NOVELSAT-COMMON-MIB

All MIBs › NOVELSAT-COMMON-MIB

Organization: Novelsat

Last Updated: 2010-09-12

Category: Satellite and VSAT

Description: Defines common base objects and textual conventions shared across Novelsat VSAT satellite modem MIB modules.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NOVELSAT-COMMON-MIB?

NOVELSAT-COMMON-MIB defines textual conventions and shared base objects used across Novelsat's family of VSAT satellite modem MIB modules, covering management-interface network configuration and system-wide alarm/event handling. It exposes management host IP addressing (IP, mask, gateway, DHCP, DNS), over-the-air (OTA) update networking settings, firmware rollback mode and timeout, management rate limiting, and a shared alarms/events table used by other Novelsat modules. Its monitoring relevance centers on configuration and software-management status -- the rollback-mode/timeout objects govern what happens if an OTA firmware update fails, and the shared alarm/event table is where fault conditions from the actual product-specific modules (registered under the ns1000/ns2000/ns3000 branches) get reported. As a "common" MIB it is explicitly a dependency for the product-specific Novelsat MIBs, which import its textual conventions and alarm table structure rather than redefining them. It is deployed across Novelsat NS1000/NS2000/NS3000 series satellite modems used in VSAT and satellite backhaul networks. Engineers can download the NOVELSAT-COMMON-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NOVELSAT-COMMON-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Novelsat NS1000/NS2000/NS3000 series VSAT satellite modems

Monitoring Examples

An operator managing a fleet of Novelsat satellite modems would poll nsCommonConfigMgmtHostIP and nsCommonConfigMgmtHostDHCP to audit whether each unit's management interface is correctly addressed for remote access. Before pushing a firmware update, they would check nsCommonConfigMgmtRollbackMode and nsCommonConfigMgmtRollbackTimeout to confirm the modem will automatically revert if the OTA update (delivered via nsCommonConfigMgmtOtaIP) fails to come up. Ongoing fault conditions across the fleet would be visible by walking nsCommonConfigAlarmsEventsTable, shared by the product-specific ns1000/ns2000/ns3000 modules.

What Can Be Monitored

management interface IP configuration
OTA update network settings
firmware rollback mode/timeout
management rate limit setting
alarm/event log entries

Imported Objects

From HCNUM-TC

CounterBasedGauge64

From ITU-ALARM-TC-MIB

ItuPerceivedSeverity

From NOVELSAT-ROOT-MIB

nsRoot

MODULE-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus

How to Use in IPNetwork Monitor

Example using nsCommonMonitorNetworkQueuesStatisticsEnqueuedBytes OID:

Select a Novelsat NS1000/NS2000/NS3000 series VSAT satellite modem (shared conventions) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type nsCommonMonitorNetworkQueuesStatisticsEnqueuedBytes into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the network Queues Statistics enqueued bytes value. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
nsCommon	1.3.6.1.4.1.37576.2			Novelsat Common MIB
nsCommonConfig	1.3.6.1.4.1.37576.2.1			Common MIB branch that holds all common configuration parameters.
nsCommonConfig10MhzClock	1.3.6.1.4.1.37576.2.1.4			Common MIB branch that holds all Common 10Mhz clock parameters.
INT nsCommonConfig10MhzClockLnbRefClock	1.3.6.1.4.1.37576.2.1.4.4	INTEGER	read-write	This parameter holds LNB reference clock state.
INT nsCommonConfig10MhzClockOut	1.3.6.1.4.1.37576.2.1.4.2	INTEGER	read-write	This parameter holds clock out state.
INT nsCommonConfig10MhzClockSource	1.3.6.1.4.1.37576.2.1.4.1	INTEGER	read-write	This parameter holds clock source.
INT nsCommonConfig10MhzClockTxPortClock	1.3.6.1.4.1.37576.2.1.4.3	INTEGER	read-write	This parameter holds TX port clock state.
nsCommonConfigAlarmsEvents	1.3.6.1.4.1.37576.2.1.11			Common MIB branch that holds all Common Alarms and Events parameters.
nsCommonConfigAlarmsEventsEntry	1.3.6.1.4.1.37576.2.1.11.1.1		not-accessible	Conceptual row in table for each alarm or event.
U32 nsCommonConfigAlarmsEventsIndex	1.3.6.1.4.1.37576.2.1.11.1.1.1	Unsigned32	not-accessible	This parameter holds alarm index.
INT nsCommonConfigAlarmsEventsMask	1.3.6.1.4.1.37576.2.1.11.1.1.3	INTEGER	read-create	This parameter holds alarm mask.
STR nsCommonConfigAlarmsEventsName	1.3.6.1.4.1.37576.2.1.11.1.1.2	DisplayString	read-only	This parameter holds alarm name.
INT nsCommonConfigAlarmsEventsRelayMask	1.3.6.1.4.1.37576.2.1.11.1.1.4	INTEGER	read-create	This parameter holds alarm mask.
nsCommonConfigAlarmsEventsTable	1.3.6.1.4.1.37576.2.1.11.1		not-accessible	A list of Alarms and Events parameters
DAT nsCommonConfigDateAndTime	1.3.6.1.4.1.37576.2.1.6.1	DateAndTime	read-write	This parameter holds system date and time.
nsCommonConfigDateTime	1.3.6.1.4.1.37576.2.1.6			Common MIB branch that holds all Common serial port parameters.
nsCommonConfigManagementIP	1.3.6.1.4.1.37576.2.1.3			Common MIB branch that holds all Common management IP parameters.
nsCommonConfigManagementOta	1.3.6.1.4.1.37576.2.1.8			This branch is no longer supported. OTA support is now performed using Network Interfaces table
nsCommonConfigManagementRateLimiter	1.3.6.1.4.1.37576.2.1.10			Common MIB branch that holds all Common management rate limiter parameters.
nsCommonConfigManagementRollback	1.3.6.1.4.1.37576.2.1.9			Common MIB branch that holds all rollback parameters.
INT nsCommonConfigMgmtHostDHCP	1.3.6.1.4.1.37576.2.1.3.4	INTEGER	read-write	This parameter is no longer supported
IP nsCommonConfigMgmtHostDNS	1.3.6.1.4.1.37576.2.1.3.5	IpAddress	read-write	This parameter is no longer supported
IP nsCommonConfigMgmtHostGW	1.3.6.1.4.1.37576.2.1.3.3	IpAddress	read-write	This parameter holds product gateway address.
IP nsCommonConfigMgmtHostIP	1.3.6.1.4.1.37576.2.1.3.1	IpAddress	read-write	This parameter holds product IP address.
IP nsCommonConfigMgmtHostMask	1.3.6.1.4.1.37576.2.1.3.2	IpAddress	read-write	This parameter holds product network mask address.
IP nsCommonConfigMgmtOtaIP	1.3.6.1.4.1.37576.2.1.8.1	IpAddress	read-write	This parameter is no longer supported. OTA support is now performed using Network Interfaces table
IP nsCommonConfigMgmtOtaMask	1.3.6.1.4.1.37576.2.1.8.2	IpAddress	read-write	This parameter is no longer supported. OTA support is now performed using Network Interfaces table
U32 nsCommonConfigMgmtRateLimit	1.3.6.1.4.1.37576.2.1.10.1	Unsigned32	read-write	This parameter holds management rate limit in Kbps.
INT nsCommonConfigMgmtRollbackMode	1.3.6.1.4.1.37576.2.1.9.1	INTEGER	read-write	This parameter holds rollback mode.
U32 nsCommonConfigMgmtRollbackTimeout	1.3.6.1.4.1.37576.2.1.9.2	Unsigned32	read-write	This parameter holds rollback timeout in minutes.
nsCommonConfigNetwork	1.3.6.1.4.1.37576.2.1.7			Common MIB branch that holds all Common network parameters.
nsCommonConfigNetworkBwManagement	1.3.6.1.4.1.37576.2.1.7.6.4			Common MIB branch that holds all Common bandwidth management parameters. Not yet supported.
INT nsCommonConfigNetworkBwManagementAdminStatus	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.3	INTEGER	read-create	This parameter holds bandwidth management's administrative status.
U32 nsCommonConfigNetworkBwManagementCBS	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.5	Unsigned32	read-create	This parameter holds bandwidth management's CBS in bits.
U32 nsCommonConfigNetworkBwManagementCIR	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.4	Unsigned32	read-create	This parameter holds bandwidth management's CIR in bps.
U32 nsCommonConfigNetworkBwManagementEBS	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.7	Unsigned32	read-create	This parameter holds bandwidth management's EBS in bits.
U32 nsCommonConfigNetworkBwManagementEIR	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.6	Unsigned32	read-create	This parameter holds bandwidth management's EIR in bps.
nsCommonConfigNetworkBwManagementEntry	1.3.6.1.4.1.37576.2.1.7.6.4.1.1		not-accessible	Conceptual row in table for each neighbor.
U32 nsCommonConfigNetworkBwManagementIndex	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.1	Unsigned32	not-accessible	This parameter holds bandwidth management's number.
U32 nsCommonConfigNetworkBwManagementNeighborIndex	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.2	Unsigned32	read-create	This parameter holds bandwidth management's neighbor's index.
ROW nsCommonConfigNetworkBwManagementNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.11	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
U32 nsCommonConfigNetworkBwManagementPercentage	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.10	Unsigned32	read-only	This parameter holds bandwidth management's percentage in hundreds of percentage.
INT nsCommonConfigNetworkBwManagementRefFecRate	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.9	INTEGER	read-create	This parameter holds bandwidth management's reference FEC rate.
INT nsCommonConfigNetworkBwManagementRefModulation	1.3.6.1.4.1.37576.2.1.7.6.4.1.1.8	INTEGER	read-create	This parameter holds bandwidth management's reference modulation.
nsCommonConfigNetworkBwManagementTable	1.3.6.1.4.1.37576.2.1.7.6.4.1		not-accessible	A list of BwManagement parameters
nsCommonConfigNetworkClassification	1.3.6.1.4.1.37576.2.1.7.6.1			Common MIB branch that holds all Common classification parameters.
nsCommonConfigNetworkClassification802	1.3.6.1.4.1.37576.2.1.7.6.1.2			Common MIB branch that holds all Common classification parameters.
INT nsCommonConfigNetworkClassification802CoS	1.3.6.1.4.1.37576.2.1.7.6.1.2.1.1.2	INTEGER	read-write	This parameter holds classification 802.1p CoS.
nsCommonConfigNetworkClassification802Entry	1.3.6.1.4.1.37576.2.1.7.6.1.2.1.1		not-accessible	Conceptual row in table for each neighbor.
U32 nsCommonConfigNetworkClassification802Priority	1.3.6.1.4.1.37576.2.1.7.6.1.2.1.1.1	Unsigned32	not-accessible	This parameter holds classification 802.1p priority.
nsCommonConfigNetworkClassification802Table	1.3.6.1.4.1.37576.2.1.7.6.1.2.1		not-accessible	A list of Classification802 parameters
nsCommonConfigNetworkClassificationMf	1.3.6.1.4.1.37576.2.1.7.6.1.4			Common MIB branch that holds all Common classification parameters.
INT nsCommonConfigNetworkClassificationMfAdminStatus	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.3	INTEGER	read-create	This parameter holds classification MF's administrative status.
INT nsCommonConfigNetworkClassificationMfCoS	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.16	INTEGER	read-create	This parameter holds classification MF CoS.
IP nsCommonConfigNetworkClassificationMfDestIpAddressHigh	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.8	IpAddress	read-create	This parameter holds classification MF destination IP Address high.
IP nsCommonConfigNetworkClassificationMfDestIpAddressLow	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.9	IpAddress	read-create	This parameter holds classification MF destination IP Address low.
U32 nsCommonConfigNetworkClassificationMfDestPortHigh	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.14	Unsigned32	read-create	This parameter holds classification MF destination port high.
U32 nsCommonConfigNetworkClassificationMfDestPortLow	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.15	Unsigned32	read-create	This parameter holds classification MF destination port low.
nsCommonConfigNetworkClassificationMfEntry	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1		not-accessible	Conceptual row in table for each neighbor.
STR nsCommonConfigNetworkClassificationMfName	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.2	DisplayString	read-create	This parameter holds classification MF name.
ROW nsCommonConfigNetworkClassificationMfNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.17	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
U32 nsCommonConfigNetworkClassificationMfPriority	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.1	Unsigned32	not-accessible	This parameter holds classification MF priority.
U32 nsCommonConfigNetworkClassificationMfProtocol	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.11	Unsigned32	read-create	This parameter holds classification MF protocol.
INT nsCommonConfigNetworkClassificationMfProtocolStatus	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.10	INTEGER	read-create	This parameter holds classification MF's protocol status.
IP nsCommonConfigNetworkClassificationMfSrcIpAddressHigh	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.6	IpAddress	read-create	This parameter holds classification MF source IP Address high.
IP nsCommonConfigNetworkClassificationMfSrcIpAddressLow	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.7	IpAddress	read-create	This parameter holds classification MF source IP Address low.
U32 nsCommonConfigNetworkClassificationMfSrcPortHigh	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.12	Unsigned32	read-create	This parameter holds classification MF source port high.
U32 nsCommonConfigNetworkClassificationMfSrcPortLow	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.13	Unsigned32	read-create	This parameter holds classification MF source port low.
nsCommonConfigNetworkClassificationMfTable	1.3.6.1.4.1.37576.2.1.7.6.1.4.1		not-accessible	A list of Classification Mf parameters
U32 nsCommonConfigNetworkClassificationMfVidHigh	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.4	Unsigned32	read-create	This parameter holds classification MF VID high.
U32 nsCommonConfigNetworkClassificationMfVidLow	1.3.6.1.4.1.37576.2.1.7.6.1.4.1.1.5	Unsigned32	read-create	This parameter holds classification MF VID low.
INT nsCommonConfigNetworkClassificationMode	1.3.6.1.4.1.37576.2.1.7.6.1.1	INTEGER	read-write	This parameter holds classification's method.
nsCommonConfigNetworkClassificationTos	1.3.6.1.4.1.37576.2.1.7.6.1.3			Common MIB branch that holds all Common classification parameters.
INT nsCommonConfigNetworkClassificationTosColor	1.3.6.1.4.1.37576.2.1.7.6.1.3.1.1.6	INTEGER	read-create	This parameter holds classification TOS Color. Not yet supported.
INT nsCommonConfigNetworkClassificationTosCoS	1.3.6.1.4.1.37576.2.1.7.6.1.3.1.1.4	INTEGER	read-create	This parameter holds classification TOS CoS.
nsCommonConfigNetworkClassificationTosEntry	1.3.6.1.4.1.37576.2.1.7.6.1.3.1.1		not-accessible	Conceptual row in table for each neighbor.
U32 nsCommonConfigNetworkClassificationTosFieldMask	1.3.6.1.4.1.37576.2.1.7.6.1.3.1.1.3	Unsigned32	read-create	This parameter holds classification TOS field mask.
U32 nsCommonConfigNetworkClassificationTosFieldValue	1.3.6.1.4.1.37576.2.1.7.6.1.3.1.1.2	Unsigned32	read-create	This parameter holds classification TOS field value.
ROW nsCommonConfigNetworkClassificationTosNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.6.1.3.1.1.5	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
U32 nsCommonConfigNetworkClassificationTosPriority	1.3.6.1.4.1.37576.2.1.7.6.1.3.1.1.1	Unsigned32	not-accessible	This parameter holds classification TOS priority.
nsCommonConfigNetworkClassificationTosTable	1.3.6.1.4.1.37576.2.1.7.6.1.3.1		not-accessible	A list of Classification Tos parameters
nsCommonConfigNetworkForwardingMode	1.3.6.1.4.1.37576.2.1.7.1			Common MIB branch that holds all Common forwarding mode parameters.
nsCommonConfigNetworkInterfaces	1.3.6.1.4.1.37576.2.1.7.2			Common MIB branch that holds all Common Interfaces parameters.
INT nsCommonConfigNetworkInterfacesAcmControl	1.3.6.1.4.1.37576.2.1.7.2.1.1.13	INTEGER	read-create	This parameter holds interface's Acm control status.
INT nsCommonConfigNetworkInterfacesAdminStatus	1.3.6.1.4.1.37576.2.1.7.2.1.1.3	INTEGER	read-create	This parameter holds interface's administrative status.
INT nsCommonConfigNetworkInterfacesEncapsulation	1.3.6.1.4.1.37576.2.1.7.2.1.1.11	INTEGER	read-create	This parameter holds interface's administrative status.
nsCommonConfigNetworkInterfacesEntry	1.3.6.1.4.1.37576.2.1.7.2.1.1		not-accessible	Conceptual row in table for each neighbor.
U32 nsCommonConfigNetworkInterfacesIndex	1.3.6.1.4.1.37576.2.1.7.2.1.1.1	Unsigned32	not-accessible	This parameter holds interface's index.
IP nsCommonConfigNetworkInterfacesIp	1.3.6.1.4.1.37576.2.1.7.2.1.1.8	IpAddress	read-create	This parameter holds interface's IP address.
STR nsCommonConfigNetworkInterfacesMac	1.3.6.1.4.1.37576.2.1.7.2.1.1.9	DisplayString	read-create	This parameter holds interface's MAC address.
INT nsCommonConfigNetworkInterfacesManagementControl	1.3.6.1.4.1.37576.2.1.7.2.1.1.12	INTEGER	read-create	This parameter holds interface's management control status.
U32 nsCommonConfigNetworkInterfacesMtu	1.3.6.1.4.1.37576.2.1.7.2.1.1.6	Unsigned32	read-create	This parameter holds interface's MTU.
STR nsCommonConfigNetworkInterfacesName	1.3.6.1.4.1.37576.2.1.7.2.1.1.2	DisplayString	read-create	This parameter holds interface's name.
ROW nsCommonConfigNetworkInterfacesNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.2.1.1.14	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
INT nsCommonConfigNetworkInterfacesPortType	1.3.6.1.4.1.37576.2.1.7.2.1.1.4	INTEGER	read-create	This parameter holds interface's port type.
IP nsCommonConfigNetworkInterfacesSubnetMask	1.3.6.1.4.1.37576.2.1.7.2.1.1.10	IpAddress	read-create	This parameter holds interface's subnet mask.
nsCommonConfigNetworkInterfacesTable	1.3.6.1.4.1.37576.2.1.7.2.1		not-accessible	A list of Interfaces parameters
U32 nsCommonConfigNetworkInterfacesVlan	1.3.6.1.4.1.37576.2.1.7.2.1.1.7	Unsigned32	read-create	This parameter holds interface's vlan/pid.
INT nsCommonConfigNetworkMode	1.3.6.1.4.1.37576.2.1.7.1.1	INTEGER	read-write	This parameter holds networking mode.
nsCommonConfigNetworkNeighbors	1.3.6.1.4.1.37576.2.1.7.3			Common MIB branch that holds all Common Neighbors parameters.
nsCommonConfigNetworkNeighborsEntry	1.3.6.1.4.1.37576.2.1.7.3.1.1		not-accessible	Conceptual row in table for each neighbor.
INT nsCommonConfigNetworkNeighborsFecRate	1.3.6.1.4.1.37576.2.1.7.3.1.1.8	INTEGER	read-create	This parameter holds neighbor's modulation.
U32 nsCommonConfigNetworkNeighborsIfIndex	1.3.6.1.4.1.37576.2.1.7.3.1.1.3	Unsigned32	read-create	This parameter holds interface's index that is directly connected to this neighbor.
U32 nsCommonConfigNetworkNeighborsIndex	1.3.6.1.4.1.37576.2.1.7.3.1.1.1	Unsigned32	not-accessible	This parameter holds neighbor's index.
IP nsCommonConfigNetworkNeighborsIp	1.3.6.1.4.1.37576.2.1.7.3.1.1.4	IpAddress	read-create	This parameter holds neighbor's IP address.
STR nsCommonConfigNetworkNeighborsMac	1.3.6.1.4.1.37576.2.1.7.3.1.1.5	DisplayString	read-create	This parameter holds neighbor's MAC address.
INT nsCommonConfigNetworkNeighborsModulation	1.3.6.1.4.1.37576.2.1.7.3.1.1.7	INTEGER	read-create	This parameter holds neighbor's modulation.
STR nsCommonConfigNetworkNeighborsName	1.3.6.1.4.1.37576.2.1.7.3.1.1.2	DisplayString	read-create	This parameter holds neighbor's name.
ROW nsCommonConfigNetworkNeighborsNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.3.1.1.9	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
IP nsCommonConfigNetworkNeighborsSignalingIp	1.3.6.1.4.1.37576.2.1.7.3.1.1.6	IpAddress	read-create	This parameter holds neighbor's remote IP address.
nsCommonConfigNetworkNeighborsTable	1.3.6.1.4.1.37576.2.1.7.3.1		not-accessible	A list of Neighbors parameters
nsCommonConfigNetworkPolicyRoute	1.3.6.1.4.1.37576.2.1.7.4.1			Common MIB branch that holds all Common PolicyRoute parameters.
nsCommonConfigNetworkPolicyRouteEntry	1.3.6.1.4.1.37576.2.1.7.4.1.1.1		not-accessible	Conceptual row in table for each neighbor.
U32 nsCommonConfigNetworkPolicyRouteIndex	1.3.6.1.4.1.37576.2.1.7.4.1.1.1.1	Unsigned32	not-accessible	This parameter holds routing policy's index.
U32 nsCommonConfigNetworkPolicyRouteInputInterfaceId	1.3.6.1.4.1.37576.2.1.7.4.1.1.1.2	Unsigned32	read-create	This parameter holds interface's index. Must exist in Interfaces' configuration table
ROW nsCommonConfigNetworkPolicyRouteNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.4.1.1.1.4	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
U32 nsCommonConfigNetworkPolicyRouteRoutingTableId	1.3.6.1.4.1.37576.2.1.7.4.1.1.1.3	Unsigned32	read-create	This parameter holds routing policy's table ID.
nsCommonConfigNetworkPolicyRouteTable	1.3.6.1.4.1.37576.2.1.7.4.1.1		not-accessible	A list of PolicyRoute parameters
nsCommonConfigNetworkQoS	1.3.6.1.4.1.37576.2.1.7.6			Common MIB branch that holds all Common QoS parameters.
nsCommonConfigNetworkQueues	1.3.6.1.4.1.37576.2.1.7.6.2			Common MIB branch that holds all Common Queues parameters.
U32 nsCommonConfigNetworkQueuesCos	1.3.6.1.4.1.37576.2.1.7.6.2.1.1.1	Unsigned32	not-accessible	This parameter holds queue's number.
INT nsCommonConfigNetworkQueuesDropDiscipline	1.3.6.1.4.1.37576.2.1.7.6.2.1.1.5	INTEGER	read-write	This parameter holds queue's scheduling method.
nsCommonConfigNetworkQueuesEntry	1.3.6.1.4.1.37576.2.1.7.6.2.1.1		not-accessible	Conceptual row in table for each neighbor.
U32 nsCommonConfigNetworkQueuesQueueDepth	1.3.6.1.4.1.37576.2.1.7.6.2.1.1.4	Unsigned32	read-write	This parameter holds queue's max queue depth.
INT nsCommonConfigNetworkQueuesSchedulingMethod	1.3.6.1.4.1.37576.2.1.7.6.2.1.1.2	INTEGER	read-write	This parameter holds queue's scheduling method.
nsCommonConfigNetworkQueuesTable	1.3.6.1.4.1.37576.2.1.7.6.2.1		not-accessible	A list of Queues parameters
U32 nsCommonConfigNetworkQueuesWeight	1.3.6.1.4.1.37576.2.1.7.6.2.1.1.3	Unsigned32	read-write	This parameter holds queue's weight.
nsCommonConfigNetworkRemoteScheduling	1.3.6.1.4.1.37576.2.1.7.6.3			Common MIB branch that holds all Common neighbor scheduling parameters. Not yet supported...
INT nsCommonConfigNetworkRemoteSchedulingCosSignificance	1.3.6.1.4.1.37576.2.1.7.6.3.3	INTEGER	read-write	This parameter holds neighbor scheduling's COS significance. Not yet supported.
INT nsCommonConfigNetworkRemoteSchedulingFrameMerging	1.3.6.1.4.1.37576.2.1.7.6.3.2	INTEGER	read-write	This parameter holds neighbor scheduling's frame merging status. Not yet supported.
INT nsCommonConfigNetworkRemoteSchedulingMethod	1.3.6.1.4.1.37576.2.1.7.6.3.1	INTEGER	read-write	This parameter holds neighbor scheduling's method. Not yet supported.
nsCommonConfigNetworkRoutes	1.3.6.1.4.1.37576.2.1.7.4.2			Common MIB branch that holds all Common Routes parameters.
INT nsCommonConfigNetworkRoutesAdminStatus	1.3.6.1.4.1.37576.2.1.7.4.2.1.1.5	INTEGER	read-create	This parameter holds interface's administrative status.
IP nsCommonConfigNetworkRoutesDestIpAddress	1.3.6.1.4.1.37576.2.1.7.4.2.1.1.1	IpAddress	not-accessible	This parameter holds routes' destination IP address.
IP nsCommonConfigNetworkRoutesDestSubnetMask	1.3.6.1.4.1.37576.2.1.7.4.2.1.1.2	IpAddress	not-accessible	This parameter holds routes' destination subnet mask.
nsCommonConfigNetworkRoutesEntry	1.3.6.1.4.1.37576.2.1.7.4.2.1.1		not-accessible	Conceptual row in table for each neighbor.
IP nsCommonConfigNetworkRoutesNexthopIpAddress	1.3.6.1.4.1.37576.2.1.7.4.2.1.1.3	IpAddress	not-accessible	This parameter holds routes' nexthop IP address.
ROW nsCommonConfigNetworkRoutesNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.4.2.1.1.6	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
nsCommonConfigNetworkRoutesTable	1.3.6.1.4.1.37576.2.1.7.4.2.1		not-accessible	A list of Routes parameters
U32 nsCommonConfigNetworkRoutesTableId	1.3.6.1.4.1.37576.2.1.7.4.2.1.1.4	Unsigned32	not-accessible	This parameter holds routes' table ID.
nsCommonConfigNetworkRouting	1.3.6.1.4.1.37576.2.1.7.4			Common MIB branch that holds all Common PolicyRoute parameters.
nsCommonConfigNetworkVlanSwitching	1.3.6.1.4.1.37576.2.1.7.5			Common MIB branch that holds all Common VlanSwitching parameters.
INT nsCommonConfigNetworkVlanSwitchingAdminStatus	1.3.6.1.4.1.37576.2.1.7.5.1.1.3	INTEGER	read-create	This parameter holds VLAN switching's administrative status.
nsCommonConfigNetworkVlanSwitchingEntry	1.3.6.1.4.1.37576.2.1.7.5.1.1		not-accessible	Conceptual row in table for each neighbor.
U32 nsCommonConfigNetworkVlanSwitchingNeighborIndex	1.3.6.1.4.1.37576.2.1.7.5.1.1.2	Unsigned32	read-create	This parameter holds VLAN switching's neighbor's index. Must exist in Neighbors' configuration table.
ROW nsCommonConfigNetworkVlanSwitchingNotifyRowStatus	1.3.6.1.4.1.37576.2.1.7.5.1.1.4	RowStatus	read-create	Used to create new rows or delete in the table. Note that all rows are active(1) at all times, since default values are given to empty parameters. Value createAndGo(4) is used when all row parameters are inserted at once, while createAndWait(5) is used to create row with default values. Value destroy(6) is used to remove a row
nsCommonConfigNetworkVlanSwitchingTable	1.3.6.1.4.1.37576.2.1.7.5.1		not-accessible	A list of VlanSwitching parameters
U32 nsCommonConfigNetworkVlanSwitchingVid	1.3.6.1.4.1.37576.2.1.7.5.1.1.1	Unsigned32	not-accessible	This parameter holds VLAN switching's VID.
nsCommonConfigSerialPort	1.3.6.1.4.1.37576.2.1.5			Common MIB branch that holds all Common serial port parameters.
INT nsCommonConfigSerialPortBaudRate	1.3.6.1.4.1.37576.2.1.5.1	INTEGER	read-write	This parameter holds serial port baud rate.
INT nsCommonConfigSerialPortDataBits	1.3.6.1.4.1.37576.2.1.5.3	INTEGER	read-write	This parameter holds serial port data bits.
INT nsCommonConfigSerialPortParity	1.3.6.1.4.1.37576.2.1.5.2	INTEGER	read-write	This parameter holds serial port parity.
INT nsCommonConfigSerialPortStopBit	1.3.6.1.4.1.37576.2.1.5.4	INTEGER	read-write	This parameter holds serial port stop bit.
nsCommonMonitor	1.3.6.1.4.1.37576.2.2			Common MIB branch that holds all Common status and alarms.
nsCommonMonitorAlarms	1.3.6.1.4.1.37576.2.2.1			Common MIB branch that holds all Common Alarms.
DAT nsCommonMonitorAlarmsDateAndTime	1.3.6.1.4.1.37576.2.2.1.1.1.5	DateAndTime	read-only	Date and Time of event
STR nsCommonMonitorAlarmsDescription	1.3.6.1.4.1.37576.2.2.1.1.1.9	DisplayString	read-only	Severity of event
nsCommonMonitorAlarmsEntry	1.3.6.1.4.1.37576.2.2.1.1.1		not-accessible	Conceptual row in table for each event.
STR nsCommonMonitorAlarmsEvent	1.3.6.1.4.1.37576.2.2.1.1.1.8	DisplayString	read-only	Severity of event
ITU nsCommonMonitorAlarmsSeverity	1.3.6.1.4.1.37576.2.2.1.1.1.6	ItuPerceivedSeverity	read-only	Severity of event
STR nsCommonMonitorAlarmsSource	1.3.6.1.4.1.37576.2.2.1.1.1.7	DisplayString	read-only	Severity of event
nsCommonMonitorAlarmsTable	1.3.6.1.4.1.37576.2.2.1.1		not-accessible	List of Alarms occured
C32 nsCommonMonitorAlarmsUtcNanoSecondsHigh	1.3.6.1.4.1.37576.2.2.1.1.1.3	Counter32	not-accessible	Seconds passed from EPOCH
C32 nsCommonMonitorAlarmsUtcNanoSecondsLow	1.3.6.1.4.1.37576.2.2.1.1.1.4	Counter32	not-accessible	Seconds passed from EPOCH
C32 nsCommonMonitorAlarmsUtcSecondsHigh	1.3.6.1.4.1.37576.2.2.1.1.1.1	Counter32	not-accessible	Seconds passed from EPOCH
C32 nsCommonMonitorAlarmsUtcSecondsLow	1.3.6.1.4.1.37576.2.2.1.1.1.2	Counter32	not-accessible	Seconds passed from EPOCH
NTF nsCommonMonitorEventNotification	1.3.6.1.4.1.37576.2.2.0.1			This notification is sent by the target when an event is triggered
nsCommonMonitorEvents	1.3.6.1.4.1.37576.2.2.2			Common MIB branch that holds all Common events.
DAT nsCommonMonitorEventsDateAndTime	1.3.6.1.4.1.37576.2.2.2.1.1.5	DateAndTime	read-only	Date and Time of event
STR nsCommonMonitorEventsDescription	1.3.6.1.4.1.37576.2.2.2.1.1.10	DisplayString	read-only	Severity of event
nsCommonMonitorEventsEntry	1.3.6.1.4.1.37576.2.2.2.1.1		not-accessible	Conceptual row in table for each event.
STR nsCommonMonitorEventsEvent	1.3.6.1.4.1.37576.2.2.2.1.1.9	DisplayString	read-only	Severity of event
ITU nsCommonMonitorEventsSeverity	1.3.6.1.4.1.37576.2.2.2.1.1.7	ItuPerceivedSeverity	read-only	Severity of event
STR nsCommonMonitorEventsSource	1.3.6.1.4.1.37576.2.2.2.1.1.8	DisplayString	read-only	Severity of event
nsCommonMonitorEventsTable	1.3.6.1.4.1.37576.2.2.2.1		not-accessible	List of Events occured
INT nsCommonMonitorEventsType	1.3.6.1.4.1.37576.2.2.2.1.1.6	INTEGER	read-only	Severity of event
C32 nsCommonMonitorEventsUtcNanoSecondsHigh	1.3.6.1.4.1.37576.2.2.2.1.1.3	Counter32	not-accessible	Seconds passed from EPOCH
C32 nsCommonMonitorEventsUtcNanoSecondsLow	1.3.6.1.4.1.37576.2.2.2.1.1.4	Counter32	not-accessible	Seconds passed from EPOCH
C32 nsCommonMonitorEventsUtcSecondsHigh	1.3.6.1.4.1.37576.2.2.2.1.1.1	Counter32	not-accessible	Seconds passed from EPOCH
C32 nsCommonMonitorEventsUtcSecondsLow	1.3.6.1.4.1.37576.2.2.2.1.1.2	Counter32	not-accessible	Seconds passed from EPOCH
nsCommonMonitorNetwork	1.3.6.1.4.1.37576.2.2.5			Common MIB branch that holds all network statuses.
nsCommonMonitorNetworkBwManagementStatisticsEntry	1.3.6.1.4.1.37576.2.2.5.5.1		not-accessible	Conceptual row in table for each event.
C64 nsCommonMonitorNetworkBwManagementStatisticsGreenPackets	1.3.6.1.4.1.37576.2.2.5.5.1.2	Counter64	read-only	Network BwManagement Statistics green packets value
C64 nsCommonMonitorNetworkBwManagementStatisticsGreenRates	1.3.6.1.4.1.37576.2.2.5.5.1.3	Counter64	read-only	Network BwManagement Statistics green rates value
C32 nsCommonMonitorNetworkBwManagementStatisticsNeighborIndex	1.3.6.1.4.1.37576.2.2.5.5.1.1	Counter32	not-accessible	Network BwManagementStatistics neighbor's index
C64 nsCommonMonitorNetworkBwManagementStatisticsRedPackets	1.3.6.1.4.1.37576.2.2.5.5.1.6	Counter64	read-only	Network BwManagement Statistics red packets value
C64 nsCommonMonitorNetworkBwManagementStatisticsRedRates	1.3.6.1.4.1.37576.2.2.5.5.1.7	Counter64	read-only	Network BwManagement Statistics red rates value
nsCommonMonitorNetworkBwManagementStatisticsTable	1.3.6.1.4.1.37576.2.2.5.5		not-accessible	List of interface statuses
C64 nsCommonMonitorNetworkBwManagementStatisticsYellowPackets	1.3.6.1.4.1.37576.2.2.5.5.1.4	Counter64	read-only	Network BwManagement Statistics yellow packets value
C64 nsCommonMonitorNetworkBwManagementStatisticsYellowRates	1.3.6.1.4.1.37576.2.2.5.5.1.5	Counter64	read-only	Network BwManagement Statistics yellow rates value
INT nsCommonMonitorNetworkInterfaceClrCmd	1.3.6.1.4.1.37576.2.2.5.6	INTEGER	read-write	Clear interfaces statistics counters command
nsCommonMonitorNetworkInterfaces	1.3.6.1.4.1.37576.2.2.5.1			Common MIB branch that holds all network interfaces statuses.
INT nsCommonMonitorNetworkInterfacesLanAdminStatus	1.3.6.1.4.1.37576.2.2.5.1.1.1.3	INTEGER	read-only	Network LAN Interfaces administrator status
nsCommonMonitorNetworkInterfacesLanEntry	1.3.6.1.4.1.37576.2.2.5.1.1.1		not-accessible	Conceptual row in table for each event.
C32 nsCommonMonitorNetworkInterfacesLanIndex	1.3.6.1.4.1.37576.2.2.5.1.1.1.1	Counter32	not-accessible	Network LAN Interfaces status index
IP nsCommonMonitorNetworkInterfacesLanIpAddress	1.3.6.1.4.1.37576.2.2.5.1.1.1.8	IpAddress	read-only	Network LAN Interfaces port status
STR nsCommonMonitorNetworkInterfacesLanMacAddress	1.3.6.1.4.1.37576.2.2.5.1.1.1.7	DisplayString	read-only	Network LAN Interfaces port status
STR nsCommonMonitorNetworkInterfacesLanName	1.3.6.1.4.1.37576.2.2.5.1.1.1.2	DisplayString	read-only	Network LAN Interfaces status name
INT nsCommonMonitorNetworkInterfacesLanOperStatus	1.3.6.1.4.1.37576.2.2.5.1.1.1.4	INTEGER	read-only	Network LAN Interfaces administrator status
U32 nsCommonMonitorNetworkInterfacesLanPort	1.3.6.1.4.1.37576.2.2.5.1.1.1.5	Unsigned32	read-only	Network LAN Interfaces port status
IP nsCommonMonitorNetworkInterfacesLanSubnetMask	1.3.6.1.4.1.37576.2.2.5.1.1.1.9	IpAddress	read-only	Network LAN Interfaces port status
nsCommonMonitorNetworkInterfacesLanTable	1.3.6.1.4.1.37576.2.2.5.1.1		not-accessible	List of interface statuses
U32 nsCommonMonitorNetworkInterfacesLanVlan	1.3.6.1.4.1.37576.2.2.5.1.1.1.6	Unsigned32	read-only	Network LAN Interfaces port status
INT nsCommonMonitorNetworkInterfacesSatAdminStatus	1.3.6.1.4.1.37576.2.2.5.1.2.1.3	INTEGER	read-only	Network SAT Interfaces administrator status
INT nsCommonMonitorNetworkInterfacesSatEncapsulation	1.3.6.1.4.1.37576.2.2.5.1.2.1.10	INTEGER	read-only	Network SAT Interfaces encapsulation status
nsCommonMonitorNetworkInterfacesSatEntry	1.3.6.1.4.1.37576.2.2.5.1.2.1		not-accessible	Conceptual row in table for each event.
C32 nsCommonMonitorNetworkInterfacesSatIndex	1.3.6.1.4.1.37576.2.2.5.1.2.1.1	Counter32	not-accessible	Network SAT Interfaces status index
IP nsCommonMonitorNetworkInterfacesSatIpAddress	1.3.6.1.4.1.37576.2.2.5.1.2.1.8	IpAddress	read-only	Network SAT Interfaces ip address status
STR nsCommonMonitorNetworkInterfacesSatMacAddress	1.3.6.1.4.1.37576.2.2.5.1.2.1.7	DisplayString	read-only	Network SAT Interfaces mac address status
STR nsCommonMonitorNetworkInterfacesSatName	1.3.6.1.4.1.37576.2.2.5.1.2.1.2	DisplayString	read-only	Network SAT Interfaces status name
INT nsCommonMonitorNetworkInterfacesSatOperStatus	1.3.6.1.4.1.37576.2.2.5.1.2.1.4	INTEGER	read-only	Network SAT Interfaces operational status
U32 nsCommonMonitorNetworkInterfacesSatPid	1.3.6.1.4.1.37576.2.2.5.1.2.1.6	Unsigned32	read-only	Network SAT Interfaces PID status
U32 nsCommonMonitorNetworkInterfacesSatPort	1.3.6.1.4.1.37576.2.2.5.1.2.1.5	Unsigned32	read-only	Network SAT Interfaces port status
IP nsCommonMonitorNetworkInterfacesSatSubnetMask	1.3.6.1.4.1.37576.2.2.5.1.2.1.9	IpAddress	read-only	Network SAT Interfaces subnet mask status
nsCommonMonitorNetworkInterfacesSatTable	1.3.6.1.4.1.37576.2.2.5.1.2		not-accessible	List of interface statuses
nsCommonMonitorNetworkInterfaceStatisticsEntry	1.3.6.1.4.1.37576.2.2.5.2.1		not-accessible	Conceptual row in table for each event.
C32 nsCommonMonitorNetworkInterfaceStatisticsIndex	1.3.6.1.4.1.37576.2.2.5.2.1.1	Counter32	not-accessible	Network InterfaceStatistics interface's index
U32 nsCommonMonitorNetworkInterfaceStatisticsMtu	1.3.6.1.4.1.37576.2.2.5.2.1.2	Unsigned32	not-accessible	Network InterfaceStatistics interface's MTU
STR nsCommonMonitorNetworkInterfaceStatisticsName	1.3.6.1.4.1.37576.2.2.5.2.1.15	DisplayString	read-only	Network Interface Name
NUM nsCommonMonitorNetworkInterfaceStatisticsRxBps	1.3.6.1.4.1.37576.2.2.5.2.1.13	CounterBasedGauge64	read-only	Network Interface Statistics RX Bps
NUM nsCommonMonitorNetworkInterfaceStatisticsRxBytes	1.3.6.1.4.1.37576.2.2.5.2.1.11	CounterBasedGauge64	read-only	Network Interface Statistics RX Bytes
NUM nsCommonMonitorNetworkInterfaceStatisticsRxDrop	1.3.6.1.4.1.37576.2.2.5.2.1.5	CounterBasedGauge64	read-only	Network Interface Statistics RX Drop
NUM nsCommonMonitorNetworkInterfaceStatisticsRxError	1.3.6.1.4.1.37576.2.2.5.2.1.4	CounterBasedGauge64	read-only	Network Interface Statistics RX Errors
NUM nsCommonMonitorNetworkInterfaceStatisticsRxOk	1.3.6.1.4.1.37576.2.2.5.2.1.3	CounterBasedGauge64	read-only	Network Interface Statistics RX OK
NUM nsCommonMonitorNetworkInterfaceStatisticsRxOvr	1.3.6.1.4.1.37576.2.2.5.2.1.6	CounterBasedGauge64	read-only	Network Interface Statistics RX Ovr
nsCommonMonitorNetworkInterfaceStatisticsTable	1.3.6.1.4.1.37576.2.2.5.2		not-accessible	List of interface statuses
NUM nsCommonMonitorNetworkInterfaceStatisticsTxBps	1.3.6.1.4.1.37576.2.2.5.2.1.14	CounterBasedGauge64	read-only	Network Interface Statistics TX Bps
NUM nsCommonMonitorNetworkInterfaceStatisticsTxBytes	1.3.6.1.4.1.37576.2.2.5.2.1.12	CounterBasedGauge64	read-only	Network Interface Statistics TX Bytes
NUM nsCommonMonitorNetworkInterfaceStatisticsTxDrop	1.3.6.1.4.1.37576.2.2.5.2.1.9	CounterBasedGauge64	read-only	Network Interface Statistics TX Drop
NUM nsCommonMonitorNetworkInterfaceStatisticsTxError	1.3.6.1.4.1.37576.2.2.5.2.1.8	CounterBasedGauge64	read-only	Network Interface Statistics TX Errors
NUM nsCommonMonitorNetworkInterfaceStatisticsTxOk	1.3.6.1.4.1.37576.2.2.5.2.1.7	CounterBasedGauge64	read-only	Network Interface Statistics TX OK
NUM nsCommonMonitorNetworkInterfaceStatisticsTxOvr	1.3.6.1.4.1.37576.2.2.5.2.1.10	CounterBasedGauge64	read-only	Network Interface Statistics TX Ovr
C64 nsCommonMonitorNetworkNeighborsStatisticsAverageTxPacketRate	1.3.6.1.4.1.37576.2.2.5.4.1.3	Counter64	read-only	Network Neighbors Statistics average TX packets rate value
C64 nsCommonMonitorNetworkNeighborsStatisticsAverageTxRate	1.3.6.1.4.1.37576.2.2.5.4.1.2	Counter64	read-only	Network Neighbors Statistics average TX rate value
nsCommonMonitorNetworkNeighborsStatisticsEntry	1.3.6.1.4.1.37576.2.2.5.4.1		not-accessible	Conceptual row in table for each event.
C32 nsCommonMonitorNetworkNeighborsStatisticsIndex	1.3.6.1.4.1.37576.2.2.5.4.1.1	Counter32	not-accessible	Network Neighbors Statistics neighbor's index
nsCommonMonitorNetworkNeighborsStatisticsTable	1.3.6.1.4.1.37576.2.2.5.4		not-accessible	List of Neighbors statuses
C64 nsCommonMonitorNetworkNeighborsStatisticsTxBytes	1.3.6.1.4.1.37576.2.2.5.4.1.4	Counter64	read-only	Network Neighbors Statistics TX bytes value
C64 nsCommonMonitorNetworkNeighborsStatisticsTxPackets	1.3.6.1.4.1.37576.2.2.5.4.1.5	Counter64	read-only	Network Neighbors Statistics TX Packets value
C64 nsCommonMonitorNetworkQueuesStatisticsBackloggedBytes	1.3.6.1.4.1.37576.2.2.5.3.1.5	Counter64	read-only	Network Queues Statistics backlogged bytes value
C64 nsCommonMonitorNetworkQueuesStatisticsBackloggedPackets	1.3.6.1.4.1.37576.2.2.5.3.1.6	Counter64	read-only	Network Queues Statistics backlogged packets value
INT nsCommonMonitorNetworkQueuesStatisticsCos	1.3.6.1.4.1.37576.2.2.5.3.1.2	INTEGER	not-accessible	Network Queues Statistics TX Bytes value
C64 nsCommonMonitorNetworkQueuesStatisticsDroppedGreenPackets	1.3.6.1.4.1.37576.2.2.5.3.1.8	Counter64	read-only	Network Queues Statistics dropped yellow packets value
C64 nsCommonMonitorNetworkQueuesStatisticsDroppedYellowPackets	1.3.6.1.4.1.37576.2.2.5.3.1.7	Counter64	read-only	Network Queues Statistics dropped green packets bytes value
C64 nsCommonMonitorNetworkQueuesStatisticsEnqueuedBytesEx	1.3.6.1.4.1.37576.2.2.5.3.1.3	Counter64	read-only	Network Queues Statistics enqueued bytes value
C64 nsCommonMonitorNetworkQueuesStatisticsEnqueuedPackets	1.3.6.1.4.1.37576.2.2.5.3.1.4	Counter64	read-only	Network Queues Statistics enqueued packets value
nsCommonMonitorNetworkQueuesStatisticsEntry	1.3.6.1.4.1.37576.2.2.5.3.1		not-accessible	Conceptual row in table for each event.
C32 nsCommonMonitorNetworkQueuesStatisticsNeighborIndex	1.3.6.1.4.1.37576.2.2.5.3.1.1	Counter32	not-accessible	Network QueuesStatistics neighbor's index
nsCommonMonitorNetworkQueuesStatisticsTable	1.3.6.1.4.1.37576.2.2.5.3		not-accessible	List of interface statuses
nsCommonMonitorNotifications	1.3.6.1.4.1.37576.2.2.0			Common MIB branch that holds all Common notifications.
nsCommonMonitorPowerSupply	1.3.6.1.4.1.37576.2.2.4			Common MIB branch that holds all power supply status.
nsCommonMonitorPowerSupplyEntry	1.3.6.1.4.1.37576.2.2.4.1.1		not-accessible	Conceptual row in table for each event.
C32 nsCommonMonitorPowerSupplyIndex	1.3.6.1.4.1.37576.2.2.4.1.1.1	Counter32	not-accessible	Device Power Supply status index
STR nsCommonMonitorPowerSupplyName	1.3.6.1.4.1.37576.2.2.4.1.1.2	DisplayString	read-only	Name of Power Supply status
nsCommonMonitorPowerSupplyTable	1.3.6.1.4.1.37576.2.2.4.1		not-accessible	List of Events occured
STR nsCommonMonitorPowerSupplyValue	1.3.6.1.4.1.37576.2.2.4.1.1.3	DisplayString	read-only	Value of Power Supply status
nsCommonMonitorVoltage	1.3.6.1.4.1.37576.2.2.3			Common MIB branch that holds all Voltage status.
nsCommonMonitorVoltageEntry	1.3.6.1.4.1.37576.2.2.3.1.1		not-accessible	Conceptual row in table for each event.
C32 nsCommonMonitorVoltageIndex	1.3.6.1.4.1.37576.2.2.3.1.1.1	Counter32	not-accessible	Device voltage status index
STR nsCommonMonitorVoltageName	1.3.6.1.4.1.37576.2.2.3.1.1.2	DisplayString	read-only	Name of voltage status
nsCommonMonitorVoltageTable	1.3.6.1.4.1.37576.2.2.3.1		not-accessible	List of Events occured
I32 nsCommonMonitorVoltageValue	1.3.6.1.4.1.37576.2.2.3.1.1.3	Integer32	read-only	Value of voltage status in mVoltage
nsCommonProducts	1.3.6.1.4.1.37576.2.4			Common MIB branch that holds all Novelsat Products
nsCommonSystem	1.3.6.1.4.1.37576.2.3			Common MIB branch that holds all System status.
nsCommonSystemDatabase	1.3.6.1.4.1.37576.2.3.4			Common MIB branch that holds all Database actions.
INT nsCommonSystemDatabaseCmd	1.3.6.1.4.1.37576.2.3.4.3	INTEGER	read-write	Database command save(1) - save configuration to file load(2) - load and activate configuration delete(3) - delete configuration file default(4) - set current configuration to factory defaults upload (5) - upload database into TFTP server download (6) - download database via TFTP server into the device
STR nsCommonSystemDatabaseCmdDbName	1.3.6.1.4.1.37576.2.3.4.1	DisplayString	read-write	Database file name for database commands
nsCommonSystemDatabaseEntry	1.3.6.1.4.1.37576.2.3.4.4.1		not-accessible	Conceptual row in table for each event.
U32 nsCommonSystemDatabaseID	1.3.6.1.4.1.37576.2.3.4.4.1.1	Unsigned32	not-accessible	Database ID
STR nsCommonSystemDatabaseName	1.3.6.1.4.1.37576.2.3.4.4.1.2	DisplayString	read-only	Database name
IP nsCommonSystemDatabaseServerIP	1.3.6.1.4.1.37576.2.3.4.2	IpAddress	read-write	TFTP Server IP address for database upload/download commands
nsCommonSystemDatabaseTable	1.3.6.1.4.1.37576.2.3.4.4		not-accessible	List of Databases
nsCommonSystemHwConfig	1.3.6.1.4.1.37576.2.3.2			Common MIB branch that holds all Common software Version.
STR nsCommonSystemHwConfigBUCFeeder	1.3.6.1.4.1.37576.2.3.2.7	DisplayString	read-only	Product BUC Feeder configuration
nsCommonSystemHwConfigCardEntry	1.3.6.1.4.1.37576.2.3.2.6.1		not-accessible	Conceptual row in table for each event.
STR nsCommonSystemHwConfigCardHwVersion	1.3.6.1.4.1.37576.2.3.2.6.1.4	DisplayString	read-only	Card hardware version
U32 nsCommonSystemHwConfigCardID	1.3.6.1.4.1.37576.2.3.2.6.1.1	Unsigned32	not-accessible	Card ID
STR nsCommonSystemHwConfigCardSerialNumber	1.3.6.1.4.1.37576.2.3.2.6.1.3	DisplayString	read-only	Card Serial number
STR nsCommonSystemHwConfigCardSwVersion	1.3.6.1.4.1.37576.2.3.2.6.1.5	DisplayString	read-only	Card software version. Only for Gig-E card
nsCommonSystemHwConfigCardTable	1.3.6.1.4.1.37576.2.3.2.6		not-accessible	List of Cards
STR nsCommonSystemHwConfigCardType	1.3.6.1.4.1.37576.2.3.2.6.1.2	DisplayString	read-only	Card type
STR nsCommonSystemHwConfigHardwareVersion	1.3.6.1.4.1.37576.2.3.2.3	DisplayString	read-only	Product hardware number
STR nsCommonSystemHwConfigInternalClockType	1.3.6.1.4.1.37576.2.3.2.5	DisplayString	read-only	Product internal clock type
STR nsCommonSystemHwConfigMacAddress	1.3.6.1.4.1.37576.2.3.2.4	DisplayString	read-only	Product management port MAC address
STR nsCommonSystemHwConfigProductType	1.3.6.1.4.1.37576.2.3.2.1	DisplayString	read-only	Product type
STR nsCommonSystemHwConfigSerialNumber	1.3.6.1.4.1.37576.2.3.2.2	DisplayString	read-only	Product serial number
nsCommonSystemLicense	1.3.6.1.4.1.37576.2.3.5			Common MIB branch that holds License.
I32 nsCommonSystemLicenseFeatureDaysLeft	1.3.6.1.4.1.37576.2.3.5.3.1.4	Integer32	read-only	License feature days left - for temporary license
U32 nsCommonSystemLicenseFeatureIndx	1.3.6.1.4.1.37576.2.3.5.3.1.1	Unsigned32	not-accessible	License feature Index
STR nsCommonSystemLicenseFeatureName	1.3.6.1.4.1.37576.2.3.5.3.1.2	DisplayString	read-only	License feature name
nsCommonSystemLicenseFeaturesEntry	1.3.6.1.4.1.37576.2.3.5.3.1		not-accessible	Conceptual row in table for each license feature.
nsCommonSystemLicenseFeaturesTable	1.3.6.1.4.1.37576.2.3.5.3		not-accessible	List of License features
INT nsCommonSystemLicenseFeatureType	1.3.6.1.4.1.37576.2.3.5.3.1.3	INTEGER	read-only	License feature type
I32 nsCommonSystemLicenseID	1.3.6.1.4.1.37576.2.3.5.2	Integer32	read-only	License ID
STR nsCommonSystemLicenseIssueDate	1.3.6.1.4.1.37576.2.3.5.1	DisplayString	read-only	Issue Date of the License
INT nsCommonSystemSwActivateBackupCmd	1.3.6.1.4.1.37576.2.3.3.8	INTEGER	read-write	Software upgrade command
nsCommonSystemSwUpdate	1.3.6.1.4.1.37576.2.3.3			Common MIB branch that holds all Common software Version.
INT nsCommonSystemSwUpdateCmd	1.3.6.1.4.1.37576.2.3.3.5	INTEGER	read-write	Software upgrade command
INT nsCommonSystemSwUpdateComplete	1.3.6.1.4.1.37576.2.3.3.6	INTEGER	read-only	Software upgrade process complete
STR nsCommonSystemSwUpdateFileName	1.3.6.1.4.1.37576.2.3.3.4	DisplayString	read-write	FTP Server software package file name for software upgrade process
STR nsCommonSystemSwUpdatePassword	1.3.6.1.4.1.37576.2.3.3.3	DisplayString	read-write	FTP Server user password for software upgrade process
IP nsCommonSystemSwUpdateServerIP	1.3.6.1.4.1.37576.2.3.3.1	IpAddress	read-write	FTP Server IP address for software upgrade process
INT nsCommonSystemSwUpdateStatus	1.3.6.1.4.1.37576.2.3.3.7	INTEGER	read-only	Software upgrade process status
STR nsCommonSystemSwUpdateUserName	1.3.6.1.4.1.37576.2.3.3.2	DisplayString	read-write	FTP Server user name for software upgrade process
nsCommonSystemSwVersion	1.3.6.1.4.1.37576.2.3.1			Common MIB branch that holds all Common software Version.
STR nsCommonSystemSwVersionAppCLI	1.3.6.1.4.1.37576.2.3.1.5.1.4	DisplayString	read-only	CLI active version
nsCommonSystemSwVersionAppEntry	1.3.6.1.4.1.37576.2.3.1.5.1		not-accessible	Conceptual row in table for each event.
STR nsCommonSystemSwVersionAppFP	1.3.6.1.4.1.37576.2.3.1.5.1.3	DisplayString	read-only	FP active version
STR nsCommonSystemSwVersionAppNsmd	1.3.6.1.4.1.37576.2.3.1.5.1.5	DisplayString	read-only	NSMD active version
STR nsCommonSystemSwVersionAppPIC	1.3.6.1.4.1.37576.2.3.1.5.1.6	DisplayString	read-only	PIC active version
nsCommonSystemSwVersionAppTable	1.3.6.1.4.1.37576.2.3.1.5		not-accessible	List of software Version
INT nsCommonSystemSwVersionAppType	1.3.6.1.4.1.37576.2.3.1.5.1.1	INTEGER	not-accessible	Card ID
STR nsCommonSystemSwVersionAppWeb	1.3.6.1.4.1.37576.2.3.1.5.1.2	DisplayString	read-only	WEB active version
STR nsCommonSystemSwVersionDb	1.3.6.1.4.1.37576.2.3.1.4	DisplayString	read-only	DB version
STR nsCommonSystemSwVersionFirmware	1.3.6.1.4.1.37576.2.3.1.1	DisplayString	read-only	Firmware version
STR nsCommonSystemSwVersionFs	1.3.6.1.4.1.37576.2.3.1.3	DisplayString	read-only	FS version
STR nsCommonSystemSwVersionOs	1.3.6.1.4.1.37576.2.3.1.2	DisplayString	read-only	OS version
nsNS1000	1.3.6.1.4.1.37576.2.4.1
nsNS2000	1.3.6.1.4.1.37576.2.4.2
nsNS3000	1.3.6.1.4.1.37576.2.4.3

RFC description

Novelsat Common MIB providing configuration parameters for management IP addressing and network connectivity settings.

Start monitoring Novelsat NS1000/NS2000/NS3000 series VSAT satellite modem (shared conventions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NOVELSAT-COMMON-MIB