All MIBs › Juniper-ATM-1483-Profile-MIB › juniAtm1483ProfileAutoConfLockoutMin
juniAtm1483ProfileAutoConfLockoutMin
Module: Juniper-ATM-1483-Profile-MIB
OID (symbolic): Juniper-ATM-1483-Profile-MIB::juniAtm1483ProfileAutoConfLockoutMin
OID (numeric): 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.4
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: The lower bound, in seconds, of the time range used to specify the duration of the lockout of the encapsulation type from recognition for the specified interface. This only takes effect if juniAtm1483ProfileAutoConfEnable is set to enable for the encapsulation type for this interface. The ability to lockout the specified encapsulation type from recognition in the event of an error in creating an interface of the encapsulation type is enabled by default. The initial lockout duration is this object's value and increases exponentially for each failure that occurs for the specified encapsulation type for the specified interface within the greater of 15 minutes and juniAtm1483ProfileAutoConfLockoutMax. The lockout duration for the specified encapsulation type will not exceed juniAtm1483ProfileAutoConfLockoutMax. If the time between creation errors for the specified encapsulation type for the specified interface is greater than the greater of 15 minutes and juniAtm1483ProfileAutoConfLockoutMax, then the lockout duration reverts to this object's value. To disable the ability to lockout the specified encapsulation type from recognition in the event of an error in creating an interface of the encapsulation type for the specified interface, the value of this object and juniAtm1483ProfileAutoConfLockoutMax must be set to 0. It is not recommended that this lockout feature be disabled except for debugging purposes.
What is juniAtm1483ProfileAutoConfLockoutMin?
The starting lockout duration, in seconds (0-86400, default 1), applied to an encapsulation type after a failed autoconfiguration attempt, before the lockout begins exponentially increasing on repeated failures; setting both this and the Max object to 0 disables the lockout feature entirely. An admin generally leaves this lockout mechanism enabled, only disabling it (both min and max to 0) temporarily for debugging a misbehaving autoconfiguration setup.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.4 snmpwalk -v2c -c public <target> Juniper-ATM-1483-Profile-MIB::juniAtm1483ProfileAutoConfLockoutMin
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.4.1 snmpget -v2c -c public <target> Juniper-ATM-1483-Profile-MIB::juniAtm1483ProfileAutoConfLockoutMin.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.4.1 i <value>
Start monitoring Juniper Networks E-series (JUNOSe) router (ATM RFC 1483/2684 profiles) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the Juniper-ATM-1483-Profile-MIB::juniAtm1483ProfileAutoConfLockoutMin OID value, configure state conditions and alerts, and monitor any Juniper Networks E-series (JUNOSe) router (ATM RFC 1483/2684 profiles) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.4874 | juniperUni | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2 | juniperUniMibs | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2.2 | juniMibs | Juniper-MIBs |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.4874.2.2.58 | juniAtm1483ProfileMIB | Juniper-ATM-1483-Profile-MIB |
| 1.3.6.1.4.1.4874.2.2.58.1 | juniAtm1483ProfileObjects | Juniper-ATM-1483-Profile-MIB |
| 1.3.6.1.4.1.4874.2.2.58.1.1 | juniAtm1483Profile | Juniper-ATM-1483-Profile-MIB |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2 | juniAtm1483ProfileAutoConfTable | Juniper-ATM-1483-Profile-MIB |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1 | juniAtm1483ProfileAutoConfEntry | Juniper-ATM-1483-Profile-MIB |
| 1.3.6.1.4.1.4874.2.2.58.1.1.2.1.4 | juniAtm1483ProfileAutoConfLockoutMin | Juniper-ATM-1483-Profile-MIB |