All MIBs › X25-OPT-MIB › cdx6500X25CfgConnType
cdx6500X25CfgConnType
Module: X25-OPT-MIB
OID (symbolic): X25-OPT-MIB::cdx6500X25CfgConnType
OID (numeric): 1.3.6.1.4.1.449.2.1.2.1.1.2.1.2
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: Specify the control signal handshake and clocking required for a connection to be made to this port: simp - simple, no control signals required. dtr - dedicated, require the data terminal ready signal (DTR). dtrd - same as DTR, except data set ready (DSR) drops between calls. dimo - port handshakes with attached dial modem dimoa - same as DIMO except DSR never raised on incoming call from modem. dimob - same as DIMO except DSR follows DTR on incoming call from modem. dimov - port handshakes with attached V.25 bis dial modem. emri - port emulates a dial modem with ring indicator (RI). emdc - port emulates a dial modem with data carrier detect (DCD). simpv - SIMP/DIMOv, modem will switch from Leased to Dial-only mode when leased line goes down (used with Link Backup only). simpb - simple, no control signals required for data transmission and reception. By default output leads will be low.
What is cdx6500X25CfgConnType?
Selects the control-signal handshake and clocking behavior required for a device to connect to this X.25 port (e.g. simp for no handshake, dtr/dtrd for DTR-based handshaking, dimo variants for dial-modem handshaking); an admin picks the value matching the attached DTE/DCE hardware.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.449.2.1.2.1.1.2.1.2 snmpwalk -v2c -c public <target> X25-OPT-MIB::cdx6500X25CfgConnType
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.449.2.1.2.1.1.2.1.2.1 snmpget -v2c -c public <target> X25-OPT-MIB::cdx6500X25CfgConnType.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.449.2.1.2.1.1.2.1.2.1 i <value>
Start monitoring X.25 packet-switched network access devices/routers, e.g. cdx6500 platform (port-to-protocol-group config status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the X25-OPT-MIB::cdx6500X25CfgConnType OID value, configure state conditions and alerts, and monitor any X.25 packet-switched network access devices/routers, e.g. cdx6500 platform (port-to-protocol-group config status) from a single console.
OID Breakdown
Upper-level ancestors (12 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.449 | codex | ALC-OPT-MIB |
| 1.3.6.1.4.1.449.2 | cdxProductSpecific | ALC-OPT-MIB |
| 1.3.6.1.4.1.449.2.1 | cdx6500 | ALC-OPT-MIB |
| 1.3.6.1.4.1.449.2.1.2 | cdx6500Configuration | ALC-OPT-MIB |
| 1.3.6.1.4.1.449.2.1.2.1 | cdx6500CfgProtocolGroup | ALC-OPT-MIB |
| 1.3.6.1.4.1.449.2.1.2.1.1 | cdx6500PCTPortProtocolGroup | ALC-OPT-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.449.2.1.2.1.1.2 | cdx6500PPCTX25PortTable | X25-OPT-MIB |
| 1.3.6.1.4.1.449.2.1.2.1.1.2.1 | cdx6500PPCTX25PortEntry | X25-OPT-MIB |
| 1.3.6.1.4.1.449.2.1.2.1.1.2.1.2 | cdx6500X25CfgConnType | X25-OPT-MIB |