TPLINK-SNMPRMON-MIB

All MIBs › TPLINK-SNMPRMON-MIB

Category: Network Monitoring and Statistics, SNMP Management

Description: Manages TP-Link switch SNMP RMON statistics groups, history collection, and alarm thresholds.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TPLINK-SNMPRMON-MIB?

TPLINK-SNMPRMON-MIB is a TP-Link vendor MIB implementing a subset of RMON (Remote Monitoring) functionality on TP-Link managed switches, covering the Statistics, History, Event, and Alarm control groups. tpSnmpRmonStatsCtrlTable configures which Ethernet source port each statistics collector monitors; tpSnmpRmonHistoryCtrlTable/tpSnmpRmonHistoryDataTable periodically sample and store historical interface counters (drop events, octets, packets, broadcast/multicast packets, CRC/alignment errors, undersize/oversize packets, fragments, jabbers, collisions, and utilization percentage) at a configurable interval; tpSnmpRmonEventCtrlTable/tpSnmpRmonEventLogTable define named events (log-only, SNMP trap, or both) and record a log of triggered events; and tpSnmpRmonAlarmCtrlTable ties a sampled variable (drop/receive/broadcast/error/size-bucket counters) to rising/falling thresholds that trigger a specified event. Together these let an operator track interface-level traffic quality trends over time and get proactively alerted when a counter crosses a threshold, rather than only polling instantaneous values. It has no external MIB dependency beyond TPLINK-SNMP-MIB's root OID, and is deployed on TP-Link managed switches; administrators can perform a TPLINK-SNMPRMON-MIB download to load it into their MIB browser or NMS.

IPNetwork Monitor allows you to monitor SNMP objects defined in TPLINK-SNMPRMON-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

TP-Link managed switches

Monitoring Examples

An operator configures a tpSnmpRmonAlarmCtrlTable entry watching crcAlignErr on a port with a tpSnmpRmonAlarmCtrlRisingThreshold, tied to a tpSnmpRmonEventCtrlTable entry of type snmptrap; a burst of tpSnmpRmonHistoryDataCRCAlignErrors crossing that threshold would fire the trap and log the event, flagging a degrading cable or duplex mismatch on that port.

What Can Be Monitored

RMON statistics collector source-port configuration
periodic history samples (octets, packets, errors, utilization)
CRC/alignment/undersize/oversize/fragment/jabber/collision counters
configured RMON events and event log
rising/falling alarm thresholds on monitored variables

Imported Objects

From SNMPv2-SMI

Counter32
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

TEXTUAL-CONVENTION

From TPLINK-SNMP-MIB

tplinkSnmpMIBObjects

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using tpSnmpRmonHistoryDataDropEvents OID:

Select a TP-Link managed switch (RMON stats/history/alarm-threshold status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tpSnmpRmonHistoryDataDropEvents into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of events in which packets were dropped by the probe due to lack of resources during this sampling interval. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
tpSnmpRmonControl	1.3.6.1.4.1.11863.6.32.1.2
tpSnmpRmonStatisticsCtrl	1.3.6.1.4.1.11863.6.32.1.2.1
tpSnmpRmonStatsCtrlTable	1.3.6.1.4.1.11863.6.32.1.2.1.1		not-accessible	A list of SNMP RMON STATISTICS control entries.
tpSnmpRmonStatsCtrlEntry	1.3.6.1.4.1.11863.6.32.1.2.1.1.1		not-accessible	RMON (Remote Monitoring), basing on SNMP (Simple Network Management Protocol) architecture, functions to monitor the network. Statistics Group, as one of the commonly used RMON Groups, is used to collect the statistics of interfaces.
INT tpSnmpRmonStatsCtrlIndex	1.3.6.1.4.1.11863.6.32.1.2.1.1.1.1	INTEGER	read-only	The index of this entry.
OCT tpSnmpRmonStatsCtrlDataSource	1.3.6.1.4.1.11863.6.32.1.2.1.1.1.2	OCTET STRING	read-create	This object identifies the source of the data that this statistics entry is configured to analyze. This source can be any ethernet interface on this device. The source should be given as 1/0/1.
OCT tpSnmpRmonStatsCtrlOwner	1.3.6.1.4.1.11863.6.32.1.2.1.1.1.3	OCTET STRING	read-create	The owner of this entry.
ENT tpSnmpRmonStatsCtrlRowStatus	1.3.6.1.4.1.11863.6.32.1.2.1.1.1.4	EntryStatus	read-create	The status column has four defined values: - 'valid(1)', which indicates that the conceptual row is available for using by the managed device; - 'createRequest(2)', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to valid(1), making it available for using by the managed device; - 'underCreation(3)', which indicates that the conceptual row is existing in the managed device but not working. - 'invalid(4)', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row.
tpSnmpRmonHistoryCtrl	1.3.6.1.4.1.11863.6.32.1.2.2
tpSnmpRmonHistoryCtrlTable	1.3.6.1.4.1.11863.6.32.1.2.2.1		not-accessible	A list of SNMP RMON hisotry control entries.
tpSnmpRmonHistoryCtrlEntry	1.3.6.1.4.1.11863.6.32.1.2.2.1.1		not-accessible	History Group is one of the commonly used RMON (Remote Monitoring) Groups. After a history group is configured, the switch collects network statistics information periodically, based on which the management station can monitor network effectively.
INT tpSnmpRmonHistoryCtrlIndex	1.3.6.1.4.1.11863.6.32.1.2.2.1.1.1	INTEGER	read-only	The index of this entry.
OCT tpSnmpRmonHistoryCtrlSourcePort	1.3.6.1.4.1.11863.6.32.1.2.2.1.1.2	OCTET STRING	read-write	The port from which the history samples were taken. Specify the port in form of 1/0/1.
INT tpSnmpRmonHistoryCtrlInterval	1.3.6.1.4.1.11863.6.32.1.2.2.1.1.3	INTEGER	read-write	The interval to take samplings from the port. 10sec-3600sec.
INT tpSnmpRmonHistoryCtrlBucketsRequested	1.3.6.1.4.1.11863.6.32.1.2.2.1.1.4	INTEGER	read-write	The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry.
OCT tpSnmpRmonHistoryCtrlOwner	1.3.6.1.4.1.11863.6.32.1.2.2.1.1.5	OCTET STRING	read-write	The name of the device or user that defined the entry.
INT tpSnmpRmonHistoryCtrlStatus	1.3.6.1.4.1.11863.6.32.1.2.2.1.1.6	INTEGER	read-write	Enable/Disable the corresponding sampling entry. disable(0), disable the history entry. enable(1), enable the history entry.
tpSnmpRmonHistoryDataTable	1.3.6.1.4.1.11863.6.32.1.2.2.2		not-accessible	A list of SNMP RMON hisotry data entries.
tpSnmpRmonHistoryDataEntry	1.3.6.1.4.1.11863.6.32.1.2.2.2.1		not-accessible	Contains of the history data for a control entry
INT tpSnmpRmonHistoryDataIndex	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.1	INTEGER	read-only	index
INT tpSnmpRmonHistoryDataSampleIndex	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.2	INTEGER	read-only	An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
TIK tpSnmpRmonHistoryDataIntervalStart	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.3	TimeTicks	read-only	The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of the time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collecting the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
C32 tpSnmpRmonHistoryDataDropEventsEx	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.4	Counter32	read-only	The total number of events in which packets were dropped by the probe due to lack of resources during this sampling interval. Note that this number is not necessarily the number of packets dropped, it is just the number of times this condition has been detected.
C32 tpSnmpRmonHistoryDataOctets	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.5	Counter32	read-only	The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets)
C32 tpSnmpRmonHistoryDataPkts	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.6	Counter32	read-only	The number of packets (including bad packets) received during this sampling interval.
C32 tpSnmpRmonHistoryDataBroadcastPkts	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.7	Counter32	read-only	The number of good packets received during this sampling interval that were directed to the broadcast address.
C32 tpSnmpRmonHistoryDataMulticastPkts	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.8	Counter32	read-only	The number of good packets received during this sampling interval that were directed to the broadcast address.
C32 tpSnmpRmonHistoryDataCRCAlignErrors	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.9	Counter32	read-only	The number of packets received during this sampling interval that had a length (excluding framing bits but including FCS octets) between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C32 tpSnmpRmonHistoryDataUndersizePkts	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.10	Counter32	read-only	The number of packets received during this sampling interval that were less than 64 octets long (excluding framing bits but including FCS octets) and were otherwise well formed.
C32 tpSnmpRmonHistoryDataOversizePkts	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.11	Counter32	read-only	The number of packets received during this sampling interval that were longer than 1518 octets (excluding framing bits but including FCS octets) but were otherwise well formed.
C32 tpSnmpRmonHistoryDataFragments	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.12	Counter32	read-only	The total number of packets received during this sampling interval that were less than 64 octets in length (excluding framing bits but including FCS octets) had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C32 tpSnmpRmonHistoryDataJabbers	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.13	Counter32	read-only	The number of packets received during this sampling interval that were longer than 1518 octets (excluding framing bits but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C32 tpSnmpRmonHistoryDataCollisions	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.14	Counter32	read-only	The number of collion received during this sampling interval that
INT tpSnmpRmonHistoryDataUtilization	1.3.6.1.4.1.11863.6.32.1.2.2.2.1.15	INTEGER	read-only	The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.
tpSnmpRmonEventCtrl	1.3.6.1.4.1.11863.6.32.1.2.3
tpSnmpRmonEventCtrlTable	1.3.6.1.4.1.11863.6.32.1.2.3.1		not-accessible	A list of SNMP RMON EVENT control entries.
tpSnmpRmonEventCtrlEntry	1.3.6.1.4.1.11863.6.32.1.2.3.1.1		not-accessible	RMON (Remote Monitoring), basing on SNMP (Simple Network Management Protocol) architecture, functions to monitor the network. Event Group, as one of the commonly used RMON Groups, is used to define RMON events. Alarms occur when an event is detected.
INT tpSnmpRmonEventCtrlIndex	1.3.6.1.4.1.11863.6.32.1.2.3.1.1.1	INTEGER	read-only	The index of this entry.
OCT tpSnmpRmonEventCtrlUserName	1.3.6.1.4.1.11863.6.32.1.2.3.1.1.2	OCTET STRING	read-write	The name of the User or the community to which the event belongs.
OCT tpSnmpRmonEventCtrlDesc	1.3.6.1.4.1.11863.6.32.1.2.3.1.1.3	OCTET STRING	read-write	Description which is given to the event for identification.
INT tpSnmpRmonEventCtrlType	1.3.6.1.4.1.11863.6.32.1.2.3.1.1.4	INTEGER	read-write	The event type, which determines the act way of the network device in response to an event. none(1),no processing. log(2),logging the event. snmptrap(3),sending trap messages to the management station. logandtrap(4),logging the event and sending trap messages to the management station.
OCT tpSnmpRmonEventCtrlOwner	1.3.6.1.4.1.11863.6.32.1.2.3.1.1.5	OCTET STRING	read-write	The name of the device or user that defined the entry.
INT tpSnmpRmonEventCtrlStatus	1.3.6.1.4.1.11863.6.32.1.2.3.1.1.6	INTEGER	read-write	Enable/Disable the corresponding event entry. disable(0),disable the event entry. enable(1),enable the event entry.
tpSnmpRmonEventLogTable	1.3.6.1.4.1.11863.6.32.1.2.3.2		not-accessible	A list of log that have been logged.
tpSnmpRmonEventLogEntry	1.3.6.1.4.1.11863.6.32.1.2.3.2.1		not-accessible	A set of data describing an event that has been logged. For example, an instance of the logDescription object might be named logDescription.6.47
INT tpSnmpRmonEventLogEventIndex	1.3.6.1.4.1.11863.6.32.1.2.3.2.1.1	INTEGER	read-only	The event entry that generated this log entry. The log identified by a particular value of this index is associated with the same eventEntry as identified by the same value of eventIndex.
INT tpSnmpRmonEventLogIndex	1.3.6.1.4.1.11863.6.32.1.2.3.2.1.2	INTEGER	read-only	An index that uniquely identifies an entry in the log table amongst those generated by the same eventEntries. These indexes are assigned beginning with 1 and increase by one with each new log entry. The association between values of logIndex and logEntries is fixed for the lifetime of each logEntry. The agent may choose to delete the oldest instances of logEntry as required because of lack of memory. It is an implementation-specific matter as to when this deletion may occur.
TIK tpSnmpRmonEventLogTime	1.3.6.1.4.1.11863.6.32.1.2.3.2.1.3	TimeTicks	read-only	The value of sysUpTime when this log entry was created.
OCT tpSnmpRmonEventLogDescription	1.3.6.1.4.1.11863.6.32.1.2.3.2.1.4	OCTET STRING	read-only	An implementation dependent description of the event that activated this log entry.
tpSnmpRmonAlarmCtrl	1.3.6.1.4.1.11863.6.32.1.2.4
tpSnmpRmonAlarmCtrlTable	1.3.6.1.4.1.11863.6.32.1.2.4.1		not-accessible	A list of SNMP RMON EVENT control entries.
tpSnmpRmonAlarmCtrlEntry	1.3.6.1.4.1.11863.6.32.1.2.4.1.1		not-accessible	Alarm Group is one of the commonly used RMON Groups. RMON alarm management allows monitoring the specific alarm variables. When the value of a monitored variable exceeds the threshold, an alarm event is generated, which triggers the switch to act in the set way.
INT tpSnmpRmonAlarmCtrlIndex	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.1	INTEGER	read-only	The index of this entry.
INT tpSnmpRmonAlarmCtrlVariable	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.2	INTEGER	read-write	The packet type that to be count.
INT tpSnmpRmonAlarmCtrlStatisticsIndex	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.3	INTEGER	read-write	The index of the statistics entry relative with this alarm entry.
INT tpSnmpRmonAlarmCtrlSampleType	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.4	INTEGER	read-write	The method of sampling the selected variable and calculating the value to be compared against the thresholds. absoluteValue(1),compares the values directly with the thresholds at the end of the sampling interval. deltaValue(2),subtracts the last sampled value from the current value. The difference in the values is compared to the threshold.
INT tpSnmpRmonAlarmCtrlRisingThreshold	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.5	INTEGER	read-write	The rising counter value that triggers the rise hold alarm.
INT tpSnmpRmonAlarmCtrlRisingEvent	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.6	INTEGER	read-write	The index of the corresponding event which will be triggered if the sampled value is larger than the Rise Hold.
INT tpSnmpRmonAlarmCtrlFallingThreshold	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.7	INTEGER	read-write	The falling counter value that triggers the fall hold alarm.
INT tpSnmpRmonAlarmCtrlFallingEvent	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.8	INTEGER	read-write	The index of the corresponding event which will be triggered if the sampled value is lower than the Fall Hold.
INT tpSnmpRmonAlarmCtrlStartUp	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.9	INTEGER	read-write	Specify the type of the alarm. risingAlarm(1),When the sampled value exceeds the Rise Hold, an alarm event is triggered. fallingAlarm(2),When the sampled value is under the Fall Hold, an alarm event is triggered. risingOrFallingAlarm(3),The alarm event will be triggered either the sampled value exceeds the Rise Hold or is under the Fall Hold.
INT tpSnmpRmonAlarmCtrlInterval	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.10	INTEGER	read-write	The alarm interval time in seconds. 10sec-3600sec.
OCT tpSnmpRmonAlarmCtrlOwner	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.11	OCTET STRING	read-write	The name of the device or user that defined the entry.
INT tpSnmpRmonAlarmCtrlStatus	1.3.6.1.4.1.11863.6.32.1.2.4.1.1.12	INTEGER	read-write	Enable/Disable the corresponding alarm entry. disable(0),disable the alarm entry. enable(1),enable the alarm entry

RFC description

Provides RMON (Remote Monitoring) statistics, history, events and alarms configuration and monitoring for TP-Link network interfaces.

Start monitoring TP-Link managed switches (RMON stats/history/alarm-threshold status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TPLINK-SNMPRMON-MIB