| OID symbolic | OID numeric | Type | Access | Description |
|---|
| luDload | 1.3.6.1.4.1.677 | | | Lucent Generic Download / Upload Private MIB |
| luOpTable | 1.3.6.1.4.1.677.1 | | not-accessible | |
| luOpEntry | 1.3.6.1.4.1.677.1.1 | | not-accessible | Each entry in the LU Operations Table corresponds to a unique
logical managed device. It is possible that a single HW device
can have resident severial Logical managed devices. |
| OCT luOpSerialNumber | 1.3.6.1.4.1.677.1.1.1 | OCTET STRING | read-only | The identifier of the device. This is a unique number
and in most cases maps directly to the base MAC address
of the device. Otherwise any combination of characters
up to 32 bytes long. |
| OCT luOpMCodeVersion | 1.3.6.1.4.1.677.1.1.2 | OCTET STRING | read-only | Microcode version of the device. Stored in the
format :-
first Byte - not used
2nd Byte - microcode major version number
3rd Byte - microcode minor version number
4th Byte - microcode debug version number. |
| OCT luOpBCodeVersion | 1.3.6.1.4.1.677.1.1.3 | OCTET STRING | read-only | Bootcode version of the device and the hardware
version. Stored in the format :-
first Byte - hardware version number
2nd Byte - microcode major version number
3rd Byte - microcode minor version number
4th Byte - microcode debug version number. |
| STR luOpMCodeFilename | 1.3.6.1.4.1.677.1.1.4 | DisplayString | read-only | Original filename for the microcode that has
been downloaded to the device. |
| INT luOpAdminStatus | 1.3.6.1.4.1.677.1.1.5 | INTEGER | read-write | The desired operating mode of the device. The mode
can be changed by setting this object. If the device
does not support the action it will return a bad
value error. The behaviour of these states is
device specific and some of the states may latch
until the state is returned to normal.
normal - standard operating mode / can be used
to cancel a download or return the
device from any latching state.
reboot - force the device to reboot. The
device will reboot into the version
of flash identified by
luOpDefaultFlashVersion.
identify - force the device to identify itself
by flashing lights. This state may
latch.
test - force the device to do a self test.
This state may latch.
erase-config - erase all configuration info
erase-flash - erase the version of microcode stored
in the flash bank identifed by
luOpEraseFlashVersion.
tftp-ip - force the device to start a TFTP
download over IP
tftp-ipx - force the device to start a TFTP
download over IPX
rpl-ipx - force the device to start a RPL
download over IPX
rpl-llc - force the device to start a RPL
download over LLC
halt - force the defice to shutdown ready
for power off
up-tftp-ip - force the device to start a TFTP
upload over IP
up-tftp-ipx - force the device to start a TFTP
upload over IPX
snapshot - force the device to take a snapshot
of its current configuration and save it to the
name specified by the luOpConfFileName object.
snapshot-tftp - force the device to take a snapshot
of its running configuration and tftp it
to a server.
startup-tftp - force the device to upload it's startup
configuration to a tftp server.
file-tftp - force the device to upload a configuration file
(specified in the luOpConfFileName object )
to a tftp server.
tftp-startup - force the device to download it's startup
configuration from a tftp server.
tftp-snapshot - force the device to download it's running
configuration from a tftp server.
tftp-start-snap - force the device to download it's running
configuration & startup configuration from
a tftp server.
tftp-file - force the device to download a configuration file
from a tftp server.
snapshot-startup - force the device to take a snapshot of it's running
configuration and save it as the startup configuration.
file-snapshot - force the device to copy the file specified in the
luOpConfFileName to it's running configuration
file-startup - force the device to copy the file specified in the
luOpConfFileName to it's startup configuration |
| INT luOpOperStatus | 1.3.6.1.4.1.677.1.1.6 | INTEGER | read-only | The current operating mode of the device.
normal - standard operating mode
reboot - the device is rebooting
identify - the device is identifying itself
test - the device is performing a self-test
downloading - the device is performing a download
uploading - the device is performing an upload
reading-config - the device is reading a configuration file
NOTE:This variable is only available on devices
that support version 1.2 or greater of the Box MIB |
| INT luOpEraseFlashVersion | 1.3.6.1.4.1.677.1.1.7 | INTEGER | read-write | A valid version index for the bank of flash or a
software component to erase when AdminStatus is set
to erase-flash.
NOTE:This variable is only available on devices
that support version 1.2 or greater of the Box MIB |
| INT luOpDefaultFlashVersion | 1.3.6.1.4.1.677.1.1.8 | INTEGER | read-write | The version index of the default flash bank that
a device will reboot into when a standard reboot
is performed.
NOTE:This variable is only available on devices
that support version 1.2 or greater of the Box MIB |
| STR luOpConfFileName | 1.3.6.1.4.1.677.1.1.9 | DisplayString | read-write | This specifies the filename under which to store
the current configuration. |
| INT luOpIndex | 1.3.6.1.4.1.677.1.1.10 | INTEGER | read-only | |
| luDeviceTable | 1.3.6.1.4.1.677.2 | | not-accessible | A table containing information for all
downloadable locations in the device components
in a device. |
| luDeviceEntry | 1.3.6.1.4.1.677.2.1 | | not-accessible | An entry containing information for a
specific downloadable location in a device. |
| INT luDeviceIndex | 1.3.6.1.4.1.677.2.1.1 | INTEGER | not-accessible | Index into the table. Note: To support backwards
compatibility, the following restrictions apply to
the assignment of luDeviceIndex values.
luDeviceIndex value 1 -- flash device Bank A,
luDeviceIndex value 2 -- flash device Bank B |
| STR luDeviceDescription | 1.3.6.1.4.1.677.2.1.2 | DisplayString | read-only | A string containing a textual description for
the component identified by this entry. |
| STR luDeviceLocation | 1.3.6.1.4.1.677.2.1.3 | DisplayString | read-only | A string containing a textual description of the
location of the component identified by this entry.
eg Flash Bank A Flash ROM
Boot ROM Boot Bank A
Base Hardware Hardware Module
NvRam non-Volitile Ram storage |
| OCT luDeviceNumber | 1.3.6.1.4.1.677.2.1.4 | OCTET STRING | read-only | Version number for the component. Stored in the
format :-
1st Byte - major version number
2nd Byte - minor version number
3rd Byte - debug version number. |
| INT luDeviceType | 1.3.6.1.4.1.677.2.1.5 | INTEGER | read-only | The type of object that this table entry contains
Location information for.
flash : code image resident in flash OR the flash
bank itself
boot-fixed : the version of the fixed boot ROM.
boot-updateable : the current version of boot ROM
code where the code can be updated.
hardware-fixed : Hardware that cannot be upgraded.
hardware-upgradeable : a plug in card that can be
changed.
sw_running : code image that is currently running in
RAM.
sw_component : a subcomponent of the entire software.
Can be resident in flash or ram. These items
should be placed in the version table
following the version of which they are a
subcomponent.
default-image: The default image.
non-default-image: Other images.
default-boot-loader: The default boot loader.
non-default-boot-loader: Other boot loaders.
unknown - unknown.
nvram - non-volitile Ram |
| STR luDeviceFileName | 1.3.6.1.4.1.677.2.1.6 | DisplayString | read-write | A string containing the file name of the component
identified by this entry. Allows to rename a file. |
| INT luDeviceCountEx | 1.3.6.1.4.1.677.3 | INTEGER | read-only | The number of entries in the Location table |
| luDownloadTable | 1.3.6.1.4.1.677.4 | | not-accessible | |
| luDownloadEntry | 1.3.6.1.4.1.677.4.1 | | not-accessible | |
| IP luDownloadIPAddress | 1.3.6.1.4.1.677.4.1.1 | IpAddress | read-only | The IP address of the server to use for the
download when using TFTP-IP |
| IP luDownloadIPGateway | 1.3.6.1.4.1.677.4.1.2 | IpAddress | read-write | The IP gateway to be used to access the server.
If this variable is zero then use the default
gateway in luOpIPGateway. |
| OCT luDownloadIPXAddress | 1.3.6.1.4.1.677.4.1.3 | OCTET STRING | read-write | The IPX address of the server to use for the
download when using TFTP-IPX or RPL-IPX.
The format of the address is = 12 bytes. |
| MAC luDownloadNodeAddress | 1.3.6.1.4.1.677.4.1.4 | MacAddress | read-write | The Node address of the server to use for the
download when using RPL-LLC |
| STR luDownloadFileName | 1.3.6.1.4.1.677.4.1.5 | DisplayString | read-write | The filename of the microcode to download. The
maximum length of this string is device specific.
If a string that is too long is written to this
variable BAD VALUE will be returned. |
| INT luDownloadDestination | 1.3.6.1.4.1.677.4.1.6 | INTEGER | read-write | The destination for the download. This will
contain the luDeviceIndex for the download
destination. |
| INT luDownloadState | 1.3.6.1.4.1.677.4.1.7 | INTEGER | read-only | The current state of the download |
| INT luDownloadFailureCode | 1.3.6.1.4.1.677.4.1.8 | INTEGER | read-only | While a download is in progress this will
always be 'no-error'. After a download is complete
this indicates the success or failure of the download.
If it is anything other than 'no-error' then
'luDownloadStatusText' will contain a textual
description of the error. Error codes from 100
upwards are errors returned from a TFTP server.
Errors below this are locally generated.
Configuration files may return errors after download
as a result of reading a config file into the system.
conf-file-gen-err - General (unknown error)
conf-file-parse-error - Reading of config file resulted in
parsing errors.
conf-file-exec-error - Reading of config file resulted in
execution errors. |
| STR luDownloadStatusText | 1.3.6.1.4.1.677.4.1.9 | DisplayString | read-only | A display string describing the status of the
download in progress, or the reason for failure of
the last download.
If FailureCode = no-error then StatusText may be
empty. |
| INT luDownloadSize | 1.3.6.1.4.1.677.4.1.10 | INTEGER | read-only | While a download is in progress this indicates the
number of bytes transferred so far. After the
download is completed this remains at the final
size downloaded. |
| STR luDownloadErrorLogName | 1.3.6.1.4.1.677.4.1.11 | DisplayString | read-write | The filename under which an error log has been created. In
the case of file downloads that produce errors this file should
contain a log of errors that occured |
| INT luDownloadErrorLogLocation | 1.3.6.1.4.1.677.4.1.12 | INTEGER | read-write | The location of the error log. This will
contain the luDeviceIndex for the error log |
| luUploadTable | 1.3.6.1.4.1.677.5 | | not-accessible | |
| luUploadEntry | 1.3.6.1.4.1.677.5.1 | | not-accessible | |
| IP luUploadIPAddress | 1.3.6.1.4.1.677.5.1.1 | IpAddress | read-only | The IP address of the server to use for the
upload when using TFTP-IP |
| IP luUploadIPGateway | 1.3.6.1.4.1.677.5.1.2 | IpAddress | read-write | The IP gateway to be used to access the server.
If this variable is zero then use the default
gateway in luOpIPGateway. |
| OCT luUploadIPXAddress | 1.3.6.1.4.1.677.5.1.3 | OCTET STRING | read-write | The IPX address of the server to use for the
upload when using TFTP-IPX.
The format of the address is = 12 bytes. |
| STR luUploadFileName | 1.3.6.1.4.1.677.5.1.4 | DisplayString | read-write | The filename under which to store the uploaded
microcode. The maximum length of this string is
device specific.
If a string that is too long is written to this
variable BAD VALUE will be returned. |
| INT luUploadSource | 1.3.6.1.4.1.677.5.1.5 | INTEGER | read-write | The source for the upload. This will
contain the luDeviceIndex for the upload
source. |
| INT luUploadState | 1.3.6.1.4.1.677.5.1.6 | INTEGER | read-only | The current state of the Upload |
| INT luUploadFailureCode | 1.3.6.1.4.1.677.5.1.7 | INTEGER | read-only | While an upload is in progress this will
always be 'no-error'. After an upload is complete
this indicates the success or failure of the upload.
If it is anything other than 'no-error' then
'luUploadStatusText' will contain a textual
description of the error. Error codes from 100
upwards are errors returned from a TFTP server.
Errors below this are locally generated.
Configuration files may return errors after / before
upload, as a result of reading a config file into the system.
conf-file-gen-err - General (unknown error)
conf-file-exec-error - Generation of config file resulted in
execution errors. |
| STR luUploadStatusText | 1.3.6.1.4.1.677.5.1.8 | DisplayString | read-only | A display string describing the status of the
upload in progress, or the reason for failure of
the last upload.
If FailureCode = no-error then StatusText may be
empty. |
| INT luUploadSize | 1.3.6.1.4.1.677.5.1.9 | INTEGER | read-only | While an upload is in progress this indicates the
number of bytes transferred so far. After the
upload is completed this remains at the final
size uploaded. |
| STR luUploadErrorLogName | 1.3.6.1.4.1.677.5.1.10 | DisplayString | read-write | The filename under which an error log has been created. In
the case of file uploads that produce errors this file should
contain a log of errors that occured |
| INT luUploadErrorLogLocation | 1.3.6.1.4.1.677.5.1.11 | INTEGER | read-write | The location of the error log. This will
contain the luDeviceIndex for the error log |
| luDloadNotifications | 1.3.6.1.4.1.677.6 | | | |
| INT luNotificationNextIndex | 1.3.6.1.4.1.677.6.1 | INTEGER | read-create | The Next available Index of the
luNotificationDestTable |
| luNotificationDestTable | 1.3.6.1.4.1.677.6.2 | | not-accessible | |
| luNotificationDestEntry | 1.3.6.1.4.1.677.6.2.1 | | not-accessible | |
| INT luNotificationIndex | 1.3.6.1.4.1.677.6.2.1.1 | INTEGER | read-create | The Index of this Destination entry. |
| IP luNotificationIPAddress | 1.3.6.1.4.1.677.6.2.1.2 | IpAddress | read-create | The IP address of the trap receiver. If IPX Addresses
are being used this entry must be zero. |
| IP luNotificationIPGateway | 1.3.6.1.4.1.677.6.2.1.3 | IpAddress | read-create | The IP gateway of the trap receiver. If IPX Addresses
are being used this entry must be zero. |
| OCT luNotificationIPXAddress | 1.3.6.1.4.1.677.6.2.1.4 | OCTET STRING | read-create | The IPX address of the trap receiver. If IP Addresses
are being used this entry must be zero.
The format of the address is = 12 bytes. |
| MAC luNotificationNodeAddress | 1.3.6.1.4.1.677.6.2.1.5 | MacAddress | read-create | The Node address of the trap receiver. If IP Addresses
are being used this entry must be zero. |
| INT luNotificationTrapTypes | 1.3.6.1.4.1.677.6.2.1.6 | INTEGER | read-create | The Trap types this entry should receive. |
| ROW luNotificationRowStatus | 1.3.6.1.4.1.677.6.2.1.7 | RowStatus | read-create | The Status of this entry in the table.
Note the available states:
active(1), -- Obviously Active.
notInService(2) -- Configured but disabled.
notReady(3), -- NOT fully configured.
createAndGo(4),
createAndWait(5)
or destroy(6) |
| NTF luDloadTrapCompleted | 1.3.6.1.4.1.677.6.3 | | | Indicates that a download has completed. |
| NTF luUpLoadTrapCompleted | 1.3.6.1.4.1.677.6.4 | | | Indicates that a upload has completed. |
