All MIBs › ZHONE-Wan-MIB › zhoneLoopbackConfig
zhoneLoopbackConfig
Module: ZHONE-Wan-MIB
OID (symbolic): ZHONE-Wan-MIB::zhoneLoopbackConfig
OID (numeric): 1.3.6.1.4.1.5504.5.2.2.1.8
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This variable represents the desired loopback configuration of the DS1 interface. Agents supporting read/write access should return inconsistentValue in response to a requested loopback state that the interface does not support. The values mean:
noLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as its value.
lineLoop The received signal at this interface does not go through the device (minimum penetration) but is looped back out.
localLoop The transmitted signal at this interface is looped back and received by the same interface. What is transmitted onto the line is product dependent.
payloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function.
What is zhoneLoopbackConfig?
Selects the loopback mode requested on this DS1/E1 interface -- none, a line loopback close to the wire, a local loopback of the transmit signal back into the receiver, or a payload loopback of the framed signal -- and returns inconsistentValue if the interface can't support the requested mode.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.5504.5.2.2.1.8 snmpwalk -v2c -c public <target> ZHONE-Wan-MIB::zhoneLoopbackConfig
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.5504.5.2.2.1.8.1 snmpget -v2c -c public <target> ZHONE-Wan-MIB::zhoneLoopbackConfig.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.5504.5.2.2.1.8.1 i <value>
Start monitoring Zhone broadband CPE / access gateways, ATM/Ethernet/T1-E1 WAN (CSU/DSX line-mode config, WAN-link status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the ZHONE-Wan-MIB::zhoneLoopbackConfig OID value, configure state conditions and alerts, and monitor any Zhone broadband CPE / access gateways, ATM/Ethernet/T1-E1 WAN (CSU/DSX line-mode config, WAN-link status) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.5504 | Zhone | BITSTORM-HP-160-MIB |
| 1.3.6.1.4.1.5504.5 | zhonePhysical | Zhone |
| 1.3.6.1.4.1.5504.5.2 | zhoneDsx | Zhone |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.5504.5.2.2 | zhoneDs1Table | ZHONE-Wan-MIB |
| 1.3.6.1.4.1.5504.5.2.2.1 | zhoneDs1Entry | ZHONE-Wan-MIB |
| 1.3.6.1.4.1.5504.5.2.2.1.8 | zhoneLoopbackConfig | ZHONE-Wan-MIB |