| OID symbolic | OID numeric | Type | Access | Description |
|---|
| foreDsx3Mib | 1.3.6.1.4.1.326.2.2.1.1.15 | | | This mib module implements extensions to the standard DS3
mib to support extra configuration, statistics, and
diagnostic capabilities of Fore Systems equipment. |
| NTF foreDsx3LOFDetected | 1.3.6.1.4.1.326.2.2.1.1.15.0.1 | | | This trap indicates that Loss Of Frame(LOF) is detected on
the incoming signal. |
| NTF foreDsx3LOFCleared | 1.3.6.1.4.1.326.2.2.1.1.15.0.2 | | | This trap indicates that Loss Of Frame is cleared on
the incoming signal. |
| NTF foreDsx3AISDetected | 1.3.6.1.4.1.326.2.2.1.1.15.0.3 | | | This trap indicates that AIS Alarm is detected on
the incoming signal. |
| NTF foreDsx3AISCleared | 1.3.6.1.4.1.326.2.2.1.1.15.0.4 | | | This trap indicates that AIS Alarm is cleared on
the incoming signal. |
| NTF foreDsx3FERFDetected | 1.3.6.1.4.1.326.2.2.1.1.15.0.5 | | | This trap indicates that FERF Alarm or DS3 Yellow Alarm
is detected on the incoming signal. |
| NTF foreDsx3FERFCleared | 1.3.6.1.4.1.326.2.2.1.1.15.0.6 | | | This trap indicates that FERF Alarm or DS3 Yellow Alarm
is cleared on the incoming signal. |
| NTF foreDsx3LOSDetected | 1.3.6.1.4.1.326.2.2.1.1.15.0.7 | | | This trap indicates that the specified DS3 port has
detected incoming LOS Alarm. |
| NTF foreDsx3LOSCleared | 1.3.6.1.4.1.326.2.2.1.1.15.0.8 | | | This trap indicates that the incoming LOS Alarm has been
cleared on the specified DS3 port. |
| NTF foreDsx3IdleDetected | 1.3.6.1.4.1.326.2.2.1.1.15.0.9 | | | This trap indicates that an Idle Maintenance Signal
(IDLE) is detected on the incoming signal. |
| NTF foreDsx3IdleCleared | 1.3.6.1.4.1.326.2.2.1.1.15.0.10 | | | This trap indicates that an Idle Maintenance Signal
(IDLE) is cleared on the incoming signal. |
| NTF foreDsx3TrailChangeDetected | 1.3.6.1.4.1.326.2.2.1.1.15.0.11 | | | This trap indicates that a Trail Trace Mismatch
was detected on the incoming signal. |
| NTF foreDsx3PbitPerrDetected | 1.3.6.1.4.1.326.2.2.1.1.15.0.12 | | | This trap indicates that the specified DSX3 port is
experiencing P-bit Parity errors. A P-bit Parity Error
failure is declared when the P-bit Parity Error
persists for a period of 2.5 +/- 0.5 seconds. |
| NTF foreDsx3PbitPerrCleared | 1.3.6.1.4.1.326.2.2.1.1.15.0.13 | | | This trap indicates that the P-bit Parity Error failure
identified by trap asxDS3PbitPerrDetected has been cleared.
A P-bit Parity Error failure is cleared when the P-bit Parity
Error defect is absent for 10 +/- 0.5 seconds. |
| foreDsx3ConfigTable | 1.3.6.1.4.1.326.2.2.1.1.15.1 | | not-accessible | A table of configuration options, statistics, and
diagnostics supported by DS3 interfaces on
Fore Systems ATM Switches. |
| foreDsx3ConfigEntry | 1.3.6.1.4.1.326.2.2.1.1.15.1.1 | | not-accessible | A table entry containing Fore specific extensions
to the standard DS3 MIB tables. |
| INT foreDsx3ConfigReceiveCode | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.1 | INTEGER | read-only | This variable indicates the type of code that was received
across the DS3/E3 interface.
The values mean:
ds3ReceiveNoCode receiving looped or normal data
ds3ReceiveLineCode receiving request for a line loopback
ds3ReceivePayloadCode receiving a request for a payload loopback
(i.e. all DS1/E1 in a DS3/E3 frame)
ds3ReceiveResetCode receiving a loopback deactivation request
ds3ReceiveDS1LoopCode receiving a request to loopback a particular
DS1/E1 within a DS3/E3 frame
ds3ReceiveTestPattern receiving a test pattern. |
| INT foreDsx3ConfigLineLength | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.2 | INTEGER | read-write | This variable represents the length of the physical cable
connected to the ds3 port. The user has to set this object to
match the physical cable in order to get the netmod to receive
the signal on the cable. The different values are: ds3LineLt225
(1) means the line is shorter than 225 ft, ds1LineGt225 (2)
means the line length is greater than 220 ft. This value is not
settable for Series A netmods and the value for these netmods
is Gt225 |
| I32 foreDsx3ConfigStatus | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.3 | Integer32 | read-only | This variable represents the current status of the Dsx3
interface. This variable is a bit map represented as
a sum.
The various bit positions are:
1 dsx3NoDefect True if no other defects are present
2 dsx3RxFERF Receiving a Far End Receive Failure
4 dsx3TxFERF Sending a Far End Receive Failure
8 dsx3RxAIS Receiving Alarm Indication
16 dsx3TxAIS Transmitting Alarm Indication
32 dsx3LOF Loss Of Frame
64 dsx3LOS Loss Of Signal
128 dsx3Loopback Remotly Initiatiated Loopback Operational
256 dsx3RxTest Receiving Test Pattern
512 dsx3Other Other, non specific falure. |
| INT foreDsx3LineTypeFraming | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.4 | INTEGER | read-only | This variable extends the 'dsx3LineType' variable from
rfc1407. When dsx3LineType == e3Framed, this variable
determines whether G.751 or G.832 framing is used.
When dsx3LineType == e3Plcp, the value of this variable
will be 1, indicating G.751 framing. |
| I32 foreDsx3PbitPerrThrSeconds | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.5 | Integer32 | read-write | This variable represents the consecutive number of
BAD/GOOD seconds to detect/clear an Excessive P-bit
Parity Error Defect. The range of values it can take
is between 2 and 10 inclusive. |
| I32 foreDsx3PbitPerrThrErrors | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.6 | Integer32 | read-write | This variable is a threshold for the number of P-bit
Parity Errors per second and is used as a parameter to
the Excessive P-bit Parity Error Defect. If the number
of errors exceeds the threshold, the particular second is
declared BAD, otherwise it is declared GOOD. |
| INT foreDsx3PbitPerrFailEnable | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.7 | INTEGER | read-write | This variable controls whether declaration of an
Excessive P-bit Parity Error Defect forces the port's
operState to Down. |
| I32 foreDsx3SignalDegradeBer | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.8 | Integer32 | read-write | This is the exponent of 10 for the current signal
degrade bit error rate (BER) threshold for this port.
The value -7, for example, represents a BER of 1E-7.
This variable is only applicable when dsx3BerErrorModel
is set to errorModelRandom. |
| I32 foreDsx3SignalFailBer | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.9 | Integer32 | read-write | This is the exponent of 10 for the current signal
fail bit error rate (BER) threshold for this port.
The value -4, for example, represents a BER of 1E-4.
This variable is only applicable when dsx3BerErrorModel
is set to errorModelRandom. |
| INT foreDsx3BerErrorModel | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.10 | INTEGER | read-write | This is the error distribution model to be used to
identify signal degrade and signal fail conditions.
errorModelRandom selects a random error distribution
and declares signal conditions based on the thresholds
set in dsx3SignalDegradeBer and dsx3SignalFailBer.
errorModelBurst selects a burst error model and declares
signal degrade conditions based on the thresholds set in
dsx3BipThrSeconds and dsx3BipThrErrors. errorModelNone
disables detection of signal conditions. |
| INT foreDsx3BerState | 1.3.6.1.4.1.326.2.2.1.1.15.1.1.11 | INTEGER | read-only | This value describes the current state of the port as
determined through bit error rate analysis. |
| foreDsx3TotalTable | 1.3.6.1.4.1.326.2.2.1.1.15.2 | | not-accessible | A table of statistics, supported by DS3 interfaces on
Fore Systems Equipment. |
| foreDsx3TotalEntry | 1.3.6.1.4.1.326.2.2.1.1.15.2.1 | | not-accessible | A table entry containing Fore specific extensions
to the standard DS3 MIB tables. |
| C32 foreDsx3TotalFramingLOSsEx | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.1 | Counter32 | read-only | The number of seconds in which Loss Of Signal (LOS) errors
were detected by the DS3 Receive Framer block. |
| C32 foreDsx3TotalFramingLCVs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.2 | Counter32 | read-only | The number of Line Code Violations (LCV) that were detected by
the DS3 Receive Framer block. |
| C32 foreDsx3TotalFramingSumLCVs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.3 | Counter32 | read-only | The number of DS3 information blocks (85 bits) which contain
one or more Line Code Violations (LCV). |
| C32 foreDsx3TotalFramingFERRs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.4 | Counter32 | read-only | Number of DS3 framing error (FERR) events. |
| C32 foreDsx3TotalFramingOOFs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.5 | Counter32 | read-only | Number of seconds DS3 Out Of Frame (OOF) error events were
experienced. |
| C32 foreDsx3TotalFramingFERFs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.6 | Counter32 | read-only | The number of seconds in which Far End Receive Failure (FERF)
state has been detected by the DS3 Receive Framer block. FERF
signal alerts the upstream terminal that a failure has been
detected along the downstream line. |
| C32 foreDsx3TotalFramingAISs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.7 | Counter32 | read-only | The number of seconds in which Alarm Indication Signals (AIS)
were detected by the DS3 Receive Framer block. AIS indicates
that an upstream failure has been detected by the far end. |
| C32 foreDsx3TotalFramingPbitPERRs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.8 | Counter32 | read-only | Number of P-bit parity error (PERR) events or the
number of BIP-8 errors in case of E3 G.832. |
| C32 foreDsx3TotalFramingCbitPERRs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.9 | Counter32 | read-only | Number of C-bit parity error (PERR) events. |
| C32 foreDsx3TotalFramingFEBEs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.10 | Counter32 | read-only | Number of DS3 far end block error (FEBE) events. |
| C32 foreDsx3TotalFramingIDLEs | 1.3.6.1.4.1.326.2.2.1.1.15.2.1.11 | Counter32 | read-only | The number of seconds in which IDLE signal
was detected by the DS3 Receive Framer block. |
