XYLAN-VLAN-MIB

All MIBs › XYLAN-VLAN-MIB

Category: Xylan OmniSwitch

Description:

Manages Xylan OmniSwitch VLAN creation, port membership, tagging, and inter-VLAN routing policies.

Imported Objects

BridgeId
MacAddress
Timeout

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks

From RFC1213-MIB

DisplayString

From XYLAN-BASE-MIB

xylanVlanArch

OBJECT-IDENTITY

From XYLAN-PORT-MIB

XylanPortFuncCodes

What Is XYLAN-VLAN-MIB?

XYLAN-VLAN-MIB is a vendor-specific MIB for Xylan (later Alcatel) OmniSwitch devices, covering Layer 2/3 VLAN management -- VLAN creation and deletion, port-to-VLAN membership, 802.1Q tagging configuration, and inter-VLAN routing policy. It sits in the switching/networking configuration category rather than pure hardware-health, exposing primarily configuration-state data about how VLANs and ports are provisioned on the switch. Its monitoring value lies in tracking configuration/software status: whether a port's VLAN assignment or tagging mode matches intended policy, and whether inter-VLAN routing is enabled as expected, which helps catch misconfiguration-driven outages rather than physical faults. It likely depends on standard BRIDGE-MIB/Q-BRIDGE-MIB concepts for VLAN semantics even though it defines Xylan-specific object names. It is deployed on Xylan/Alcatel OmniSwitch campus and enterprise LAN switches where administrators manage VLAN segmentation centrally via SNMP, often looking up a specific XYLAN-VLAN-MIB OID directly to confirm which node governs a given VLAN or port-tagging setting.

IPNetwork Monitor allows you to monitor SNMP objects defined in XYLAN-VLAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

VLAN membership
port tagging mode
VLAN creation/deletion status
inter-VLAN routing policy

Supported Devices

Xylan/Alcatel OmniSwitch campus/enterprise LAN switch (legacy VLAN configuration)

Monitoring Examples

No specific object or table names were provided for this MIB in the source data, so a concrete polling example cannot be grounded in real identifiers; based on the short description, a realistic scenario would involve polling VLAN membership and port-tagging tables to confirm a port is in its assigned VLAN and using the correct tagging mode, catching cases where a port drifts out of policy after a reconfiguration.

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT atBindRuleBindParameter	1.3.6.1.4.1.800.2.2.10.16.1.8	INTEGER	read-write	The parameters to bind together.
atBindRuleEntry	1.3.6.1.4.1.800.2.2.10.16.1		not-accessible	An entry in the Binding Rule Table.
INT atBindRuleGroupId	1.3.6.1.4.1.800.2.2.10.16.1.1	INTEGER	read-write	The group id of the vlan for which this rule is configured.
INT atBindRuleIndex	1.3.6.1.4.1.800.2.2.10.16.1.3	INTEGER	read-write	The index which uniquely identifies this rule for this vlan.
IP atBindRuleIPAddress	1.3.6.1.4.1.800.2.2.10.16.1.5	IpAddress	read-write	The IP address for which this binding is configured.
MAC atBindRuleMacAddress	1.3.6.1.4.1.800.2.2.10.16.1.6	MacAddress	read-write	The mac address for which this binding is configured.
OCT atBindRulePortId	1.3.6.1.4.1.800.2.2.10.16.1.4	OCTET STRING	read-write	The port ( slot/intf/srvc/inst) for which this binding is configured.
OCT atBindRuleProtocol	1.3.6.1.4.1.800.2.2.10.16.1.7	OCTET STRING	read-write	The protocol for which this binding is configured.
INT atBindRuleStatus	1.3.6.1.4.1.800.2.2.10.16.1.9	INTEGER	read-write	The admin status for this rule.
atBindRuleTable	1.3.6.1.4.1.800.2.2.10.16		not-accessible	The Binding Rule table.
INT atBindRuleVlanId	1.3.6.1.4.1.800.2.2.10.16.1.2	INTEGER	read-write	The vlan id for which this rule is configured.
INT atDefaultVlan	1.3.6.1.4.1.800.2.2.10.8	INTEGER	read-write	When set to on, it allows devices to be assigned to the default vlan, else if it set to off, such devices are not assigned to any vlan, thereby preventing them from communicating to other devices.
atDHCPMacRuleEntry	1.3.6.1.4.1.800.2.2.10.19.1		not-accessible	An entry in the atDHCPMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
INT atDHCPMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.19.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atDHCPMacRuleIndex	1.3.6.1.4.1.800.2.2.10.19.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
MAC atDHCPMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.19.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
INT atDHCPMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.19.1.5	INTEGER	read-write	This object determines if the MAC address is included in the VLAN definition. If the object is set to disabled, the MAC address is removed from the VLAN definition.
atDHCPMacRuleTable	1.3.6.1.4.1.800.2.2.10.19		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
INT atDHCPMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.19.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
atDHCPportRuleEntry	1.3.6.1.4.1.800.2.2.10.18.1		not-accessible	An entry in the atDHCPportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
INT atDHCPportRuleGroupId	1.3.6.1.4.1.800.2.2.10.18.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atDHCPportRuleIdx	1.3.6.1.4.1.800.2.2.10.18.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
OCT atDHCPportRulePortId	1.3.6.1.4.1.800.2.2.10.18.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
INT atDHCPportRulePortState	1.3.6.1.4.1.800.2.2.10.18.1.5	INTEGER	read-write	This object determines whether the port is being added or deleted from this port rule definition.
atDHCPportRuleTable	1.3.6.1.4.1.800.2.2.10.18		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
INT atDHCPportRuleVLANId	1.3.6.1.4.1.800.2.2.10.18.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
atMacRuleEntry	1.3.6.1.4.1.800.2.2.10.2.1		not-accessible	An entry in the atMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
INT atMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.2.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atMacRuleIndex	1.3.6.1.4.1.800.2.2.10.2.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
MAC atMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.2.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
INT atMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.2.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atMacRuleTable	1.3.6.1.4.1.800.2.2.10.2		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
INT atMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.2.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
atMcastRuleEntry	1.3.6.1.4.1.800.2.2.10.11.1		not-accessible	An entry in the MCAST Rule table.
INT atMcastRuleGroupId	1.3.6.1.4.1.800.2.2.10.11.1.1	INTEGER	read-write	The group in which this rule is defined.
INT atMcastRuleIndex	1.3.6.1.4.1.800.2.2.10.11.1.3	INTEGER	read-write	The rule index ( a vlan can have multiple rules defined ) which exactly identifies this rule.
MAC atMcastRuleMacAddress	1.3.6.1.4.1.800.2.2.10.11.1.4	MacAddress	read-write	The Multicast MAC Address that makes up this rule.
INT atMcastRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.11.1.5	INTEGER	read-write	The admin-state of this multicast mac address.
atMcastRuleTable	1.3.6.1.4.1.800.2.2.10.11		not-accessible	This table is used to configure MCAST Rules for a VLAN.
INT atMcastRuleVLANId	1.3.6.1.4.1.800.2.2.10.11.1.2	INTEGER	read-write	The VLAN for which this rule is defined.
atmcMacRuleEntry	1.3.6.1.4.1.800.2.2.10.10.1		not-accessible	An entry in the atmcMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
INT atmcMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.10.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atmcMacRuleIndex	1.3.6.1.4.1.800.2.2.10.10.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
MAC atmcMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.10.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
INT atmcMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.10.1.5	INTEGER	read-write	This object determines if the MAC address is included in the VLAN definition. If the object is set to disabled, the MAC address is removed from the VLAN definition.
atmcMacRuleTable	1.3.6.1.4.1.800.2.2.10.10		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
INT atmcMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.10.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
atmcportRuleEntry	1.3.6.1.4.1.800.2.2.10.9.1		not-accessible	An entry in the atportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
INT atmcportRuleGroupId	1.3.6.1.4.1.800.2.2.10.9.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atmcportRuleIdx	1.3.6.1.4.1.800.2.2.10.9.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
OCT atmcportRulePortId	1.3.6.1.4.1.800.2.2.10.9.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
INT atmcportRulePortState	1.3.6.1.4.1.800.2.2.10.9.1.5	INTEGER	read-write	This object determines whether the port is being added or deleted from this port rule definition.
atmcportRuleTable	1.3.6.1.4.1.800.2.2.10.9		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
INT atmcportRuleVLANId	1.3.6.1.4.1.800.2.2.10.9.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
INT atmcVLANAdminStatus	1.3.6.1.4.1.800.2.2.10.13.1.4	INTEGER	read-write	The Admin status of the VLAN. If set to disabled, any rules configured for this vlan will no longer be used and their status will be changed to disabled.
atmcVLANControlEntry	1.3.6.1.4.1.800.2.2.10.13.1		not-accessible	An entry in the control table.
atmcVLANControlTable	1.3.6.1.4.1.800.2.2.10.13		not-accessible	This table gives the control information about all Auto-Tracker VLANs.
STR atmcVLANDesc	1.3.6.1.4.1.800.2.2.10.13.1.3	DisplayString	read-write	The description for this vlan.
INT atmcVLANGroupId	1.3.6.1.4.1.800.2.2.10.13.1.1	INTEGER	read-write	This is the VLAN group to which the VLAN belongs.
INT atmcVLANId	1.3.6.1.4.1.800.2.2.10.13.1.2	INTEGER	read-write	The VLAN id for this VLAN.
INT atmcVLANOperStatus	1.3.6.1.4.1.800.2.2.10.13.1.5	INTEGER	read-only	The operation status of this vlan. If there any devices learnt by this system on this vlan, the operation status of the vlan is said to be active.
INT atmcVLANRuleIndex	1.3.6.1.4.1.800.2.2.10.12.1.3	INTEGER	read-only	The exact rule identifier for this rule.
INT atmcVLANRuleSubIndex	1.3.6.1.4.1.800.2.2.10.12.1.4	INTEGER	read-only	In case a VLAN is defined using multiple instances of the same type of rule, this object identifies the exact instance of that type of rule. This object could then be used along with the group and vlanid to get the complete definition of this rule from the appropriate rule table.
atmcVLANRuleSumEntry	1.3.6.1.4.1.800.2.2.10.12.1		not-accessible	An entry in the vlan summary table.
INT atmcVLANRuleSumGroupId	1.3.6.1.4.1.800.2.2.10.12.1.1	INTEGER	read-only	The group to which the VLAN belongs.
atmcVLANRuleSumTable	1.3.6.1.4.1.800.2.2.10.12		not-accessible	This table provides the summary of vlan rule configuration.
INT atmcVLANRuleSumVLANId	1.3.6.1.4.1.800.2.2.10.12.1.2	INTEGER	read-only	The VLAN Id for this rule is defined.
INT atmcVLANRuleType	1.3.6.1.4.1.800.2.2.10.12.1.5	INTEGER	read-only	The type of rule. This object can then be used to decide which table to lookup for the complete definition of the rule.
atNetRuleEntry	1.3.6.1.4.1.800.2.2.10.4.1		not-accessible	An entry in the atNetRuleTable. A VLAN can be defined using exaclty one address only except in the case of IPX where it could either be a Network number or the encapsulation.
INT atNetRuleGroupId	1.3.6.1.4.1.800.2.2.10.4.1.1	INTEGER	read-write	This object indicates the VLAN Group in which this VLAN is defined.
INT atNetRuleIndex	1.3.6.1.4.1.800.2.2.10.4.1.3	INTEGER	read-write	This object specifies the exact Network Address rule for this VLAN. When creating a VLAN using the Network Address rule, this object must be set to 0.
OCT atNetRuleNetAddr	1.3.6.1.4.1.800.2.2.10.4.1.5	OCTET STRING	read-write	This object gives the network address that defines this vlan. If the protocol is IP, this object contains the four bytes of IP address followed by four bytes of IP Subnet Mask. If the protocol is IPX, this object contains the four bytes of Network Number followed by one byte of encapsulation type used on that network. The values for the encapsulation types are: byte 5 = 1 - IPX 802.3 encapsulation byte 5 = 2 - IPX Ethernet2 encapsulation byte 5 = 3 - IPX LLC encapsulation byte 5 = 4 - IPX SNAP encapsulation If the protocol is DECNet, this object contains the one byte of DEC area.
INT atNetRuleProtocolId	1.3.6.1.4.1.800.2.2.10.4.1.4	INTEGER	read-write	This object indicates which protocols Network Address is used to define this VLAN.
INT atNetRuleStatus	1.3.6.1.4.1.800.2.2.10.4.1.6	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atNetRuleTable	1.3.6.1.4.1.800.2.2.10.4		not-accessible	This table is used to configure an Auto-Tracker VLAN based on Net Addr Rule. Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
INT atNetRuleVLANId	1.3.6.1.4.1.800.2.2.10.4.1.2	INTEGER	read-write	This object is the VLAN Id for this NetAddr-rule based vlan.
atportRuleEntry	1.3.6.1.4.1.800.2.2.10.1.1		not-accessible	An entry in the atportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
INT atportRuleGroupId	1.3.6.1.4.1.800.2.2.10.1.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atportRuleIdx	1.3.6.1.4.1.800.2.2.10.1.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
OCT atportRulePortId	1.3.6.1.4.1.800.2.2.10.1.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
INT atportRulePortState	1.3.6.1.4.1.800.2.2.10.1.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atportRuleTable	1.3.6.1.4.1.800.2.2.10.1		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
INT atportRuleVLANId	1.3.6.1.4.1.800.2.2.10.1.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
OCT atProtoRule	1.3.6.1.4.1.800.2.2.10.3.1.4	OCTET STRING	read-write	This object is an octet string of length 5 bytes. This object specifies the protocol type that defines this vlan. The values for the different protocols are: IP - first byte = 1, IPX - first byte = 2, AppleTalk - first byte = 3, DECNet - first byte = 4, Note that, in case of IP, ARP is included as IP and need not be specified explicitly. Similarly when AppleTalk is chosen both DDP and AARP are included. If any other protocol is used, it can be defined either by using Ether-type - first byte = 5 specifying its ether-type, second and third byte = ether-type value in hex. DSAP and SSAP - first byte = 6 specifying that its SAP type second byte = DSAP, third byte = SSAP in hex. SNAP Type - first byte = 7 specifying its SNAP second through sixth byte = snap value in hex.
atProtoRuleEntry	1.3.6.1.4.1.800.2.2.10.3.1		not-accessible	An entry in the atProtoRuleTable.
INT atProtoRuleGroupId	1.3.6.1.4.1.800.2.2.10.3.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is defined.
INT atProtoRuleIndex	1.3.6.1.4.1.800.2.2.10.3.1.3	INTEGER	read-write	This object specifies the exact protocol rule for this VLAN. On creating a VLAN based on protocol rule, this object must be set to 0.
INT atProtoRuleStatus	1.3.6.1.4.1.800.2.2.10.3.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atProtoRuleTable	1.3.6.1.4.1.800.2.2.10.3		not-accessible	This table is used to configure an Auto-Tracker VLAN based on Protocol Rule. Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
INT atProtoRuleVLANId	1.3.6.1.4.1.800.2.2.10.3.1.2	INTEGER	read-write	This object is the VLAN Id defined by this Protocol-rule.
atUserRuleEntry	1.3.6.1.4.1.800.2.2.10.5.1		not-accessible	An entry in the atUserRuleTable. A VLAN can be defined by more than one rule. In that case, the device will belong to that VLAN if it matches atleast one of the rules defined for that VLAN.
INT atUserRuleGroupId	1.3.6.1.4.1.800.2.2.10.5.1.1	INTEGER	read-write	This object indicates the VLAN Group in which this VLAN is defined.
INT atUserRuleIndex	1.3.6.1.4.1.800.2.2.10.5.1.3	INTEGER	read-write	This object indicates the exact User defined rule for this VLAN. When creating a VLAN using the user defined rules, this object must be set to 0.
OCT atUserRuleMask	1.3.6.1.4.1.800.2.2.10.5.1.6	OCTET STRING	read-write	This object defines the mask for the pattern to match. The Mask can be upto 8 bytes long but has to be of the same length as the Value.
INT atUserRuleOffset	1.3.6.1.4.1.800.2.2.10.5.1.4	INTEGER	read-write	This object defines the offset into a frame where the pattern to match is located. This offset is relative to the start of the MAC header.
INT atUserRuleStatus	1.3.6.1.4.1.800.2.2.10.5.1.7	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atUserRuleTable	1.3.6.1.4.1.800.2.2.10.5		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a User Defined Rule.Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
OCT atUserRuleValue	1.3.6.1.4.1.800.2.2.10.5.1.5	OCTET STRING	read-write	This object defines the value of the pattern to match in a frame. The maximum length of this value can be 8 octets and the associated mask should have the same length as this object.
INT atUserRuleVLANId	1.3.6.1.4.1.800.2.2.10.5.1.2	INTEGER	read-write	This object is the VLAN Id for this User-rule based vlan.
XYL atvIPRouterAdmStatus	1.3.6.1.4.1.800.2.2.11.1.1.8	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enable(2) or disable(1) (or delete (3)) upon user's request.
IP atvIPRouterBcastAddress	1.3.6.1.4.1.800.2.2.11.1.1.6	IpAddress	read-write	The IP broadcast address for this virtual bridge instance for the purpose of allowing access from the external network management system.
STR atvIPRouterDescription	1.3.6.1.4.1.800.2.2.11.1.1.7	DisplayString	read-write	Textual description of the router instance.
atvIPRouterEntry	1.3.6.1.4.1.800.2.2.11.1.1		not-accessible	A VLAN entry.
INT atvIPRouterFramingType	1.3.6.1.4.1.800.2.2.11.1.1.10	INTEGER	read-write	Provides the ability to set the outbound frame type for IP traffic. The default frame type is Ethernet 2. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
atvIPRouterInfo	1.3.6.1.4.1.800.2.2.11
IP atvIPRouterNetAddress	1.3.6.1.4.1.800.2.2.11.1.1.4	IpAddress	read-write	The IP network address for this virtual bridge instance for the purpose of allowing access from the external network management system.
XYL atvIPRouterOperStatus	1.3.6.1.4.1.800.2.2.11.1.1.9	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
OCT atvIPRouterProtocol	1.3.6.1.4.1.800.2.2.11.1.1.3	OCTET STRING	read-write	The routing protocol(s) for this virtual router port. Each IP router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipOther(1), ipRip(2), ipEgp(4), ipGgp(8), ipHello(16), ipIs-is(32), ipEs-is(64), ipCiscoIgrp(128), ipBbnSpfIgp(256), ipOigp(512)
INT atvIPRouterRelayServicesFwd	1.3.6.1.4.1.800.2.2.11.1.1.12	INTEGER	read-write	Each of the 8 least significant bits are assigned to a UDP Relay service as follows: 01H - bootp (Not currently allowed) 02H - NBNS 04H - NBDD 08H - Gen1 10H - Gen2 20H - Gen3 40H - Gen4 80H - Gen5 A set bit indicates that packets are being forwarded to this vlan for the service corresponding to the bit. Use bit 15 to indicate that a UDP Relay Service should be unset and packets should not be forwarded to this vlan. 8001H - bootp (Not currently allowed) 8002H - NBNS 8004H - NBDD 8008H - Gen1 8010H - Gen2 8020H - Gen3 8040H - Gen4 8080H - Gen5
INT atvIPRouterRipConfigMode	1.3.6.1.4.1.800.2.2.11.1.1.11	INTEGER	read-write	RIP's operational mode. 'silent' means that RIP listens for routing updates but does not send them. 'deaf' means that RIP sends routing updates but not listen to them. 'active' means that RIP both sends and receives routing updates, and 'inactive' means that RIP is not operational on the given virtual LAN. The default is 'simple'.
IP atvIPRouterSubNetMask	1.3.6.1.4.1.800.2.2.11.1.1.5	IpAddress	read-write	The IP network subnet mask for this virtual bridge instance for the purpose of allowing access from the external network management system.
atvIPRouterTable	1.3.6.1.4.1.800.2.2.11.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
INT atvIPRouterVLan	1.3.6.1.4.1.800.2.2.11.1.1.2	INTEGER	read-write	Auto Tracker VLAN Id for this router port instance.
INT atvIPRouterVLanGroup	1.3.6.1.4.1.800.2.2.11.1.1.1	INTEGER	read-write	VLAN Group ID for this atvIPRouterEntry instance.
XYL atvIPXRouterAdmStatus	1.3.6.1.4.1.800.2.2.12.1.1.7	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enabled(2) or disabled(1) upon user's request.
STR atvIPXRouterDescription	1.3.6.1.4.1.800.2.2.12.1.1.6	DisplayString	read-write	Textual description of the router instance.
atvIPXRouterEntry	1.3.6.1.4.1.800.2.2.12.1.1		not-accessible	A VLAN entry.
INT atvIPXRouterFramingType	1.3.6.1.4.1.800.2.2.12.1.1.5	INTEGER	read-write	Provides the ability to set the outbound frame type for IPX traffic. The default frame type is 802.2 Novell Raw. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
atvIPXRouterInfo	1.3.6.1.4.1.800.2.2.12
NET atvIPXRouterNetAddress	1.3.6.1.4.1.800.2.2.12.1.1.4	NetNumber	read-write	The IPX network address for this virtual bridge.
XYL atvIPXRouterOperStatus	1.3.6.1.4.1.800.2.2.12.1.1.8	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
INT atvIPXRouterProtocol	1.3.6.1.4.1.800.2.2.12.1.1.3	INTEGER	read-write	The routing protocol(s) for this virtual router port. Each IPX router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipxOther(1), ipxRip(2), ipxSap(4)
atvIPXRouterTable	1.3.6.1.4.1.800.2.2.12.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
INT atvIPXRouterVLan	1.3.6.1.4.1.800.2.2.12.1.1.2	INTEGER	read-write	VLAN ID for this vIPXRouterEntry instance.
INT atvIPXRouterVLanGroup	1.3.6.1.4.1.800.2.2.12.1.1.1	INTEGER	read-write	VLAN Group ID for this vIPXRouterEntry instance.
INT atvIPXSrcRteType	1.3.6.1.4.1.800.2.2.12.1.1.9	INTEGER	read-write	Provide the ability to set the type of source routing broadcasts between AllRoutesExplorer(0) and SpanningTreeExplorer(1).
INT atVLANAdminStatus	1.3.6.1.4.1.800.2.2.10.7.1.4	INTEGER	read-write	The Admin status of the VLAN. If set to disabled, any rules configured for this vlan will no longer be used and their status will be changed to disabled.
atVLANControlEntry	1.3.6.1.4.1.800.2.2.10.7.1		not-accessible	An entry in the control table.
atVLANControlTable	1.3.6.1.4.1.800.2.2.10.7		not-accessible	This table gives the control information about all Auto-Tracker VLANs.
STR atVLANDesc	1.3.6.1.4.1.800.2.2.10.7.1.3	DisplayString	read-write	The description for this vlan.
INT atVLANGroupId	1.3.6.1.4.1.800.2.2.10.7.1.1	INTEGER	read-write	This is the VLAN group to which the VLAN belongs.
INT atVLANId	1.3.6.1.4.1.800.2.2.10.7.1.2	INTEGER	read-write	The VLAN id for this VLAN.
INT atVLANOperStatus	1.3.6.1.4.1.800.2.2.10.7.1.5	INTEGER	read-only	The operation status of this vlan. If there any devices learnt by this system on this vlan, the operation status of the vlan is said to be active.
INT atVLANRuleIndex	1.3.6.1.4.1.800.2.2.10.6.1.3	INTEGER	read-only	The exact rule identifier for this rule.
INT atVLANRuleSubIndex	1.3.6.1.4.1.800.2.2.10.6.1.4	INTEGER	read-only	In case a VLAN is defined using multiple instances of the same type of rule, this object identifies the exact instance of that type of rule. This object could then be used along with the group and vlanid to get the complete definition of this rule from the appropriate rule table.
atVLANRuleSumEntry	1.3.6.1.4.1.800.2.2.10.6.1		not-accessible	An entry in the vlan summary table.
INT atVLANRuleSumGroupId	1.3.6.1.4.1.800.2.2.10.6.1.1	INTEGER	read-only	The group to which the VLAN belongs.
atVLANRuleSumTable	1.3.6.1.4.1.800.2.2.10.6		not-accessible	This table provides the summary of vlan rule configuration.
INT atVLANRuleSumVLANId	1.3.6.1.4.1.800.2.2.10.6.1.2	INTEGER	read-only	The VLAN Id for this rule is defined.
INT atVLANRuleType	1.3.6.1.4.1.800.2.2.10.6.1.5	INTEGER	read-only	The type of rule. This object can then be used to decide which table to lookup for the complete definition of the rule.
INT gmAutoServiceActivePort	1.3.6.1.4.1.800.2.2.10.14.1.12	INTEGER	read-only	Physical Port on the which the service is currently active.
INT gmAutoServiceActiveSlot	1.3.6.1.4.1.800.2.2.10.14.1.11	INTEGER	read-only	Slot on the which the service is currently active.
INT gmAutoServiceAdminState	1.3.6.1.4.1.800.2.2.10.14.1.9	INTEGER	read-write	The admin state of this service
gmAutoServiceEntry	1.3.6.1.4.1.800.2.2.10.14.1		not-accessible	an entry in the table
INT gmAutoServiceGroupId	1.3.6.1.4.1.800.2.2.10.14.1.1	INTEGER	read-write	Group for which this service is configured
INT gmAutoServiceIndex	1.3.6.1.4.1.800.2.2.10.14.1.4	INTEGER	read-write	Service index associated with this service
STR gmAutoServiceName	1.3.6.1.4.1.800.2.2.10.14.1.6	DisplayString	read-write	The name of the service. In case of LANE, this is the elan name.
INT gmAutoServiceNumber	1.3.6.1.4.1.800.2.2.10.14.1.13	INTEGER	read-only	Service number assigned by the switch when this service is activated.
INT gmAutoServiceOperState	1.3.6.1.4.1.800.2.2.10.14.1.10	INTEGER	read-write	Operational state of this service.
INT gmAutoServicePrimaryPort	1.3.6.1.4.1.800.2.2.10.14.1.3	INTEGER	read-write	Primary port on which this service will be activated.
INT gmAutoServicePrimarySlot	1.3.6.1.4.1.800.2.2.10.14.1.2	INTEGER	read-write	Primary slot on which this service will be activated.
INT gmAutoServiceSecondaryPort	1.3.6.1.4.1.800.2.2.10.14.1.8	INTEGER	read-write	Secondary port on which this service will be activated.
INT gmAutoServiceSecondarySlot	1.3.6.1.4.1.800.2.2.10.14.1.7	INTEGER	read-write	Secondary slot on which this service will be activated.
gmAutoServiceTable	1.3.6.1.4.1.800.2.2.10.14		not-accessible	Table of Auto-Activated Services
INT gmAutoServiceTranslations	1.3.6.1.4.1.800.2.2.10.14.1.14	INTEGER	read-write	This parameter controls whether frame translations will be exercised for this lane service once activated.
INT gmAutoServiceType	1.3.6.1.4.1.800.2.2.10.14.1.5	INTEGER	read-write	Type of this service - currently only lane is supported and this object should have a value of 1.
INT gmDefGroup	1.3.6.1.4.1.800.2.2.10.22	INTEGER	read-write	When this object is set to on, the switch will assign the port's default group id to all such devices which are learned and do not match any policies for mobile groups. If it is set to off, such devices will get assigned to no groups and the traffic they send will be discarded by the switch.
gmGroupListEntry	1.3.6.1.4.1.800.2.2.10.17.1		not-accessible	An entry in the Group List table.
INT gmGroupListGroupId	1.3.6.1.4.1.800.2.2.10.17.1.3	INTEGER	read-only	One of the Groups to which the port belongs.
INT gmGroupListPortInterface	1.3.6.1.4.1.800.2.2.10.17.1.2	INTEGER	read-only	The physical port number for which the group list is requested.
INT gmGroupListPortSlot	1.3.6.1.4.1.800.2.2.10.17.1.1	INTEGER	read-only	The slot id of the port for which the group list is requested.
gmGroupListTable	1.3.6.1.4.1.800.2.2.10.17		not-accessible	This table lists the groups on a port.
INT gmMoveToDefGroup	1.3.6.1.4.1.800.2.2.10.21	INTEGER	read-write	When this object is set on, the switch will remove the port of out of a mobile group when the last device in that group learnt on that port ages out due to inactivity. When it is set to off, the port will remain in such a group, even if all macs leant on that port in that group age out.
INT groupMobilityStatus	1.3.6.1.4.1.800.2.2.10.20	INTEGER	read-write	This object can used to configure the global status of group-mobility feature on the switch.
INT pMapConfigId	1.3.6.1.4.1.800.2.2.17.3.1.1	INTEGER	read-only	A unique number that identifies this Port Mapping with the physical OmniSwitch or OSR.
INT pMapConfigStatus	1.3.6.1.4.1.800.2.2.17.3.1.2	INTEGER	read-write	This object indicates whether to set (1) or delete (2) the port mapping configeration..
INT pMapEgressAdminStatus	1.3.6.1.4.1.800.2.2.17.2.1.6	INTEGER	read-write	This object indicates whether to add(1) to or delete(2) from the Port Mapping Egress Port.
INT pMapEgressId	1.3.6.1.4.1.800.2.2.17.2.1.1	INTEGER	read-write	A unique number that identifies this Port Mapping on the physical OmniSwitch or OSR.
INT pMapEgressInst	1.3.6.1.4.1.800.2.2.17.2.1.5	INTEGER	read-write	A Instance that is associated with this Port Mapping Egress Port.
INT pMapEgressPort	1.3.6.1.4.1.800.2.2.17.2.1.3	INTEGER	read-write	A physical port number that is associated with the Port Mapping Egress Port.
INT pMapEgressSlot	1.3.6.1.4.1.800.2.2.17.2.1.2	INTEGER	read-write	A physical slot number on whitch the Port Mapping Egress Port is configured.
INT pMapEgressSrvc	1.3.6.1.4.1.800.2.2.17.2.1.4	INTEGER	read-write	A service type that is associated with this Port Mapping Egress Port.
INT pMapIngressAdminStatus	1.3.6.1.4.1.800.2.2.17.1.1.6	INTEGER	read-write	This object indicates whether to add(1) to or delete(2) from the Port Mapping Ingress List.
INT pMapIngressId	1.3.6.1.4.1.800.2.2.17.1.1.1	INTEGER	read-write	A unique number that identifies this Port Mapping on the OmniSwitch or OSR.
INT pMapIngressInst	1.3.6.1.4.1.800.2.2.17.1.1.5	INTEGER	read-write	A Instance that is associated with this Port Mapping Ingress Port.
INT pMapIngressPort	1.3.6.1.4.1.800.2.2.17.1.1.3	INTEGER	read-write	A physical port number that is associated with the Port Mapping Ingress Port.
INT pMapIngressSlot	1.3.6.1.4.1.800.2.2.17.1.1.2	INTEGER	read-write	A physical slot number on which the Port Mapping Ingress Port is configured.
INT pMapIngressSrvc	1.3.6.1.4.1.800.2.2.17.1.1.4	INTEGER	read-write	A service type that is associated with this Port Mapping Ingress Port.
INT qGroupAdminStatus	1.3.6.1.4.1.800.2.2.15.1.1.8	INTEGER	read-write	Value of 0 indicates the service should be deleted, value of 1 indicates the service should be created.
STR qGroupDescription	1.3.6.1.4.1.800.2.2.15.1.1.5	DisplayString	read-write	Textual description of multiple spanning tree.
qGroupEntry	1.3.6.1.4.1.800.2.2.15.1.1		not-accessible	An entry in 802.1q group table.
INT qGroupGroupId	1.3.6.1.4.1.800.2.2.15.1.1.3	INTEGER	read-write	Group Id on the particular port.
INT qGroupMode	1.3.6.1.4.1.800.2.2.15.1.1.4	INTEGER	read-write	gstsxylan(1) indicates spanning tree support on a gigabit port by proprietary mode and gstsieee(2) indicates spanning tree on a gigabit port by IEEE mode, msts(3) indicates multiple spanning tree support on a 10/100 Mammoth Ethernet port, and ssts(4) indicates single spanning tree support on a 10/100 Mammoth Ethernet port.
INT qGroupPort	1.3.6.1.4.1.800.2.2.15.1.1.2	INTEGER	read-write	The physical port number.
INT qGroupPriority	1.3.6.1.4.1.800.2.2.15.1.1.7	INTEGER	read-write	Priority used for support multiple spanning tree.
CTR qGroupRxOctets	1.3.6.1.4.1.800.2.2.15.1.1.12	Counter	read-only	Gives the number of received bytes.
CTR qGroupRxPkts	1.3.6.1.4.1.800.2.2.15.1.1.10	Counter	read-only	Gives the number of received packets.
INT qGroupSlot	1.3.6.1.4.1.800.2.2.15.1.1.1	INTEGER	read-write	The slot id of the required port.
qGroupTable	1.3.6.1.4.1.800.2.2.15.1		not-accessible	This table lists the 802.1q groups on a port.
INT qGroupTag	1.3.6.1.4.1.800.2.2.15.1.1.6	INTEGER	read-write	Tag used for support multiple spanning tree.
CTR qGroupTxOctets	1.3.6.1.4.1.800.2.2.15.1.1.11	Counter	read-only	Gives the number of transmitted bytes.
CTR qGroupTxPkts	1.3.6.1.4.1.800.2.2.15.1.1.9	Counter	read-only	Gives the number of transmitteded packets.
v80210	1.3.6.1.4.1.800.2.2.13
INT v80210Command	1.3.6.1.4.1.800.2.2.13.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given 80210 service.
INT v80210LanNumber	1.3.6.1.4.1.800.2.2.13.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given 80210 service.
INT v80210ServicesBridgeID	1.3.6.1.4.1.800.2.2.13.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given 80210 service. A value of 0 means that the Virtual Bridge port does not exist.
STR v80210ServicesDescription	1.3.6.1.4.1.800.2.2.13.1.1.3	DisplayString	read-write	A description of the 80210 service being provided.
v80210ServicesEntry	1.3.6.1.4.1.800.2.2.13.1.1		not-accessible	A 80210 services entry.
INT v80210ServicesSlot	1.3.6.1.4.1.800.2.2.13.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the 80210 service.
INT v80210ServicesStation	1.3.6.1.4.1.800.2.2.13.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the 80210 service.
v80210ServicesTable	1.3.6.1.4.1.800.2.2.13.1		not-accessible	A list of commands to add or remove Virtual LANs from a 80210 service.
INT v80210Slot	1.3.6.1.4.1.800.2.2.13.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the 80210 service.
INT v80210Station	1.3.6.1.4.1.800.2.2.13.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the 80210 service.
v80210VlanEntry	1.3.6.1.4.1.800.2.2.13.2.1		not-accessible	A 80210trunking Virtual LAN entry.
v80210VlanTable	1.3.6.1.4.1.800.2.2.13.2		not-accessible	A list of commands to add or remove Virtual LANs from a 80210 service.
v8021Q	1.3.6.1.4.1.800.2.2.15
vAutoTracker	1.3.6.1.4.1.800.2.2.10
vBrdgInfo	1.3.6.1.4.1.800.2.2.4
MAC vBrdgStaticAddress	1.3.6.1.4.1.800.2.2.4.4.1.1	MacAddress	read-write	The MAC address which the static status applies.
vBrdgStaticEntry	1.3.6.1.4.1.800.2.2.4.4.1		not-accessible	Information about a specific unicast MAC address for which the VLAN bridge has VLAN information.
XYL vBrdgStaticPortFuncTyp	1.3.6.1.4.1.800.2.2.4.4.1.4	XylanPortFuncCodes	read-write	The service type of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortIF and vBrdgStaticPortFuncTypInst must also be set.
INT vBrdgStaticPortFuncTypInst	1.3.6.1.4.1.800.2.2.4.4.1.5	INTEGER	read-write	The service type instance of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortIF and vBrdgStaticPortFuncTyp must also be set.
INT vBrdgStaticPortIF	1.3.6.1.4.1.800.2.2.4.4.1.3	INTEGER	read-write	The on-board interface of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortFuncTyp and vBrdgStaticPortFuncTypInst must also be set.
INT vBrdgStaticPortSlot	1.3.6.1.4.1.800.2.2.4.4.1.2	INTEGER	read-write	The slot number of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is provided, vBrdgStaticPortIF, vBrdgStaticPortFuncTyp and vBrdgStaticPortFuncTypInst must also be set.
INT vBrdgStaticStatus	1.3.6.1.4.1.800.2.2.4.4.1.6	INTEGER	read-write	This object indicates the status of this entry. Xylan does not support other(1). The default value is permenent(3). invalid(2) - writing this value to the object removes the entry. permanent(3) - this entry will never age out and remain even after next reset. deleteOnReset(4) - this entry will not age out until reset. deleteOnTimeout(5) - write this value to the entry will cause it to age out.
vBrdgStaticTable	1.3.6.1.4.1.800.2.2.4.4		not-accessible	A table contains source addresses which can be configured to stay permanent (not aging out) in the Forwarding table.
INT vBrdgTpAgingTime	1.3.6.1.4.1.800.2.2.4.2	INTEGER	read-write	The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
INT vBrdgTpATVLANAgeingTime	1.3.6.1.4.1.800.2.2.4.5	INTEGER	read-write	The AutoTracker extended ageing timer. This value indicates how long the switch will remember the mac address and its associated vlan information. The default value is 1200 secs. This means that the mac information will be remembered for (vBrdgTpATVLANAgeingTime - vBrdgTpAgingTime) seconds after the mac is aged out. This value must be set to a value greater than or equal to vBrdgTpAgingTime.
MAC vBrdgTpFdbAddress	1.3.6.1.4.1.800.2.2.4.3.1.2	MacAddress	read-only	A unicast MAC address for which the VLAN bridge has forwarding and/or filtering information.
INT vBrdgTpFdbDupStatus	1.3.6.1.4.1.800.2.2.4.3.1.9	INTEGER	read-only	The variable indicates if vBrdgTpFdbAddress is a duplicate Mac.
vBrdgTpFdbEntry	1.3.6.1.4.1.800.2.2.4.3.1		not-accessible	Information about a specific unicast MAC address for which the VLAN bridge has some forwarding and/or filtering information.
INT vBrdgTpFdbGroupId	1.3.6.1.4.1.800.2.2.4.3.1.1	INTEGER	read-only	The GroupId for this bridge.
CTR vBrdgTpFdbLastSeenTime	1.3.6.1.4.1.800.2.2.4.3.1.10	Counter	read-only	The time since, the specific unicast MAC address for which the VLAN bridge has forwarding information was last seen.
XYL vBrdgTpFdbRcvPortFuncTyp	1.3.6.1.4.1.800.2.2.4.3.1.5	XylanPortFuncCodes	read-only	The service type of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvPortFuncTypInst	1.3.6.1.4.1.800.2.2.4.3.1.6	INTEGER	read-only	The service type instance of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvPortIF	1.3.6.1.4.1.800.2.2.4.3.1.4	INTEGER	read-only	The on-board interface number of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvPortSlot	1.3.6.1.4.1.800.2.2.4.3.1.3	INTEGER	read-only	The slot number of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvStatus	1.3.6.1.4.1.800.2.2.4.3.1.7	INTEGER	read-only	The status of this entry. Xylan does not support other(1) and self(4). The meanings of the values are: invalid(2) : this entry is no longer valid, but has not yet been flushed from the table. learned(3) : this entry has been learned. mgmt(5) : this entry is configured as a static entry.
INT vBrdgTpFdbRcvVLANMembership	1.3.6.1.4.1.800.2.2.4.3.1.8	INTEGER	read-only	The Auto-Tracker VLAN membership for this device. Each bit that is set in this objects 32 bit value indicates that the device is part of the VLAN given by that bits position.
vBrdgTpFdbTable	1.3.6.1.4.1.800.2.2.4.3		not-accessible	A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function within its VLAN in determining how to propagate a received frame.
CTR vBrdgTpLearnEntryDiscards	1.3.6.1.4.1.800.2.2.4.1	Counter	read-only	The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
vDBr	1.3.6.1.4.1.800.2.2.14
INT vDBrCommand	1.3.6.1.4.1.800.2.2.14.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given DBr service.
INT vDBrLanNumber	1.3.6.1.4.1.800.2.2.14.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given DBr service.
INT vDBrServicesBridgeID	1.3.6.1.4.1.800.2.2.14.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given DBr service. A value of 0 means that the Virtual Bridge port does not exist.
STR vDBrServicesDescription	1.3.6.1.4.1.800.2.2.14.1.1.3	DisplayString	read-write	A description of the DBr service being provided.
vDBrServicesEntry	1.3.6.1.4.1.800.2.2.14.1.1		not-accessible	An DBr services entry.
INT vDBrServicesSlot	1.3.6.1.4.1.800.2.2.14.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the DBr service.
INT vDBrServicesStation	1.3.6.1.4.1.800.2.2.14.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the DBr service.
vDBrServicesTable	1.3.6.1.4.1.800.2.2.14.1		not-accessible	A list of commands to add or remove Virtual LANs from an DBr service.
INT vDBrSlot	1.3.6.1.4.1.800.2.2.14.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the DBr service.
INT vDBrStation	1.3.6.1.4.1.800.2.2.14.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the DBr service.
vDBrVlanEntry	1.3.6.1.4.1.800.2.2.14.2.1		not-accessible	An DBr trunking Virtual LAN entry.
vDBrVlanTable	1.3.6.1.4.1.800.2.2.14.2		not-accessible	A list of commands to add or remove Virtual LANs from the DBr service.
vDupMac	1.3.6.1.4.1.800.2.2.16
INT vDupMacIntf	1.3.6.1.4.1.800.2.2.16.3	INTEGER	read-only	The interface number (1-based) where duplicate MAC address was last received.
MAC vDupMacMac	1.3.6.1.4.1.800.2.2.16.1	MacAddress	read-only	The router port's MAC address for which the last duplicate MAC address was detected .
INT vDupMacSlot	1.3.6.1.4.1.800.2.2.16.2	INTEGER	read-only	The slot number (1-based) where duplicate MAC address was last received.
INT vDupMacTime	1.3.6.1.4.1.800.2.2.16.4	INTEGER	read-only	The time in seconds that the duplicate MAC address was detected.
XYL vIPRouterAdmStatus	1.3.6.1.4.1.800.2.2.2.1.1.7	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enable(2) or disable(1) (or delete (3)) upon user's request.
IP vIPRouterBcastAddress	1.3.6.1.4.1.800.2.2.2.1.1.5	IpAddress	read-write	The IP broadcast address for this virtual bridge instance for the purpose of allowing access from the external network management system.
STR vIPRouterDescription	1.3.6.1.4.1.800.2.2.2.1.1.6	DisplayString	read-write	Textual description of the router instance.
vIPRouterEntry	1.3.6.1.4.1.800.2.2.2.1.1		not-accessible	A VLAN entry.
INT vIPRouterFramingType	1.3.6.1.4.1.800.2.2.2.1.1.9	INTEGER	read-write	Provides the ability to set the outbound frame type for IP traffic. The default frame type is Ethernet 2. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
vIPRouterInfo	1.3.6.1.4.1.800.2.2.2
IP vIPRouterNetAddress	1.3.6.1.4.1.800.2.2.2.1.1.3	IpAddress	read-write	The IP network address for this virtual bridge instance for the purpose of allowing access from the external network management system.
XYL vIPRouterOperStatus	1.3.6.1.4.1.800.2.2.2.1.1.8	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
OCT vIPRouterProtocol	1.3.6.1.4.1.800.2.2.2.1.1.2	OCTET STRING	read-write	The routing protocol(s) for this virtual router port. Each IP router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipOther(1), ipRip(2), ipEgp(4), ipGgp(8), ipHello(16), ipIs-is(32), ipEs-is(64), ipCiscoIgrp(128), ipBbnSpfIgp(256), ipOigp(512)
STR vIPRouterRelayDescription	1.3.6.1.4.1.800.2.2.2.2.1.6	DisplayString	read-write	This sets the service description for generic services. For other services, the description is fixed and may only be read.
vIPRouterRelayEntry	1.3.6.1.4.1.800.2.2.2.2.1		not-accessible	A UDP Relay Service entry.
INT vIPRouterRelayMode	1.3.6.1.4.1.800.2.2.2.2.1.2	INTEGER	read-write	This controls whether the internal UDP Relay service is enabled or disabled. When enabled, the service will forward packets to a specified server (or specified broadcast address.) or VLAN. Note that for BOOTP/DHCP service, unless the relay's next hop ip address (vIPRouterRelayForwAddr) is set to a valid value, it will not possible to enable the relay. For other services, a VLAN to forwared to (vIPRouterRelayForwVlan in vIPRouterRelayForwTable) or a next hop ip address must be set. The mode definitions are as follows: 1 - enabled 2 - configureRequest 3 - underConfiguration 4 - disabled A manager will set the state to configureRequest(2) before attempting to configure any other parameters for a particular UPD Service. The agent will then set the state to underConfiguration(3). When in the underConfiguration(3) state, a UDP service is not completely configured and will remain in this state until the management station is finished configuring and sets the state to either enabled(1) or disabled(4). A manager is restricted to changing the state of an entry in the following ways: config under To: valid Request config invalid From: valid OK NO OK OK configRequest N/A N/A N/A N/A underConfig OK NO OK OK invalid NO OK NO OK
IP vIPRouterRelayNextHop	1.3.6.1.4.1.800.2.2.2.2.1.3	IpAddress	read-write	This sets the relay's forwarding address. It can either be set to a distinct IP address (e.g. the address of a server), to an IP broadcast address or a VLAN.
INT vIPRouterRelayParam1	1.3.6.1.4.1.800.2.2.2.2.1.4	INTEGER	read-write	This sets the BOOTP/DHCP relay's maximum hops forwarding limit. If a BOOT/DHCP frame arrives with hopcount greater than or equal to vIPRouterRelayParam1, it will be dropped. For BOOTP/DHCP the legal range is 1..16. For Generic services, this sets the port number to be forwarded. The legal range is -1..65535 with -1 indicating the unset state.
INT vIPRouterRelayParam2	1.3.6.1.4.1.800.2.2.2.2.1.5	INTEGER	read-write	This sets the BOOTP/DHCP relay's forwarding delay and is only used by the BOOTP/DHCP service. For other services it is ignored. It is typically set as seconds, but the value is totally client dependent. The relay will not forward frames until client frames have 'secs' field set to at least the value of vIPRouterRelayParam2.
VIP vIPRouterRelayService	1.3.6.1.4.1.800.2.2.2.2.1.1	VIPRouterRelayServType	read-only	This specifies the UDP Relay Service to be forwarded.
vIPRouterRelayTable	1.3.6.1.4.1.800.2.2.2.2		not-accessible	A list of UDP Relay Service instances.
INT vIPRouterRipConfigMode	1.3.6.1.4.1.800.2.2.2.1.1.10	INTEGER	read-write	RIP's operational mode. 'silent' means that RIP listens for routing updates but does not send them. 'deaf' means that RIP sends routing updates but not listen to them. 'active' means that RIP both sends and receives routing updates, and 'inactive' means that RIP is not operational on the given virtual LAN. The default is 'simple'.
IP vIPRouterSubNetMask	1.3.6.1.4.1.800.2.2.2.1.1.4	IpAddress	read-write	The IP network subnet mask for this virtual bridge instance for the purpose of allowing access from the external network management system.
vIPRouterTable	1.3.6.1.4.1.800.2.2.2.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
INT vIPRouterVLan	1.3.6.1.4.1.800.2.2.2.1.1.1	INTEGER	read-write	VLAN ID for this vIPRouterEntry instance.
XYL vIPXRouterAdmStatus	1.3.6.1.4.1.800.2.2.3.1.1.6	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enabled(2) or disabled(1) upon user's request.
STR vIPXRouterDescription	1.3.6.1.4.1.800.2.2.3.1.1.5	DisplayString	read-write	Textual description of the router instance.
vIPXRouterEntry	1.3.6.1.4.1.800.2.2.3.1.1		not-accessible	A VLAN entry.
INT vIPXRouterFramingType	1.3.6.1.4.1.800.2.2.3.1.1.4	INTEGER	read-write	Provides the ability to set the outbound frame type for IPX traffic. The default frame type is 802.2 Novell Raw. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
vIPXRouterInfo	1.3.6.1.4.1.800.2.2.3
OCT vIPXRouterNetAddress	1.3.6.1.4.1.800.2.2.3.1.1.3	OCTET STRING	read-write	The IPX network address for this virtual bridge.
XYL vIPXRouterOperStatus	1.3.6.1.4.1.800.2.2.3.1.1.7	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router environment.
INT vIPXRouterProtocol	1.3.6.1.4.1.800.2.2.3.1.1.2	INTEGER	read-write	The routing protocol(s) for this virtual router port. Each IPX router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipxNone(1), ipxRipOnly(2), ipxRipAndSap(3), ipxTriggered(4)
vIPXRouterTable	1.3.6.1.4.1.800.2.2.3.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
INT vIPXRouterVLan	1.3.6.1.4.1.800.2.2.3.1.1.1	INTEGER	read-write	VLAN ID for this vIPXRouterEntry instance.
INT vIPXSrcRteType	1.3.6.1.4.1.800.2.2.3.1.1.8	INTEGER	read-write	Provide the ability to set the type of source routing broadcasts between AllRoutesExplorer(0) and SpanningTreeExplorer(1).
XYL vLanAdmStatus	1.3.6.1.4.1.800.2.2.1.2.1.5	XylanVlanAdminStatCodes	read-write	The administrative status which can be set by configuration. Disable(1) will disable ALL vports that are connected to this VLAN, enable(2) will enable ALL ports on this VLAN, delete(3) will dettach and delete the ports/routers AND remove the VLAN.
INT vLanAuthGroup	1.3.6.1.4.1.800.2.2.1.2.1.11	INTEGER	read-write	If set to enable, makes this a authenticated group. If set to disable, makes this a non-authenticated group. For it to be set to enable, the group should be a mobile group.
OCT vLanAuthGroupProtocol	1.3.6.1.4.1.800.2.2.1.2.1.12	OCTET STRING	read-write	If a NULL string is returned as the value, this object is not applicable to that group. The contents of the string can interpreted based on the first byte. if the first byte is 1, the protocol is IP ( for all encaps ). 2, the protocol is IPX 3, the protocol is DECNET 4, the protocol is APPLETALK 5, the protocol is specified as an Ether-Type value with the next two bytes indicating the ether-type value, for e.g banyan vines ether-type will be specified as 08 0B AD 6, the protocol is specified using dsap and ssap values with the next two bytes giving the dsap and ssap value respectively, for e.g for banyan vines llc encap, it would look like 09 BC BC. 7, the protocol is specified using snap header with the next 5 bytes indicating the snap header for that protocol. For e.g if banyan vines snap has to be specified, it would look like, 0A 00 00 00 80 C4. FF, for all protocols.
INT vLanBrdgTpExtendedAgeingTime	1.3.6.1.4.1.800.2.2.1.2.1.14	INTEGER	read-write	The AutoTracker extended ageing timer. This value indicates how long the switch will remember the mac address and its associated vlan information. The default value is 1200 secs. This means that the mac information will be remembered for (vLanBrdgTpExtendedAgeingTime - vBrdgTpAgingTime) seconds after the mac is aged out. This value must be set to a value greater than or equal to vBrdgTpAgingTime.
MAC vLanBridgeAddress	1.3.6.1.4.1.800.2.2.1.2.1.2	MacAddress	read-only	The MAC address used by the instance of VLAN which specified in vLanCurrentNumber when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this VLAN. However it is only required to be unique. When concatenated with vStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
INT vLanBridgeType	1.3.6.1.4.1.800.2.2.1.2.1.3	INTEGER	read-only	Indicates what type of bridging this VLAN can perform. If a VLAN is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
INT vLanCurrentNumber	1.3.6.1.4.1.800.2.2.1.1	INTEGER	read-write	The current instance of Virtual LAN which corresponds to vLanNumber in object type vLanEntry. All the Bridging, Spanning Tree, and interface parameters refered thereafter will be referenced from this instance only. Default value upon the OmniSwitch power up is 1. It must be set to the desired value before any access to the rest of the virtual LAN system.
STR vLanDescription	1.3.6.1.4.1.800.2.2.1.2.1.4	DisplayString	read-write	Textual description of the VLAN instance.
vLanEntry	1.3.6.1.4.1.800.2.2.1.2.1		not-accessible	A VLAN entry.
INT vLanFloodOverride	1.3.6.1.4.1.800.2.2.1.2.1.8	INTEGER	read-write	Provides the flood limit value for all virtual ports that belong to the specied VLAN. The number is given in bytes per second. -1 and 0 have a special meaning. -1 means use the default or configured flood limit for each virtual port that belongs to the specified VLAN. 0 disables flood limiting on all virtual ports that belong to the specifed VLAN.
vLanInfo	1.3.6.1.4.1.800.2.2.1
INT vLanMobileGroup	1.3.6.1.4.1.800.2.2.1.2.1.10	INTEGER	read-write	If set to enabled, makes this a mobile group. If set to disabled, makes this a non-mobile gropu.
XYL vLanMode	1.3.6.1.4.1.800.2.2.1.2.1.7	XylanVlanModes	read-write	Provides special operating mode setup and status. Currently this object is used to specify weather the VLAN supports the standard or ATM CIP connections.
INT vLanNextFreeNumber	1.3.6.1.4.1.800.2.2.1.3	INTEGER	read-only	This is the next unused VLAN number. Typically this will be used to create a new VLAN with the next highest number.
INT vLanNumber	1.3.6.1.4.1.800.2.2.1.2.1.1	INTEGER	read-write	The VLAN number identifying this instance. Valid range from 1 to 65535.
XYL vLanOperStatus	1.3.6.1.4.1.800.2.2.1.2.1.6	XylanVlanOperStatCodes	read-only	Provide operating status of a particular VLAN environment.
INT vLanPriority	1.3.6.1.4.1.800.2.2.1.2.1.15	INTEGER	read-write	This is the priority of the given VLAN. It can be any one level from 0 to 7 with 0 being the lowest and 7 being the highest
MAC vLanRouterAddress	1.3.6.1.4.1.800.2.2.1.2.1.9	MacAddress	read-write	The user-configured MAC address used by the the VLAN's router port (IP / IPX). If this value has not been configured, the value returned is zero and this VLAN's router port will use a factory provided default value. The address should be specified in canonical order.
INT vLanStpStatus	1.3.6.1.4.1.800.2.2.1.2.1.13	INTEGER	read-write	Indicates status of spanning tree for the current VLAN.
vLanTable	1.3.6.1.4.1.800.2.2.1.2		not-accessible	A list of Virtual LAN instances in this physical OmniSwitch.
vPmap	1.3.6.1.4.1.800.2.2.17
vPmapConfigEntry	1.3.6.1.4.1.800.2.2.17.3.1		not-accessible	A Port Mapping configuration table entry.
vPmapConfigTable	1.3.6.1.4.1.800.2.2.17.3		not-accessible	A list of Port Mapping config table instance on this physical OmniSwitch or OSR.
vPmapEgressEntry	1.3.6.1.4.1.800.2.2.17.2.1		not-accessible	A Port Mapping Egress Port entry.
vPmapEgressTable	1.3.6.1.4.1.800.2.2.17.2		not-accessible	A list of Port Mapping Egress port table instance on this physical OmniSwitch or OSR.
vPmapIngressEntry	1.3.6.1.4.1.800.2.2.17.1.1		not-accessible	A Port Mapping Ingress Port entry.
vPmapIngressTable	1.3.6.1.4.1.800.2.2.17.1		not-accessible	A list of Port Mapping Ingress port table instance on this physical OmniSwitch or OSR.
INT vPmapNextId	1.3.6.1.4.1.800.2.2.17.4	INTEGER	read-only	The unique number that identifiers the next Port Mapping Table.
CTR vRipBadAddr	1.3.6.1.4.1.800.2.2.7.1.1.9	Counter	read-only	The number of RIP packets received on this virtual LAN whose host portion of the source IP address is bad.
CTR vRipBadCommand	1.3.6.1.4.1.800.2.2.7.1.1.10	Counter	read-only	The number of RIP packets received on this virtual LAN whose command type was neither a request nor a response.
CTR vRipBadFamily	1.3.6.1.4.1.800.2.2.7.1.1.7	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a bad value for the family type.
CTR vRipBadMetric	1.3.6.1.4.1.800.2.2.7.1.1.8	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a bad value for a route's metric.
CTR vRipBadSize	1.3.6.1.4.1.800.2.2.7.1.1.4	Counter	read-only	The number of RIP packets received on this virtual LAN whose size was incorrect.
CTR vRipBadVersion	1.3.6.1.4.1.800.2.2.7.1.1.5	Counter	read-only	The number of RIP packets received on this virtual LAN whose version number was incorrect.
vRipInfo	1.3.6.1.4.1.800.2.2.7
vRipInfoEntry	1.3.6.1.4.1.800.2.2.7.1.1		not-accessible	A VLAN entry for RIP statistics.
vRipInfoTable	1.3.6.1.4.1.800.2.2.7.1		not-accessible	A list of Virtual LAN instances for RIP statistics.
INT vRipInfovLanNumber	1.3.6.1.4.1.800.2.2.7.1.1.1	INTEGER	read-only	The VLAN number identifying this instance. Valid range from 1 to 65535.
CTR vRipInPkts	1.3.6.1.4.1.800.2.2.7.1.1.2	Counter	read-only	The number of RIP routing updates and requests received on this virtual LAN.
CTR vRipNonZero	1.3.6.1.4.1.800.2.2.7.1.1.6	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a non-zero value in one of the 'must be zero' fields.
CTR vRipOutPkts	1.3.6.1.4.1.800.2.2.7.1.1.3	Counter	read-only	The number of RIP routing updates and requests sent on this virtual LAN.
CTR vRipTransmitsFailed	1.3.6.1.4.1.800.2.2.7.1.1.13	Counter	read-only	The number of RIP routing updaates or requests that the OmniSwitch was unable to transmit.
vSr	1.3.6.1.4.1.800.2.2.8
CTR vSrApeInFrames	1.3.6.1.4.1.800.2.2.8.1.1.13	Counter	read-only	The number of All Paths Explorer frames, also referred to as All Routes Explorer frames, that have been received by this virtual port from its segment.
CTR vSrApeOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.14	Counter	read-only	The number of all Paths Explorer Frames, also referred to as All Routes Explorer frames, that have been transmitted by this virtual port on its segment.
INT vSrAREblock	1.3.6.1.4.1.800.2.2.8.1.1.24	INTEGER	read-write	Indicates whether this port would treat ARE frames exactly like STE frames which would be blocked if the Spanning Tree mode is blocking. 1 - this port would not block ARE. 2 - this port would block ARE.
INT vSrBridgeLfMode	1.3.6.1.4.1.800.2.2.8.1.1.22	INTEGER	read-only	Indicates whether the bridge operates using older 3 bit length negotiation fields or the newer 6 bit length field in its RIF.
INT vSrBridgeNum	1.3.6.1.4.1.800.2.2.8.1.1.7	INTEGER	read-write	A bridge number uniquely identifies a bridge when more than one bridge is used to span the same two segments. Current source routing protocols limit this value to the range: 0 through 15. A value of 65535 signifies that no bridge number is assigned to this bridge.
CTR vSrDupLanIdOrTreeErrors	1.3.6.1.4.1.800.2.2.8.1.1.20	Counter	read-only	The number of duplicate LAN IDs or Tree errors. This helps in detection of problems in networks containing older IBM Source Routing Bridges.
CTR vSrDuplicateSegmentDiscards	1.3.6.1.4.1.800.2.2.8.1.1.18	Counter	read-only	The number of frames that have been discarded by this virtual port because the routing descriptor field contained a duplicate segment identifier.
INT vSrFuncType	1.3.6.1.4.1.800.2.2.8.1.1.3	INTEGER	read-only	The service type of the port for which this entry contains Source Route management information.
INT vSrHopCount	1.3.6.1.4.1.800.2.2.8.1.1.5	INTEGER	read-write	The maximum number of routing descriptors allowed in an All Paths or Spanning Tree Explorer frames.
CTR vSrHopCountExceededDiscards	1.3.6.1.4.1.800.2.2.8.1.1.19	Counter	read-only	The number of explorer frames that have been discarded by this virtual port because the Routing Information Field has exceeded the maximum route descriptor length.
INT vSrHopCountIn	1.3.6.1.4.1.800.2.2.8.1.1.25	INTEGER	read-write	The maximum number of routing descriptors allowed in an inbound All Paths or Spanning Tree Explorer frames.
INT vSrInstance	1.3.6.1.4.1.800.2.2.8.1.1.4	INTEGER	read-only	The service type instance of the port for which this entry contains Source Route management information.
INT vSrInterface	1.3.6.1.4.1.800.2.2.8.1.1.2	INTEGER	read-only	The on-board interface number of the port for which this entry contains Source Route management information.
CTR vSrInvalidRif	1.3.6.1.4.1.800.2.2.8.1.1.17	Counter	read-only	The number of explorer frames that have been discarded by this virtual port because the routing Information field contained an invalid value.
CTR vSrLanIdMismatches	1.3.6.1.4.1.800.2.2.8.1.1.21	Counter	read-only	The number of ARE and STE frames that were discarded because the last LAN ID in the routing information field did not equal the LAN-in ID. This error can occur in implementations which do only a LAN-in ID and Bridge Number check instead of a LAN-in ID, Bridge Number, and LAN-out ID check before they forward broadcast frames.
INT vSrLargestFrame	1.3.6.1.4.1.800.2.2.8.1.1.9	INTEGER	read-write	The maximum size of the INFO field (LLC and above) that this virtual port can send/receive. It does not include any MAC level (framing) octets. The value of this object is used by this bridge to determine whether a modification of the LargestFrame (LF, see [14]) field of the Routing Control field of the Routing Information Field is necessary. 64 valid values are defined by the IEEE 802.5M SRT Addendum: 516, 635, 754, 873, 993, 1112, 1231, 1350, 1470, 1542, 1615, 1688, 1761, 1833, 1906, 1979, 2052, 2345, 2638, 2932, 3225, 3518, 3812, 4105, 4399, 4865, 5331, 5798, 6264, 6730, 7197, 7663, 8130, 8539, 8949, 9358, 9768, 10178, 10587, 10997, 11407, 12199, 12992, 13785, 14578, 15370, 16163, 16956, 17749, 20730, 23711, 26693, 29674, 32655, 35637, 38618, 41600, 44591, 47583, 50575, 53567, 56559, 59551, and 65535. An illegal value will not be accepted by the bridge.
INT vSrLocalSegment	1.3.6.1.4.1.800.2.2.8.1.1.6	INTEGER	read-write	The segment number that uniquely identifies the segment to which this virtual port is connected. Current source routing protocols limit this value to the range: 0 through 4095. (The value 0 is used by some management applications for special test cases.) A value of 65535 signifies that no segment number is assigned to this virtual port.
vSrPortEntry	1.3.6.1.4.1.800.2.2.8.1.1		not-accessible	A list of information for each virtual port of a source route switch.
INT vSrPortType	1.3.6.1.4.1.800.2.2.8.1.1.23	INTEGER	read-write	Indicates whether this port is a SRT or SR only SRT = 1 SR = 2
INT vSrSapDenyFilter1	1.3.6.1.4.1.800.2.2.8.1.1.26	INTEGER	read-write	Packets with this SAP value are to be discarded.
INT vSrSapDenyFilter2	1.3.6.1.4.1.800.2.2.8.1.1.27	INTEGER	read-write	Packets with this SAP value are to be discarded.
INT vSrSapFilterEnable	1.3.6.1.4.1.800.2.2.8.2	INTEGER	read-write	A scalar value to enable or disable the SAP filtering feature in this source route switch.
INT vSrSapPermitFilter1	1.3.6.1.4.1.800.2.2.8.1.1.28	INTEGER	read-write	Packets without this SAP value are to be discarded.
INT vSrSapPermitFilter2	1.3.6.1.4.1.800.2.2.8.1.1.29	INTEGER	read-write	Packets without this SAP value are to be discarded.
INT vSrSlot	1.3.6.1.4.1.800.2.2.8.1.1.1	INTEGER	read-only	The physical slot number of the port for which this entry contains Source Route management information.
CTR vSrSpecInFrames	1.3.6.1.4.1.800.2.2.8.1.1.11	Counter	read-only	The number of Specifically Routed frames, also referred to as Source Routed Frames, that have been received from this virtual port's segment.
CTR vSrSpecOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.12	Counter	read-only	The number of Specifically Routed frames, also referred to as Source Routed Frames, that this virtual port has transmitted on its segment.
CTR vSrSteInFrames	1.3.6.1.4.1.800.2.2.8.1.1.15	Counter	read-only	The number of spanning tree explorer frames that have been received by this virtual port from its segment.
CTR vSrSteOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.16	Counter	read-only	The number of spanning tree explorer frames that have been transmitted by this virtual port on its segment.
INT vSrSTESpanMode	1.3.6.1.4.1.800.2.2.8.1.1.10	INTEGER	read-write	Determines how this virtual port behaves when presented with a Spanning Tree Explorer frame. The value 'disabled(2)' indicates that the virtual port will not accept or send Spanning Tree Explorer packets; any STE packets received will be silently discarded. The value 'forced(3)' indicates the virtual port will always accept and propagate Spanning Tree Explorer frames. This allows a manually configured Spanning Tree for this class of packet to be configured. Note that unlike transparent bridging, this is not catastrophic to the network if there are loops. The value 'auto-span(1)' can only be returned by a bridge that both implements the Spanning Tree Protocol and has use of the protocol enabled on this virtual port. The behavior of the virtual port for Spanning Tree Explorer frames is determined by the state of vStpPortState. If the virtual port is in the 'forwarding' state, the frame will be accepted or propagated. Otherwise, it will be silently discarded.
vSrTable	1.3.6.1.4.1.800.2.2.8.1		not-accessible	A table that contains information about every virtual port that is associated with this source route switch.
INT vSrVirtualRing	1.3.6.1.4.1.800.2.2.8.1.1.8	INTEGER	read-write	This is to indicate whether the ring that this virtual port is connected to is virtual or physical 1 = virtual 2 = physical.
BRI vStpBridgeAddress	1.3.6.1.4.1.800.2.2.5.3	BridgeId	read-only	The bridge identifier of this VLAN of the spanning tree as determined by the Spanning Tree Protocol as executed by this VLAN.
TIM vStpBridgeForwardDelay	1.3.6.1.4.1.800.2.2.5.18	Timeout	read-write	The value that all VLANs use for ForwardDelay when this VLAN is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of vStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM vStpBridgeHelloTime	1.3.6.1.4.1.800.2.2.5.17	Timeout	read-write	The value that all VLANs use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM vStpBridgeMaxAge	1.3.6.1.4.1.800.2.2.5.16	Timeout	read-write	The value that all bridges use for MaxAge when this VLAN is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of vStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
BRI vStpDesignatedRoot	1.3.6.1.4.1.800.2.2.5.6	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this VLAN. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
INT vStpForwardDelay	1.3.6.1.4.1.800.2.2.5.15	INTEGER	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to vStpBridgeForwardDelay which is the value that this VLAN and all others would start using if/when this bridge were to become the root.]
TIM vStpHelloTime	1.3.6.1.4.1.800.2.2.5.13	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this VLAN on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this VLAN is currently using.
INT vStpHoldTime	1.3.6.1.4.1.800.2.2.5.14	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this VLAN, in units of hundredths of a second.
vStpInfo	1.3.6.1.4.1.800.2.2.5
INT vStpLanMode	1.3.6.1.4.1.800.2.2.5.20	INTEGER	read-write	Indicates which type of spanning tree (IEEE or IBM) is to be used for the current VLAN.
TIM vStpMaxAge	1.3.6.1.4.1.800.2.2.5.12	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
BRI vStpPortDesignatedBridge	1.3.6.1.4.1.800.2.2.5.19.1.11	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
INT vStpPortDesignatedCost	1.3.6.1.4.1.800.2.2.5.19.1.10	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
XYL vStpPortDesignatedPtFuncTyp	1.3.6.1.4.1.800.2.2.5.19.1.15	XylanPortFuncCodes	read-only	The service type of the port on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtFuncTypInst	1.3.6.1.4.1.800.2.2.5.19.1.16	INTEGER	read-only	The service type instance of the port on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtIF	1.3.6.1.4.1.800.2.2.5.19.1.14	INTEGER	read-only	The on-board interface number of the port on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtPrio	1.3.6.1.4.1.800.2.2.5.19.1.12	INTEGER	read-only	The priority portion of the port ID on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtSlot	1.3.6.1.4.1.800.2.2.5.19.1.13	INTEGER	read-only	The slot of the port on the Designated Bridge for this port's segment.
BRI vStpPortDesignatedRoot	1.3.6.1.4.1.800.2.2.5.19.1.9	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT vStpPortEnable	1.3.6.1.4.1.800.2.2.5.19.1.7	INTEGER	read-write	The enabled/disabled status of the port.
vStpPortEntry	1.3.6.1.4.1.800.2.2.5.19.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
INT vStpPortForwardTransitions	1.3.6.1.4.1.800.2.2.5.19.1.17	INTEGER	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT vStpPortFuncTyp	1.3.6.1.4.1.800.2.2.5.19.1.3	INTEGER	read-only	The service type of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortFuncTypInst	1.3.6.1.4.1.800.2.2.5.19.1.4	INTEGER	read-only	The service type instance of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortIF	1.3.6.1.4.1.800.2.2.5.19.1.2	INTEGER	read-only	The on-board interface number of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortPathCost	1.3.6.1.4.1.800.2.2.5.19.1.8	INTEGER	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT vStpPortPriority	1.3.6.1.4.1.800.2.2.5.19.1.5	INTEGER	read-write	The priority of this port which used originally as part of the port ID specified in 802.1D.
INT vStpPortSlot	1.3.6.1.4.1.800.2.2.5.19.1.1	INTEGER	read-only	The slot number of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortState	1.3.6.1.4.1.800.2.2.5.19.1.6	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. For ports which are disabled (see vStpPortEnable), this object will have a value of disabled(1). Xylan does not support the broken(6) state as defined in RFC1493.
vStpPortTable	1.3.6.1.4.1.800.2.2.5.19		not-accessible	A table that contains port-specific information for the Spanning Tree Protocol.
INT vStpPriority	1.3.6.1.4.1.800.2.2.5.2	INTEGER	read-write	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of vLanBridgeAddress.
INT vStpProtocolSpecification	1.3.6.1.4.1.800.2.2.5.1	INTEGER	read-only	The version of the Spanning Tree Protocol implemented for the Xylan products. The IEE 802.1d implementation is the only version supported. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
INT vStpRootCost	1.3.6.1.4.1.800.2.2.5.7	INTEGER	read-only	The cost of the path to the root as seen from this VLAN bridge.
XYL vStpRootPortFuncTyp	1.3.6.1.4.1.800.2.2.5.10	XylanPortFuncCodes	read-only	The service type of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vStpRootPortFuncTypInst	1.3.6.1.4.1.800.2.2.5.11	INTEGER	read-only	The service type instance of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vStpRootPortIF	1.3.6.1.4.1.800.2.2.5.9	INTEGER	read-only	The on-board interface of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vStpRootPortSlot	1.3.6.1.4.1.800.2.2.5.8	INTEGER	read-only	The slot number of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
XYL vStpStatus	1.3.6.1.4.1.800.2.2.5.21	XylanVlanOperStatCodes	read-write	Indicates status of spanning tree for the current VLAN.
TIK vStpTimeSinceTopologyChange	1.3.6.1.4.1.800.2.2.5.4	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the VLAN bridge entity.
CTR vStpTopChanges	1.3.6.1.4.1.800.2.2.5.5	Counter	read-only	The total number of topology changes detected by this VLAN bridge since the management entity was last reset or initialized.
vTrunking	1.3.6.1.4.1.800.2.2.9
INT vTrunkingCommand	1.3.6.1.4.1.800.2.2.9.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given trunking service.
INT vTrunkingLanNumber	1.3.6.1.4.1.800.2.2.9.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given trunking service.
INT vTrunkingServicesBridgeID	1.3.6.1.4.1.800.2.2.9.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given trunking service. A value of 0 means that the Virtual Bridge port does not exist.
STR vTrunkingServicesDescription	1.3.6.1.4.1.800.2.2.9.1.1.3	DisplayString	read-write	A description of the trunking service being provided.
vTrunkingServicesEntry	1.3.6.1.4.1.800.2.2.9.1.1		not-accessible	A trunking services entry.
INT vTrunkingServicesSlot	1.3.6.1.4.1.800.2.2.9.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the trunking service.
INT vTrunkingServicesStation	1.3.6.1.4.1.800.2.2.9.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the trunking service.
vTrunkingServicesTable	1.3.6.1.4.1.800.2.2.9.1		not-accessible	A list of commands to add or remove Virtual LANs from a trunking service.
INT vTrunkingSlot	1.3.6.1.4.1.800.2.2.9.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the trunking service.
INT vTrunkingStation	1.3.6.1.4.1.800.2.2.9.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the trunking service.
vTrunkingVlanEntry	1.3.6.1.4.1.800.2.2.9.2.1		not-accessible	A trunking Virtual LAN entry.
vTrunkingVlanTable	1.3.6.1.4.1.800.2.2.9.2		not-accessible	A list of commands to add or remove Virtual LANs from a trunking service.

OID symbolic	OID numeric	Type	Access	Description
vLanInfo	1.3.6.1.4.1.800.2.2.1
INT vLanCurrentNumber	1.3.6.1.4.1.800.2.2.1.1	INTEGER	read-write	The current instance of Virtual LAN which corresponds to vLanNumber in object type vLanEntry. All the Bridging, Spanning Tree, and interface parameters refered thereafter will be referenced from this instance only. Default value upon the OmniSwitch power up is 1. It must be set to the desired value before any access to the rest of the virtual LAN system.
vLanTable	1.3.6.1.4.1.800.2.2.1.2		not-accessible	A list of Virtual LAN instances in this physical OmniSwitch.
vLanEntry	1.3.6.1.4.1.800.2.2.1.2.1		not-accessible	A VLAN entry.
INT vLanNumber	1.3.6.1.4.1.800.2.2.1.2.1.1	INTEGER	read-write	The VLAN number identifying this instance. Valid range from 1 to 65535.
MAC vLanBridgeAddress	1.3.6.1.4.1.800.2.2.1.2.1.2	MacAddress	read-only	The MAC address used by the instance of VLAN which specified in vLanCurrentNumber when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this VLAN. However it is only required to be unique. When concatenated with vStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
INT vLanBridgeType	1.3.6.1.4.1.800.2.2.1.2.1.3	INTEGER	read-only	Indicates what type of bridging this VLAN can perform. If a VLAN is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
STR vLanDescription	1.3.6.1.4.1.800.2.2.1.2.1.4	DisplayString	read-write	Textual description of the VLAN instance.
XYL vLanAdmStatus	1.3.6.1.4.1.800.2.2.1.2.1.5	XylanVlanAdminStatCodes	read-write	The administrative status which can be set by configuration. Disable(1) will disable ALL vports that are connected to this VLAN, enable(2) will enable ALL ports on this VLAN, delete(3) will dettach and delete the ports/routers AND remove the VLAN.
XYL vLanOperStatus	1.3.6.1.4.1.800.2.2.1.2.1.6	XylanVlanOperStatCodes	read-only	Provide operating status of a particular VLAN environment.
XYL vLanMode	1.3.6.1.4.1.800.2.2.1.2.1.7	XylanVlanModes	read-write	Provides special operating mode setup and status. Currently this object is used to specify weather the VLAN supports the standard or ATM CIP connections.
INT vLanFloodOverride	1.3.6.1.4.1.800.2.2.1.2.1.8	INTEGER	read-write	Provides the flood limit value for all virtual ports that belong to the specied VLAN. The number is given in bytes per second. -1 and 0 have a special meaning. -1 means use the default or configured flood limit for each virtual port that belongs to the specified VLAN. 0 disables flood limiting on all virtual ports that belong to the specifed VLAN.
MAC vLanRouterAddress	1.3.6.1.4.1.800.2.2.1.2.1.9	MacAddress	read-write	The user-configured MAC address used by the the VLAN's router port (IP / IPX). If this value has not been configured, the value returned is zero and this VLAN's router port will use a factory provided default value. The address should be specified in canonical order.
INT vLanMobileGroup	1.3.6.1.4.1.800.2.2.1.2.1.10	INTEGER	read-write	If set to enabled, makes this a mobile group. If set to disabled, makes this a non-mobile gropu.
INT vLanAuthGroup	1.3.6.1.4.1.800.2.2.1.2.1.11	INTEGER	read-write	If set to enable, makes this a authenticated group. If set to disable, makes this a non-authenticated group. For it to be set to enable, the group should be a mobile group.
OCT vLanAuthGroupProtocol	1.3.6.1.4.1.800.2.2.1.2.1.12	OCTET STRING	read-write	If a NULL string is returned as the value, this object is not applicable to that group. The contents of the string can interpreted based on the first byte. if the first byte is 1, the protocol is IP ( for all encaps ). 2, the protocol is IPX 3, the protocol is DECNET 4, the protocol is APPLETALK 5, the protocol is specified as an Ether-Type value with the next two bytes indicating the ether-type value, for e.g banyan vines ether-type will be specified as 08 0B AD 6, the protocol is specified using dsap and ssap values with the next two bytes giving the dsap and ssap value respectively, for e.g for banyan vines llc encap, it would look like 09 BC BC. 7, the protocol is specified using snap header with the next 5 bytes indicating the snap header for that protocol. For e.g if banyan vines snap has to be specified, it would look like, 0A 00 00 00 80 C4. FF, for all protocols.
INT vLanStpStatus	1.3.6.1.4.1.800.2.2.1.2.1.13	INTEGER	read-write	Indicates status of spanning tree for the current VLAN.
INT vLanBrdgTpExtendedAgeingTime	1.3.6.1.4.1.800.2.2.1.2.1.14	INTEGER	read-write	The AutoTracker extended ageing timer. This value indicates how long the switch will remember the mac address and its associated vlan information. The default value is 1200 secs. This means that the mac information will be remembered for (vLanBrdgTpExtendedAgeingTime - vBrdgTpAgingTime) seconds after the mac is aged out. This value must be set to a value greater than or equal to vBrdgTpAgingTime.
INT vLanPriority	1.3.6.1.4.1.800.2.2.1.2.1.15	INTEGER	read-write	This is the priority of the given VLAN. It can be any one level from 0 to 7 with 0 being the lowest and 7 being the highest
INT vLanNextFreeNumber	1.3.6.1.4.1.800.2.2.1.3	INTEGER	read-only	This is the next unused VLAN number. Typically this will be used to create a new VLAN with the next highest number.
vIPRouterInfo	1.3.6.1.4.1.800.2.2.2
vIPRouterTable	1.3.6.1.4.1.800.2.2.2.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
vIPRouterEntry	1.3.6.1.4.1.800.2.2.2.1.1		not-accessible	A VLAN entry.
INT vIPRouterVLan	1.3.6.1.4.1.800.2.2.2.1.1.1	INTEGER	read-write	VLAN ID for this vIPRouterEntry instance.
OCT vIPRouterProtocol	1.3.6.1.4.1.800.2.2.2.1.1.2	OCTET STRING	read-write	The routing protocol(s) for this virtual router port. Each IP router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipOther(1), ipRip(2), ipEgp(4), ipGgp(8), ipHello(16), ipIs-is(32), ipEs-is(64), ipCiscoIgrp(128), ipBbnSpfIgp(256), ipOigp(512)
IP vIPRouterNetAddress	1.3.6.1.4.1.800.2.2.2.1.1.3	IpAddress	read-write	The IP network address for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP vIPRouterSubNetMask	1.3.6.1.4.1.800.2.2.2.1.1.4	IpAddress	read-write	The IP network subnet mask for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP vIPRouterBcastAddress	1.3.6.1.4.1.800.2.2.2.1.1.5	IpAddress	read-write	The IP broadcast address for this virtual bridge instance for the purpose of allowing access from the external network management system.
STR vIPRouterDescription	1.3.6.1.4.1.800.2.2.2.1.1.6	DisplayString	read-write	Textual description of the router instance.
XYL vIPRouterAdmStatus	1.3.6.1.4.1.800.2.2.2.1.1.7	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enable(2) or disable(1) (or delete (3)) upon user's request.
XYL vIPRouterOperStatus	1.3.6.1.4.1.800.2.2.2.1.1.8	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
INT vIPRouterFramingType	1.3.6.1.4.1.800.2.2.2.1.1.9	INTEGER	read-write	Provides the ability to set the outbound frame type for IP traffic. The default frame type is Ethernet 2. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
INT vIPRouterRipConfigMode	1.3.6.1.4.1.800.2.2.2.1.1.10	INTEGER	read-write	RIP's operational mode. 'silent' means that RIP listens for routing updates but does not send them. 'deaf' means that RIP sends routing updates but not listen to them. 'active' means that RIP both sends and receives routing updates, and 'inactive' means that RIP is not operational on the given virtual LAN. The default is 'simple'.
vIPRouterRelayTable	1.3.6.1.4.1.800.2.2.2.2		not-accessible	A list of UDP Relay Service instances.
vIPRouterRelayEntry	1.3.6.1.4.1.800.2.2.2.2.1		not-accessible	A UDP Relay Service entry.
VIP vIPRouterRelayService	1.3.6.1.4.1.800.2.2.2.2.1.1	VIPRouterRelayServType	read-only	This specifies the UDP Relay Service to be forwarded.
INT vIPRouterRelayMode	1.3.6.1.4.1.800.2.2.2.2.1.2	INTEGER	read-write	This controls whether the internal UDP Relay service is enabled or disabled. When enabled, the service will forward packets to a specified server (or specified broadcast address.) or VLAN. Note that for BOOTP/DHCP service, unless the relay's next hop ip address (vIPRouterRelayForwAddr) is set to a valid value, it will not possible to enable the relay. For other services, a VLAN to forwared to (vIPRouterRelayForwVlan in vIPRouterRelayForwTable) or a next hop ip address must be set. The mode definitions are as follows: 1 - enabled 2 - configureRequest 3 - underConfiguration 4 - disabled A manager will set the state to configureRequest(2) before attempting to configure any other parameters for a particular UPD Service. The agent will then set the state to underConfiguration(3). When in the underConfiguration(3) state, a UDP service is not completely configured and will remain in this state until the management station is finished configuring and sets the state to either enabled(1) or disabled(4). A manager is restricted to changing the state of an entry in the following ways: config under To: valid Request config invalid From: valid OK NO OK OK configRequest N/A N/A N/A N/A underConfig OK NO OK OK invalid NO OK NO OK
IP vIPRouterRelayNextHop	1.3.6.1.4.1.800.2.2.2.2.1.3	IpAddress	read-write	This sets the relay's forwarding address. It can either be set to a distinct IP address (e.g. the address of a server), to an IP broadcast address or a VLAN.
INT vIPRouterRelayParam1	1.3.6.1.4.1.800.2.2.2.2.1.4	INTEGER	read-write	This sets the BOOTP/DHCP relay's maximum hops forwarding limit. If a BOOT/DHCP frame arrives with hopcount greater than or equal to vIPRouterRelayParam1, it will be dropped. For BOOTP/DHCP the legal range is 1..16. For Generic services, this sets the port number to be forwarded. The legal range is -1..65535 with -1 indicating the unset state.
INT vIPRouterRelayParam2	1.3.6.1.4.1.800.2.2.2.2.1.5	INTEGER	read-write	This sets the BOOTP/DHCP relay's forwarding delay and is only used by the BOOTP/DHCP service. For other services it is ignored. It is typically set as seconds, but the value is totally client dependent. The relay will not forward frames until client frames have 'secs' field set to at least the value of vIPRouterRelayParam2.
STR vIPRouterRelayDescription	1.3.6.1.4.1.800.2.2.2.2.1.6	DisplayString	read-write	This sets the service description for generic services. For other services, the description is fixed and may only be read.
vIPXRouterInfo	1.3.6.1.4.1.800.2.2.3
vIPXRouterTable	1.3.6.1.4.1.800.2.2.3.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
vIPXRouterEntry	1.3.6.1.4.1.800.2.2.3.1.1		not-accessible	A VLAN entry.
INT vIPXRouterVLan	1.3.6.1.4.1.800.2.2.3.1.1.1	INTEGER	read-write	VLAN ID for this vIPXRouterEntry instance.
INT vIPXRouterProtocol	1.3.6.1.4.1.800.2.2.3.1.1.2	INTEGER	read-write	The routing protocol(s) for this virtual router port. Each IPX router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipxNone(1), ipxRipOnly(2), ipxRipAndSap(3), ipxTriggered(4)
OCT vIPXRouterNetAddress	1.3.6.1.4.1.800.2.2.3.1.1.3	OCTET STRING	read-write	The IPX network address for this virtual bridge.
INT vIPXRouterFramingType	1.3.6.1.4.1.800.2.2.3.1.1.4	INTEGER	read-write	Provides the ability to set the outbound frame type for IPX traffic. The default frame type is 802.2 Novell Raw. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
STR vIPXRouterDescription	1.3.6.1.4.1.800.2.2.3.1.1.5	DisplayString	read-write	Textual description of the router instance.
XYL vIPXRouterAdmStatus	1.3.6.1.4.1.800.2.2.3.1.1.6	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enabled(2) or disabled(1) upon user's request.
XYL vIPXRouterOperStatus	1.3.6.1.4.1.800.2.2.3.1.1.7	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router environment.
INT vIPXSrcRteType	1.3.6.1.4.1.800.2.2.3.1.1.8	INTEGER	read-write	Provide the ability to set the type of source routing broadcasts between AllRoutesExplorer(0) and SpanningTreeExplorer(1).
vBrdgInfo	1.3.6.1.4.1.800.2.2.4
CTR vBrdgTpLearnEntryDiscards	1.3.6.1.4.1.800.2.2.4.1	Counter	read-only	The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
INT vBrdgTpAgingTime	1.3.6.1.4.1.800.2.2.4.2	INTEGER	read-write	The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
vBrdgTpFdbTable	1.3.6.1.4.1.800.2.2.4.3		not-accessible	A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function within its VLAN in determining how to propagate a received frame.
vBrdgTpFdbEntry	1.3.6.1.4.1.800.2.2.4.3.1		not-accessible	Information about a specific unicast MAC address for which the VLAN bridge has some forwarding and/or filtering information.
INT vBrdgTpFdbGroupId	1.3.6.1.4.1.800.2.2.4.3.1.1	INTEGER	read-only	The GroupId for this bridge.
MAC vBrdgTpFdbAddress	1.3.6.1.4.1.800.2.2.4.3.1.2	MacAddress	read-only	A unicast MAC address for which the VLAN bridge has forwarding and/or filtering information.
INT vBrdgTpFdbRcvPortSlot	1.3.6.1.4.1.800.2.2.4.3.1.3	INTEGER	read-only	The slot number of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvPortIF	1.3.6.1.4.1.800.2.2.4.3.1.4	INTEGER	read-only	The on-board interface number of the port that vBrdgTpFdbAddress is received.
XYL vBrdgTpFdbRcvPortFuncTyp	1.3.6.1.4.1.800.2.2.4.3.1.5	XylanPortFuncCodes	read-only	The service type of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvPortFuncTypInst	1.3.6.1.4.1.800.2.2.4.3.1.6	INTEGER	read-only	The service type instance of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvStatus	1.3.6.1.4.1.800.2.2.4.3.1.7	INTEGER	read-only	The status of this entry. Xylan does not support other(1) and self(4). The meanings of the values are: invalid(2) : this entry is no longer valid, but has not yet been flushed from the table. learned(3) : this entry has been learned. mgmt(5) : this entry is configured as a static entry.
INT vBrdgTpFdbRcvVLANMembership	1.3.6.1.4.1.800.2.2.4.3.1.8	INTEGER	read-only	The Auto-Tracker VLAN membership for this device. Each bit that is set in this objects 32 bit value indicates that the device is part of the VLAN given by that bits position.
INT vBrdgTpFdbDupStatus	1.3.6.1.4.1.800.2.2.4.3.1.9	INTEGER	read-only	The variable indicates if vBrdgTpFdbAddress is a duplicate Mac.
CTR vBrdgTpFdbLastSeenTime	1.3.6.1.4.1.800.2.2.4.3.1.10	Counter	read-only	The time since, the specific unicast MAC address for which the VLAN bridge has forwarding information was last seen.
vBrdgStaticTable	1.3.6.1.4.1.800.2.2.4.4		not-accessible	A table contains source addresses which can be configured to stay permanent (not aging out) in the Forwarding table.
vBrdgStaticEntry	1.3.6.1.4.1.800.2.2.4.4.1		not-accessible	Information about a specific unicast MAC address for which the VLAN bridge has VLAN information.
MAC vBrdgStaticAddress	1.3.6.1.4.1.800.2.2.4.4.1.1	MacAddress	read-write	The MAC address which the static status applies.
INT vBrdgStaticPortSlot	1.3.6.1.4.1.800.2.2.4.4.1.2	INTEGER	read-write	The slot number of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is provided, vBrdgStaticPortIF, vBrdgStaticPortFuncTyp and vBrdgStaticPortFuncTypInst must also be set.
INT vBrdgStaticPortIF	1.3.6.1.4.1.800.2.2.4.4.1.3	INTEGER	read-write	The on-board interface of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortFuncTyp and vBrdgStaticPortFuncTypInst must also be set.
XYL vBrdgStaticPortFuncTyp	1.3.6.1.4.1.800.2.2.4.4.1.4	XylanPortFuncCodes	read-write	The service type of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortIF and vBrdgStaticPortFuncTypInst must also be set.
INT vBrdgStaticPortFuncTypInst	1.3.6.1.4.1.800.2.2.4.4.1.5	INTEGER	read-write	The service type instance of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortIF and vBrdgStaticPortFuncTyp must also be set.
INT vBrdgStaticStatus	1.3.6.1.4.1.800.2.2.4.4.1.6	INTEGER	read-write	This object indicates the status of this entry. Xylan does not support other(1). The default value is permenent(3). invalid(2) - writing this value to the object removes the entry. permanent(3) - this entry will never age out and remain even after next reset. deleteOnReset(4) - this entry will not age out until reset. deleteOnTimeout(5) - write this value to the entry will cause it to age out.
INT vBrdgTpATVLANAgeingTime	1.3.6.1.4.1.800.2.2.4.5	INTEGER	read-write	The AutoTracker extended ageing timer. This value indicates how long the switch will remember the mac address and its associated vlan information. The default value is 1200 secs. This means that the mac information will be remembered for (vBrdgTpATVLANAgeingTime - vBrdgTpAgingTime) seconds after the mac is aged out. This value must be set to a value greater than or equal to vBrdgTpAgingTime.
vStpInfo	1.3.6.1.4.1.800.2.2.5
INT vStpProtocolSpecification	1.3.6.1.4.1.800.2.2.5.1	INTEGER	read-only	The version of the Spanning Tree Protocol implemented for the Xylan products. The IEE 802.1d implementation is the only version supported. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
INT vStpPriority	1.3.6.1.4.1.800.2.2.5.2	INTEGER	read-write	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of vLanBridgeAddress.
BRI vStpBridgeAddress	1.3.6.1.4.1.800.2.2.5.3	BridgeId	read-only	The bridge identifier of this VLAN of the spanning tree as determined by the Spanning Tree Protocol as executed by this VLAN.
TIK vStpTimeSinceTopologyChange	1.3.6.1.4.1.800.2.2.5.4	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the VLAN bridge entity.
CTR vStpTopChanges	1.3.6.1.4.1.800.2.2.5.5	Counter	read-only	The total number of topology changes detected by this VLAN bridge since the management entity was last reset or initialized.
BRI vStpDesignatedRoot	1.3.6.1.4.1.800.2.2.5.6	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this VLAN. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
INT vStpRootCost	1.3.6.1.4.1.800.2.2.5.7	INTEGER	read-only	The cost of the path to the root as seen from this VLAN bridge.
INT vStpRootPortSlot	1.3.6.1.4.1.800.2.2.5.8	INTEGER	read-only	The slot number of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vStpRootPortIF	1.3.6.1.4.1.800.2.2.5.9	INTEGER	read-only	The on-board interface of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
XYL vStpRootPortFuncTyp	1.3.6.1.4.1.800.2.2.5.10	XylanPortFuncCodes	read-only	The service type of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vStpRootPortFuncTypInst	1.3.6.1.4.1.800.2.2.5.11	INTEGER	read-only	The service type instance of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
TIM vStpMaxAge	1.3.6.1.4.1.800.2.2.5.12	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM vStpHelloTime	1.3.6.1.4.1.800.2.2.5.13	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this VLAN on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this VLAN is currently using.
INT vStpHoldTime	1.3.6.1.4.1.800.2.2.5.14	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this VLAN, in units of hundredths of a second.
INT vStpForwardDelay	1.3.6.1.4.1.800.2.2.5.15	INTEGER	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to vStpBridgeForwardDelay which is the value that this VLAN and all others would start using if/when this bridge were to become the root.]
TIM vStpBridgeMaxAge	1.3.6.1.4.1.800.2.2.5.16	Timeout	read-write	The value that all bridges use for MaxAge when this VLAN is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of vStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM vStpBridgeHelloTime	1.3.6.1.4.1.800.2.2.5.17	Timeout	read-write	The value that all VLANs use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM vStpBridgeForwardDelay	1.3.6.1.4.1.800.2.2.5.18	Timeout	read-write	The value that all VLANs use for ForwardDelay when this VLAN is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of vStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
vStpPortTable	1.3.6.1.4.1.800.2.2.5.19		not-accessible	A table that contains port-specific information for the Spanning Tree Protocol.
vStpPortEntry	1.3.6.1.4.1.800.2.2.5.19.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
INT vStpPortSlot	1.3.6.1.4.1.800.2.2.5.19.1.1	INTEGER	read-only	The slot number of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortIF	1.3.6.1.4.1.800.2.2.5.19.1.2	INTEGER	read-only	The on-board interface number of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortFuncTyp	1.3.6.1.4.1.800.2.2.5.19.1.3	INTEGER	read-only	The service type of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortFuncTypInst	1.3.6.1.4.1.800.2.2.5.19.1.4	INTEGER	read-only	The service type instance of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortPriority	1.3.6.1.4.1.800.2.2.5.19.1.5	INTEGER	read-write	The priority of this port which used originally as part of the port ID specified in 802.1D.
INT vStpPortState	1.3.6.1.4.1.800.2.2.5.19.1.6	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. For ports which are disabled (see vStpPortEnable), this object will have a value of disabled(1). Xylan does not support the broken(6) state as defined in RFC1493.
INT vStpPortEnable	1.3.6.1.4.1.800.2.2.5.19.1.7	INTEGER	read-write	The enabled/disabled status of the port.
INT vStpPortPathCost	1.3.6.1.4.1.800.2.2.5.19.1.8	INTEGER	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
BRI vStpPortDesignatedRoot	1.3.6.1.4.1.800.2.2.5.19.1.9	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT vStpPortDesignatedCost	1.3.6.1.4.1.800.2.2.5.19.1.10	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
BRI vStpPortDesignatedBridge	1.3.6.1.4.1.800.2.2.5.19.1.11	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtPrio	1.3.6.1.4.1.800.2.2.5.19.1.12	INTEGER	read-only	The priority portion of the port ID on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtSlot	1.3.6.1.4.1.800.2.2.5.19.1.13	INTEGER	read-only	The slot of the port on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtIF	1.3.6.1.4.1.800.2.2.5.19.1.14	INTEGER	read-only	The on-board interface number of the port on the Designated Bridge for this port's segment.
XYL vStpPortDesignatedPtFuncTyp	1.3.6.1.4.1.800.2.2.5.19.1.15	XylanPortFuncCodes	read-only	The service type of the port on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtFuncTypInst	1.3.6.1.4.1.800.2.2.5.19.1.16	INTEGER	read-only	The service type instance of the port on the Designated Bridge for this port's segment.
INT vStpPortForwardTransitions	1.3.6.1.4.1.800.2.2.5.19.1.17	INTEGER	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT vStpLanMode	1.3.6.1.4.1.800.2.2.5.20	INTEGER	read-write	Indicates which type of spanning tree (IEEE or IBM) is to be used for the current VLAN.
XYL vStpStatus	1.3.6.1.4.1.800.2.2.5.21	XylanVlanOperStatCodes	read-write	Indicates status of spanning tree for the current VLAN.
vRipInfo	1.3.6.1.4.1.800.2.2.7
vRipInfoTable	1.3.6.1.4.1.800.2.2.7.1		not-accessible	A list of Virtual LAN instances for RIP statistics.
vRipInfoEntry	1.3.6.1.4.1.800.2.2.7.1.1		not-accessible	A VLAN entry for RIP statistics.
INT vRipInfovLanNumber	1.3.6.1.4.1.800.2.2.7.1.1.1	INTEGER	read-only	The VLAN number identifying this instance. Valid range from 1 to 65535.
CTR vRipInPkts	1.3.6.1.4.1.800.2.2.7.1.1.2	Counter	read-only	The number of RIP routing updates and requests received on this virtual LAN.
CTR vRipOutPkts	1.3.6.1.4.1.800.2.2.7.1.1.3	Counter	read-only	The number of RIP routing updates and requests sent on this virtual LAN.
CTR vRipBadSize	1.3.6.1.4.1.800.2.2.7.1.1.4	Counter	read-only	The number of RIP packets received on this virtual LAN whose size was incorrect.
CTR vRipBadVersion	1.3.6.1.4.1.800.2.2.7.1.1.5	Counter	read-only	The number of RIP packets received on this virtual LAN whose version number was incorrect.
CTR vRipNonZero	1.3.6.1.4.1.800.2.2.7.1.1.6	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a non-zero value in one of the 'must be zero' fields.
CTR vRipBadFamily	1.3.6.1.4.1.800.2.2.7.1.1.7	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a bad value for the family type.
CTR vRipBadMetric	1.3.6.1.4.1.800.2.2.7.1.1.8	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a bad value for a route's metric.
CTR vRipBadAddr	1.3.6.1.4.1.800.2.2.7.1.1.9	Counter	read-only	The number of RIP packets received on this virtual LAN whose host portion of the source IP address is bad.
CTR vRipBadCommand	1.3.6.1.4.1.800.2.2.7.1.1.10	Counter	read-only	The number of RIP packets received on this virtual LAN whose command type was neither a request nor a response.
CTR vRipTransmitsFailed	1.3.6.1.4.1.800.2.2.7.1.1.13	Counter	read-only	The number of RIP routing updaates or requests that the OmniSwitch was unable to transmit.
vSr	1.3.6.1.4.1.800.2.2.8
vSrTable	1.3.6.1.4.1.800.2.2.8.1		not-accessible	A table that contains information about every virtual port that is associated with this source route switch.
vSrPortEntry	1.3.6.1.4.1.800.2.2.8.1.1		not-accessible	A list of information for each virtual port of a source route switch.
INT vSrSlot	1.3.6.1.4.1.800.2.2.8.1.1.1	INTEGER	read-only	The physical slot number of the port for which this entry contains Source Route management information.
INT vSrInterface	1.3.6.1.4.1.800.2.2.8.1.1.2	INTEGER	read-only	The on-board interface number of the port for which this entry contains Source Route management information.
INT vSrFuncType	1.3.6.1.4.1.800.2.2.8.1.1.3	INTEGER	read-only	The service type of the port for which this entry contains Source Route management information.
INT vSrInstance	1.3.6.1.4.1.800.2.2.8.1.1.4	INTEGER	read-only	The service type instance of the port for which this entry contains Source Route management information.
INT vSrHopCount	1.3.6.1.4.1.800.2.2.8.1.1.5	INTEGER	read-write	The maximum number of routing descriptors allowed in an All Paths or Spanning Tree Explorer frames.
INT vSrLocalSegment	1.3.6.1.4.1.800.2.2.8.1.1.6	INTEGER	read-write	The segment number that uniquely identifies the segment to which this virtual port is connected. Current source routing protocols limit this value to the range: 0 through 4095. (The value 0 is used by some management applications for special test cases.) A value of 65535 signifies that no segment number is assigned to this virtual port.
INT vSrBridgeNum	1.3.6.1.4.1.800.2.2.8.1.1.7	INTEGER	read-write	A bridge number uniquely identifies a bridge when more than one bridge is used to span the same two segments. Current source routing protocols limit this value to the range: 0 through 15. A value of 65535 signifies that no bridge number is assigned to this bridge.
INT vSrVirtualRing	1.3.6.1.4.1.800.2.2.8.1.1.8	INTEGER	read-write	This is to indicate whether the ring that this virtual port is connected to is virtual or physical 1 = virtual 2 = physical.
INT vSrLargestFrame	1.3.6.1.4.1.800.2.2.8.1.1.9	INTEGER	read-write	The maximum size of the INFO field (LLC and above) that this virtual port can send/receive. It does not include any MAC level (framing) octets. The value of this object is used by this bridge to determine whether a modification of the LargestFrame (LF, see [14]) field of the Routing Control field of the Routing Information Field is necessary. 64 valid values are defined by the IEEE 802.5M SRT Addendum: 516, 635, 754, 873, 993, 1112, 1231, 1350, 1470, 1542, 1615, 1688, 1761, 1833, 1906, 1979, 2052, 2345, 2638, 2932, 3225, 3518, 3812, 4105, 4399, 4865, 5331, 5798, 6264, 6730, 7197, 7663, 8130, 8539, 8949, 9358, 9768, 10178, 10587, 10997, 11407, 12199, 12992, 13785, 14578, 15370, 16163, 16956, 17749, 20730, 23711, 26693, 29674, 32655, 35637, 38618, 41600, 44591, 47583, 50575, 53567, 56559, 59551, and 65535. An illegal value will not be accepted by the bridge.
INT vSrSTESpanMode	1.3.6.1.4.1.800.2.2.8.1.1.10	INTEGER	read-write	Determines how this virtual port behaves when presented with a Spanning Tree Explorer frame. The value 'disabled(2)' indicates that the virtual port will not accept or send Spanning Tree Explorer packets; any STE packets received will be silently discarded. The value 'forced(3)' indicates the virtual port will always accept and propagate Spanning Tree Explorer frames. This allows a manually configured Spanning Tree for this class of packet to be configured. Note that unlike transparent bridging, this is not catastrophic to the network if there are loops. The value 'auto-span(1)' can only be returned by a bridge that both implements the Spanning Tree Protocol and has use of the protocol enabled on this virtual port. The behavior of the virtual port for Spanning Tree Explorer frames is determined by the state of vStpPortState. If the virtual port is in the 'forwarding' state, the frame will be accepted or propagated. Otherwise, it will be silently discarded.
CTR vSrSpecInFrames	1.3.6.1.4.1.800.2.2.8.1.1.11	Counter	read-only	The number of Specifically Routed frames, also referred to as Source Routed Frames, that have been received from this virtual port's segment.
CTR vSrSpecOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.12	Counter	read-only	The number of Specifically Routed frames, also referred to as Source Routed Frames, that this virtual port has transmitted on its segment.
CTR vSrApeInFrames	1.3.6.1.4.1.800.2.2.8.1.1.13	Counter	read-only	The number of All Paths Explorer frames, also referred to as All Routes Explorer frames, that have been received by this virtual port from its segment.
CTR vSrApeOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.14	Counter	read-only	The number of all Paths Explorer Frames, also referred to as All Routes Explorer frames, that have been transmitted by this virtual port on its segment.
CTR vSrSteInFrames	1.3.6.1.4.1.800.2.2.8.1.1.15	Counter	read-only	The number of spanning tree explorer frames that have been received by this virtual port from its segment.
CTR vSrSteOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.16	Counter	read-only	The number of spanning tree explorer frames that have been transmitted by this virtual port on its segment.
CTR vSrInvalidRif	1.3.6.1.4.1.800.2.2.8.1.1.17	Counter	read-only	The number of explorer frames that have been discarded by this virtual port because the routing Information field contained an invalid value.
CTR vSrDuplicateSegmentDiscards	1.3.6.1.4.1.800.2.2.8.1.1.18	Counter	read-only	The number of frames that have been discarded by this virtual port because the routing descriptor field contained a duplicate segment identifier.
CTR vSrHopCountExceededDiscards	1.3.6.1.4.1.800.2.2.8.1.1.19	Counter	read-only	The number of explorer frames that have been discarded by this virtual port because the Routing Information Field has exceeded the maximum route descriptor length.
CTR vSrDupLanIdOrTreeErrors	1.3.6.1.4.1.800.2.2.8.1.1.20	Counter	read-only	The number of duplicate LAN IDs or Tree errors. This helps in detection of problems in networks containing older IBM Source Routing Bridges.
CTR vSrLanIdMismatches	1.3.6.1.4.1.800.2.2.8.1.1.21	Counter	read-only	The number of ARE and STE frames that were discarded because the last LAN ID in the routing information field did not equal the LAN-in ID. This error can occur in implementations which do only a LAN-in ID and Bridge Number check instead of a LAN-in ID, Bridge Number, and LAN-out ID check before they forward broadcast frames.
INT vSrBridgeLfMode	1.3.6.1.4.1.800.2.2.8.1.1.22	INTEGER	read-only	Indicates whether the bridge operates using older 3 bit length negotiation fields or the newer 6 bit length field in its RIF.
INT vSrPortType	1.3.6.1.4.1.800.2.2.8.1.1.23	INTEGER	read-write	Indicates whether this port is a SRT or SR only SRT = 1 SR = 2
INT vSrAREblock	1.3.6.1.4.1.800.2.2.8.1.1.24	INTEGER	read-write	Indicates whether this port would treat ARE frames exactly like STE frames which would be blocked if the Spanning Tree mode is blocking. 1 - this port would not block ARE. 2 - this port would block ARE.
INT vSrHopCountIn	1.3.6.1.4.1.800.2.2.8.1.1.25	INTEGER	read-write	The maximum number of routing descriptors allowed in an inbound All Paths or Spanning Tree Explorer frames.
INT vSrSapDenyFilter1	1.3.6.1.4.1.800.2.2.8.1.1.26	INTEGER	read-write	Packets with this SAP value are to be discarded.
INT vSrSapDenyFilter2	1.3.6.1.4.1.800.2.2.8.1.1.27	INTEGER	read-write	Packets with this SAP value are to be discarded.
INT vSrSapPermitFilter1	1.3.6.1.4.1.800.2.2.8.1.1.28	INTEGER	read-write	Packets without this SAP value are to be discarded.
INT vSrSapPermitFilter2	1.3.6.1.4.1.800.2.2.8.1.1.29	INTEGER	read-write	Packets without this SAP value are to be discarded.
INT vSrSapFilterEnable	1.3.6.1.4.1.800.2.2.8.2	INTEGER	read-write	A scalar value to enable or disable the SAP filtering feature in this source route switch.
vTrunking	1.3.6.1.4.1.800.2.2.9
vTrunkingServicesTable	1.3.6.1.4.1.800.2.2.9.1		not-accessible	A list of commands to add or remove Virtual LANs from a trunking service.
vTrunkingServicesEntry	1.3.6.1.4.1.800.2.2.9.1.1		not-accessible	A trunking services entry.
INT vTrunkingServicesSlot	1.3.6.1.4.1.800.2.2.9.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the trunking service.
INT vTrunkingServicesStation	1.3.6.1.4.1.800.2.2.9.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the trunking service.
STR vTrunkingServicesDescription	1.3.6.1.4.1.800.2.2.9.1.1.3	DisplayString	read-write	A description of the trunking service being provided.
INT vTrunkingServicesBridgeID	1.3.6.1.4.1.800.2.2.9.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given trunking service. A value of 0 means that the Virtual Bridge port does not exist.
vTrunkingVlanTable	1.3.6.1.4.1.800.2.2.9.2		not-accessible	A list of commands to add or remove Virtual LANs from a trunking service.
vTrunkingVlanEntry	1.3.6.1.4.1.800.2.2.9.2.1		not-accessible	A trunking Virtual LAN entry.
INT vTrunkingSlot	1.3.6.1.4.1.800.2.2.9.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the trunking service.
INT vTrunkingStation	1.3.6.1.4.1.800.2.2.9.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the trunking service.
INT vTrunkingLanNumber	1.3.6.1.4.1.800.2.2.9.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given trunking service.
INT vTrunkingCommand	1.3.6.1.4.1.800.2.2.9.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given trunking service.
vAutoTracker	1.3.6.1.4.1.800.2.2.10
atportRuleTable	1.3.6.1.4.1.800.2.2.10.1		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
atportRuleEntry	1.3.6.1.4.1.800.2.2.10.1.1		not-accessible	An entry in the atportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
INT atportRuleGroupId	1.3.6.1.4.1.800.2.2.10.1.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atportRuleVLANId	1.3.6.1.4.1.800.2.2.10.1.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
INT atportRuleIdx	1.3.6.1.4.1.800.2.2.10.1.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
OCT atportRulePortId	1.3.6.1.4.1.800.2.2.10.1.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
INT atportRulePortState	1.3.6.1.4.1.800.2.2.10.1.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atMacRuleTable	1.3.6.1.4.1.800.2.2.10.2		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atMacRuleEntry	1.3.6.1.4.1.800.2.2.10.2.1		not-accessible	An entry in the atMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
INT atMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.2.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.2.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
INT atMacRuleIndex	1.3.6.1.4.1.800.2.2.10.2.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
MAC atMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.2.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
INT atMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.2.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atProtoRuleTable	1.3.6.1.4.1.800.2.2.10.3		not-accessible	This table is used to configure an Auto-Tracker VLAN based on Protocol Rule. Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atProtoRuleEntry	1.3.6.1.4.1.800.2.2.10.3.1		not-accessible	An entry in the atProtoRuleTable.
INT atProtoRuleGroupId	1.3.6.1.4.1.800.2.2.10.3.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is defined.
INT atProtoRuleVLANId	1.3.6.1.4.1.800.2.2.10.3.1.2	INTEGER	read-write	This object is the VLAN Id defined by this Protocol-rule.
INT atProtoRuleIndex	1.3.6.1.4.1.800.2.2.10.3.1.3	INTEGER	read-write	This object specifies the exact protocol rule for this VLAN. On creating a VLAN based on protocol rule, this object must be set to 0.
OCT atProtoRule	1.3.6.1.4.1.800.2.2.10.3.1.4	OCTET STRING	read-write	This object is an octet string of length 5 bytes. This object specifies the protocol type that defines this vlan. The values for the different protocols are: IP - first byte = 1, IPX - first byte = 2, AppleTalk - first byte = 3, DECNet - first byte = 4, Note that, in case of IP, ARP is included as IP and need not be specified explicitly. Similarly when AppleTalk is chosen both DDP and AARP are included. If any other protocol is used, it can be defined either by using Ether-type - first byte = 5 specifying its ether-type, second and third byte = ether-type value in hex. DSAP and SSAP - first byte = 6 specifying that its SAP type second byte = DSAP, third byte = SSAP in hex. SNAP Type - first byte = 7 specifying its SNAP second through sixth byte = snap value in hex.
INT atProtoRuleStatus	1.3.6.1.4.1.800.2.2.10.3.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atNetRuleTable	1.3.6.1.4.1.800.2.2.10.4		not-accessible	This table is used to configure an Auto-Tracker VLAN based on Net Addr Rule. Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atNetRuleEntry	1.3.6.1.4.1.800.2.2.10.4.1		not-accessible	An entry in the atNetRuleTable. A VLAN can be defined using exaclty one address only except in the case of IPX where it could either be a Network number or the encapsulation.
INT atNetRuleGroupId	1.3.6.1.4.1.800.2.2.10.4.1.1	INTEGER	read-write	This object indicates the VLAN Group in which this VLAN is defined.
INT atNetRuleVLANId	1.3.6.1.4.1.800.2.2.10.4.1.2	INTEGER	read-write	This object is the VLAN Id for this NetAddr-rule based vlan.
INT atNetRuleIndex	1.3.6.1.4.1.800.2.2.10.4.1.3	INTEGER	read-write	This object specifies the exact Network Address rule for this VLAN. When creating a VLAN using the Network Address rule, this object must be set to 0.
INT atNetRuleProtocolId	1.3.6.1.4.1.800.2.2.10.4.1.4	INTEGER	read-write	This object indicates which protocols Network Address is used to define this VLAN.
OCT atNetRuleNetAddr	1.3.6.1.4.1.800.2.2.10.4.1.5	OCTET STRING	read-write	This object gives the network address that defines this vlan. If the protocol is IP, this object contains the four bytes of IP address followed by four bytes of IP Subnet Mask. If the protocol is IPX, this object contains the four bytes of Network Number followed by one byte of encapsulation type used on that network. The values for the encapsulation types are: byte 5 = 1 - IPX 802.3 encapsulation byte 5 = 2 - IPX Ethernet2 encapsulation byte 5 = 3 - IPX LLC encapsulation byte 5 = 4 - IPX SNAP encapsulation If the protocol is DECNet, this object contains the one byte of DEC area.
INT atNetRuleStatus	1.3.6.1.4.1.800.2.2.10.4.1.6	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atUserRuleTable	1.3.6.1.4.1.800.2.2.10.5		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a User Defined Rule.Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atUserRuleEntry	1.3.6.1.4.1.800.2.2.10.5.1		not-accessible	An entry in the atUserRuleTable. A VLAN can be defined by more than one rule. In that case, the device will belong to that VLAN if it matches atleast one of the rules defined for that VLAN.
INT atUserRuleGroupId	1.3.6.1.4.1.800.2.2.10.5.1.1	INTEGER	read-write	This object indicates the VLAN Group in which this VLAN is defined.
INT atUserRuleVLANId	1.3.6.1.4.1.800.2.2.10.5.1.2	INTEGER	read-write	This object is the VLAN Id for this User-rule based vlan.
INT atUserRuleIndex	1.3.6.1.4.1.800.2.2.10.5.1.3	INTEGER	read-write	This object indicates the exact User defined rule for this VLAN. When creating a VLAN using the user defined rules, this object must be set to 0.
INT atUserRuleOffset	1.3.6.1.4.1.800.2.2.10.5.1.4	INTEGER	read-write	This object defines the offset into a frame where the pattern to match is located. This offset is relative to the start of the MAC header.
OCT atUserRuleValue	1.3.6.1.4.1.800.2.2.10.5.1.5	OCTET STRING	read-write	This object defines the value of the pattern to match in a frame. The maximum length of this value can be 8 octets and the associated mask should have the same length as this object.
OCT atUserRuleMask	1.3.6.1.4.1.800.2.2.10.5.1.6	OCTET STRING	read-write	This object defines the mask for the pattern to match. The Mask can be upto 8 bytes long but has to be of the same length as the Value.
INT atUserRuleStatus	1.3.6.1.4.1.800.2.2.10.5.1.7	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
atVLANRuleSumTable	1.3.6.1.4.1.800.2.2.10.6		not-accessible	This table provides the summary of vlan rule configuration.
atVLANRuleSumEntry	1.3.6.1.4.1.800.2.2.10.6.1		not-accessible	An entry in the vlan summary table.
INT atVLANRuleSumGroupId	1.3.6.1.4.1.800.2.2.10.6.1.1	INTEGER	read-only	The group to which the VLAN belongs.
INT atVLANRuleSumVLANId	1.3.6.1.4.1.800.2.2.10.6.1.2	INTEGER	read-only	The VLAN Id for this rule is defined.
INT atVLANRuleIndex	1.3.6.1.4.1.800.2.2.10.6.1.3	INTEGER	read-only	The exact rule identifier for this rule.
INT atVLANRuleSubIndex	1.3.6.1.4.1.800.2.2.10.6.1.4	INTEGER	read-only	In case a VLAN is defined using multiple instances of the same type of rule, this object identifies the exact instance of that type of rule. This object could then be used along with the group and vlanid to get the complete definition of this rule from the appropriate rule table.
INT atVLANRuleType	1.3.6.1.4.1.800.2.2.10.6.1.5	INTEGER	read-only	The type of rule. This object can then be used to decide which table to lookup for the complete definition of the rule.
atVLANControlTable	1.3.6.1.4.1.800.2.2.10.7		not-accessible	This table gives the control information about all Auto-Tracker VLANs.
atVLANControlEntry	1.3.6.1.4.1.800.2.2.10.7.1		not-accessible	An entry in the control table.
INT atVLANGroupId	1.3.6.1.4.1.800.2.2.10.7.1.1	INTEGER	read-write	This is the VLAN group to which the VLAN belongs.
INT atVLANId	1.3.6.1.4.1.800.2.2.10.7.1.2	INTEGER	read-write	The VLAN id for this VLAN.
STR atVLANDesc	1.3.6.1.4.1.800.2.2.10.7.1.3	DisplayString	read-write	The description for this vlan.
INT atVLANAdminStatus	1.3.6.1.4.1.800.2.2.10.7.1.4	INTEGER	read-write	The Admin status of the VLAN. If set to disabled, any rules configured for this vlan will no longer be used and their status will be changed to disabled.
INT atVLANOperStatus	1.3.6.1.4.1.800.2.2.10.7.1.5	INTEGER	read-only	The operation status of this vlan. If there any devices learnt by this system on this vlan, the operation status of the vlan is said to be active.
INT atDefaultVlan	1.3.6.1.4.1.800.2.2.10.8	INTEGER	read-write	When set to on, it allows devices to be assigned to the default vlan, else if it set to off, such devices are not assigned to any vlan, thereby preventing them from communicating to other devices.
atmcportRuleTable	1.3.6.1.4.1.800.2.2.10.9		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
atmcportRuleEntry	1.3.6.1.4.1.800.2.2.10.9.1		not-accessible	An entry in the atportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
INT atmcportRuleGroupId	1.3.6.1.4.1.800.2.2.10.9.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atmcportRuleVLANId	1.3.6.1.4.1.800.2.2.10.9.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
INT atmcportRuleIdx	1.3.6.1.4.1.800.2.2.10.9.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
OCT atmcportRulePortId	1.3.6.1.4.1.800.2.2.10.9.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
INT atmcportRulePortState	1.3.6.1.4.1.800.2.2.10.9.1.5	INTEGER	read-write	This object determines whether the port is being added or deleted from this port rule definition.
atmcMacRuleTable	1.3.6.1.4.1.800.2.2.10.10		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atmcMacRuleEntry	1.3.6.1.4.1.800.2.2.10.10.1		not-accessible	An entry in the atmcMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
INT atmcMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.10.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atmcMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.10.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
INT atmcMacRuleIndex	1.3.6.1.4.1.800.2.2.10.10.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
MAC atmcMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.10.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
INT atmcMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.10.1.5	INTEGER	read-write	This object determines if the MAC address is included in the VLAN definition. If the object is set to disabled, the MAC address is removed from the VLAN definition.
atMcastRuleTable	1.3.6.1.4.1.800.2.2.10.11		not-accessible	This table is used to configure MCAST Rules for a VLAN.
atMcastRuleEntry	1.3.6.1.4.1.800.2.2.10.11.1		not-accessible	An entry in the MCAST Rule table.
INT atMcastRuleGroupId	1.3.6.1.4.1.800.2.2.10.11.1.1	INTEGER	read-write	The group in which this rule is defined.
INT atMcastRuleVLANId	1.3.6.1.4.1.800.2.2.10.11.1.2	INTEGER	read-write	The VLAN for which this rule is defined.
INT atMcastRuleIndex	1.3.6.1.4.1.800.2.2.10.11.1.3	INTEGER	read-write	The rule index ( a vlan can have multiple rules defined ) which exactly identifies this rule.
MAC atMcastRuleMacAddress	1.3.6.1.4.1.800.2.2.10.11.1.4	MacAddress	read-write	The Multicast MAC Address that makes up this rule.
INT atMcastRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.11.1.5	INTEGER	read-write	The admin-state of this multicast mac address.
atmcVLANRuleSumTable	1.3.6.1.4.1.800.2.2.10.12		not-accessible	This table provides the summary of vlan rule configuration.
atmcVLANRuleSumEntry	1.3.6.1.4.1.800.2.2.10.12.1		not-accessible	An entry in the vlan summary table.
INT atmcVLANRuleSumGroupId	1.3.6.1.4.1.800.2.2.10.12.1.1	INTEGER	read-only	The group to which the VLAN belongs.
INT atmcVLANRuleSumVLANId	1.3.6.1.4.1.800.2.2.10.12.1.2	INTEGER	read-only	The VLAN Id for this rule is defined.
INT atmcVLANRuleIndex	1.3.6.1.4.1.800.2.2.10.12.1.3	INTEGER	read-only	The exact rule identifier for this rule.
INT atmcVLANRuleSubIndex	1.3.6.1.4.1.800.2.2.10.12.1.4	INTEGER	read-only	In case a VLAN is defined using multiple instances of the same type of rule, this object identifies the exact instance of that type of rule. This object could then be used along with the group and vlanid to get the complete definition of this rule from the appropriate rule table.
INT atmcVLANRuleType	1.3.6.1.4.1.800.2.2.10.12.1.5	INTEGER	read-only	The type of rule. This object can then be used to decide which table to lookup for the complete definition of the rule.
atmcVLANControlTable	1.3.6.1.4.1.800.2.2.10.13		not-accessible	This table gives the control information about all Auto-Tracker VLANs.
atmcVLANControlEntry	1.3.6.1.4.1.800.2.2.10.13.1		not-accessible	An entry in the control table.
INT atmcVLANGroupId	1.3.6.1.4.1.800.2.2.10.13.1.1	INTEGER	read-write	This is the VLAN group to which the VLAN belongs.
INT atmcVLANId	1.3.6.1.4.1.800.2.2.10.13.1.2	INTEGER	read-write	The VLAN id for this VLAN.
STR atmcVLANDesc	1.3.6.1.4.1.800.2.2.10.13.1.3	DisplayString	read-write	The description for this vlan.
INT atmcVLANAdminStatus	1.3.6.1.4.1.800.2.2.10.13.1.4	INTEGER	read-write	The Admin status of the VLAN. If set to disabled, any rules configured for this vlan will no longer be used and their status will be changed to disabled.
INT atmcVLANOperStatus	1.3.6.1.4.1.800.2.2.10.13.1.5	INTEGER	read-only	The operation status of this vlan. If there any devices learnt by this system on this vlan, the operation status of the vlan is said to be active.
gmAutoServiceTable	1.3.6.1.4.1.800.2.2.10.14		not-accessible	Table of Auto-Activated Services
gmAutoServiceEntry	1.3.6.1.4.1.800.2.2.10.14.1		not-accessible	an entry in the table
INT gmAutoServiceGroupId	1.3.6.1.4.1.800.2.2.10.14.1.1	INTEGER	read-write	Group for which this service is configured
INT gmAutoServicePrimarySlot	1.3.6.1.4.1.800.2.2.10.14.1.2	INTEGER	read-write	Primary slot on which this service will be activated.
INT gmAutoServicePrimaryPort	1.3.6.1.4.1.800.2.2.10.14.1.3	INTEGER	read-write	Primary port on which this service will be activated.
INT gmAutoServiceIndex	1.3.6.1.4.1.800.2.2.10.14.1.4	INTEGER	read-write	Service index associated with this service
INT gmAutoServiceType	1.3.6.1.4.1.800.2.2.10.14.1.5	INTEGER	read-write	Type of this service - currently only lane is supported and this object should have a value of 1.
STR gmAutoServiceName	1.3.6.1.4.1.800.2.2.10.14.1.6	DisplayString	read-write	The name of the service. In case of LANE, this is the elan name.
INT gmAutoServiceSecondarySlot	1.3.6.1.4.1.800.2.2.10.14.1.7	INTEGER	read-write	Secondary slot on which this service will be activated.
INT gmAutoServiceSecondaryPort	1.3.6.1.4.1.800.2.2.10.14.1.8	INTEGER	read-write	Secondary port on which this service will be activated.
INT gmAutoServiceAdminState	1.3.6.1.4.1.800.2.2.10.14.1.9	INTEGER	read-write	The admin state of this service
INT gmAutoServiceOperState	1.3.6.1.4.1.800.2.2.10.14.1.10	INTEGER	read-write	Operational state of this service.
INT gmAutoServiceActiveSlot	1.3.6.1.4.1.800.2.2.10.14.1.11	INTEGER	read-only	Slot on the which the service is currently active.
INT gmAutoServiceActivePort	1.3.6.1.4.1.800.2.2.10.14.1.12	INTEGER	read-only	Physical Port on the which the service is currently active.
INT gmAutoServiceNumber	1.3.6.1.4.1.800.2.2.10.14.1.13	INTEGER	read-only	Service number assigned by the switch when this service is activated.
INT gmAutoServiceTranslations	1.3.6.1.4.1.800.2.2.10.14.1.14	INTEGER	read-write	This parameter controls whether frame translations will be exercised for this lane service once activated.
atBindRuleTable	1.3.6.1.4.1.800.2.2.10.16		not-accessible	The Binding Rule table.
atBindRuleEntry	1.3.6.1.4.1.800.2.2.10.16.1		not-accessible	An entry in the Binding Rule Table.
INT atBindRuleGroupId	1.3.6.1.4.1.800.2.2.10.16.1.1	INTEGER	read-write	The group id of the vlan for which this rule is configured.
INT atBindRuleVlanId	1.3.6.1.4.1.800.2.2.10.16.1.2	INTEGER	read-write	The vlan id for which this rule is configured.
INT atBindRuleIndex	1.3.6.1.4.1.800.2.2.10.16.1.3	INTEGER	read-write	The index which uniquely identifies this rule for this vlan.
OCT atBindRulePortId	1.3.6.1.4.1.800.2.2.10.16.1.4	OCTET STRING	read-write	The port ( slot/intf/srvc/inst) for which this binding is configured.
IP atBindRuleIPAddress	1.3.6.1.4.1.800.2.2.10.16.1.5	IpAddress	read-write	The IP address for which this binding is configured.
MAC atBindRuleMacAddress	1.3.6.1.4.1.800.2.2.10.16.1.6	MacAddress	read-write	The mac address for which this binding is configured.
OCT atBindRuleProtocol	1.3.6.1.4.1.800.2.2.10.16.1.7	OCTET STRING	read-write	The protocol for which this binding is configured.
INT atBindRuleBindParameter	1.3.6.1.4.1.800.2.2.10.16.1.8	INTEGER	read-write	The parameters to bind together.
INT atBindRuleStatus	1.3.6.1.4.1.800.2.2.10.16.1.9	INTEGER	read-write	The admin status for this rule.
gmGroupListTable	1.3.6.1.4.1.800.2.2.10.17		not-accessible	This table lists the groups on a port.
gmGroupListEntry	1.3.6.1.4.1.800.2.2.10.17.1		not-accessible	An entry in the Group List table.
INT gmGroupListPortSlot	1.3.6.1.4.1.800.2.2.10.17.1.1	INTEGER	read-only	The slot id of the port for which the group list is requested.
INT gmGroupListPortInterface	1.3.6.1.4.1.800.2.2.10.17.1.2	INTEGER	read-only	The physical port number for which the group list is requested.
INT gmGroupListGroupId	1.3.6.1.4.1.800.2.2.10.17.1.3	INTEGER	read-only	One of the Groups to which the port belongs.
atDHCPportRuleTable	1.3.6.1.4.1.800.2.2.10.18		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
atDHCPportRuleEntry	1.3.6.1.4.1.800.2.2.10.18.1		not-accessible	An entry in the atDHCPportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
INT atDHCPportRuleGroupId	1.3.6.1.4.1.800.2.2.10.18.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atDHCPportRuleVLANId	1.3.6.1.4.1.800.2.2.10.18.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
INT atDHCPportRuleIdx	1.3.6.1.4.1.800.2.2.10.18.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
OCT atDHCPportRulePortId	1.3.6.1.4.1.800.2.2.10.18.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
INT atDHCPportRulePortState	1.3.6.1.4.1.800.2.2.10.18.1.5	INTEGER	read-write	This object determines whether the port is being added or deleted from this port rule definition.
atDHCPMacRuleTable	1.3.6.1.4.1.800.2.2.10.19		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atDHCPMacRuleEntry	1.3.6.1.4.1.800.2.2.10.19.1		not-accessible	An entry in the atDHCPMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
INT atDHCPMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.19.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atDHCPMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.19.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
INT atDHCPMacRuleIndex	1.3.6.1.4.1.800.2.2.10.19.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
MAC atDHCPMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.19.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
INT atDHCPMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.19.1.5	INTEGER	read-write	This object determines if the MAC address is included in the VLAN definition. If the object is set to disabled, the MAC address is removed from the VLAN definition.
INT groupMobilityStatus	1.3.6.1.4.1.800.2.2.10.20	INTEGER	read-write	This object can used to configure the global status of group-mobility feature on the switch.
INT gmMoveToDefGroup	1.3.6.1.4.1.800.2.2.10.21	INTEGER	read-write	When this object is set on, the switch will remove the port of out of a mobile group when the last device in that group learnt on that port ages out due to inactivity. When it is set to off, the port will remain in such a group, even if all macs leant on that port in that group age out.
INT gmDefGroup	1.3.6.1.4.1.800.2.2.10.22	INTEGER	read-write	When this object is set to on, the switch will assign the port's default group id to all such devices which are learned and do not match any policies for mobile groups. If it is set to off, such devices will get assigned to no groups and the traffic they send will be discarded by the switch.
atvIPRouterInfo	1.3.6.1.4.1.800.2.2.11
atvIPRouterTable	1.3.6.1.4.1.800.2.2.11.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
atvIPRouterEntry	1.3.6.1.4.1.800.2.2.11.1.1		not-accessible	A VLAN entry.
INT atvIPRouterVLanGroup	1.3.6.1.4.1.800.2.2.11.1.1.1	INTEGER	read-write	VLAN Group ID for this atvIPRouterEntry instance.
INT atvIPRouterVLan	1.3.6.1.4.1.800.2.2.11.1.1.2	INTEGER	read-write	Auto Tracker VLAN Id for this router port instance.
OCT atvIPRouterProtocol	1.3.6.1.4.1.800.2.2.11.1.1.3	OCTET STRING	read-write	The routing protocol(s) for this virtual router port. Each IP router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipOther(1), ipRip(2), ipEgp(4), ipGgp(8), ipHello(16), ipIs-is(32), ipEs-is(64), ipCiscoIgrp(128), ipBbnSpfIgp(256), ipOigp(512)
IP atvIPRouterNetAddress	1.3.6.1.4.1.800.2.2.11.1.1.4	IpAddress	read-write	The IP network address for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP atvIPRouterSubNetMask	1.3.6.1.4.1.800.2.2.11.1.1.5	IpAddress	read-write	The IP network subnet mask for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP atvIPRouterBcastAddress	1.3.6.1.4.1.800.2.2.11.1.1.6	IpAddress	read-write	The IP broadcast address for this virtual bridge instance for the purpose of allowing access from the external network management system.
STR atvIPRouterDescription	1.3.6.1.4.1.800.2.2.11.1.1.7	DisplayString	read-write	Textual description of the router instance.
XYL atvIPRouterAdmStatus	1.3.6.1.4.1.800.2.2.11.1.1.8	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enable(2) or disable(1) (or delete (3)) upon user's request.
XYL atvIPRouterOperStatus	1.3.6.1.4.1.800.2.2.11.1.1.9	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
INT atvIPRouterFramingType	1.3.6.1.4.1.800.2.2.11.1.1.10	INTEGER	read-write	Provides the ability to set the outbound frame type for IP traffic. The default frame type is Ethernet 2. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
INT atvIPRouterRipConfigMode	1.3.6.1.4.1.800.2.2.11.1.1.11	INTEGER	read-write	RIP's operational mode. 'silent' means that RIP listens for routing updates but does not send them. 'deaf' means that RIP sends routing updates but not listen to them. 'active' means that RIP both sends and receives routing updates, and 'inactive' means that RIP is not operational on the given virtual LAN. The default is 'simple'.
INT atvIPRouterRelayServicesFwd	1.3.6.1.4.1.800.2.2.11.1.1.12	INTEGER	read-write	Each of the 8 least significant bits are assigned to a UDP Relay service as follows: 01H - bootp (Not currently allowed) 02H - NBNS 04H - NBDD 08H - Gen1 10H - Gen2 20H - Gen3 40H - Gen4 80H - Gen5 A set bit indicates that packets are being forwarded to this vlan for the service corresponding to the bit. Use bit 15 to indicate that a UDP Relay Service should be unset and packets should not be forwarded to this vlan. 8001H - bootp (Not currently allowed) 8002H - NBNS 8004H - NBDD 8008H - Gen1 8010H - Gen2 8020H - Gen3 8040H - Gen4 8080H - Gen5
atvIPXRouterInfo	1.3.6.1.4.1.800.2.2.12
atvIPXRouterTable	1.3.6.1.4.1.800.2.2.12.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
atvIPXRouterEntry	1.3.6.1.4.1.800.2.2.12.1.1		not-accessible	A VLAN entry.
INT atvIPXRouterVLanGroup	1.3.6.1.4.1.800.2.2.12.1.1.1	INTEGER	read-write	VLAN Group ID for this vIPXRouterEntry instance.
INT atvIPXRouterVLan	1.3.6.1.4.1.800.2.2.12.1.1.2	INTEGER	read-write	VLAN ID for this vIPXRouterEntry instance.
INT atvIPXRouterProtocol	1.3.6.1.4.1.800.2.2.12.1.1.3	INTEGER	read-write	The routing protocol(s) for this virtual router port. Each IPX router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipxOther(1), ipxRip(2), ipxSap(4)
NET atvIPXRouterNetAddress	1.3.6.1.4.1.800.2.2.12.1.1.4	NetNumber	read-write	The IPX network address for this virtual bridge.
INT atvIPXRouterFramingType	1.3.6.1.4.1.800.2.2.12.1.1.5	INTEGER	read-write	Provides the ability to set the outbound frame type for IPX traffic. The default frame type is 802.2 Novell Raw. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
STR atvIPXRouterDescription	1.3.6.1.4.1.800.2.2.12.1.1.6	DisplayString	read-write	Textual description of the router instance.
XYL atvIPXRouterAdmStatus	1.3.6.1.4.1.800.2.2.12.1.1.7	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enabled(2) or disabled(1) upon user's request.
XYL atvIPXRouterOperStatus	1.3.6.1.4.1.800.2.2.12.1.1.8	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
INT atvIPXSrcRteType	1.3.6.1.4.1.800.2.2.12.1.1.9	INTEGER	read-write	Provide the ability to set the type of source routing broadcasts between AllRoutesExplorer(0) and SpanningTreeExplorer(1).
v80210	1.3.6.1.4.1.800.2.2.13
v80210ServicesTable	1.3.6.1.4.1.800.2.2.13.1		not-accessible	A list of commands to add or remove Virtual LANs from a 80210 service.
v80210ServicesEntry	1.3.6.1.4.1.800.2.2.13.1.1		not-accessible	A 80210 services entry.
INT v80210ServicesSlot	1.3.6.1.4.1.800.2.2.13.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the 80210 service.
INT v80210ServicesStation	1.3.6.1.4.1.800.2.2.13.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the 80210 service.
STR v80210ServicesDescription	1.3.6.1.4.1.800.2.2.13.1.1.3	DisplayString	read-write	A description of the 80210 service being provided.
INT v80210ServicesBridgeID	1.3.6.1.4.1.800.2.2.13.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given 80210 service. A value of 0 means that the Virtual Bridge port does not exist.
v80210VlanTable	1.3.6.1.4.1.800.2.2.13.2		not-accessible	A list of commands to add or remove Virtual LANs from a 80210 service.
v80210VlanEntry	1.3.6.1.4.1.800.2.2.13.2.1		not-accessible	A 80210trunking Virtual LAN entry.
INT v80210Slot	1.3.6.1.4.1.800.2.2.13.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the 80210 service.
INT v80210Station	1.3.6.1.4.1.800.2.2.13.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the 80210 service.
INT v80210LanNumber	1.3.6.1.4.1.800.2.2.13.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given 80210 service.
INT v80210Command	1.3.6.1.4.1.800.2.2.13.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given 80210 service.
vDBr	1.3.6.1.4.1.800.2.2.14
vDBrServicesTable	1.3.6.1.4.1.800.2.2.14.1		not-accessible	A list of commands to add or remove Virtual LANs from an DBr service.
vDBrServicesEntry	1.3.6.1.4.1.800.2.2.14.1.1		not-accessible	An DBr services entry.
INT vDBrServicesSlot	1.3.6.1.4.1.800.2.2.14.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the DBr service.
INT vDBrServicesStation	1.3.6.1.4.1.800.2.2.14.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the DBr service.
STR vDBrServicesDescription	1.3.6.1.4.1.800.2.2.14.1.1.3	DisplayString	read-write	A description of the DBr service being provided.
INT vDBrServicesBridgeID	1.3.6.1.4.1.800.2.2.14.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given DBr service. A value of 0 means that the Virtual Bridge port does not exist.
vDBrVlanTable	1.3.6.1.4.1.800.2.2.14.2		not-accessible	A list of commands to add or remove Virtual LANs from the DBr service.
vDBrVlanEntry	1.3.6.1.4.1.800.2.2.14.2.1		not-accessible	An DBr trunking Virtual LAN entry.
INT vDBrSlot	1.3.6.1.4.1.800.2.2.14.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the DBr service.
INT vDBrStation	1.3.6.1.4.1.800.2.2.14.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the DBr service.
INT vDBrLanNumber	1.3.6.1.4.1.800.2.2.14.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given DBr service.
INT vDBrCommand	1.3.6.1.4.1.800.2.2.14.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given DBr service.
v8021Q	1.3.6.1.4.1.800.2.2.15
qGroupTable	1.3.6.1.4.1.800.2.2.15.1		not-accessible	This table lists the 802.1q groups on a port.
qGroupEntry	1.3.6.1.4.1.800.2.2.15.1.1		not-accessible	An entry in 802.1q group table.
INT qGroupSlot	1.3.6.1.4.1.800.2.2.15.1.1.1	INTEGER	read-write	The slot id of the required port.
INT qGroupPort	1.3.6.1.4.1.800.2.2.15.1.1.2	INTEGER	read-write	The physical port number.
INT qGroupGroupId	1.3.6.1.4.1.800.2.2.15.1.1.3	INTEGER	read-write	Group Id on the particular port.
INT qGroupMode	1.3.6.1.4.1.800.2.2.15.1.1.4	INTEGER	read-write	gstsxylan(1) indicates spanning tree support on a gigabit port by proprietary mode and gstsieee(2) indicates spanning tree on a gigabit port by IEEE mode, msts(3) indicates multiple spanning tree support on a 10/100 Mammoth Ethernet port, and ssts(4) indicates single spanning tree support on a 10/100 Mammoth Ethernet port.
STR qGroupDescription	1.3.6.1.4.1.800.2.2.15.1.1.5	DisplayString	read-write	Textual description of multiple spanning tree.
INT qGroupTag	1.3.6.1.4.1.800.2.2.15.1.1.6	INTEGER	read-write	Tag used for support multiple spanning tree.
INT qGroupPriority	1.3.6.1.4.1.800.2.2.15.1.1.7	INTEGER	read-write	Priority used for support multiple spanning tree.
INT qGroupAdminStatus	1.3.6.1.4.1.800.2.2.15.1.1.8	INTEGER	read-write	Value of 0 indicates the service should be deleted, value of 1 indicates the service should be created.
CTR qGroupTxPkts	1.3.6.1.4.1.800.2.2.15.1.1.9	Counter	read-only	Gives the number of transmitteded packets.
CTR qGroupRxPkts	1.3.6.1.4.1.800.2.2.15.1.1.10	Counter	read-only	Gives the number of received packets.
CTR qGroupTxOctets	1.3.6.1.4.1.800.2.2.15.1.1.11	Counter	read-only	Gives the number of transmitted bytes.
CTR qGroupRxOctets	1.3.6.1.4.1.800.2.2.15.1.1.12	Counter	read-only	Gives the number of received bytes.
vDupMac	1.3.6.1.4.1.800.2.2.16
MAC vDupMacMac	1.3.6.1.4.1.800.2.2.16.1	MacAddress	read-only	The router port's MAC address for which the last duplicate MAC address was detected .
INT vDupMacSlot	1.3.6.1.4.1.800.2.2.16.2	INTEGER	read-only	The slot number (1-based) where duplicate MAC address was last received.
INT vDupMacIntf	1.3.6.1.4.1.800.2.2.16.3	INTEGER	read-only	The interface number (1-based) where duplicate MAC address was last received.
INT vDupMacTime	1.3.6.1.4.1.800.2.2.16.4	INTEGER	read-only	The time in seconds that the duplicate MAC address was detected.
vPmap	1.3.6.1.4.1.800.2.2.17
vPmapIngressTable	1.3.6.1.4.1.800.2.2.17.1		not-accessible	A list of Port Mapping Ingress port table instance on this physical OmniSwitch or OSR.
vPmapIngressEntry	1.3.6.1.4.1.800.2.2.17.1.1		not-accessible	A Port Mapping Ingress Port entry.
INT pMapIngressId	1.3.6.1.4.1.800.2.2.17.1.1.1	INTEGER	read-write	A unique number that identifies this Port Mapping on the OmniSwitch or OSR.
INT pMapIngressSlot	1.3.6.1.4.1.800.2.2.17.1.1.2	INTEGER	read-write	A physical slot number on which the Port Mapping Ingress Port is configured.
INT pMapIngressPort	1.3.6.1.4.1.800.2.2.17.1.1.3	INTEGER	read-write	A physical port number that is associated with the Port Mapping Ingress Port.
INT pMapIngressSrvc	1.3.6.1.4.1.800.2.2.17.1.1.4	INTEGER	read-write	A service type that is associated with this Port Mapping Ingress Port.
INT pMapIngressInst	1.3.6.1.4.1.800.2.2.17.1.1.5	INTEGER	read-write	A Instance that is associated with this Port Mapping Ingress Port.
INT pMapIngressAdminStatus	1.3.6.1.4.1.800.2.2.17.1.1.6	INTEGER	read-write	This object indicates whether to add(1) to or delete(2) from the Port Mapping Ingress List.
vPmapEgressTable	1.3.6.1.4.1.800.2.2.17.2		not-accessible	A list of Port Mapping Egress port table instance on this physical OmniSwitch or OSR.
vPmapEgressEntry	1.3.6.1.4.1.800.2.2.17.2.1		not-accessible	A Port Mapping Egress Port entry.
INT pMapEgressId	1.3.6.1.4.1.800.2.2.17.2.1.1	INTEGER	read-write	A unique number that identifies this Port Mapping on the physical OmniSwitch or OSR.
INT pMapEgressSlot	1.3.6.1.4.1.800.2.2.17.2.1.2	INTEGER	read-write	A physical slot number on whitch the Port Mapping Egress Port is configured.
INT pMapEgressPort	1.3.6.1.4.1.800.2.2.17.2.1.3	INTEGER	read-write	A physical port number that is associated with the Port Mapping Egress Port.
INT pMapEgressSrvc	1.3.6.1.4.1.800.2.2.17.2.1.4	INTEGER	read-write	A service type that is associated with this Port Mapping Egress Port.
INT pMapEgressInst	1.3.6.1.4.1.800.2.2.17.2.1.5	INTEGER	read-write	A Instance that is associated with this Port Mapping Egress Port.
INT pMapEgressAdminStatus	1.3.6.1.4.1.800.2.2.17.2.1.6	INTEGER	read-write	This object indicates whether to add(1) to or delete(2) from the Port Mapping Egress Port.
vPmapConfigTable	1.3.6.1.4.1.800.2.2.17.3		not-accessible	A list of Port Mapping config table instance on this physical OmniSwitch or OSR.
vPmapConfigEntry	1.3.6.1.4.1.800.2.2.17.3.1		not-accessible	A Port Mapping configuration table entry.
INT pMapConfigId	1.3.6.1.4.1.800.2.2.17.3.1.1	INTEGER	read-only	A unique number that identifies this Port Mapping with the physical OmniSwitch or OSR.
INT pMapConfigStatus	1.3.6.1.4.1.800.2.2.17.3.1.2	INTEGER	read-write	This object indicates whether to set (1) or delete (2) the port mapping configeration..
INT vPmapNextId	1.3.6.1.4.1.800.2.2.17.4	INTEGER	read-only	The unique number that identifiers the next Port Mapping Table.

BridgeId (4)
BRI vStpBridgeAddress	1.3.6.1.4.1.800.2.2.5.3	BridgeId	read-only	The bridge identifier of this VLAN of the spanning tree as determined by the Spanning Tree Protocol as executed by this VLAN.
BRI vStpDesignatedRoot	1.3.6.1.4.1.800.2.2.5.6	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this VLAN. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
BRI vStpPortDesignatedBridge	1.3.6.1.4.1.800.2.2.5.19.1.11	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
BRI vStpPortDesignatedRoot	1.3.6.1.4.1.800.2.2.5.19.1.9	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Counter (28)
CTR qGroupRxOctets	1.3.6.1.4.1.800.2.2.15.1.1.12	Counter	read-only	Gives the number of received bytes.
CTR qGroupRxPkts	1.3.6.1.4.1.800.2.2.15.1.1.10	Counter	read-only	Gives the number of received packets.
CTR qGroupTxOctets	1.3.6.1.4.1.800.2.2.15.1.1.11	Counter	read-only	Gives the number of transmitted bytes.
CTR qGroupTxPkts	1.3.6.1.4.1.800.2.2.15.1.1.9	Counter	read-only	Gives the number of transmitteded packets.
CTR vBrdgTpFdbLastSeenTime	1.3.6.1.4.1.800.2.2.4.3.1.10	Counter	read-only	The time since, the specific unicast MAC address for which the VLAN bridge has forwarding information was last seen.
CTR vBrdgTpLearnEntryDiscards	1.3.6.1.4.1.800.2.2.4.1	Counter	read-only	The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
CTR vRipBadAddr	1.3.6.1.4.1.800.2.2.7.1.1.9	Counter	read-only	The number of RIP packets received on this virtual LAN whose host portion of the source IP address is bad.
CTR vRipBadCommand	1.3.6.1.4.1.800.2.2.7.1.1.10	Counter	read-only	The number of RIP packets received on this virtual LAN whose command type was neither a request nor a response.
CTR vRipBadFamily	1.3.6.1.4.1.800.2.2.7.1.1.7	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a bad value for the family type.
CTR vRipBadMetric	1.3.6.1.4.1.800.2.2.7.1.1.8	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a bad value for a route's metric.
CTR vRipBadSize	1.3.6.1.4.1.800.2.2.7.1.1.4	Counter	read-only	The number of RIP packets received on this virtual LAN whose size was incorrect.
CTR vRipBadVersion	1.3.6.1.4.1.800.2.2.7.1.1.5	Counter	read-only	The number of RIP packets received on this virtual LAN whose version number was incorrect.
CTR vRipInPkts	1.3.6.1.4.1.800.2.2.7.1.1.2	Counter	read-only	The number of RIP routing updates and requests received on this virtual LAN.
CTR vRipNonZero	1.3.6.1.4.1.800.2.2.7.1.1.6	Counter	read-only	The number of RIP packets received on this virtual LAN which contained a non-zero value in one of the 'must be zero' fields.
CTR vRipOutPkts	1.3.6.1.4.1.800.2.2.7.1.1.3	Counter	read-only	The number of RIP routing updates and requests sent on this virtual LAN.
CTR vRipTransmitsFailed	1.3.6.1.4.1.800.2.2.7.1.1.13	Counter	read-only	The number of RIP routing updaates or requests that the OmniSwitch was unable to transmit.
CTR vSrApeInFrames	1.3.6.1.4.1.800.2.2.8.1.1.13	Counter	read-only	The number of All Paths Explorer frames, also referred to as All Routes Explorer frames, that have been received by this virtual port from its segment.
CTR vSrApeOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.14	Counter	read-only	The number of all Paths Explorer Frames, also referred to as All Routes Explorer frames, that have been transmitted by this virtual port on its segment.
CTR vSrDupLanIdOrTreeErrors	1.3.6.1.4.1.800.2.2.8.1.1.20	Counter	read-only	The number of duplicate LAN IDs or Tree errors. This helps in detection of problems in networks containing older IBM Source Routing Bridges.
CTR vSrDuplicateSegmentDiscards	1.3.6.1.4.1.800.2.2.8.1.1.18	Counter	read-only	The number of frames that have been discarded by this virtual port because the routing descriptor field contained a duplicate segment identifier.
CTR vSrHopCountExceededDiscards	1.3.6.1.4.1.800.2.2.8.1.1.19	Counter	read-only	The number of explorer frames that have been discarded by this virtual port because the Routing Information Field has exceeded the maximum route descriptor length.
CTR vSrInvalidRif	1.3.6.1.4.1.800.2.2.8.1.1.17	Counter	read-only	The number of explorer frames that have been discarded by this virtual port because the routing Information field contained an invalid value.
CTR vSrLanIdMismatches	1.3.6.1.4.1.800.2.2.8.1.1.21	Counter	read-only	The number of ARE and STE frames that were discarded because the last LAN ID in the routing information field did not equal the LAN-in ID. This error can occur in implementations which do only a LAN-in ID and Bridge Number check instead of a LAN-in ID, Bridge Number, and LAN-out ID check before they forward broadcast frames.
CTR vSrSpecInFrames	1.3.6.1.4.1.800.2.2.8.1.1.11	Counter	read-only	The number of Specifically Routed frames, also referred to as Source Routed Frames, that have been received from this virtual port's segment.
CTR vSrSpecOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.12	Counter	read-only	The number of Specifically Routed frames, also referred to as Source Routed Frames, that this virtual port has transmitted on its segment.
CTR vSrSteInFrames	1.3.6.1.4.1.800.2.2.8.1.1.15	Counter	read-only	The number of spanning tree explorer frames that have been received by this virtual port from its segment.
CTR vSrSteOutFrames	1.3.6.1.4.1.800.2.2.8.1.1.16	Counter	read-only	The number of spanning tree explorer frames that have been transmitted by this virtual port on its segment.
CTR vStpTopChanges	1.3.6.1.4.1.800.2.2.5.5	Counter	read-only	The total number of topology changes detected by this VLAN bridge since the management entity was last reset or initialized.
DisplayString (13)
STR atmcVLANDesc	1.3.6.1.4.1.800.2.2.10.13.1.3	DisplayString	read-write	The description for this vlan.
STR atvIPRouterDescription	1.3.6.1.4.1.800.2.2.11.1.1.7	DisplayString	read-write	Textual description of the router instance.
STR atvIPXRouterDescription	1.3.6.1.4.1.800.2.2.12.1.1.6	DisplayString	read-write	Textual description of the router instance.
STR atVLANDesc	1.3.6.1.4.1.800.2.2.10.7.1.3	DisplayString	read-write	The description for this vlan.
STR gmAutoServiceName	1.3.6.1.4.1.800.2.2.10.14.1.6	DisplayString	read-write	The name of the service. In case of LANE, this is the elan name.
STR qGroupDescription	1.3.6.1.4.1.800.2.2.15.1.1.5	DisplayString	read-write	Textual description of multiple spanning tree.
STR v80210ServicesDescription	1.3.6.1.4.1.800.2.2.13.1.1.3	DisplayString	read-write	A description of the 80210 service being provided.
STR vDBrServicesDescription	1.3.6.1.4.1.800.2.2.14.1.1.3	DisplayString	read-write	A description of the DBr service being provided.
STR vIPRouterDescription	1.3.6.1.4.1.800.2.2.2.1.1.6	DisplayString	read-write	Textual description of the router instance.
STR vIPRouterRelayDescription	1.3.6.1.4.1.800.2.2.2.2.1.6	DisplayString	read-write	This sets the service description for generic services. For other services, the description is fixed and may only be read.
STR vIPXRouterDescription	1.3.6.1.4.1.800.2.2.3.1.1.5	DisplayString	read-write	Textual description of the router instance.
STR vLanDescription	1.3.6.1.4.1.800.2.2.1.2.1.4	DisplayString	read-write	Textual description of the VLAN instance.
STR vTrunkingServicesDescription	1.3.6.1.4.1.800.2.2.9.1.1.3	DisplayString	read-write	A description of the trunking service being provided.
INTEGER (217)
INT atBindRuleBindParameter	1.3.6.1.4.1.800.2.2.10.16.1.8	INTEGER	read-write	The parameters to bind together.
INT atBindRuleGroupId	1.3.6.1.4.1.800.2.2.10.16.1.1	INTEGER	read-write	The group id of the vlan for which this rule is configured.
INT atBindRuleIndex	1.3.6.1.4.1.800.2.2.10.16.1.3	INTEGER	read-write	The index which uniquely identifies this rule for this vlan.
INT atBindRuleStatus	1.3.6.1.4.1.800.2.2.10.16.1.9	INTEGER	read-write	The admin status for this rule.
INT atBindRuleVlanId	1.3.6.1.4.1.800.2.2.10.16.1.2	INTEGER	read-write	The vlan id for which this rule is configured.
INT atDefaultVlan	1.3.6.1.4.1.800.2.2.10.8	INTEGER	read-write	When set to on, it allows devices to be assigned to the default vlan, else if it set to off, such devices are not assigned to any vlan, thereby preventing them from communicating to other devices.
INT atDHCPMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.19.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atDHCPMacRuleIndex	1.3.6.1.4.1.800.2.2.10.19.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
INT atDHCPMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.19.1.5	INTEGER	read-write	This object determines if the MAC address is included in the VLAN definition. If the object is set to disabled, the MAC address is removed from the VLAN definition.
INT atDHCPMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.19.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
INT atDHCPportRuleGroupId	1.3.6.1.4.1.800.2.2.10.18.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atDHCPportRuleIdx	1.3.6.1.4.1.800.2.2.10.18.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
INT atDHCPportRulePortState	1.3.6.1.4.1.800.2.2.10.18.1.5	INTEGER	read-write	This object determines whether the port is being added or deleted from this port rule definition.
INT atDHCPportRuleVLANId	1.3.6.1.4.1.800.2.2.10.18.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
INT atMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.2.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atMacRuleIndex	1.3.6.1.4.1.800.2.2.10.2.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
INT atMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.2.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
INT atMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.2.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
INT atMcastRuleGroupId	1.3.6.1.4.1.800.2.2.10.11.1.1	INTEGER	read-write	The group in which this rule is defined.
INT atMcastRuleIndex	1.3.6.1.4.1.800.2.2.10.11.1.3	INTEGER	read-write	The rule index ( a vlan can have multiple rules defined ) which exactly identifies this rule.
INT atMcastRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.11.1.5	INTEGER	read-write	The admin-state of this multicast mac address.
INT atMcastRuleVLANId	1.3.6.1.4.1.800.2.2.10.11.1.2	INTEGER	read-write	The VLAN for which this rule is defined.
INT atmcMacRuleGroupId	1.3.6.1.4.1.800.2.2.10.10.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atmcMacRuleIndex	1.3.6.1.4.1.800.2.2.10.10.1.3	INTEGER	read-write	The rule of which this MAC address list is part of. When creating a VLAN, this object must be set to 0.
INT atmcMacRuleMacAddressState	1.3.6.1.4.1.800.2.2.10.10.1.5	INTEGER	read-write	This object determines if the MAC address is included in the VLAN definition. If the object is set to disabled, the MAC address is removed from the VLAN definition.
INT atmcMacRuleVLANId	1.3.6.1.4.1.800.2.2.10.10.1.2	INTEGER	read-write	This object is the VLAN Id for this MAC-rule based vlan.
INT atmcportRuleGroupId	1.3.6.1.4.1.800.2.2.10.9.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atmcportRuleIdx	1.3.6.1.4.1.800.2.2.10.9.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
INT atmcportRulePortState	1.3.6.1.4.1.800.2.2.10.9.1.5	INTEGER	read-write	This object determines whether the port is being added or deleted from this port rule definition.
INT atmcportRuleVLANId	1.3.6.1.4.1.800.2.2.10.9.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
INT atmcVLANAdminStatus	1.3.6.1.4.1.800.2.2.10.13.1.4	INTEGER	read-write	The Admin status of the VLAN. If set to disabled, any rules configured for this vlan will no longer be used and their status will be changed to disabled.
INT atmcVLANGroupId	1.3.6.1.4.1.800.2.2.10.13.1.1	INTEGER	read-write	This is the VLAN group to which the VLAN belongs.
INT atmcVLANId	1.3.6.1.4.1.800.2.2.10.13.1.2	INTEGER	read-write	The VLAN id for this VLAN.
INT atmcVLANOperStatus	1.3.6.1.4.1.800.2.2.10.13.1.5	INTEGER	read-only	The operation status of this vlan. If there any devices learnt by this system on this vlan, the operation status of the vlan is said to be active.
INT atmcVLANRuleIndex	1.3.6.1.4.1.800.2.2.10.12.1.3	INTEGER	read-only	The exact rule identifier for this rule.
INT atmcVLANRuleSubIndex	1.3.6.1.4.1.800.2.2.10.12.1.4	INTEGER	read-only	In case a VLAN is defined using multiple instances of the same type of rule, this object identifies the exact instance of that type of rule. This object could then be used along with the group and vlanid to get the complete definition of this rule from the appropriate rule table.
INT atmcVLANRuleSumGroupId	1.3.6.1.4.1.800.2.2.10.12.1.1	INTEGER	read-only	The group to which the VLAN belongs.
INT atmcVLANRuleSumVLANId	1.3.6.1.4.1.800.2.2.10.12.1.2	INTEGER	read-only	The VLAN Id for this rule is defined.
INT atmcVLANRuleType	1.3.6.1.4.1.800.2.2.10.12.1.5	INTEGER	read-only	The type of rule. This object can then be used to decide which table to lookup for the complete definition of the rule.
INT atNetRuleGroupId	1.3.6.1.4.1.800.2.2.10.4.1.1	INTEGER	read-write	This object indicates the VLAN Group in which this VLAN is defined.
INT atNetRuleIndex	1.3.6.1.4.1.800.2.2.10.4.1.3	INTEGER	read-write	This object specifies the exact Network Address rule for this VLAN. When creating a VLAN using the Network Address rule, this object must be set to 0.
INT atNetRuleProtocolId	1.3.6.1.4.1.800.2.2.10.4.1.4	INTEGER	read-write	This object indicates which protocols Network Address is used to define this VLAN.
INT atNetRuleStatus	1.3.6.1.4.1.800.2.2.10.4.1.6	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
INT atNetRuleVLANId	1.3.6.1.4.1.800.2.2.10.4.1.2	INTEGER	read-write	This object is the VLAN Id for this NetAddr-rule based vlan.
INT atportRuleGroupId	1.3.6.1.4.1.800.2.2.10.1.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is.
INT atportRuleIdx	1.3.6.1.4.1.800.2.2.10.1.1.3	INTEGER	read-write	This object indicates the exact port-rule for this VLAN. There can be more than one port-rule defined for this VLAN. This object identifies the port rule of which the port is part of. When creating a VLAN using this table, this value should be set to 0 to indicate that this is a new port rule. If the port rule needs to be modified, then this object will be the port rule to modify.
INT atportRulePortState	1.3.6.1.4.1.800.2.2.10.1.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
INT atportRuleVLANId	1.3.6.1.4.1.800.2.2.10.1.1.2	INTEGER	read-write	This object is the VLAN defined by this port-rule.
INT atProtoRuleGroupId	1.3.6.1.4.1.800.2.2.10.3.1.1	INTEGER	read-write	This object indicates the VLAN Group in which the VLAN defined by this rule is defined.
INT atProtoRuleIndex	1.3.6.1.4.1.800.2.2.10.3.1.3	INTEGER	read-write	This object specifies the exact protocol rule for this VLAN. On creating a VLAN based on protocol rule, this object must be set to 0.
INT atProtoRuleStatus	1.3.6.1.4.1.800.2.2.10.3.1.5	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
INT atProtoRuleVLANId	1.3.6.1.4.1.800.2.2.10.3.1.2	INTEGER	read-write	This object is the VLAN Id defined by this Protocol-rule.
INT atUserRuleGroupId	1.3.6.1.4.1.800.2.2.10.5.1.1	INTEGER	read-write	This object indicates the VLAN Group in which this VLAN is defined.
INT atUserRuleIndex	1.3.6.1.4.1.800.2.2.10.5.1.3	INTEGER	read-write	This object indicates the exact User defined rule for this VLAN. When creating a VLAN using the user defined rules, this object must be set to 0.
INT atUserRuleOffset	1.3.6.1.4.1.800.2.2.10.5.1.4	INTEGER	read-write	This object defines the offset into a frame where the pattern to match is located. This offset is relative to the start of the MAC header.
INT atUserRuleStatus	1.3.6.1.4.1.800.2.2.10.5.1.7	INTEGER	read-write	This object indicates whether this perticular rule is being used as part this VLANs definition. When set to disabled, this rule is not used as part of this vlans definition.
INT atUserRuleVLANId	1.3.6.1.4.1.800.2.2.10.5.1.2	INTEGER	read-write	This object is the VLAN Id for this User-rule based vlan.
INT atvIPRouterFramingType	1.3.6.1.4.1.800.2.2.11.1.1.10	INTEGER	read-write	Provides the ability to set the outbound frame type for IP traffic. The default frame type is Ethernet 2. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
INT atvIPRouterRelayServicesFwd	1.3.6.1.4.1.800.2.2.11.1.1.12	INTEGER	read-write	Each of the 8 least significant bits are assigned to a UDP Relay service as follows: 01H - bootp (Not currently allowed) 02H - NBNS 04H - NBDD 08H - Gen1 10H - Gen2 20H - Gen3 40H - Gen4 80H - Gen5 A set bit indicates that packets are being forwarded to this vlan for the service corresponding to the bit. Use bit 15 to indicate that a UDP Relay Service should be unset and packets should not be forwarded to this vlan. 8001H - bootp (Not currently allowed) 8002H - NBNS 8004H - NBDD 8008H - Gen1 8010H - Gen2 8020H - Gen3 8040H - Gen4 8080H - Gen5
INT atvIPRouterRipConfigMode	1.3.6.1.4.1.800.2.2.11.1.1.11	INTEGER	read-write	RIP's operational mode. 'silent' means that RIP listens for routing updates but does not send them. 'deaf' means that RIP sends routing updates but not listen to them. 'active' means that RIP both sends and receives routing updates, and 'inactive' means that RIP is not operational on the given virtual LAN. The default is 'simple'.
INT atvIPRouterVLan	1.3.6.1.4.1.800.2.2.11.1.1.2	INTEGER	read-write	Auto Tracker VLAN Id for this router port instance.
INT atvIPRouterVLanGroup	1.3.6.1.4.1.800.2.2.11.1.1.1	INTEGER	read-write	VLAN Group ID for this atvIPRouterEntry instance.
INT atvIPXRouterFramingType	1.3.6.1.4.1.800.2.2.12.1.1.5	INTEGER	read-write	Provides the ability to set the outbound frame type for IPX traffic. The default frame type is 802.2 Novell Raw. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
INT atvIPXRouterProtocol	1.3.6.1.4.1.800.2.2.12.1.1.3	INTEGER	read-write	The routing protocol(s) for this virtual router port. Each IPX router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipxOther(1), ipxRip(2), ipxSap(4)
INT atvIPXRouterVLan	1.3.6.1.4.1.800.2.2.12.1.1.2	INTEGER	read-write	VLAN ID for this vIPXRouterEntry instance.
INT atvIPXRouterVLanGroup	1.3.6.1.4.1.800.2.2.12.1.1.1	INTEGER	read-write	VLAN Group ID for this vIPXRouterEntry instance.
INT atvIPXSrcRteType	1.3.6.1.4.1.800.2.2.12.1.1.9	INTEGER	read-write	Provide the ability to set the type of source routing broadcasts between AllRoutesExplorer(0) and SpanningTreeExplorer(1).
INT atVLANAdminStatus	1.3.6.1.4.1.800.2.2.10.7.1.4	INTEGER	read-write	The Admin status of the VLAN. If set to disabled, any rules configured for this vlan will no longer be used and their status will be changed to disabled.
INT atVLANGroupId	1.3.6.1.4.1.800.2.2.10.7.1.1	INTEGER	read-write	This is the VLAN group to which the VLAN belongs.
INT atVLANId	1.3.6.1.4.1.800.2.2.10.7.1.2	INTEGER	read-write	The VLAN id for this VLAN.
INT atVLANOperStatus	1.3.6.1.4.1.800.2.2.10.7.1.5	INTEGER	read-only	The operation status of this vlan. If there any devices learnt by this system on this vlan, the operation status of the vlan is said to be active.
INT atVLANRuleIndex	1.3.6.1.4.1.800.2.2.10.6.1.3	INTEGER	read-only	The exact rule identifier for this rule.
INT atVLANRuleSubIndex	1.3.6.1.4.1.800.2.2.10.6.1.4	INTEGER	read-only	In case a VLAN is defined using multiple instances of the same type of rule, this object identifies the exact instance of that type of rule. This object could then be used along with the group and vlanid to get the complete definition of this rule from the appropriate rule table.
INT atVLANRuleSumGroupId	1.3.6.1.4.1.800.2.2.10.6.1.1	INTEGER	read-only	The group to which the VLAN belongs.
INT atVLANRuleSumVLANId	1.3.6.1.4.1.800.2.2.10.6.1.2	INTEGER	read-only	The VLAN Id for this rule is defined.
INT atVLANRuleType	1.3.6.1.4.1.800.2.2.10.6.1.5	INTEGER	read-only	The type of rule. This object can then be used to decide which table to lookup for the complete definition of the rule.
INT gmAutoServiceActivePort	1.3.6.1.4.1.800.2.2.10.14.1.12	INTEGER	read-only	Physical Port on the which the service is currently active.
INT gmAutoServiceActiveSlot	1.3.6.1.4.1.800.2.2.10.14.1.11	INTEGER	read-only	Slot on the which the service is currently active.
INT gmAutoServiceAdminState	1.3.6.1.4.1.800.2.2.10.14.1.9	INTEGER	read-write	The admin state of this service
INT gmAutoServiceGroupId	1.3.6.1.4.1.800.2.2.10.14.1.1	INTEGER	read-write	Group for which this service is configured
INT gmAutoServiceIndex	1.3.6.1.4.1.800.2.2.10.14.1.4	INTEGER	read-write	Service index associated with this service
INT gmAutoServiceNumber	1.3.6.1.4.1.800.2.2.10.14.1.13	INTEGER	read-only	Service number assigned by the switch when this service is activated.
INT gmAutoServiceOperState	1.3.6.1.4.1.800.2.2.10.14.1.10	INTEGER	read-write	Operational state of this service.
INT gmAutoServicePrimaryPort	1.3.6.1.4.1.800.2.2.10.14.1.3	INTEGER	read-write	Primary port on which this service will be activated.
INT gmAutoServicePrimarySlot	1.3.6.1.4.1.800.2.2.10.14.1.2	INTEGER	read-write	Primary slot on which this service will be activated.
INT gmAutoServiceSecondaryPort	1.3.6.1.4.1.800.2.2.10.14.1.8	INTEGER	read-write	Secondary port on which this service will be activated.
INT gmAutoServiceSecondarySlot	1.3.6.1.4.1.800.2.2.10.14.1.7	INTEGER	read-write	Secondary slot on which this service will be activated.
INT gmAutoServiceTranslations	1.3.6.1.4.1.800.2.2.10.14.1.14	INTEGER	read-write	This parameter controls whether frame translations will be exercised for this lane service once activated.
INT gmAutoServiceType	1.3.6.1.4.1.800.2.2.10.14.1.5	INTEGER	read-write	Type of this service - currently only lane is supported and this object should have a value of 1.
INT gmDefGroup	1.3.6.1.4.1.800.2.2.10.22	INTEGER	read-write	When this object is set to on, the switch will assign the port's default group id to all such devices which are learned and do not match any policies for mobile groups. If it is set to off, such devices will get assigned to no groups and the traffic they send will be discarded by the switch.
INT gmGroupListGroupId	1.3.6.1.4.1.800.2.2.10.17.1.3	INTEGER	read-only	One of the Groups to which the port belongs.
INT gmGroupListPortInterface	1.3.6.1.4.1.800.2.2.10.17.1.2	INTEGER	read-only	The physical port number for which the group list is requested.
INT gmGroupListPortSlot	1.3.6.1.4.1.800.2.2.10.17.1.1	INTEGER	read-only	The slot id of the port for which the group list is requested.
INT gmMoveToDefGroup	1.3.6.1.4.1.800.2.2.10.21	INTEGER	read-write	When this object is set on, the switch will remove the port of out of a mobile group when the last device in that group learnt on that port ages out due to inactivity. When it is set to off, the port will remain in such a group, even if all macs leant on that port in that group age out.
INT groupMobilityStatus	1.3.6.1.4.1.800.2.2.10.20	INTEGER	read-write	This object can used to configure the global status of group-mobility feature on the switch.
INT pMapConfigId	1.3.6.1.4.1.800.2.2.17.3.1.1	INTEGER	read-only	A unique number that identifies this Port Mapping with the physical OmniSwitch or OSR.
INT pMapConfigStatus	1.3.6.1.4.1.800.2.2.17.3.1.2	INTEGER	read-write	This object indicates whether to set (1) or delete (2) the port mapping configeration..
INT pMapEgressAdminStatus	1.3.6.1.4.1.800.2.2.17.2.1.6	INTEGER	read-write	This object indicates whether to add(1) to or delete(2) from the Port Mapping Egress Port.
INT pMapEgressId	1.3.6.1.4.1.800.2.2.17.2.1.1	INTEGER	read-write	A unique number that identifies this Port Mapping on the physical OmniSwitch or OSR.
INT pMapEgressInst	1.3.6.1.4.1.800.2.2.17.2.1.5	INTEGER	read-write	A Instance that is associated with this Port Mapping Egress Port.
INT pMapEgressPort	1.3.6.1.4.1.800.2.2.17.2.1.3	INTEGER	read-write	A physical port number that is associated with the Port Mapping Egress Port.
INT pMapEgressSlot	1.3.6.1.4.1.800.2.2.17.2.1.2	INTEGER	read-write	A physical slot number on whitch the Port Mapping Egress Port is configured.
INT pMapEgressSrvc	1.3.6.1.4.1.800.2.2.17.2.1.4	INTEGER	read-write	A service type that is associated with this Port Mapping Egress Port.
INT pMapIngressAdminStatus	1.3.6.1.4.1.800.2.2.17.1.1.6	INTEGER	read-write	This object indicates whether to add(1) to or delete(2) from the Port Mapping Ingress List.
INT pMapIngressId	1.3.6.1.4.1.800.2.2.17.1.1.1	INTEGER	read-write	A unique number that identifies this Port Mapping on the OmniSwitch or OSR.
INT pMapIngressInst	1.3.6.1.4.1.800.2.2.17.1.1.5	INTEGER	read-write	A Instance that is associated with this Port Mapping Ingress Port.
INT pMapIngressPort	1.3.6.1.4.1.800.2.2.17.1.1.3	INTEGER	read-write	A physical port number that is associated with the Port Mapping Ingress Port.
INT pMapIngressSlot	1.3.6.1.4.1.800.2.2.17.1.1.2	INTEGER	read-write	A physical slot number on which the Port Mapping Ingress Port is configured.
INT pMapIngressSrvc	1.3.6.1.4.1.800.2.2.17.1.1.4	INTEGER	read-write	A service type that is associated with this Port Mapping Ingress Port.
INT qGroupAdminStatus	1.3.6.1.4.1.800.2.2.15.1.1.8	INTEGER	read-write	Value of 0 indicates the service should be deleted, value of 1 indicates the service should be created.
INT qGroupGroupId	1.3.6.1.4.1.800.2.2.15.1.1.3	INTEGER	read-write	Group Id on the particular port.
INT qGroupMode	1.3.6.1.4.1.800.2.2.15.1.1.4	INTEGER	read-write	gstsxylan(1) indicates spanning tree support on a gigabit port by proprietary mode and gstsieee(2) indicates spanning tree on a gigabit port by IEEE mode, msts(3) indicates multiple spanning tree support on a 10/100 Mammoth Ethernet port, and ssts(4) indicates single spanning tree support on a 10/100 Mammoth Ethernet port.
INT qGroupPort	1.3.6.1.4.1.800.2.2.15.1.1.2	INTEGER	read-write	The physical port number.
INT qGroupPriority	1.3.6.1.4.1.800.2.2.15.1.1.7	INTEGER	read-write	Priority used for support multiple spanning tree.
INT qGroupSlot	1.3.6.1.4.1.800.2.2.15.1.1.1	INTEGER	read-write	The slot id of the required port.
INT qGroupTag	1.3.6.1.4.1.800.2.2.15.1.1.6	INTEGER	read-write	Tag used for support multiple spanning tree.
INT v80210Command	1.3.6.1.4.1.800.2.2.13.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given 80210 service.
INT v80210LanNumber	1.3.6.1.4.1.800.2.2.13.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given 80210 service.
INT v80210ServicesBridgeID	1.3.6.1.4.1.800.2.2.13.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given 80210 service. A value of 0 means that the Virtual Bridge port does not exist.
INT v80210ServicesSlot	1.3.6.1.4.1.800.2.2.13.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the 80210 service.
INT v80210ServicesStation	1.3.6.1.4.1.800.2.2.13.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the 80210 service.
INT v80210Slot	1.3.6.1.4.1.800.2.2.13.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the 80210 service.
INT v80210Station	1.3.6.1.4.1.800.2.2.13.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the 80210 service.
INT vBrdgStaticPortFuncTypInst	1.3.6.1.4.1.800.2.2.4.4.1.5	INTEGER	read-write	The service type instance of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortIF and vBrdgStaticPortFuncTyp must also be set.
INT vBrdgStaticPortIF	1.3.6.1.4.1.800.2.2.4.4.1.3	INTEGER	read-write	The on-board interface of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortFuncTyp and vBrdgStaticPortFuncTypInst must also be set.
INT vBrdgStaticPortSlot	1.3.6.1.4.1.800.2.2.4.4.1.2	INTEGER	read-write	The slot number of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is provided, vBrdgStaticPortIF, vBrdgStaticPortFuncTyp and vBrdgStaticPortFuncTypInst must also be set.
INT vBrdgStaticStatus	1.3.6.1.4.1.800.2.2.4.4.1.6	INTEGER	read-write	This object indicates the status of this entry. Xylan does not support other(1). The default value is permenent(3). invalid(2) - writing this value to the object removes the entry. permanent(3) - this entry will never age out and remain even after next reset. deleteOnReset(4) - this entry will not age out until reset. deleteOnTimeout(5) - write this value to the entry will cause it to age out.
INT vBrdgTpAgingTime	1.3.6.1.4.1.800.2.2.4.2	INTEGER	read-write	The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
INT vBrdgTpATVLANAgeingTime	1.3.6.1.4.1.800.2.2.4.5	INTEGER	read-write	The AutoTracker extended ageing timer. This value indicates how long the switch will remember the mac address and its associated vlan information. The default value is 1200 secs. This means that the mac information will be remembered for (vBrdgTpATVLANAgeingTime - vBrdgTpAgingTime) seconds after the mac is aged out. This value must be set to a value greater than or equal to vBrdgTpAgingTime.
INT vBrdgTpFdbDupStatus	1.3.6.1.4.1.800.2.2.4.3.1.9	INTEGER	read-only	The variable indicates if vBrdgTpFdbAddress is a duplicate Mac.
INT vBrdgTpFdbGroupId	1.3.6.1.4.1.800.2.2.4.3.1.1	INTEGER	read-only	The GroupId for this bridge.
INT vBrdgTpFdbRcvPortFuncTypInst	1.3.6.1.4.1.800.2.2.4.3.1.6	INTEGER	read-only	The service type instance of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvPortIF	1.3.6.1.4.1.800.2.2.4.3.1.4	INTEGER	read-only	The on-board interface number of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvPortSlot	1.3.6.1.4.1.800.2.2.4.3.1.3	INTEGER	read-only	The slot number of the port that vBrdgTpFdbAddress is received.
INT vBrdgTpFdbRcvStatus	1.3.6.1.4.1.800.2.2.4.3.1.7	INTEGER	read-only	The status of this entry. Xylan does not support other(1) and self(4). The meanings of the values are: invalid(2) : this entry is no longer valid, but has not yet been flushed from the table. learned(3) : this entry has been learned. mgmt(5) : this entry is configured as a static entry.
INT vBrdgTpFdbRcvVLANMembership	1.3.6.1.4.1.800.2.2.4.3.1.8	INTEGER	read-only	The Auto-Tracker VLAN membership for this device. Each bit that is set in this objects 32 bit value indicates that the device is part of the VLAN given by that bits position.
INT vDBrCommand	1.3.6.1.4.1.800.2.2.14.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given DBr service.
INT vDBrLanNumber	1.3.6.1.4.1.800.2.2.14.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given DBr service.
INT vDBrServicesBridgeID	1.3.6.1.4.1.800.2.2.14.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given DBr service. A value of 0 means that the Virtual Bridge port does not exist.
INT vDBrServicesSlot	1.3.6.1.4.1.800.2.2.14.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the DBr service.
INT vDBrServicesStation	1.3.6.1.4.1.800.2.2.14.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the DBr service.
INT vDBrSlot	1.3.6.1.4.1.800.2.2.14.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the DBr service.
INT vDBrStation	1.3.6.1.4.1.800.2.2.14.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the DBr service.
INT vDupMacIntf	1.3.6.1.4.1.800.2.2.16.3	INTEGER	read-only	The interface number (1-based) where duplicate MAC address was last received.
INT vDupMacSlot	1.3.6.1.4.1.800.2.2.16.2	INTEGER	read-only	The slot number (1-based) where duplicate MAC address was last received.
INT vDupMacTime	1.3.6.1.4.1.800.2.2.16.4	INTEGER	read-only	The time in seconds that the duplicate MAC address was detected.
INT vIPRouterFramingType	1.3.6.1.4.1.800.2.2.2.1.1.9	INTEGER	read-write	Provides the ability to set the outbound frame type for IP traffic. The default frame type is Ethernet 2. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
INT vIPRouterRelayMode	1.3.6.1.4.1.800.2.2.2.2.1.2	INTEGER	read-write	This controls whether the internal UDP Relay service is enabled or disabled. When enabled, the service will forward packets to a specified server (or specified broadcast address.) or VLAN. Note that for BOOTP/DHCP service, unless the relay's next hop ip address (vIPRouterRelayForwAddr) is set to a valid value, it will not possible to enable the relay. For other services, a VLAN to forwared to (vIPRouterRelayForwVlan in vIPRouterRelayForwTable) or a next hop ip address must be set. The mode definitions are as follows: 1 - enabled 2 - configureRequest 3 - underConfiguration 4 - disabled A manager will set the state to configureRequest(2) before attempting to configure any other parameters for a particular UPD Service. The agent will then set the state to underConfiguration(3). When in the underConfiguration(3) state, a UDP service is not completely configured and will remain in this state until the management station is finished configuring and sets the state to either enabled(1) or disabled(4). A manager is restricted to changing the state of an entry in the following ways: config under To: valid Request config invalid From: valid OK NO OK OK configRequest N/A N/A N/A N/A underConfig OK NO OK OK invalid NO OK NO OK
INT vIPRouterRelayParam1	1.3.6.1.4.1.800.2.2.2.2.1.4	INTEGER	read-write	This sets the BOOTP/DHCP relay's maximum hops forwarding limit. If a BOOT/DHCP frame arrives with hopcount greater than or equal to vIPRouterRelayParam1, it will be dropped. For BOOTP/DHCP the legal range is 1..16. For Generic services, this sets the port number to be forwarded. The legal range is -1..65535 with -1 indicating the unset state.
INT vIPRouterRelayParam2	1.3.6.1.4.1.800.2.2.2.2.1.5	INTEGER	read-write	This sets the BOOTP/DHCP relay's forwarding delay and is only used by the BOOTP/DHCP service. For other services it is ignored. It is typically set as seconds, but the value is totally client dependent. The relay will not forward frames until client frames have 'secs' field set to at least the value of vIPRouterRelayParam2.
INT vIPRouterRipConfigMode	1.3.6.1.4.1.800.2.2.2.1.1.10	INTEGER	read-write	RIP's operational mode. 'silent' means that RIP listens for routing updates but does not send them. 'deaf' means that RIP sends routing updates but not listen to them. 'active' means that RIP both sends and receives routing updates, and 'inactive' means that RIP is not operational on the given virtual LAN. The default is 'simple'.
INT vIPRouterVLan	1.3.6.1.4.1.800.2.2.2.1.1.1	INTEGER	read-write	VLAN ID for this vIPRouterEntry instance.
INT vIPXRouterFramingType	1.3.6.1.4.1.800.2.2.3.1.1.4	INTEGER	read-write	Provides the ability to set the outbound frame type for IPX traffic. The default frame type is 802.2 Novell Raw. If the frame type is incompatible with the transmitting media, appropriate translation will be performed at egress.
INT vIPXRouterProtocol	1.3.6.1.4.1.800.2.2.3.1.1.2	INTEGER	read-write	The routing protocol(s) for this virtual router port. Each IPX router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipxNone(1), ipxRipOnly(2), ipxRipAndSap(3), ipxTriggered(4)
INT vIPXRouterVLan	1.3.6.1.4.1.800.2.2.3.1.1.1	INTEGER	read-write	VLAN ID for this vIPXRouterEntry instance.
INT vIPXSrcRteType	1.3.6.1.4.1.800.2.2.3.1.1.8	INTEGER	read-write	Provide the ability to set the type of source routing broadcasts between AllRoutesExplorer(0) and SpanningTreeExplorer(1).
INT vLanAuthGroup	1.3.6.1.4.1.800.2.2.1.2.1.11	INTEGER	read-write	If set to enable, makes this a authenticated group. If set to disable, makes this a non-authenticated group. For it to be set to enable, the group should be a mobile group.
INT vLanBrdgTpExtendedAgeingTime	1.3.6.1.4.1.800.2.2.1.2.1.14	INTEGER	read-write	The AutoTracker extended ageing timer. This value indicates how long the switch will remember the mac address and its associated vlan information. The default value is 1200 secs. This means that the mac information will be remembered for (vLanBrdgTpExtendedAgeingTime - vBrdgTpAgingTime) seconds after the mac is aged out. This value must be set to a value greater than or equal to vBrdgTpAgingTime.
INT vLanBridgeType	1.3.6.1.4.1.800.2.2.1.2.1.3	INTEGER	read-only	Indicates what type of bridging this VLAN can perform. If a VLAN is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
INT vLanCurrentNumber	1.3.6.1.4.1.800.2.2.1.1	INTEGER	read-write	The current instance of Virtual LAN which corresponds to vLanNumber in object type vLanEntry. All the Bridging, Spanning Tree, and interface parameters refered thereafter will be referenced from this instance only. Default value upon the OmniSwitch power up is 1. It must be set to the desired value before any access to the rest of the virtual LAN system.
INT vLanFloodOverride	1.3.6.1.4.1.800.2.2.1.2.1.8	INTEGER	read-write	Provides the flood limit value for all virtual ports that belong to the specied VLAN. The number is given in bytes per second. -1 and 0 have a special meaning. -1 means use the default or configured flood limit for each virtual port that belongs to the specified VLAN. 0 disables flood limiting on all virtual ports that belong to the specifed VLAN.
INT vLanMobileGroup	1.3.6.1.4.1.800.2.2.1.2.1.10	INTEGER	read-write	If set to enabled, makes this a mobile group. If set to disabled, makes this a non-mobile gropu.
INT vLanNextFreeNumber	1.3.6.1.4.1.800.2.2.1.3	INTEGER	read-only	This is the next unused VLAN number. Typically this will be used to create a new VLAN with the next highest number.
INT vLanNumber	1.3.6.1.4.1.800.2.2.1.2.1.1	INTEGER	read-write	The VLAN number identifying this instance. Valid range from 1 to 65535.
INT vLanPriority	1.3.6.1.4.1.800.2.2.1.2.1.15	INTEGER	read-write	This is the priority of the given VLAN. It can be any one level from 0 to 7 with 0 being the lowest and 7 being the highest
INT vLanStpStatus	1.3.6.1.4.1.800.2.2.1.2.1.13	INTEGER	read-write	Indicates status of spanning tree for the current VLAN.
INT vPmapNextId	1.3.6.1.4.1.800.2.2.17.4	INTEGER	read-only	The unique number that identifiers the next Port Mapping Table.
INT vRipInfovLanNumber	1.3.6.1.4.1.800.2.2.7.1.1.1	INTEGER	read-only	The VLAN number identifying this instance. Valid range from 1 to 65535.
INT vSrAREblock	1.3.6.1.4.1.800.2.2.8.1.1.24	INTEGER	read-write	Indicates whether this port would treat ARE frames exactly like STE frames which would be blocked if the Spanning Tree mode is blocking. 1 - this port would not block ARE. 2 - this port would block ARE.
INT vSrBridgeLfMode	1.3.6.1.4.1.800.2.2.8.1.1.22	INTEGER	read-only	Indicates whether the bridge operates using older 3 bit length negotiation fields or the newer 6 bit length field in its RIF.
INT vSrBridgeNum	1.3.6.1.4.1.800.2.2.8.1.1.7	INTEGER	read-write	A bridge number uniquely identifies a bridge when more than one bridge is used to span the same two segments. Current source routing protocols limit this value to the range: 0 through 15. A value of 65535 signifies that no bridge number is assigned to this bridge.
INT vSrFuncType	1.3.6.1.4.1.800.2.2.8.1.1.3	INTEGER	read-only	The service type of the port for which this entry contains Source Route management information.
INT vSrHopCount	1.3.6.1.4.1.800.2.2.8.1.1.5	INTEGER	read-write	The maximum number of routing descriptors allowed in an All Paths or Spanning Tree Explorer frames.
INT vSrHopCountIn	1.3.6.1.4.1.800.2.2.8.1.1.25	INTEGER	read-write	The maximum number of routing descriptors allowed in an inbound All Paths or Spanning Tree Explorer frames.
INT vSrInstance	1.3.6.1.4.1.800.2.2.8.1.1.4	INTEGER	read-only	The service type instance of the port for which this entry contains Source Route management information.
INT vSrInterface	1.3.6.1.4.1.800.2.2.8.1.1.2	INTEGER	read-only	The on-board interface number of the port for which this entry contains Source Route management information.
INT vSrLargestFrame	1.3.6.1.4.1.800.2.2.8.1.1.9	INTEGER	read-write	The maximum size of the INFO field (LLC and above) that this virtual port can send/receive. It does not include any MAC level (framing) octets. The value of this object is used by this bridge to determine whether a modification of the LargestFrame (LF, see [14]) field of the Routing Control field of the Routing Information Field is necessary. 64 valid values are defined by the IEEE 802.5M SRT Addendum: 516, 635, 754, 873, 993, 1112, 1231, 1350, 1470, 1542, 1615, 1688, 1761, 1833, 1906, 1979, 2052, 2345, 2638, 2932, 3225, 3518, 3812, 4105, 4399, 4865, 5331, 5798, 6264, 6730, 7197, 7663, 8130, 8539, 8949, 9358, 9768, 10178, 10587, 10997, 11407, 12199, 12992, 13785, 14578, 15370, 16163, 16956, 17749, 20730, 23711, 26693, 29674, 32655, 35637, 38618, 41600, 44591, 47583, 50575, 53567, 56559, 59551, and 65535. An illegal value will not be accepted by the bridge.
INT vSrLocalSegment	1.3.6.1.4.1.800.2.2.8.1.1.6	INTEGER	read-write	The segment number that uniquely identifies the segment to which this virtual port is connected. Current source routing protocols limit this value to the range: 0 through 4095. (The value 0 is used by some management applications for special test cases.) A value of 65535 signifies that no segment number is assigned to this virtual port.
INT vSrPortType	1.3.6.1.4.1.800.2.2.8.1.1.23	INTEGER	read-write	Indicates whether this port is a SRT or SR only SRT = 1 SR = 2
INT vSrSapDenyFilter1	1.3.6.1.4.1.800.2.2.8.1.1.26	INTEGER	read-write	Packets with this SAP value are to be discarded.
INT vSrSapDenyFilter2	1.3.6.1.4.1.800.2.2.8.1.1.27	INTEGER	read-write	Packets with this SAP value are to be discarded.
INT vSrSapFilterEnable	1.3.6.1.4.1.800.2.2.8.2	INTEGER	read-write	A scalar value to enable or disable the SAP filtering feature in this source route switch.
INT vSrSapPermitFilter1	1.3.6.1.4.1.800.2.2.8.1.1.28	INTEGER	read-write	Packets without this SAP value are to be discarded.
INT vSrSapPermitFilter2	1.3.6.1.4.1.800.2.2.8.1.1.29	INTEGER	read-write	Packets without this SAP value are to be discarded.
INT vSrSlot	1.3.6.1.4.1.800.2.2.8.1.1.1	INTEGER	read-only	The physical slot number of the port for which this entry contains Source Route management information.
INT vSrSTESpanMode	1.3.6.1.4.1.800.2.2.8.1.1.10	INTEGER	read-write	Determines how this virtual port behaves when presented with a Spanning Tree Explorer frame. The value 'disabled(2)' indicates that the virtual port will not accept or send Spanning Tree Explorer packets; any STE packets received will be silently discarded. The value 'forced(3)' indicates the virtual port will always accept and propagate Spanning Tree Explorer frames. This allows a manually configured Spanning Tree for this class of packet to be configured. Note that unlike transparent bridging, this is not catastrophic to the network if there are loops. The value 'auto-span(1)' can only be returned by a bridge that both implements the Spanning Tree Protocol and has use of the protocol enabled on this virtual port. The behavior of the virtual port for Spanning Tree Explorer frames is determined by the state of vStpPortState. If the virtual port is in the 'forwarding' state, the frame will be accepted or propagated. Otherwise, it will be silently discarded.
INT vSrVirtualRing	1.3.6.1.4.1.800.2.2.8.1.1.8	INTEGER	read-write	This is to indicate whether the ring that this virtual port is connected to is virtual or physical 1 = virtual 2 = physical.
INT vStpForwardDelay	1.3.6.1.4.1.800.2.2.5.15	INTEGER	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to vStpBridgeForwardDelay which is the value that this VLAN and all others would start using if/when this bridge were to become the root.]
INT vStpHoldTime	1.3.6.1.4.1.800.2.2.5.14	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this VLAN, in units of hundredths of a second.
INT vStpLanMode	1.3.6.1.4.1.800.2.2.5.20	INTEGER	read-write	Indicates which type of spanning tree (IEEE or IBM) is to be used for the current VLAN.
INT vStpPortDesignatedCost	1.3.6.1.4.1.800.2.2.5.19.1.10	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
INT vStpPortDesignatedPtFuncTypInst	1.3.6.1.4.1.800.2.2.5.19.1.16	INTEGER	read-only	The service type instance of the port on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtIF	1.3.6.1.4.1.800.2.2.5.19.1.14	INTEGER	read-only	The on-board interface number of the port on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtPrio	1.3.6.1.4.1.800.2.2.5.19.1.12	INTEGER	read-only	The priority portion of the port ID on the Designated Bridge for this port's segment.
INT vStpPortDesignatedPtSlot	1.3.6.1.4.1.800.2.2.5.19.1.13	INTEGER	read-only	The slot of the port on the Designated Bridge for this port's segment.
INT vStpPortEnable	1.3.6.1.4.1.800.2.2.5.19.1.7	INTEGER	read-write	The enabled/disabled status of the port.
INT vStpPortForwardTransitions	1.3.6.1.4.1.800.2.2.5.19.1.17	INTEGER	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT vStpPortFuncTyp	1.3.6.1.4.1.800.2.2.5.19.1.3	INTEGER	read-only	The service type of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortFuncTypInst	1.3.6.1.4.1.800.2.2.5.19.1.4	INTEGER	read-only	The service type instance of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortIF	1.3.6.1.4.1.800.2.2.5.19.1.2	INTEGER	read-only	The on-board interface number of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortPathCost	1.3.6.1.4.1.800.2.2.5.19.1.8	INTEGER	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT vStpPortPriority	1.3.6.1.4.1.800.2.2.5.19.1.5	INTEGER	read-write	The priority of this port which used originally as part of the port ID specified in 802.1D.
INT vStpPortSlot	1.3.6.1.4.1.800.2.2.5.19.1.1	INTEGER	read-only	The slot number of the port for which this entry contains Spanning Tree Protocol management information.
INT vStpPortState	1.3.6.1.4.1.800.2.2.5.19.1.6	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. For ports which are disabled (see vStpPortEnable), this object will have a value of disabled(1). Xylan does not support the broken(6) state as defined in RFC1493.
INT vStpPriority	1.3.6.1.4.1.800.2.2.5.2	INTEGER	read-write	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of vLanBridgeAddress.
INT vStpProtocolSpecification	1.3.6.1.4.1.800.2.2.5.1	INTEGER	read-only	The version of the Spanning Tree Protocol implemented for the Xylan products. The IEE 802.1d implementation is the only version supported. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
INT vStpRootCost	1.3.6.1.4.1.800.2.2.5.7	INTEGER	read-only	The cost of the path to the root as seen from this VLAN bridge.
INT vStpRootPortFuncTypInst	1.3.6.1.4.1.800.2.2.5.11	INTEGER	read-only	The service type instance of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vStpRootPortIF	1.3.6.1.4.1.800.2.2.5.9	INTEGER	read-only	The on-board interface of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vStpRootPortSlot	1.3.6.1.4.1.800.2.2.5.8	INTEGER	read-only	The slot number of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
INT vTrunkingCommand	1.3.6.1.4.1.800.2.2.9.2.1.4	INTEGER	read-write	The command to either add or remove the specified VLAN ID from the given trunking service.
INT vTrunkingLanNumber	1.3.6.1.4.1.800.2.2.9.2.1.3	INTEGER	read-only	The VLAN ID to be added to or removed from the given trunking service.
INT vTrunkingServicesBridgeID	1.3.6.1.4.1.800.2.2.9.1.1.4	INTEGER	read-only	The VLAN ID of the Virtual Bridge port for the given trunking service. A value of 0 means that the Virtual Bridge port does not exist.
INT vTrunkingServicesSlot	1.3.6.1.4.1.800.2.2.9.1.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the trunking service.
INT vTrunkingServicesStation	1.3.6.1.4.1.800.2.2.9.1.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the trunking service.
INT vTrunkingSlot	1.3.6.1.4.1.800.2.2.9.2.1.1	INTEGER	read-only	The slot number (1-based) of the physical port providing the trunking service.
INT vTrunkingStation	1.3.6.1.4.1.800.2.2.9.2.1.2	INTEGER	read-only	The station number (1-based) within the physical port providing the trunking service.
IpAddress (8)
IP atBindRuleIPAddress	1.3.6.1.4.1.800.2.2.10.16.1.5	IpAddress	read-write	The IP address for which this binding is configured.
IP atvIPRouterBcastAddress	1.3.6.1.4.1.800.2.2.11.1.1.6	IpAddress	read-write	The IP broadcast address for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP atvIPRouterNetAddress	1.3.6.1.4.1.800.2.2.11.1.1.4	IpAddress	read-write	The IP network address for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP atvIPRouterSubNetMask	1.3.6.1.4.1.800.2.2.11.1.1.5	IpAddress	read-write	The IP network subnet mask for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP vIPRouterBcastAddress	1.3.6.1.4.1.800.2.2.2.1.1.5	IpAddress	read-write	The IP broadcast address for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP vIPRouterNetAddress	1.3.6.1.4.1.800.2.2.2.1.1.3	IpAddress	read-write	The IP network address for this virtual bridge instance for the purpose of allowing access from the external network management system.
IP vIPRouterRelayNextHop	1.3.6.1.4.1.800.2.2.2.2.1.3	IpAddress	read-write	This sets the relay's forwarding address. It can either be set to a distinct IP address (e.g. the address of a server), to an IP broadcast address or a VLAN.
IP vIPRouterSubNetMask	1.3.6.1.4.1.800.2.2.2.1.1.4	IpAddress	read-write	The IP network subnet mask for this virtual bridge instance for the purpose of allowing access from the external network management system.
MacAddress (10)
MAC atBindRuleMacAddress	1.3.6.1.4.1.800.2.2.10.16.1.6	MacAddress	read-write	The mac address for which this binding is configured.
MAC atDHCPMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.19.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
MAC atMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.2.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
MAC atMcastRuleMacAddress	1.3.6.1.4.1.800.2.2.10.11.1.4	MacAddress	read-write	The Multicast MAC Address that makes up this rule.
MAC atmcMacRuleMacAddress	1.3.6.1.4.1.800.2.2.10.10.1.4	MacAddress	read-write	This object gives the value of the MAC address that is part of the MAC rule definition.
MAC vBrdgStaticAddress	1.3.6.1.4.1.800.2.2.4.4.1.1	MacAddress	read-write	The MAC address which the static status applies.
MAC vBrdgTpFdbAddress	1.3.6.1.4.1.800.2.2.4.3.1.2	MacAddress	read-only	A unicast MAC address for which the VLAN bridge has forwarding and/or filtering information.
MAC vDupMacMac	1.3.6.1.4.1.800.2.2.16.1	MacAddress	read-only	The router port's MAC address for which the last duplicate MAC address was detected .
MAC vLanBridgeAddress	1.3.6.1.4.1.800.2.2.1.2.1.2	MacAddress	read-only	The MAC address used by the instance of VLAN which specified in vLanCurrentNumber when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this VLAN. However it is only required to be unique. When concatenated with vStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
MAC vLanRouterAddress	1.3.6.1.4.1.800.2.2.1.2.1.9	MacAddress	read-write	The user-configured MAC address used by the the VLAN's router port (IP / IPX). If this value has not been configured, the value returned is zero and this VLAN's router port will use a factory provided default value. The address should be specified in canonical order.
NetNumber (1)
NET atvIPXRouterNetAddress	1.3.6.1.4.1.800.2.2.12.1.1.4	NetNumber	read-write	The IPX network address for this virtual bridge.
OCTET STRING (13)
OCT atBindRulePortId	1.3.6.1.4.1.800.2.2.10.16.1.4	OCTET STRING	read-write	The port ( slot/intf/srvc/inst) for which this binding is configured.
OCT atBindRuleProtocol	1.3.6.1.4.1.800.2.2.10.16.1.7	OCTET STRING	read-write	The protocol for which this binding is configured.
OCT atDHCPportRulePortId	1.3.6.1.4.1.800.2.2.10.18.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
OCT atmcportRulePortId	1.3.6.1.4.1.800.2.2.10.9.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
OCT atNetRuleNetAddr	1.3.6.1.4.1.800.2.2.10.4.1.5	OCTET STRING	read-write	This object gives the network address that defines this vlan. If the protocol is IP, this object contains the four bytes of IP address followed by four bytes of IP Subnet Mask. If the protocol is IPX, this object contains the four bytes of Network Number followed by one byte of encapsulation type used on that network. The values for the encapsulation types are: byte 5 = 1 - IPX 802.3 encapsulation byte 5 = 2 - IPX Ethernet2 encapsulation byte 5 = 3 - IPX LLC encapsulation byte 5 = 4 - IPX SNAP encapsulation If the protocol is DECNet, this object contains the one byte of DEC area.
OCT atportRulePortId	1.3.6.1.4.1.800.2.2.10.1.1.4	OCTET STRING	read-write	This object defines the Virtual port that is part of this PORT rule. The first octet gives the slot number on which the port resides, the second being the physical interface, third octet being the service and the fourth being the instance of the service.
OCT atProtoRule	1.3.6.1.4.1.800.2.2.10.3.1.4	OCTET STRING	read-write	This object is an octet string of length 5 bytes. This object specifies the protocol type that defines this vlan. The values for the different protocols are: IP - first byte = 1, IPX - first byte = 2, AppleTalk - first byte = 3, DECNet - first byte = 4, Note that, in case of IP, ARP is included as IP and need not be specified explicitly. Similarly when AppleTalk is chosen both DDP and AARP are included. If any other protocol is used, it can be defined either by using Ether-type - first byte = 5 specifying its ether-type, second and third byte = ether-type value in hex. DSAP and SSAP - first byte = 6 specifying that its SAP type second byte = DSAP, third byte = SSAP in hex. SNAP Type - first byte = 7 specifying its SNAP second through sixth byte = snap value in hex.
OCT atUserRuleMask	1.3.6.1.4.1.800.2.2.10.5.1.6	OCTET STRING	read-write	This object defines the mask for the pattern to match. The Mask can be upto 8 bytes long but has to be of the same length as the Value.
OCT atUserRuleValue	1.3.6.1.4.1.800.2.2.10.5.1.5	OCTET STRING	read-write	This object defines the value of the pattern to match in a frame. The maximum length of this value can be 8 octets and the associated mask should have the same length as this object.
OCT atvIPRouterProtocol	1.3.6.1.4.1.800.2.2.11.1.1.3	OCTET STRING	read-write	The routing protocol(s) for this virtual router port. Each IP router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipOther(1), ipRip(2), ipEgp(4), ipGgp(8), ipHello(16), ipIs-is(32), ipEs-is(64), ipCiscoIgrp(128), ipBbnSpfIgp(256), ipOigp(512)
OCT vIPRouterProtocol	1.3.6.1.4.1.800.2.2.2.1.1.2	OCTET STRING	read-write	The routing protocol(s) for this virtual router port. Each IP router port can carry one or more routing protocols. This will be represented by the logical ORing of each protocol number. Which are: ipOther(1), ipRip(2), ipEgp(4), ipGgp(8), ipHello(16), ipIs-is(32), ipEs-is(64), ipCiscoIgrp(128), ipBbnSpfIgp(256), ipOigp(512)
OCT vIPXRouterNetAddress	1.3.6.1.4.1.800.2.2.3.1.1.3	OCTET STRING	read-write	The IPX network address for this virtual bridge.
OCT vLanAuthGroupProtocol	1.3.6.1.4.1.800.2.2.1.2.1.12	OCTET STRING	read-write	If a NULL string is returned as the value, this object is not applicable to that group. The contents of the string can interpreted based on the first byte. if the first byte is 1, the protocol is IP ( for all encaps ). 2, the protocol is IPX 3, the protocol is DECNET 4, the protocol is APPLETALK 5, the protocol is specified as an Ether-Type value with the next two bytes indicating the ether-type value, for e.g banyan vines ether-type will be specified as 08 0B AD 6, the protocol is specified using dsap and ssap values with the next two bytes giving the dsap and ssap value respectively, for e.g for banyan vines llc encap, it would look like 09 BC BC. 7, the protocol is specified using snap header with the next 5 bytes indicating the snap header for that protocol. For e.g if banyan vines snap has to be specified, it would look like, 0A 00 00 00 80 C4. FF, for all protocols.
Timeout (5)
TIM vStpBridgeForwardDelay	1.3.6.1.4.1.800.2.2.5.18	Timeout	read-write	The value that all VLANs use for ForwardDelay when this VLAN is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of vStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM vStpBridgeHelloTime	1.3.6.1.4.1.800.2.2.5.17	Timeout	read-write	The value that all VLANs use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM vStpBridgeMaxAge	1.3.6.1.4.1.800.2.2.5.16	Timeout	read-write	The value that all bridges use for MaxAge when this VLAN is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of vStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM vStpHelloTime	1.3.6.1.4.1.800.2.2.5.13	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this VLAN on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this VLAN is currently using.
TIM vStpMaxAge	1.3.6.1.4.1.800.2.2.5.12	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TimeTicks (1)
TIK vStpTimeSinceTopologyChange	1.3.6.1.4.1.800.2.2.5.4	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the VLAN bridge entity.
VIPRouterRelayServType (1)
VIP vIPRouterRelayService	1.3.6.1.4.1.800.2.2.2.2.1.1	VIPRouterRelayServType	read-only	This specifies the UDP Relay Service to be forwarded.
XylanPortFuncCodes (4)
XYL vBrdgStaticPortFuncTyp	1.3.6.1.4.1.800.2.2.4.4.1.4	XylanPortFuncCodes	read-write	The service type of the port that vBrdgStaticAddress applies. Entering this entry allows the MAC address to set in this port. If this entry is set, vBrdgStaticPortSlot, vBrdgStaticPortIF and vBrdgStaticPortFuncTypInst must also be set.
XYL vBrdgTpFdbRcvPortFuncTyp	1.3.6.1.4.1.800.2.2.4.3.1.5	XylanPortFuncCodes	read-only	The service type of the port that vBrdgTpFdbAddress is received.
XYL vStpPortDesignatedPtFuncTyp	1.3.6.1.4.1.800.2.2.5.19.1.15	XylanPortFuncCodes	read-only	The service type of the port on the Designated Bridge for this port's segment.
XYL vStpRootPortFuncTyp	1.3.6.1.4.1.800.2.2.5.10	XylanPortFuncCodes	read-only	The service type of the port which offers the lowest cost path from this VLAN bridge to the root bridge.
XylanVlanAdminStatCodes (5)
XYL atvIPRouterAdmStatus	1.3.6.1.4.1.800.2.2.11.1.1.8	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enable(2) or disable(1) (or delete (3)) upon user's request.
XYL atvIPXRouterAdmStatus	1.3.6.1.4.1.800.2.2.12.1.1.7	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enabled(2) or disabled(1) upon user's request.
XYL vIPRouterAdmStatus	1.3.6.1.4.1.800.2.2.2.1.1.7	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enable(2) or disable(1) (or delete (3)) upon user's request.
XYL vIPXRouterAdmStatus	1.3.6.1.4.1.800.2.2.3.1.1.6	XylanVlanAdminStatCodes	read-write	The particular routing environment can be enabled(2) or disabled(1) upon user's request.
XYL vLanAdmStatus	1.3.6.1.4.1.800.2.2.1.2.1.5	XylanVlanAdminStatCodes	read-write	The administrative status which can be set by configuration. Disable(1) will disable ALL vports that are connected to this VLAN, enable(2) will enable ALL ports on this VLAN, delete(3) will dettach and delete the ports/routers AND remove the VLAN.
XylanVlanModes (1)
XYL vLanMode	1.3.6.1.4.1.800.2.2.1.2.1.7	XylanVlanModes	read-write	Provides special operating mode setup and status. Currently this object is used to specify weather the VLAN supports the standard or ATM CIP connections.
XylanVlanOperStatCodes (6)
XYL atvIPRouterOperStatus	1.3.6.1.4.1.800.2.2.11.1.1.9	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
XYL atvIPXRouterOperStatus	1.3.6.1.4.1.800.2.2.12.1.1.8	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
XYL vIPRouterOperStatus	1.3.6.1.4.1.800.2.2.2.1.1.8	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router envirnment.
XYL vIPXRouterOperStatus	1.3.6.1.4.1.800.2.2.3.1.1.7	XylanVlanOperStatCodes	read-only	Provide operating status of a particular router environment.
XYL vLanOperStatus	1.3.6.1.4.1.800.2.2.1.2.1.6	XylanVlanOperStatCodes	read-only	Provide operating status of a particular VLAN environment.
XYL vStpStatus	1.3.6.1.4.1.800.2.2.5.21	XylanVlanOperStatCodes	read-write	Indicates status of spanning tree for the current VLAN.
No type (92)
atBindRuleEntry	1.3.6.1.4.1.800.2.2.10.16.1		not-accessible	An entry in the Binding Rule Table.
atBindRuleTable	1.3.6.1.4.1.800.2.2.10.16		not-accessible	The Binding Rule table.
atDHCPMacRuleEntry	1.3.6.1.4.1.800.2.2.10.19.1		not-accessible	An entry in the atDHCPMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
atDHCPMacRuleTable	1.3.6.1.4.1.800.2.2.10.19		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atDHCPportRuleEntry	1.3.6.1.4.1.800.2.2.10.18.1		not-accessible	An entry in the atDHCPportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
atDHCPportRuleTable	1.3.6.1.4.1.800.2.2.10.18		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
atMacRuleEntry	1.3.6.1.4.1.800.2.2.10.2.1		not-accessible	An entry in the atMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
atMacRuleTable	1.3.6.1.4.1.800.2.2.10.2		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atMcastRuleEntry	1.3.6.1.4.1.800.2.2.10.11.1		not-accessible	An entry in the MCAST Rule table.
atMcastRuleTable	1.3.6.1.4.1.800.2.2.10.11		not-accessible	This table is used to configure MCAST Rules for a VLAN.
atmcMacRuleEntry	1.3.6.1.4.1.800.2.2.10.10.1		not-accessible	An entry in the atmcMacRuleTable. Each entry in this table identifies exactly one MAC address. All entries in this table with the same GroupId and VLANId collectively define a VLAN.
atmcMacRuleTable	1.3.6.1.4.1.800.2.2.10.10		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a MAC Rule. Note the a VLAN created by using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atmcportRuleEntry	1.3.6.1.4.1.800.2.2.10.9.1		not-accessible	An entry in the atportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
atmcportRuleTable	1.3.6.1.4.1.800.2.2.10.9		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
atmcVLANControlEntry	1.3.6.1.4.1.800.2.2.10.13.1		not-accessible	An entry in the control table.
atmcVLANControlTable	1.3.6.1.4.1.800.2.2.10.13		not-accessible	This table gives the control information about all Auto-Tracker VLANs.
atmcVLANRuleSumEntry	1.3.6.1.4.1.800.2.2.10.12.1		not-accessible	An entry in the vlan summary table.
atmcVLANRuleSumTable	1.3.6.1.4.1.800.2.2.10.12		not-accessible	This table provides the summary of vlan rule configuration.
atNetRuleEntry	1.3.6.1.4.1.800.2.2.10.4.1		not-accessible	An entry in the atNetRuleTable. A VLAN can be defined using exaclty one address only except in the case of IPX where it could either be a Network number or the encapsulation.
atNetRuleTable	1.3.6.1.4.1.800.2.2.10.4		not-accessible	This table is used to configure an Auto-Tracker VLAN based on Net Addr Rule. Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atportRuleEntry	1.3.6.1.4.1.800.2.2.10.1.1		not-accessible	An entry in the atportRuleTable. Each entry in this table identifies exactly one port that is part of the VLAN definition. Hence all the entries of this table with the same GroupId and VLANId collectively define one VLAN which is based on a Port Rule. A specific port can be included in definition of more than one vlan as long as those two vlans are part of the same VLAN group. That is to say, a port can belong to more than one vlan but can be part of atmost one VLAN group.
atportRuleTable	1.3.6.1.4.1.800.2.2.10.1		not-accessible	This table is used to configure a Port Rule for a VLAN. The VLAN has to be created before any rule can be configured for it.
atProtoRuleEntry	1.3.6.1.4.1.800.2.2.10.3.1		not-accessible	An entry in the atProtoRuleTable.
atProtoRuleTable	1.3.6.1.4.1.800.2.2.10.3		not-accessible	This table is used to configure an Auto-Tracker VLAN based on Protocol Rule. Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atUserRuleEntry	1.3.6.1.4.1.800.2.2.10.5.1		not-accessible	An entry in the atUserRuleTable. A VLAN can be defined by more than one rule. In that case, the device will belong to that VLAN if it matches atleast one of the rules defined for that VLAN.
atUserRuleTable	1.3.6.1.4.1.800.2.2.10.5		not-accessible	This table is used to configure an Auto-Tracker VLAN based on a User Defined Rule.Note that any VLAN created using this table will not be enabled until the atVLANAdminStatus in the atVLANControlTable is not set to enabled.
atvIPRouterEntry	1.3.6.1.4.1.800.2.2.11.1.1		not-accessible	A VLAN entry.
atvIPRouterInfo	1.3.6.1.4.1.800.2.2.11
atvIPRouterTable	1.3.6.1.4.1.800.2.2.11.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
atvIPXRouterEntry	1.3.6.1.4.1.800.2.2.12.1.1		not-accessible	A VLAN entry.
atvIPXRouterInfo	1.3.6.1.4.1.800.2.2.12
atvIPXRouterTable	1.3.6.1.4.1.800.2.2.12.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
atVLANControlEntry	1.3.6.1.4.1.800.2.2.10.7.1		not-accessible	An entry in the control table.
atVLANControlTable	1.3.6.1.4.1.800.2.2.10.7		not-accessible	This table gives the control information about all Auto-Tracker VLANs.
atVLANRuleSumEntry	1.3.6.1.4.1.800.2.2.10.6.1		not-accessible	An entry in the vlan summary table.
atVLANRuleSumTable	1.3.6.1.4.1.800.2.2.10.6		not-accessible	This table provides the summary of vlan rule configuration.
gmAutoServiceEntry	1.3.6.1.4.1.800.2.2.10.14.1		not-accessible	an entry in the table
gmAutoServiceTable	1.3.6.1.4.1.800.2.2.10.14		not-accessible	Table of Auto-Activated Services
gmGroupListEntry	1.3.6.1.4.1.800.2.2.10.17.1		not-accessible	An entry in the Group List table.
gmGroupListTable	1.3.6.1.4.1.800.2.2.10.17		not-accessible	This table lists the groups on a port.
qGroupEntry	1.3.6.1.4.1.800.2.2.15.1.1		not-accessible	An entry in 802.1q group table.
qGroupTable	1.3.6.1.4.1.800.2.2.15.1		not-accessible	This table lists the 802.1q groups on a port.
v80210	1.3.6.1.4.1.800.2.2.13
v80210ServicesEntry	1.3.6.1.4.1.800.2.2.13.1.1		not-accessible	A 80210 services entry.
v80210ServicesTable	1.3.6.1.4.1.800.2.2.13.1		not-accessible	A list of commands to add or remove Virtual LANs from a 80210 service.
v80210VlanEntry	1.3.6.1.4.1.800.2.2.13.2.1		not-accessible	A 80210trunking Virtual LAN entry.
v80210VlanTable	1.3.6.1.4.1.800.2.2.13.2		not-accessible	A list of commands to add or remove Virtual LANs from a 80210 service.
v8021Q	1.3.6.1.4.1.800.2.2.15
vAutoTracker	1.3.6.1.4.1.800.2.2.10
vBrdgInfo	1.3.6.1.4.1.800.2.2.4
vBrdgStaticEntry	1.3.6.1.4.1.800.2.2.4.4.1		not-accessible	Information about a specific unicast MAC address for which the VLAN bridge has VLAN information.
vBrdgStaticTable	1.3.6.1.4.1.800.2.2.4.4		not-accessible	A table contains source addresses which can be configured to stay permanent (not aging out) in the Forwarding table.
vBrdgTpFdbEntry	1.3.6.1.4.1.800.2.2.4.3.1		not-accessible	Information about a specific unicast MAC address for which the VLAN bridge has some forwarding and/or filtering information.
vBrdgTpFdbTable	1.3.6.1.4.1.800.2.2.4.3		not-accessible	A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function within its VLAN in determining how to propagate a received frame.
vDBr	1.3.6.1.4.1.800.2.2.14
vDBrServicesEntry	1.3.6.1.4.1.800.2.2.14.1.1		not-accessible	An DBr services entry.
vDBrServicesTable	1.3.6.1.4.1.800.2.2.14.1		not-accessible	A list of commands to add or remove Virtual LANs from an DBr service.
vDBrVlanEntry	1.3.6.1.4.1.800.2.2.14.2.1		not-accessible	An DBr trunking Virtual LAN entry.
vDBrVlanTable	1.3.6.1.4.1.800.2.2.14.2		not-accessible	A list of commands to add or remove Virtual LANs from the DBr service.
vDupMac	1.3.6.1.4.1.800.2.2.16
vIPRouterEntry	1.3.6.1.4.1.800.2.2.2.1.1		not-accessible	A VLAN entry.
vIPRouterInfo	1.3.6.1.4.1.800.2.2.2
vIPRouterRelayEntry	1.3.6.1.4.1.800.2.2.2.2.1		not-accessible	A UDP Relay Service entry.
vIPRouterRelayTable	1.3.6.1.4.1.800.2.2.2.2		not-accessible	A list of UDP Relay Service instances.
vIPRouterTable	1.3.6.1.4.1.800.2.2.2.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
vIPXRouterEntry	1.3.6.1.4.1.800.2.2.3.1.1		not-accessible	A VLAN entry.
vIPXRouterInfo	1.3.6.1.4.1.800.2.2.3
vIPXRouterTable	1.3.6.1.4.1.800.2.2.3.1		not-accessible	A list of Virtual Router instances in this physical OmniSwitch.
vLanEntry	1.3.6.1.4.1.800.2.2.1.2.1		not-accessible	A VLAN entry.
vLanInfo	1.3.6.1.4.1.800.2.2.1
vLanTable	1.3.6.1.4.1.800.2.2.1.2		not-accessible	A list of Virtual LAN instances in this physical OmniSwitch.
vPmap	1.3.6.1.4.1.800.2.2.17
vPmapConfigEntry	1.3.6.1.4.1.800.2.2.17.3.1		not-accessible	A Port Mapping configuration table entry.
vPmapConfigTable	1.3.6.1.4.1.800.2.2.17.3		not-accessible	A list of Port Mapping config table instance on this physical OmniSwitch or OSR.
vPmapEgressEntry	1.3.6.1.4.1.800.2.2.17.2.1		not-accessible	A Port Mapping Egress Port entry.
vPmapEgressTable	1.3.6.1.4.1.800.2.2.17.2		not-accessible	A list of Port Mapping Egress port table instance on this physical OmniSwitch or OSR.
vPmapIngressEntry	1.3.6.1.4.1.800.2.2.17.1.1		not-accessible	A Port Mapping Ingress Port entry.
vPmapIngressTable	1.3.6.1.4.1.800.2.2.17.1		not-accessible	A list of Port Mapping Ingress port table instance on this physical OmniSwitch or OSR.
vRipInfo	1.3.6.1.4.1.800.2.2.7
vRipInfoEntry	1.3.6.1.4.1.800.2.2.7.1.1		not-accessible	A VLAN entry for RIP statistics.
vRipInfoTable	1.3.6.1.4.1.800.2.2.7.1		not-accessible	A list of Virtual LAN instances for RIP statistics.
vSr	1.3.6.1.4.1.800.2.2.8
vSrPortEntry	1.3.6.1.4.1.800.2.2.8.1.1		not-accessible	A list of information for each virtual port of a source route switch.
vSrTable	1.3.6.1.4.1.800.2.2.8.1		not-accessible	A table that contains information about every virtual port that is associated with this source route switch.
vStpInfo	1.3.6.1.4.1.800.2.2.5
vStpPortEntry	1.3.6.1.4.1.800.2.2.5.19.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
vStpPortTable	1.3.6.1.4.1.800.2.2.5.19		not-accessible	A table that contains port-specific information for the Spanning Tree Protocol.
vTrunking	1.3.6.1.4.1.800.2.2.9
vTrunkingServicesEntry	1.3.6.1.4.1.800.2.2.9.1.1		not-accessible	A trunking services entry.
vTrunkingServicesTable	1.3.6.1.4.1.800.2.2.9.1		not-accessible	A list of commands to add or remove Virtual LANs from a trunking service.
vTrunkingVlanEntry	1.3.6.1.4.1.800.2.2.9.2.1		not-accessible	A trunking Virtual LAN entry.
vTrunkingVlanTable	1.3.6.1.4.1.800.2.2.9.2		not-accessible	A list of commands to add or remove Virtual LANs from a trunking service.

FAQ

What is XYLAN-VLAN-MIB used for in a Xylan/Alcatel OmniSwitch monitoring setup?
It's a vendor-specific MIB for managing VLAN creation/deletion, port-to-VLAN membership, 802.1Q tagging configuration, and inter-VLAN routing policy on Xylan (later Alcatel) OmniSwitch devices. Administrators use it to confirm that a port's VLAN assignment or tagging mode matches the intended policy, and that inter-VLAN routing is enabled as expected, which helps catch misconfiguration-driven outages rather than physical hardware faults.

Why would I look up a specific OID in XYLAN-VLAN-MIB directly?
Administrators managing VLAN segmentation centrally often look up a specific XYLAN-VLAN-MIB OID directly to confirm which node governs a given VLAN or port-tagging setting on an OmniSwitch, since the module's object names are Xylan-specific even though it builds on standard bridge VLAN concepts.

RFC description

Xylan (now Alcatel) VLAN management MIB (vendor-private) for configuring and monitoring VLAN parameters.

Start monitoring Xylan/Alcatel OmniSwitch campus/enterprise LAN switch (VLAN creation, port-membership, 802.1Q tagging config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download XYLAN-VLAN-MIB

This MIB depends on

Related MIBs

What Is XYLAN-VLAN-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

FAQ

RFC description