All MIBs › HPN-ICF-IPSEC-MONITOR-V2-MIB › hpnicfIPsecTunIKETunRemoteIDVal1V2
hpnicfIPsecTunIKETunRemoteIDVal1V2
Module: HPN-ICF-IPSEC-MONITOR-V2-MIB
OID (symbolic): HPN-ICF-IPSEC-MONITOR-V2-MIB::hpnicfIPsecTunIKETunRemoteIDVal1V2
OID (numeric): 1.3.6.1.4.1.11.2.14.11.15.2.126.1.2.1.8
Node type: OBJECT-TYPE
Type: DisplayString
Access: read-only
Description: The value of the remote peer identity for the associated IPsec Phase-1 IKE Tunnel (IKETunRemoteValue1 in the IKETunnelTable).
If the remote peer type is ipv4Addr/ipv6Addr, this is the IP address used to identify the remote peer.
If the remote peer type is ipv4AddrSubnet/ipv6AddrSubnet, this is the subnet address.
If the remote peer type is ipv4AddrRange/ipv6AddrRange, this is the beginning IP address of the range.
If the remote peer type is fqdn/userFqdn, this is the host name used to identify the remote peer.
If the remote peer type is derAsn1Dn, this is the binary DER encoding of an ASN.1 X.500 Distinguished Name [X.501] of the principal whose certificates are being exchanged to establish the SA.
If the remote peer type is derAsn1Gn, this is the binary DER encoding of an ASN.1 X.500 GeneralName [X.509] of the principal whose certificates are being exchanged to establish the SA.
If the remote peer type is keyId, this is an opaque byte stream which may be used to pass vendor-specific information necessary to identify which pre-shared key should be used to authenticate Aggressive mode negotiations.
What is hpnicfIPsecTunIKETunRemoteIDVal1V2?
Reports the primary value of the remote peer's identity for this tunnel's Phase-1 negotiation, whose meaning depends on the remote ID type: an IP address, subnet address, range start, hostname, or certificate-related binary encoding. Administrators read this to see how the far-end peer identified itself when the tunnel was established.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.11.2.14.11.15.2.126.1.2.1.8 snmpwalk -v2c -c public <target> HPN-ICF-IPSEC-MONITOR-V2-MIB::hpnicfIPsecTunIKETunRemoteIDVal1V2
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.11.2.14.11.15.2.126.1.2.1.8.1 snmpget -v2c -c public <target> HPN-ICF-IPSEC-MONITOR-V2-MIB::hpnicfIPsecTunIKETunRemoteIDVal1V2.1
Start monitoring HPE/H3C Comware VPN gateway/firewall (IPsec tunnel stats, v2) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the HPN-ICF-IPSEC-MONITOR-V2-MIB::hpnicfIPsecTunIKETunRemoteIDVal1V2 OID value, configure state conditions and alerts, and monitor any HPE/H3C Comware VPN gateway/firewall (IPsec tunnel stats, v2) from a single console.
OID Breakdown
Upper-level ancestors (12 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.11 | hp | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2 | nm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.14 | icf | CONFIG-MIB |
| 1.3.6.1.4.1.11.2.14.11 | hpicfObjects | CONFIG-MIB |
| 1.3.6.1.4.1.11.2.14.11.15 | hpnicf | HPN-ICF-OID-MIB |
| 1.3.6.1.4.1.11.2.14.11.15.2 | hpnicfCommon | HPN-ICF-OID-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.11.2.14.11.15.2.126 | hpnicfIPsecMonitorV2 | HPN-ICF-IPSEC-MONITOR-V2-MIB |
| 1.3.6.1.4.1.11.2.14.11.15.2.126.1 | hpnicfIPsecObjectsV2 | HPN-ICF-IPSEC-MONITOR-V2-MIB |
| 1.3.6.1.4.1.11.2.14.11.15.2.126.1.2 | hpnicfIPsecTunnelV2Table | HPN-ICF-IPSEC-MONITOR-V2-MIB |
| 1.3.6.1.4.1.11.2.14.11.15.2.126.1.2.1 | hpnicfIPsecTunnelV2Entry | HPN-ICF-IPSEC-MONITOR-V2-MIB |
| 1.3.6.1.4.1.11.2.14.11.15.2.126.1.2.1.8 | hpnicfIPsecTunIKETunRemoteIDVal1V2 | HPN-ICF-IPSEC-MONITOR-V2-MIB |