All MIBs › PETH-MIB › pethPsePortPowerIdPairs
pethPsePortPowerIdPairs
Module: PETH-MIB
OID (symbolic): PETH-MIB::pethPsePortPowerIdPairs
OID (numeric): 1.3.6.1.2.1.10.7.20.1.1.1.5
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: Describes or controls the pairs in use. If the value of pethPsePortPowerIdpairsControl is true, thisobject is writable. A value of signal(1) menas that the signal pairs only are in use. A value of spare(2) means that the spare pairs only are in use. A value of both(3) means that both the signal and the spare pairs are in use.
What is pethPsePortPowerIdPairs?
This value describes or, when pethPsePortPowerIdPairsControl is true, controls which wire pairs the port uses to deliver PoE power: signal(1) pairs only, spare(2) pairs only, or both(3). An admin adjusts this on hardware that supports alternative power-pair modes to match the cabling scheme in use, such as older 10/100 cabling where spare pairs are otherwise unused. Setting pethPsePortPowerIdPairs to both(3) enables the port to source power over both pair sets simultaneously where supported.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.2.1.10.7.20.1.1.1.5 snmpwalk -v2c -c public <target> PETH-MIB::pethPsePortPowerIdPairs
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.2.1.10.7.20.1.1.1.5.1 snmpget -v2c -c public <target> PETH-MIB::pethPsePortPowerIdPairs.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.2.1.10.7.20.1.1.1.5.1 i <value>
Start monitoring vendor-neutral, standards-based MIB, RFC 3621 (Power over Ethernet, PSE/PD) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the PETH-MIB::pethPsePortPowerIdPairs OID value, configure state conditions and alerts, and monitor any vendor-neutral, standards-based MIB, RFC 3621 (Power over Ethernet, PSE/PD) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.2 | mgmt | APERTUS-NPG-MIB |
| 1.3.6.1.2.1 | mib_2 | AXON-MIB |
| 1.3.6.1.2.1.10 | transmission | CHECKPOINT-MIB-2 |
| 1.3.6.1.2.1.10.7 | dot3 | EtherLike-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.2.1.10.7.20 | powerEthernetMIB | PETH-MIB |
| 1.3.6.1.2.1.10.7.20.1 | pethObjects | PETH-MIB |
| 1.3.6.1.2.1.10.7.20.1.1 | pethPsePortTable | PETH-MIB |
| 1.3.6.1.2.1.10.7.20.1.1.1 | pethPsePortEntry | PETH-MIB |
| 1.3.6.1.2.1.10.7.20.1.1.1.5 | pethPsePortPowerIdPairs | PETH-MIB |