone |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.5504.5.6 | zhoneVaIfObjects | Zhone-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.5504.5.6.1 | zhoneVaIfGeneralObjects | Zhone-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.5504.5.6.1.1 | zhoneVaIfCfgTable | Zhone-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.5504.5.6.1.1.1 | zhoneVaIfCfgEntry | Zhone-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.5504.5.6.1.1.1.8 | zhoneVaIfCfgMaintenanceMode | Zhone-VOICE-ANALOG-IF-MIB |