DVB-MGTR101290-MIB

All MIBs › DVB-MGTR101290-MIB

Organization: DVB

Last Updated: 2001-11-07

Category: Domain: CATV/Cable, Domain: Video/Broadcast

Description: Monitors DVB MPEG transport stream quality metrics per ETSI TR 101 290 priority levels for broadcast headends.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DVB-MGTR101290-MIB?

This vendor-neutral DVB Measurement Group MIB implements the MPEG transport-stream quality measurements defined by ETSI TR 101 290, organized into its three standard priority levels. It exposes transport-stream error and quality counters corresponding to sync/PAT/PMT-type critical faults (priority 1) as well as lower-priority quality metrics. It is squarely a software/stream-health monitoring module: priority-1 errors indicate critical decoding failures such as loss of sync, while lower-priority counters flag less severe quality degradation, letting broadcast engineers triage transport-stream health at a glance. It complements DVB-MGSIGNALCHARACTERISTICS-MIB and directly implements the ETSI TR 101 290 test specification. It is typically deployed on transport-stream analyzers and monitoring probes at DVB broadcast headends. Engineers implementing or auditing this functionality typically reference the DVB-MGTR101290-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in DVB-MGTR101290-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral, standards-based MIB, not tied to a specific manufacturer
DVB transport-stream analyzer/monitoring probe

Monitoring Examples

No sample objects were supplied for this module, so specific table names cannot be cited with confidence. Conceptually, an engineer would poll priority-1 error counters to catch critical faults like transport-stream sync loss immediately, while trending priority-2 and priority-3 counters over time to catch slowly developing quality problems. A spike in priority-1 errors would typically indicate an imminent viewer-facing outage.

What Can Be Monitored

TR 101 290 priority-1 critical transport stream errors
priority-2 quality errors
priority-3 monitoring parameters
transport stream sync status

Imported Objects

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using tsTestsSummaryCounter OID:

Select a DVB transport-stream analyzer/monitoring probe (vendor-neutral ETSI TR 101 290 standard) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tsTestsSummaryCounter into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the count of the number of times this error has occurred. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ACT aiCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 aiCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT aiCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F aiCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA aiCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
aiCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.5.1		not-accessible	Row specification
INP aiCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT aiCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA aiCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.9	MeasurementState	read-only	Indicates the validity of the measurement
aiCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.5		not-accessible	Amplitude Imbalance (AI) measurement
TES aiCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.2	TestState	read-only	This indicates whether the aiCSValue is currently within the thresholds.
NUM aiCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.5.1.10	FloatingPoint	read-only	The current Amplitude Imbalance as a percentage
ACT aiTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 aiTCounter	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT aiTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F aiTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA aiTEnable	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
aiTEntry	1.3.6.1.4.1.2696.3.2.1.9.18.5.1		not-accessible	Row specification
INP aiTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT aiTLatestError	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA aiTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
aiTTable	1.3.6.1.4.1.2696.3.2.1.9.18.5		not-accessible	Amplitude Imbalance (AI) measurement
TES aiTTestState	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.2	TestState	read-only	This indicates whether aiTValue is currently within the thresholds.
NUM aiTValue	1.3.6.1.4.1.2696.3.2.1.9.18.5.1.10	FloatingPoint	read-only	The current Amplitude Imbalance as a percentage
berRS	1.3.6.1.4.1.2696.3.2.1.9.16
ACT berRSActiveTime	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 berRSCounter	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT berRSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F berRSCounterReset	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA berRSEnable	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
berRSEntry	1.3.6.1.4.1.2696.3.2.1.9.16.1.1		not-accessible	Row specification
INP berRSInputNumber	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
ACT berRSinServiceActiveTime	1.3.6.1.4.1.2696.3.2.1.6.3.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 berRSinServiceCounter	1.3.6.1.4.1.2696.3.2.1.6.3.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT berRSinServiceCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.3.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the berRSinServiceCounter object.
T/F berRSinServiceCounterReset	1.3.6.1.4.1.2696.3.2.1.6.3.1.6	TruthValue	read-write	berRSinServiceCounter is reset to zero and berRSinServiceCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA berRSinServiceEnable	1.3.6.1.4.1.2696.3.2.1.6.3.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
berRSinServiceEntry	1.3.6.1.4.1.2696.3.2.1.6.3.1		not-accessible	Row specification
INP berRSinServiceInputNumber	1.3.6.1.4.1.2696.3.2.1.6.3.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT berRSinServiceLatestError	1.3.6.1.4.1.2696.3.2.1.6.3.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA berRSinServiceMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.3.1.9	MeasurementState	read-only	Indicates the validity of the measurement
berRSinServiceTable	1.3.6.1.4.1.2696.3.2.1.6.3		not-accessible	Measurement of BER before RS decoder
TES berRSinServiceTestState	1.3.6.1.4.1.2696.3.2.1.6.3.1.2	TestState	read-only	This indicates whether the berRSinServiceValue is below the maximum.
NUM berRSinServiceValue	1.3.6.1.4.1.2696.3.2.1.6.3.1.10	FloatingPoint	read-only	This is the current BER as a numeric value, for example 0.0000023
DAT berRSLatestError	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
ACT berRSLPActiveTime	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 berRSLPCounter	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT berRSLPCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F berRSLPCounterReset	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA berRSLPEnable	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
berRSLPEntry	1.3.6.1.4.1.2696.3.2.1.9.16.2.1		not-accessible	Row specification
INP berRSLPInputNumber	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT berRSLPLatestError	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA berRSLPMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
berRSLPTable	1.3.6.1.4.1.2696.3.2.1.9.16.2		not-accessible	BER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'.
TES berRSLPTestState	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.2	TestState	read-only	This indicates whether berRSLPValue is within the thresholds.
NUM berRSLPValue	1.3.6.1.4.1.2696.3.2.1.9.16.2.1.10	FloatingPoint	read-only	This is the BER before RS (outer) decoder for the low priority stream measured using the in-service method. It is expressed as a number, e.g. 0.0000034
MEA berRSMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
berRSTable	1.3.6.1.4.1.2696.3.2.1.9.16.1		not-accessible	BER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream.
TES berRSTestState	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.2	TestState	read-only	This indicates whether berRSValue is below the maximum.
NUM berRSValue	1.3.6.1.4.1.2696.3.2.1.9.16.1.1.10	FloatingPoint	read-only	This is the BER before RS (outer) decoder measured using the in-service method. It is expressed as a number, e.g. 0.0000034
ACT berViterbiSActiveTime	1.3.6.1.4.1.2696.3.2.1.8.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 berViterbiSCounter	1.3.6.1.4.1.2696.3.2.1.8.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT berViterbiSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.8.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the berViterbiSCounter object.
T/F berViterbiSCounterReset	1.3.6.1.4.1.2696.3.2.1.8.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA berViterbiSEnable	1.3.6.1.4.1.2696.3.2.1.8.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
berViterbiSEntry	1.3.6.1.4.1.2696.3.2.1.8.1.1		not-accessible	Row description
INP berViterbiSInputNumber	1.3.6.1.4.1.2696.3.2.1.8.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
NUM berViterbiSIValue	1.3.6.1.4.1.2696.3.2.1.8.1.1.10	FloatingPoint	read-only	This is the pre-Viterbi I path BER value, for example 0.0000023
DAT berViterbiSLatestError	1.3.6.1.4.1.2696.3.2.1.8.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
BER berViterbiSMeasurementMethod	1.3.6.1.4.1.2696.3.2.1.8.1.1.12	BERMeasurementMethod	read-only	This indicates whether the measurement was made separately for the I and Q parts of the signal or by a measurement of I and Q combined.
MEA berViterbiSMeasurementState	1.3.6.1.4.1.2696.3.2.1.8.1.1.9	MeasurementState	read-only	Indicates the validity of the measurement
NUM berViterbiSQValue	1.3.6.1.4.1.2696.3.2.1.8.1.1.11	FloatingPoint	read-only	This is the pre-Viterbi Q path BER value, for example 0.0000023
berViterbiSTable	1.3.6.1.4.1.2696.3.2.1.8.1		not-accessible	BER before Viterbi decoding measurement
TES berViterbiSTestState	1.3.6.1.4.1.2696.3.2.1.8.1.1.2	TestState	read-only	This test fails if either berViterbiSIValue or berViterbiSQValue exceeds the threshold set by satellitePrefBERMax.
berViterbiT	1.3.6.1.4.1.2696.3.2.1.9.15
ACT berViterbiTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 berViterbiTCounter	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT berViterbiTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F berViterbiTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA berViterbiTEnable	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
berViterbiTEntry	1.3.6.1.4.1.2696.3.2.1.9.15.1.1		not-accessible	Row specification
INP berViterbiTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT berViterbiTLatestError	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
ACT berViterbiTLPActiveTime	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 berViterbiTLPCounter	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT berViterbiTLPCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F berViterbiTLPCounterReset	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA berViterbiTLPEnable	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
berViterbiTLPEntry	1.3.6.1.4.1.2696.3.2.1.9.15.2.1		not-accessible	Row specification
INP berViterbiTLPInputNumber	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT berViterbiTLPLatestError	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA berViterbiTLPMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
berViterbiTLPTable	1.3.6.1.4.1.2696.3.2.1.9.15.2		not-accessible	BER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'.
TES berViterbiTLPTestState	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.2	TestState	read-only	This indicates whether the berViterbiTLPValue is within the thresholds.
NUM berViterbiTLPValue	1.3.6.1.4.1.2696.3.2.1.9.15.2.1.10	FloatingPoint	read-only	This is the overall pre-Viterbi BER value, for example 0.0000046
MEA berViterbiTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
berViterbiTTable	1.3.6.1.4.1.2696.3.2.1.9.15.1		not-accessible	BER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream.
TES berViterbiTTestState	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.2	TestState	read-only	This indicates whether the berViterbiTValue is within the thresholds.
NUM berViterbiTValue	1.3.6.1.4.1.2696.3.2.1.9.15.1.1.10	FloatingPoint	read-only	This is the overall pre-Viterbi BER value, for example 0.0000046
bitRate	1.3.6.1.4.1.2696.3.2.1.5.4.2
NUM cablePrefENDBER	1.3.6.1.4.1.2696.3.2.1.7.100.1.6	FloatingPoint	read-write	BER value which is to be used for the END measurement.
T/F cablePrefENDCtoNSpecified	1.3.6.1.4.1.2696.3.2.1.7.100.1.7	TruthValue	read-write	This determines whether cablePrefENDIdeal is expressed as a C/N ratio (value is true) or an Eb/No ratio (value is false).
NUM cablePrefENDIdeal	1.3.6.1.4.1.2696.3.2.1.7.100.1.8	FloatingPoint	read-write	This is the 'ideal' value of C/N or Eb/No for the given BER.
NUM cablePrefENDMax	1.3.6.1.4.1.2696.3.2.1.7.100.1.9	FloatingPoint	read-write	If the measured END exceeds this value the associated test fails.
cablePreferencesEntry	1.3.6.1.4.1.2696.3.2.1.7.100.1		not-accessible	Row specification
cablePreferencesTable	1.3.6.1.4.1.2696.3.2.1.7.100		not-accessible	Table containing per input preferences for cable measurements.
NUM cablePrefEstNoiseMarginMin	1.3.6.1.4.1.2696.3.2.1.7.100.1.3	FloatingPoint	read-write	If the measured estNoiseMarginValue is less than this value the associated test fails.
INP cablePrefInputNumber	1.3.6.1.4.1.2696.3.2.1.7.100.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
NUM cablePrefNoiseMarginMin	1.3.6.1.4.1.2696.3.2.1.7.100.1.2	FloatingPoint	read-write	If the measured noiseMarginValue is less than this value the associated test fails.
NUM cablePrefSignQualBoxSize	1.3.6.1.4.1.2696.3.2.1.7.100.1.4	FloatingPoint	read-write	This object determines the size of the quality threshold box for the signal quality margin test. The quality threshold box is assumed to be square. The value is the ratio of the length of one side of a threshold box to the length of one side of the IQ decision boundary box. An example value is '0.5'.
I32 cablePrefSignQualPercentMax	1.3.6.1.4.1.2696.3.2.1.7.100.1.5	Integer32	read-write	This object sets the limit on how many constellation points may fall outside the threshold box before the signal quality margin test fails. The value is expressed as a percentage, for example '7.5'.
NUM cableSatPrefAiCSMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.26	FloatingPoint	read-write	If aiCSValue exceeds this value, the associated test fails.
NUM cableSatPrefBERMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.18	FloatingPoint	read-write	If the berRSinServiceValue exceeds this value, the associated test fails.
NUM cableSatPrefCentreFrequency	1.3.6.1.4.1.2696.3.2.1.6.100.1.2	FloatingPoint	read-write	This is the centre frequency to which the measuring equipment is tuned for making cable and satellite measurements. This frequency is the actual input frequency to the measuring equipment, which may be at an intermediate frequency (IF) rather than the final RF. This setting affects the objects in the 'tr101290Cable' and 'tr101290Satellite' branches of the MIB as well as the 'tr101290CableSat' branch.
NUM cableSatPrefCiCSMin	1.3.6.1.4.1.2696.3.2.1.6.100.1.29	FloatingPoint	read-write	If ciCSValue is less than this value, the associated test fails.
NUM cableSatPrefCsCSMin	1.3.6.1.4.1.2696.3.2.1.6.100.1.25	FloatingPoint	read-write	If the csCSValue is less than this value, the associated test fails
cableSatPreferencesEntry	1.3.6.1.4.1.2696.3.2.1.6.100.1		not-accessible	Row specification
cableSatPreferencesTable	1.3.6.1.4.1.2696.3.2.1.6.100		not-accessible	Table containing per input configuration information for cable and satellite common measurements.
INP cableSatPrefInputNumber	1.3.6.1.4.1.2696.3.2.1.6.100.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
U32 cableSatPrefLinkAvailM	1.3.6.1.4.1.2696.3.2.1.6.100.1.14	Unsigned32	read-write	The M value used to identify the start and end of a period of Link Unavailable Time (LUAT).
U32 cableSatPrefLinkAvailN	1.3.6.1.4.1.2696.3.2.1.6.100.1.12	Unsigned32	read-write	The N value used to identify the start and end of a period of Link Unavailable Time (LUAT).
NUM cableSatPrefLinkAvailT	1.3.6.1.4.1.2696.3.2.1.6.100.1.13	FloatingPoint	read-write	The T value used to identify the start and end of a period of Link Unavailable Time (LUAT).
NUM cableSatPrefLinkAvailTI	1.3.6.1.4.1.2696.3.2.1.6.100.1.15	FloatingPoint	read-write	Each Time Interval of this length is assessed as to whether it is a Severely Uncorrectable Time Interval (SUTI).
NUM cableSatPrefLinkAvailTotalTime	1.3.6.1.4.1.2696.3.2.1.6.100.1.17	FloatingPoint	read-write	The Total Time over which the Link Availability is calculated.
UAT cableSatPrefLinkAvailUATMode	1.3.6.1.4.1.2696.3.2.1.6.100.1.11	UATMode	read-write	Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Link Unavailable Time (LUAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored.
NUM cableSatPrefLinkAvailUPPerCent	1.3.6.1.4.1.2696.3.2.1.6.100.1.16	FloatingPoint	read-write	If more than this percentage of packets within a Time Interval is an Uncorrectable Packet (UP), the Time Interval is a Severely Uncorrectable Time Interval (SUTI). Example values are: '1.53', '10', '0.33'.
NUM cableSatPrefMerCSMin	1.3.6.1.4.1.2696.3.2.1.6.100.1.22	FloatingPoint	read-write	If the merCSValue is less than this value, the associated test fails.
MOD cableSatPrefModulation	1.3.6.1.4.1.2696.3.2.1.6.100.1.3	Modulation	read-write	This is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to cable and satellite measurements. This setting affects the objects in the 'tr101290Cable' and 'tr101290Satellite' branches of the MIB as well as the 'tr101290CableSat' branch.
NUM cableSatPrefNoisePowerMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.21	FloatingPoint	read-write	If the noise power measured by noisePowerValue exceeds this value, the associated test fails.
NUM cableSatPrefPjCSMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.30	FloatingPoint	read-write	If pjCSValue exceeds this value, the associated test fails.
NUM cableSatPrefQeCSMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.27	FloatingPoint	read-write	If qeCSValue exceeds this value, the associated test fails.
NUM cableSatPrefRteCSMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.28	FloatingPoint	read-write	If rteCSValue exceeds this value, the associated test fails.
NUM cableSatPrefSignalPowerMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.20	FloatingPoint	read-write	If the power measured by rfIFsignalPowerValue is greater than this value, the associated test fails.
NUM cableSatPrefSignalPowerMin	1.3.6.1.4.1.2696.3.2.1.6.100.1.19	FloatingPoint	read-write	If the power measured by rfIFsignalPowerValue is less than this value, the associated test fails.
NUM cableSatPrefSnrCSMin	1.3.6.1.4.1.2696.3.2.1.6.100.1.31	FloatingPoint	read-write	If snrCSValue is less than this value, the associated test fails.
NUM cableSatPrefSteDeviationCSMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.24	FloatingPoint	read-write	If the steDeviationCSValue exceeds this value, the associated test fails.
NUM cableSatPrefSteMeanCSMax	1.3.6.1.4.1.2696.3.2.1.6.100.1.23	FloatingPoint	read-write	If the steMeanCSValue exceeds this value, the associated test fails.
NUM cableSatPrefSysAvailEBPerCent	1.3.6.1.4.1.2696.3.2.1.6.100.1.9	FloatingPoint	read-write	If more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values are: '1.53', '10', '0.33'.
U32 cableSatPrefSysAvailM	1.3.6.1.4.1.2696.3.2.1.6.100.1.7	Unsigned32	read-write	The M value used to identify the start and end of a period of unavailable time (UAT).
U32 cableSatPrefSysAvailN	1.3.6.1.4.1.2696.3.2.1.6.100.1.5	Unsigned32	read-write	The N value used to identify the start and end of a period of unavailable time (UAT).
NUM cableSatPrefSysAvailT	1.3.6.1.4.1.2696.3.2.1.6.100.1.6	FloatingPoint	read-write	The T value used to identify the start and end of a period of unavailable time (UAT).
NUM cableSatPrefSysAvailTI	1.3.6.1.4.1.2696.3.2.1.6.100.1.8	FloatingPoint	read-write	Each Time Interval of this length is assessed as to whether it is a Severely Errored Time Interval.
NUM cableSatPrefSysAvailTotalTime	1.3.6.1.4.1.2696.3.2.1.6.100.1.10	FloatingPoint	read-write	The Total Time over which the System Availability is calculated.
UAT cableSatPrefSysAvailUATMode	1.3.6.1.4.1.2696.3.2.1.6.100.1.4	UATMode	read-write	Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored.
capabilityCable	1.3.6.1.4.1.2696.3.2.1.3.7
AVA capabilityCableAvailability	1.3.6.1.4.1.2696.3.2.1.3.7.2.1.2	Availability	read-only	The availability of a specific test or measurement
capabilityCableEntry	1.3.6.1.4.1.2696.3.2.1.3.7.2.1		not-accessible	Row specification
GRO capabilityCableGroup	1.3.6.1.4.1.2696.3.2.1.3.7.1	GroupAvailability	read-only	Specifies the overall availability of the cable group of tests and measurements, tr101290Cable.
OID capabilityCableOID	1.3.6.1.4.1.2696.3.2.1.3.7.2.1.1	OBJECT IDENTIFIER	not-accessible	The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB.
NUM capabilityCablePollInterval	1.3.6.1.4.1.2696.3.2.1.3.7.2.1.3	PollingInterval	read-only	Indicates the interval between updates of the information supplied by this object.
capabilityCableSat	1.3.6.1.4.1.2696.3.2.1.3.6
AVA capabilityCableSatAvailability	1.3.6.1.4.1.2696.3.2.1.3.6.2.1.2	Availability	read-only	The availability of a specific test or measurement
capabilityCableSatEntry	1.3.6.1.4.1.2696.3.2.1.3.6.2.1		not-accessible	Row specification
GRO capabilityCableSatGroup	1.3.6.1.4.1.2696.3.2.1.3.6.1	GroupAvailability	read-only	Specifies the overall availability of the cable and satellite group of tests and measurements, tr101290CableSat.
OID capabilityCableSatOID	1.3.6.1.4.1.2696.3.2.1.3.6.2.1.1	OBJECT IDENTIFIER	not-accessible	The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB.
NUM capabilityCableSatPollInterval	1.3.6.1.4.1.2696.3.2.1.3.6.2.1.3	PollingInterval	read-only	Indicates the interval between updates of the information supplied by this object.
capabilityCableSatTable	1.3.6.1.4.1.2696.3.2.1.3.6.2		not-accessible	Specifies the individual availability of the cable and satellite group of tests and measurements, tr101290CableSat.
capabilityCableTable	1.3.6.1.4.1.2696.3.2.1.3.7.2		not-accessible	Specifies the individual availability of the cable group of tests and measurements, tr101290Cable.
DAT capabilityMIBRevision	1.3.6.1.4.1.2696.3.2.1.3.1	DateAndTime	read-only	The capabilities of the agent are expressed in relation to a specific revision of the tr101290 MIB module. The date and time here must exactly match one of the revision dates in the MODULE-IDENTITY section of the MIB.
capabilitySatellite	1.3.6.1.4.1.2696.3.2.1.3.8
AVA capabilitySatelliteAvailability	1.3.6.1.4.1.2696.3.2.1.3.8.2.1.2	Availability	read-only	The availability of a specific test or measurement
capabilitySatelliteEntry	1.3.6.1.4.1.2696.3.2.1.3.8.2.1		not-accessible	Row specification
GRO capabilitySatelliteGroup	1.3.6.1.4.1.2696.3.2.1.3.8.1	GroupAvailability	read-only	Specifies the overall availability of the satellite group of tests and measurements, tr101290Satellite.
OID capabilitySatelliteOID	1.3.6.1.4.1.2696.3.2.1.3.8.2.1.1	OBJECT IDENTIFIER	not-accessible	The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB.
NUM capabilitySatellitePollInterval	1.3.6.1.4.1.2696.3.2.1.3.8.2.1.3	PollingInterval	read-only	Indicates the interval between updates of the information supplied by this object.
capabilitySatelliteTable	1.3.6.1.4.1.2696.3.2.1.3.8.2		not-accessible	Specifies the individual availability of the satellite group of tests and measurements, tr101290Satellite.
capabilityTerrestrial	1.3.6.1.4.1.2696.3.2.1.3.9
AVA capabilityTerrestrialAvailability	1.3.6.1.4.1.2696.3.2.1.3.9.2.1.2	Availability	read-only	The availability of a specific test or measurement
capabilityTerrestrialEntry	1.3.6.1.4.1.2696.3.2.1.3.9.2.1		not-accessible	Row specification
GRO capabilityTerrestrialGroup	1.3.6.1.4.1.2696.3.2.1.3.9.1	GroupAvailability	read-only	Specifies the overall availability of the terrestrial group of tests and measurements, tr101290Terrestrial.
OID capabilityTerrestrialOID	1.3.6.1.4.1.2696.3.2.1.3.9.2.1.1	OBJECT IDENTIFIER	not-accessible	The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB.
NUM capabilityTerrestrialPollInterval	1.3.6.1.4.1.2696.3.2.1.3.9.2.1.3	PollingInterval	read-only	Indicates the interval between updates of the information supplied by this object.
capabilityTerrestrialTable	1.3.6.1.4.1.2696.3.2.1.3.9.2		not-accessible	Specifies the individual availability of the terrestrial group of tests and measurements, tr101290Terrestrial.
capabilityTS	1.3.6.1.4.1.2696.3.2.1.3.5
AVA capabilityTSAvailability	1.3.6.1.4.1.2696.3.2.1.3.5.2.1.2	Availability	read-only	The availability of a specific test or measurement
capabilityTSEntry	1.3.6.1.4.1.2696.3.2.1.3.5.2.1		not-accessible	Row specification
GRO capabilityTSGroup	1.3.6.1.4.1.2696.3.2.1.3.5.1	GroupAvailability	read-only	Specifies the overall availability of the Transport Stream group of tests and measurements, tr101290TS.
OID capabilityTSOID	1.3.6.1.4.1.2696.3.2.1.3.5.2.1.1	OBJECT IDENTIFIER	not-accessible	The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB.
NUM capabilityTSPollInterval	1.3.6.1.4.1.2696.3.2.1.3.5.2.1.3	PollingInterval	read-only	Indicates the interval between updates of the information supplied by this object.
capabilityTSTable	1.3.6.1.4.1.2696.3.2.1.3.5.2		not-accessible	Specifies the individual availability of the Transport Stream group of tests and measurements, tr101290TS.
ACT ciCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 ciCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT ciCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F ciCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA ciCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
ciCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.8.1		not-accessible	Row specification
INP ciCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT ciCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA ciCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.9	MeasurementState	read-only	Indicates the validity of the measurement
ciCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.8		not-accessible	Coherent Interferer measurement
TES ciCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.2	TestState	read-only	This indicates whether the ciCSValue is currently within the thresholds.
NUM ciCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.8.1.10	FloatingPoint	read-only	The current Coherent Interferer value in dB.
complianceCable	1.3.6.1.4.1.2696.3.2.3.1.2			Compliance for Cable RF measurement devices
complianceSatellite	1.3.6.1.4.1.2696.3.2.3.1.3			Compliance for Satellite RF measurement devices
complianceTerrestrial	1.3.6.1.4.1.2696.3.2.3.1.4			Compliance for Terrestrial RF measurement devices
complianceTransportStream	1.3.6.1.4.1.2696.3.2.3.1.1			Compliance for Transport Stream monitor devices
NUM controlEventPersistence	1.3.6.1.4.1.2696.3.2.1.1.2	FloatingPoint	read-write	The persistence timer used with Event errors. An Event error test remains in the 'fail' state for this length of time after the occurrence of the Event.
DAT controlNow	1.3.6.1.4.1.2696.3.2.1.1.1	DateAndTime	read-write	The current date and time at the location of the measurement equipment. It is highly desirable that the offset from UTC should be included. It is possible to set the time and date through this object, but it is expected that most systems will incorporate a more accurate method for doing this.
controlRFSystemEntry	1.3.6.1.4.1.2696.3.2.1.1.3.1		not-accessible	Row specification
controlRFSystemTable	1.3.6.1.4.1.2696.3.2.1.1.3		not-accessible	Table which controls the RF modulation expected to be received on each input.
controlSynchronizationEntry	1.3.6.1.4.1.2696.3.2.1.1.4.1		not-accessible	Row specification
INP controlSynchronizationInputNumber	1.3.6.1.4.1.2696.3.2.1.1.4.1.1	InputNumber	not-accessible	Transport Stream number to which the objects in this row apply.
controlSynchronizationTable	1.3.6.1.4.1.2696.3.2.1.1.4		not-accessible	Table reserved for future specification of synchronized timing.
NUM controlSynchronizedTime	1.3.6.1.4.1.2696.3.2.1.1.4.1.2	FloatingPoint	read-write	This object is reserved pending future standardisation of timestamping of Transport Streams.
ACT csCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 csCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT csCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F csCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA csCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
csCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.4.1		not-accessible	Row specification
INP csCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT csCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA csCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.9	MeasurementState	read-only	Indicates the validity of the measurement
csCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.4		not-accessible	Carrier suppression measurement
TES csCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.2	TestState	read-only	This indicates whether the csCSValue is currently within the thresholds.
NUM csCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.4.1.10	FloatingPoint	read-only	The current Carrier Suppression value in dB.
ACT csTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 csTCounter	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT csTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F csTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA csTEnable	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
csTEntry	1.3.6.1.4.1.2696.3.2.1.9.18.4.1		not-accessible	Row specification
INP csTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT csTLatestError	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA csTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
csTTable	1.3.6.1.4.1.2696.3.2.1.9.18.4		not-accessible	Carrier Suppression (CS) measurement
TES csTTestState	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.2	TestState	read-only	This indicates whether csTValue is currently within the thresholds.
NUM csTValue	1.3.6.1.4.1.2696.3.2.1.9.18.4.1.10	FloatingPoint	read-only	The current Carrier Suppression value in dB.
dvb	1.3.6.1.4.1.2696
ACT eNDCActiveTime	1.3.6.1.4.1.2696.3.2.1.7.4.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 eNDCCounter	1.3.6.1.4.1.2696.3.2.1.7.4.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT eNDCCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.7.4.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F eNDCCounterReset	1.3.6.1.4.1.2696.3.2.1.7.4.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA eNDCEnable	1.3.6.1.4.1.2696.3.2.1.7.4.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
eNDCEntry	1.3.6.1.4.1.2696.3.2.1.7.4.1		not-accessible	Row description
INP eNDCInputNumber	1.3.6.1.4.1.2696.3.2.1.7.4.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT eNDCLatestError	1.3.6.1.4.1.2696.3.2.1.7.4.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA eNDCMeasurementState	1.3.6.1.4.1.2696.3.2.1.7.4.1.9	MeasurementState	read-only	Indicates the validity of the measurement
eNDCTable	1.3.6.1.4.1.2696.3.2.1.7.4		not-accessible	Equivalent Noise Degradation (END) measurement
TES eNDCTestState	1.3.6.1.4.1.2696.3.2.1.7.4.1.2	TestState	read-only	This indicates an error when the eNDCValue exceeds the threshold.
NUM eNDCValue	1.3.6.1.4.1.2696.3.2.1.7.4.1.10	FloatingPoint	read-only	The current Equivalent Noise Degradation value in dB.
eNDT	1.3.6.1.4.1.2696.3.2.1.9.9
ACT eNDTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 eNDTCounter	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT eNDTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F eNDTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA eNDTEnable	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
eNDTEntry	1.3.6.1.4.1.2696.3.2.1.9.9.1.1		not-accessible	Row specification
INP eNDTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT eNDTLatestError	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
ACT eNDTLPActiveTime	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 eNDTLPCounter	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT eNDTLPCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F eNDTLPCounterReset	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA eNDTLPEnable	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
eNDTLPEntry	1.3.6.1.4.1.2696.3.2.1.9.9.3.1		not-accessible	Row specification
INP eNDTLPInputNumber	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT eNDTLPLatestError	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA eNDTLPMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
eNDTLPTable	1.3.6.1.4.1.2696.3.2.1.9.9.3		not-accessible	Equivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'.
TES eNDTLPTestState	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.2	TestState	read-only	This indicates whether eNDTLPValue is within the thresholds.
NUM eNDTLPValue	1.3.6.1.4.1.2696.3.2.1.9.9.3.1.10	FloatingPoint	read-only	The current Equivalent Noise Degradation for the low priority stream expressed in dB.
MEA eNDTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
eNDTTable	1.3.6.1.4.1.2696.3.2.1.9.9.1		not-accessible	Equivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream.
TES eNDTTestState	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.2	TestState	read-only	This indicates whether eNDTValue is within the thresholds.
NUM eNDTValue	1.3.6.1.4.1.2696.3.2.1.9.9.1.1.10	FloatingPoint	read-only	The current Equivalent Noise Degradation expressed in dB.
ACT eNFTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 eNFTCounter	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT eNFTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F eNFTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA eNFTEnable	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
eNFTEntry	1.3.6.1.4.1.2696.3.2.1.9.9.2.1		not-accessible	Row specification
INP eNFTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT eNFTLatestError	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
ACT eNFTLPActiveTime	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 eNFTLPCounter	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT eNFTLPCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F eNFTLPCounterReset	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA eNFTLPEnable	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
eNFTLPEntry	1.3.6.1.4.1.2696.3.2.1.9.9.4.1		not-accessible	Row specification
INP eNFTLPInputNumber	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT eNFTLPLatestError	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA eNFTLPMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
eNFTLPTable	1.3.6.1.4.1.2696.3.2.1.9.9.4		not-accessible	Equivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'.
TES eNFTLPTestState	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.2	TestState	read-only	This indicates whether eNFTLPValue is within the thresholds.
NUM eNFTLPValue	1.3.6.1.4.1.2696.3.2.1.9.9.4.1.10	FloatingPoint	read-only	The current Equivalent Noise Floor for the low priority stream, expressed in dB, see the reference for the method of calculation.
MEA eNFTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
eNFTTable	1.3.6.1.4.1.2696.3.2.1.9.9.2		not-accessible	Equivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream.
TES eNFTTestState	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.2	TestState	read-only	This indicates whether the eNFTValue is within the thresholds.
NUM eNFTValue	1.3.6.1.4.1.2696.3.2.1.9.9.2.1.10	FloatingPoint	read-only	The current Equivalent Noise Floor expressed in dB, see the reference for the method of calculation.
ACT estNoiseMarginActiveTime	1.3.6.1.4.1.2696.3.2.1.7.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 estNoiseMarginCounter	1.3.6.1.4.1.2696.3.2.1.7.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT estNoiseMarginCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.7.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F estNoiseMarginCounterReset	1.3.6.1.4.1.2696.3.2.1.7.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA estNoiseMarginEnable	1.3.6.1.4.1.2696.3.2.1.7.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
estNoiseMarginEntry	1.3.6.1.4.1.2696.3.2.1.7.2.1		not-accessible	Row description
INP estNoiseMarginInputNumber	1.3.6.1.4.1.2696.3.2.1.7.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT estNoiseMarginLatestError	1.3.6.1.4.1.2696.3.2.1.7.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA estNoiseMarginMeasurementState	1.3.6.1.4.1.2696.3.2.1.7.2.1.9	MeasurementState	read-only	Indicates the validity of the measurement
estNoiseMarginTable	1.3.6.1.4.1.2696.3.2.1.7.2		not-accessible	Estimated noise margin measurement
TES estNoiseMarginTestState	1.3.6.1.4.1.2696.3.2.1.7.2.1.2	TestState	read-only	This indicates whether the estNoiseMarginValue is currently within the thresholds.
NUM estNoiseMarginValue	1.3.6.1.4.1.2696.3.2.1.7.2.1.10	FloatingPoint	read-only	The current Estimated Noise Margin value in dB.
groupCable	1.3.6.1.4.1.2696.3.2.3.2.6			Contains all objects relevant to cable RF measurement
groupCapability	1.3.6.1.4.1.2696.3.2.3.2.4			Contains all objects from the tr101290Capability branch of the MIB
groupControl	1.3.6.1.4.1.2696.3.2.3.2.1			Contains all the objects from the tr101290Control branch of the MIB
groupSatellite	1.3.6.1.4.1.2696.3.2.3.2.7			Contains all objects relevent to satellite RF measurements
groupTerrestrial	1.3.6.1.4.1.2696.3.2.3.2.8			Contains all objects relevant to terrestrial RF measurements
groupTransportStream	1.3.6.1.4.1.2696.3.2.3.2.5			Contains all objects relevant to Transport Stream measurement
groupTrapControl	1.3.6.1.4.1.2696.3.2.3.2.2			Contains all the normal objects from the tr101290Trap branch of the MIB
groupTraps	1.3.6.1.4.1.2696.3.2.3.2.3			Contains all the traps/notifications from the MIB.
ACT ifSpectrumActiveTime	1.3.6.1.4.1.2696.3.2.1.8.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 ifSpectrumCounter	1.3.6.1.4.1.2696.3.2.1.8.2.1.4	Counter32	read-only	Count of the number of times an error has occurred for this test.
DAT ifSpectrumCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.8.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F ifSpectrumCounterReset	1.3.6.1.4.1.2696.3.2.1.8.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA ifSpectrumEnable	1.3.6.1.4.1.2696.3.2.1.8.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
ifSpectrumEntry	1.3.6.1.4.1.2696.3.2.1.8.2.1		not-accessible	Row specification
INP ifSpectrumInputNumber	1.3.6.1.4.1.2696.3.2.1.8.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT ifSpectrumLatestError	1.3.6.1.4.1.2696.3.2.1.8.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of an error on this test.
ifSpectrumTable	1.3.6.1.4.1.2696.3.2.1.8.2		not-accessible	IF spectrum test
TES ifSpectrumTestState	1.3.6.1.4.1.2696.3.2.1.8.2.1.2	TestState	read-only	This indicates whether the spectrum conforms to the template. Note that the spectrum mask must be provided to the instrument by means outside the scope of this MIB. The group delay is not tested.
iqAnalysisCS	1.3.6.1.4.1.2696.3.2.1.6.9
iqAnalysisT	1.3.6.1.4.1.2696.3.2.1.9.18
ACT linearityActiveTime	1.3.6.1.4.1.2696.3.2.1.9.10.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 linearityCounter	1.3.6.1.4.1.2696.3.2.1.9.10.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT linearityCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.10.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F linearityCounterReset	1.3.6.1.4.1.2696.3.2.1.9.10.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA linearityEnable	1.3.6.1.4.1.2696.3.2.1.9.10.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
linearityEntry	1.3.6.1.4.1.2696.3.2.1.9.10.1		not-accessible	Row specification
INP linearityInputNumber	1.3.6.1.4.1.2696.3.2.1.9.10.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT linearityLatestError	1.3.6.1.4.1.2696.3.2.1.9.10.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA linearityMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.10.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
linearityTable	1.3.6.1.4.1.2696.3.2.1.9.10		not-accessible	Linearity characterization (shoulder attenuation)
TES linearityTestState	1.3.6.1.4.1.2696.3.2.1.9.10.1.2	TestState	read-only	This indicates whether the linearityValue is above the minimum permitted.
NUM linearityValue	1.3.6.1.4.1.2696.3.2.1.9.10.1.10	FloatingPoint	read-only	The current linearity (shoulder attenuation) expressed in dB.
ACT linkAvailabilityActiveTime	1.3.6.1.4.1.2696.3.2.1.6.2.1.8	ActiveTime	read-only	This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the measurement. It can be used to calculate the Total Time in the calculation of the availability.
C32 linkAvailabilityCounter	1.3.6.1.4.1.2696.3.2.1.6.2.1.4	Counter32	read-only	Count of the number of times the link has become unavailable.
DAT linkAvailabilityCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the linkAvailabilityCounter object.
T/F linkAvailabilityCounterReset	1.3.6.1.4.1.2696.3.2.1.6.2.1.6	TruthValue	read-write	linkAvailabilityCounter is reset to zero and linkAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA linkAvailabilityEnable	1.3.6.1.4.1.2696.3.2.1.6.2.1.3	Enable	read-write	Determines whether link availability testing is performed and whether the associated traps are generated.
linkAvailabilityEntry	1.3.6.1.4.1.2696.3.2.1.6.2.1		not-accessible	Row specification
INP linkAvailabilityInputNumber	1.3.6.1.4.1.2696.3.2.1.6.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
T/F linkAvailabilityInSUTI	1.3.6.1.4.1.2696.3.2.1.6.2.1.12	TruthValue	read-only	This object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Uncorrectable Time Interval (SETI).
DAT linkAvailabilityLatestError	1.3.6.1.4.1.2696.3.2.1.6.2.1.7	DateAndTime	read-only	The timestamp when the link most recently became unavailable.
MEA linkAvailabilityMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.2.1.9	MeasurementState	read-only	Indicates the validity of the measurement
NUM linkAvailabilityRatio	1.3.6.1.4.1.2696.3.2.1.6.2.1.11	FloatingPoint	read-only	This is the Link Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period.
linkAvailabilityTable	1.3.6.1.4.1.2696.3.2.1.6.2		not-accessible	Link availability measurement
TES linkAvailabilityTestState	1.3.6.1.4.1.2696.3.2.1.6.2.1.2	TestState	read-only	A 'fail' is an approximate indication that the system is in a period of link unavailable time (LUAT). 'fail' is indicated as soon as a trigger period for link unavailable time completes. 'pass' is indicated as soon as a trigger period for link available time completes. This necessarily differs from the strict definition of LUAT because the measuring equipment is unable to look into the future.
U32 linkAvailabilityUnavailableTime	1.3.6.1.4.1.2696.3.2.1.6.2.1.10	Unsigned32	read-only	This is a monotonically increasing time in seconds which measures the total link unavailable time (LUAT) since the measuring system was last restarted.
NTF measurementFailTrap	1.3.6.1.4.1.2696.3.2.1.2.0.2			Trap which is sent when a test which is associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' object associated with the test to the 'fail' state from any other state. Transmission of the trap is subject to rate control and to the enable status of each test.
NTF measurementUnknownTrap	1.3.6.1.4.1.2696.3.2.1.2.0.3			Trap which is sent when a measurement value becomes unavailable. This trap is triggered by the transition of the '...MeasurementState' object associated with the measurement to the 'unknown' state from any other state. Transmission of the trap is subject to rate control.
ACT merCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 merCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT merCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the merCSCounter object.
T/F merCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.6	TruthValue	read-write	merCSCounter is reset to zero and merCSCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA merCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
merCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.2.1		not-accessible	Row specification
INP merCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT merCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA merCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.9	MeasurementState	read-only	Indicates the validity of the measurement
merCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.2		not-accessible	Modulation Error Ratio (MER)
TES merCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.2	TestState	read-only	This indicates whether the merCSValue is currently below the maximum limit.
NUM merCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.2.1.10	FloatingPoint	read-only	The Modulation Error Ratio expressed in dB
ACT merTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 merTCounter	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT merTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the merTCounter object.
T/F merTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA merTEnable	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
merTEntry	1.3.6.1.4.1.2696.3.2.1.9.18.2.1		not-accessible	Row specification
INP merTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT merTLatestError	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA merTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
merTTable	1.3.6.1.4.1.2696.3.2.1.9.18.2		not-accessible	Modulation Error Ratio (MER) measurement
TES merTTestState	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.2	TestState	read-only	This indicates whether merTValue is within the thresholds.
NUM merTValue	1.3.6.1.4.1.2696.3.2.1.9.18.2.1.10	FloatingPoint	read-only	The current Modulation Error Ratio expressed in dB
mg	1.3.6.1.4.1.2696.3
ACT mipSyntaxActiveTime	1.3.6.1.4.1.2696.3.2.1.9.20.1.9	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 mipSyntaxCounter	1.3.6.1.4.1.2696.3.2.1.9.20.1.5	Counter32	read-only	Count of the number of times this error has occurred
DAT mipSyntaxCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.20.1.6	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the mipSyntaxCounter object.
T/F mipSyntaxCounterReset	1.3.6.1.4.1.2696.3.2.1.9.20.1.7	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA mipSyntaxEnable	1.3.6.1.4.1.2696.3.2.1.9.20.1.4	Enable	read-write	Determines whether this test and the associated trap are enabled.
mipSyntaxEntry	1.3.6.1.4.1.2696.3.2.1.9.20.1		not-accessible	Row specification
INP mipSyntaxInputNumber	1.3.6.1.4.1.2696.3.2.1.9.20.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT mipSyntaxLatestError	1.3.6.1.4.1.2696.3.2.1.9.20.1.8	DateAndTime	read-only	The timestamp at the most recent occurrence of the error
TES mipSyntaxState	1.3.6.1.4.1.2696.3.2.1.9.20.1.3	TestState	read-only	This gives the overall pass/fail state of the test.
mipSyntaxTable	1.3.6.1.4.1.2696.3.2.1.9.20		not-accessible	SFN MIP baseband tests
IND mipSyntaxTestNumber	1.3.6.1.4.1.2696.3.2.1.9.20.1.2	IndexMIPSyntaxTest	not-accessible	The specific SFN MIP test that this row applies to
ACT noiseMarginActiveTime	1.3.6.1.4.1.2696.3.2.1.7.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 noiseMarginCounter	1.3.6.1.4.1.2696.3.2.1.7.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT noiseMarginCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.7.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F noiseMarginCounterReset	1.3.6.1.4.1.2696.3.2.1.7.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA noiseMarginEnable	1.3.6.1.4.1.2696.3.2.1.7.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
noiseMarginEntry	1.3.6.1.4.1.2696.3.2.1.7.1.1		not-accessible	Row description
INP noiseMarginInputNumber	1.3.6.1.4.1.2696.3.2.1.7.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT noiseMarginLatestError	1.3.6.1.4.1.2696.3.2.1.7.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA noiseMarginMeasurementState	1.3.6.1.4.1.2696.3.2.1.7.1.1.9	MeasurementState	read-only	Indicates the validity of the measurement
noiseMarginTable	1.3.6.1.4.1.2696.3.2.1.7.1		not-accessible	Noise margin measurement
TES noiseMarginTestState	1.3.6.1.4.1.2696.3.2.1.7.1.1.2	TestState	read-only	This indicates whether the noiseMarginValue is currently within the thresholds.
NUM noiseMarginValue	1.3.6.1.4.1.2696.3.2.1.7.1.1.10	FloatingPoint	read-only	The current Noise Margin value in dB.
ACT noisePowerActiveTime	1.3.6.1.4.1.2696.3.2.1.6.7.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 noisePowerCounter	1.3.6.1.4.1.2696.3.2.1.6.7.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT noisePowerCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.7.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the noisePowerCounter object.
T/F noisePowerCounterReset	1.3.6.1.4.1.2696.3.2.1.6.7.1.6	TruthValue	read-write	noisePowerCounter is reset to zero and noisePowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA noisePowerEnable	1.3.6.1.4.1.2696.3.2.1.6.7.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
noisePowerEntry	1.3.6.1.4.1.2696.3.2.1.6.7.1		not-accessible	Row specification
INP noisePowerInputNumber	1.3.6.1.4.1.2696.3.2.1.6.7.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT noisePowerLatestError	1.3.6.1.4.1.2696.3.2.1.6.7.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA noisePowerMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.7.1.9	MeasurementState	read-only	Indicates the validity of the measurement
noisePowerTable	1.3.6.1.4.1.2696.3.2.1.6.7		not-accessible	Noise power measurement
TES noisePowerTestState	1.3.6.1.4.1.2696.3.2.1.6.7.1.2	TestState	read-only	This indicates whether the noisePowerValue is currently below the maximum limit.
NUM noisePowerValue	1.3.6.1.4.1.2696.3.2.1.6.7.1.10	FloatingPoint	read-only	The current RF noise power expressed in dBm, which references 0 dBm as the power of 1 mW.
ACT outBandEmissActiveTime	1.3.6.1.4.1.2696.3.2.1.7.5.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 outBandEmissCounter	1.3.6.1.4.1.2696.3.2.1.7.5.1.4	Counter32	read-only	Count of the number of times an error has occurred for this test.
DAT outBandEmissCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.7.5.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F outBandEmissCounterReset	1.3.6.1.4.1.2696.3.2.1.7.5.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA outBandEmissEnable	1.3.6.1.4.1.2696.3.2.1.7.5.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
outBandEmissEntry	1.3.6.1.4.1.2696.3.2.1.7.5.1		not-accessible	Row specification
INP outBandEmissInputNumber	1.3.6.1.4.1.2696.3.2.1.7.5.1.1	InputNumber	not-accessible	Transport Stream on which the test is made
DAT outBandEmissLatestError	1.3.6.1.4.1.2696.3.2.1.7.5.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of an error on this test.
outBandEmissTable	1.3.6.1.4.1.2696.3.2.1.7.5		not-accessible	Out of band emissions test
TES outBandEmissTestState	1.3.6.1.4.1.2696.3.2.1.7.5.1.2	TestState	read-only	This indicates whether the spectrum is within the spectrum mask. Note that the spectrum mask must be provided to the instrument by means outside the scope of this MIB.
ACT pjCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 pjCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT pjCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F pjCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA pjCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
pjCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.9.1		not-accessible	Row specification
INP pjCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT pjCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA pjCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.9	MeasurementState	read-only	Indicates the validity of the measurement
pjCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.9		not-accessible	Phase Jitter (PJ) measurement
TES pjCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.2	TestState	read-only	This indicates whether the pjCSValue is currently within the thresholds.
NUM pjCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.9.1.10	FloatingPoint	read-only	The current Phase Jitter value in degrees.
ACT pjTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 pjTCounter	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT pjTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F pjTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA pjTEnable	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
pjTEntry	1.3.6.1.4.1.2696.3.2.1.9.18.7.1		not-accessible	Row specification
INP pjTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT pjTLatestError	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA pjTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
pjTTable	1.3.6.1.4.1.2696.3.2.1.9.18.7		not-accessible	Phase Jitter (PJ) measurement
TES pjTTestState	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.2	TestState	read-only	This indicates whether pjTValue is currently within the thresholds.
NUM pjTValue	1.3.6.1.4.1.2696.3.2.1.9.18.7.1.10	FloatingPoint	read-only	The current Phase Jitter value in degrees.
ACT qeCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 qeCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT qeCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F qeCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA qeCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
qeCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.6.1		not-accessible	Row specification
INP qeCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT qeCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA qeCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.9	MeasurementState	read-only	Indicates the validity of the measurement
qeCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.6		not-accessible	Quadrature Error (QE) measurement
TES qeCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.2	TestState	read-only	This indicates whether the qeCSValue is currently within the thresholds.
NUM qeCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.6.1.10	FloatingPoint	read-only	The current Quadrature Error value in degrees.
ACT qeTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 qeTCounter	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT qeTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F qeTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA qeTEnable	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
qeTEntry	1.3.6.1.4.1.2696.3.2.1.9.18.6.1		not-accessible	Row specification
INP qeTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT qeTLatestError	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA qeTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
qeTTable	1.3.6.1.4.1.2696.3.2.1.9.18.6		not-accessible	Quadrature Error (QE) measurement
TES qeTTestState	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.2	TestState	read-only	This indicates whether qeTValue is currently within the thresholds.
NUM qeTValue	1.3.6.1.4.1.2696.3.2.1.9.18.6.1.10	FloatingPoint	read-only	The current Quadrature Error value in degrees.
ACT rfAccuracyActiveTime	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 rfAccuracyCounter	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT rfAccuracyCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F rfAccuracyCounterReset	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA rfAccuracyEnable	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
rfAccuracyEntry	1.3.6.1.4.1.2696.3.2.1.9.1.1.1		not-accessible	Row specification
INP rfAccuracyInputNumber	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.1	InputNumber	not-accessible	RF input on which the measurement is made
DAT rfAccuracyLatestError	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA rfAccuracyMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.9	MeasurementState	read-only	Indicates the validity of the measurement
rfAccuracyTable	1.3.6.1.4.1.2696.3.2.1.9.1.1		not-accessible	RF frequency accuracy (Precision)
TES rfAccuracyTestState	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.2	TestState	read-only	This indicates whether the rfAccuracyValue is within the thresholds.
NUM rfAccuracyValue	1.3.6.1.4.1.2696.3.2.1.9.1.1.1.10	FloatingPoint	read-only	This is the RF carrier frequency in Hz.
ACT rfChannelWidthActiveTime	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 rfChannelWidthCounter	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT rfChannelWidthCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F rfChannelWidthCounterReset	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA rfChannelWidthEnable	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
rfChannelWidthEntry	1.3.6.1.4.1.2696.3.2.1.9.1.2.1		not-accessible	Row specification
INP rfChannelWidthInputNumber	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT rfChannelWidthLatestError	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA rfChannelWidthMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
rfChannelWidthTable	1.3.6.1.4.1.2696.3.2.1.9.1.2		not-accessible	RF channel width (Sampling Frequency Accuracy)
TES rfChannelWidthTestState	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.2	TestState	read-only	This indicates whether the rfChannelWidthValue is within the thresholds.
NUM rfChannelWidthValue	1.3.6.1.4.1.2696.3.2.1.9.1.2.1.10	FloatingPoint	read-only	This is the RF channel width in Hz.
ACT rfIfPowerActiveTime	1.3.6.1.4.1.2696.3.2.1.9.5.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 rfIfPowerCounter	1.3.6.1.4.1.2696.3.2.1.9.5.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT rfIfPowerCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.5.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F rfIfPowerCounterReset	1.3.6.1.4.1.2696.3.2.1.9.5.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA rfIfPowerEnable	1.3.6.1.4.1.2696.3.2.1.9.5.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
rfIfPowerEntry	1.3.6.1.4.1.2696.3.2.1.9.5.1		not-accessible	Row specification
INP rfIfPowerInputNumber	1.3.6.1.4.1.2696.3.2.1.9.5.1.1	InputNumber	not-accessible	RF input on which the measurement is made
DAT rfIfPowerLatestError	1.3.6.1.4.1.2696.3.2.1.9.5.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA rfIfPowerMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.5.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
rfIfPowerTable	1.3.6.1.4.1.2696.3.2.1.9.5		not-accessible	RF/IF signal power
TES rfIfPowerTestState	1.3.6.1.4.1.2696.3.2.1.9.5.1.2	TestState	read-only	This indicates whether the rfIfPowerValue is within the thresholds.
NUM rfIfPowerValue	1.3.6.1.4.1.2696.3.2.1.9.5.1.10	FloatingPoint	read-only	The current RF power expressed in dBm, which references 0 dBm as the power of 1 mW.
ACT rfIFsignalPowerActiveTime	1.3.6.1.4.1.2696.3.2.1.6.6.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 rfIFsignalPowerCounter	1.3.6.1.4.1.2696.3.2.1.6.6.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT rfIFsignalPowerCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.6.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the rfIFsignalPowerCounter object.
T/F rfIFsignalPowerCounterReset	1.3.6.1.4.1.2696.3.2.1.6.6.1.6	TruthValue	read-write	rfIFsignalPowerCounter is reset to zero and rfIFsignalPowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA rfIFsignalPowerEnable	1.3.6.1.4.1.2696.3.2.1.6.6.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
rfIFsignalPowerEntry	1.3.6.1.4.1.2696.3.2.1.6.6.1		not-accessible	Row specification
INP rfIFsignalPowerInputNumber	1.3.6.1.4.1.2696.3.2.1.6.6.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT rfIFsignalPowerLatestError	1.3.6.1.4.1.2696.3.2.1.6.6.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA rfIFsignalPowerMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.6.1.9	MeasurementState	read-only	Indicates the validity of the measurement
rfIFsignalPowerTable	1.3.6.1.4.1.2696.3.2.1.6.6		not-accessible	RF or IF signal power measurement
TES rfIFsignalPowerTestState	1.3.6.1.4.1.2696.3.2.1.6.6.1.2	TestState	read-only	This indicates whether the rfIFsignalPowerValue is currently within the thresholds.
NUM rfIFsignalPowerValue	1.3.6.1.4.1.2696.3.2.1.6.6.1.10	FloatingPoint	read-only	The current RF power expressed in dBm, which references 0 dBm as the power of 1 mW.
ACT rfIfSpectrumActiveTime	1.3.6.1.4.1.2696.3.2.1.9.7.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 rfIfSpectrumCounter	1.3.6.1.4.1.2696.3.2.1.9.7.1.4	Counter32	read-only	Count of the number of times an error has occurred.
DAT rfIfSpectrumCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.7.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F rfIfSpectrumCounterReset	1.3.6.1.4.1.2696.3.2.1.9.7.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA rfIfSpectrumEnable	1.3.6.1.4.1.2696.3.2.1.9.7.1.3	Enable	read-write	Determines whether the spectrum mask test and the associated trap are enabled.
rfIfSpectrumEntry	1.3.6.1.4.1.2696.3.2.1.9.7.1		not-accessible	Row specification
INP rfIfSpectrumInputNumber	1.3.6.1.4.1.2696.3.2.1.9.7.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT rfIfSpectrumLatestError	1.3.6.1.4.1.2696.3.2.1.9.7.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of an error.
rfIfSpectrumTable	1.3.6.1.4.1.2696.3.2.1.9.7		not-accessible	RF and IF spectrum mask test
TES rfIfSpectrumTestState	1.3.6.1.4.1.2696.3.2.1.9.7.1.2	TestState	read-only	This indicates whether the signal conforms to the spectrum mask
DEL rfSystemDelivery	1.3.6.1.4.1.2696.3.2.1.1.3.1.2	DeliverySystemType	read-write	The type of signal the instrument should expect at its input.
INP rfSystemInputNumber	1.3.6.1.4.1.2696.3.2.1.1.3.1.1	InputNumber	not-accessible	RF input whose mode of operation is to be set
rfTerr	1.3.6.1.4.1.2696.3.2.1.9.1
ACT rteCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 rteCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT rteCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F rteCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA rteCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
rteCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.7.1		not-accessible	Row description
INP rteCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT rteCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA rteCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.9	MeasurementState	read-only	Indicates the validity of the measurement
rteCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.7		not-accessible	Residual Target Error (RTE) measurement
TES rteCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.2	TestState	read-only	This indicates whether the rteCSValue is currently within the thresholds.
NUM rteCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.7.1.10	FloatingPoint	read-only	The current Residual Target Error value as a numeric value.
NUM satellitePrefBERMax	1.3.6.1.4.1.2696.3.2.1.8.100.1.2	FloatingPoint	read-write	This defines the upper limit on the BER before Viterbi measurement
satellitePreferencesEntry	1.3.6.1.4.1.2696.3.2.1.8.100.1		not-accessible	Row specification
satellitePreferencesTable	1.3.6.1.4.1.2696.3.2.1.8.100		not-accessible	Table of satellite specific measurement preferences.
INP satellitePrefInputNumber	1.3.6.1.4.1.2696.3.2.1.8.100.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
ACT sepEtiActiveTime	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 sepEtiCounter	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.4	Counter32	read-only	Count of the number of times an ETI has occurred.
DAT sepEtiCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F sepEtiCounterReset	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA sepEtiEnable	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
sepEtiEntry	1.3.6.1.4.1.2696.3.2.1.9.21.1.1		not-accessible	Row specification
INP sepEtiInputNumber	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT sepEtiLatestError	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of an ETI.
MEA sepEtiMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
sepEtiTable	1.3.6.1.4.1.2696.3.2.1.9.21.1		not-accessible	Measurement of Errored Second Ratio (ESR) or Errored Time Interval Ratio (ETIR).
TES sepEtiTestState	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.2	TestState	read-only	A 'fail' indicaties that the most recently completed time interval TI was an Errored Time Interval (ETI). A 'pass' indicates that the most recent TI was not errored.
NUM sepEtiValue	1.3.6.1.4.1.2696.3.2.1.9.21.1.1.10	FloatingPoint	read-only	This is the Errored Time Interval Ratio (ETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value.
ACT sepSetiActiveTime	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 sepSetiCounter	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.4	Counter32	read-only	Count of the number of times an SETI has occurred.
DAT sepSetiCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F sepSetiCounterReset	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA sepSetiEnable	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
sepSetiEntry	1.3.6.1.4.1.2696.3.2.1.9.21.2.1		not-accessible	Row specification
INP sepSetiInputNumber	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT sepSetiLatestError	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a SETI.
MEA sepSetiMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
sepSetiTable	1.3.6.1.4.1.2696.3.2.1.9.21.2		not-accessible	Measurement of Severly Errored Second Ratio (SESR) or Severely Errored Time Interval Ratio (SETIR).
TES sepSetiTestState	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.2	TestState	read-only	A 'fail' indicaties that the most recently completed time interval TI was a Severely Errored Time Interval (SETI). A 'pass' indicates that the most recent TI was not severely errored.
NUM sepSetiValue	1.3.6.1.4.1.2696.3.2.1.9.21.2.1.10	FloatingPoint	read-only	This is the Severely Errored Time Interval Ratio (SETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value.
ACT signQualMarTActiveTime	1.3.6.1.4.1.2696.3.2.1.7.3.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 signQualMarTCounter	1.3.6.1.4.1.2696.3.2.1.7.3.1.4	Counter32	read-only	Count of the number of times an error has occurred.
DAT signQualMarTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.7.3.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F signQualMarTCounterReset	1.3.6.1.4.1.2696.3.2.1.7.3.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA signQualMarTEnable	1.3.6.1.4.1.2696.3.2.1.7.3.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
signQualMarTEntry	1.3.6.1.4.1.2696.3.2.1.7.3.1		not-accessible	Row description
INP signQualMarTInputNumber	1.3.6.1.4.1.2696.3.2.1.7.3.1.1	InputNumber	not-accessible	Transport Stream on which the test is done
DAT signQualMarTLatestError	1.3.6.1.4.1.2696.3.2.1.7.3.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of an error.
signQualMarTTable	1.3.6.1.4.1.2696.3.2.1.7.3		not-accessible	Signal quality margin test
TES signQualMarTTestState	1.3.6.1.4.1.2696.3.2.1.7.3.1.2	TestState	read-only	This indicates an error if the percentage of IQ points outside the threshold box exceeds cablePrefSignQualPercentMax.
ACT snrCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 snrCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT snrCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F snrCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA snrCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
snrCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.10.1		not-accessible	Row specification
INP snrCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT snrCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA snrCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.9	MeasurementState	read-only	Indicates the validity of the measurement
snrCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.10		not-accessible	Signal-to-Noise Ratio (SNR)
TES snrCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.2	TestState	read-only	This indicates whether the snrCSValue is currently within the thresholds.
NUM snrCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.10.1.10	FloatingPoint	read-only	The current Signal-to-Noise value in dB.
steCS	1.3.6.1.4.1.2696.3.2.1.6.9.3
ACT steDeviationCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 steDeviationCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT steDeviationCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F steDeviationCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA steDeviationCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
steDeviationCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1		not-accessible	Row specification
INP steDeviationCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT steDeviationCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA steDeviationCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.9	MeasurementState	read-only	Indicates the validity of the measurement
steDeviationCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.3.2		not-accessible	System Target Error (deviation value)
TES steDeviationCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.2	TestState	read-only	This indicates whether the steDeviationCSValue is currently within the thresholds.
NUM steDeviationCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.10	FloatingPoint	read-only	The current System Target Error Deviation as a numeric value
ACT steDeviationTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 steDeviationTCounter	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT steDeviationTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F steDeviationTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA steDeviationTEnable	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
steDeviationTEntry	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1		not-accessible	Row specification
INP steDeviationTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT steDeviationTLatestError	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA steDeviationTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
steDeviationTTable	1.3.6.1.4.1.2696.3.2.1.9.18.3.2		not-accessible	System Target Error Deviation (STED) measurement
TES steDeviationTTestState	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.2	TestState	read-only	This indicates whether steDeviationTValue is currently within the thresholds.
NUM steDeviationTValue	1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.10	FloatingPoint	read-only	The current System Target Error Deviation as a numeric value
ACT steMeanCSActiveTime	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 steMeanCSCounter	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT steMeanCSCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F steMeanCSCounterReset	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA steMeanCSEnable	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
steMeanCSEntry	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1		not-accessible	Row specification
INP steMeanCSInputNumber	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT steMeanCSLatestError	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA steMeanCSMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.9	MeasurementState	read-only	Indicates the validity of the measurement
steMeanCSTable	1.3.6.1.4.1.2696.3.2.1.6.9.3.1		not-accessible	System Target Error (mean value)
TES steMeanCSTestState	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.2	TestState	read-only	This indicates whether the steMeanCSValue is currently within the thresholds.
NUM steMeanCSValue	1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.10	FloatingPoint	read-only	The current System Target Error Mean as a numeric value
ACT steMeanTActiveTime	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 steMeanTCounter	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT steMeanTCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F steMeanTCounterReset	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA steMeanTEnable	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
steMeanTEntry	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1		not-accessible	Row specification
INP steMeanTInputNumber	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT steMeanTLatestError	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA steMeanTMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
steMeanTTable	1.3.6.1.4.1.2696.3.2.1.9.18.3.1		not-accessible	System Target Error Mean (STEM) measurement
TES steMeanTTestState	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.2	TestState	read-only	This indicates whether steMeanTValue is currently within the thresholds.
NUM steMeanTValue	1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.10	FloatingPoint	read-only	The current System Target Error Mean as a numeric value
steT	1.3.6.1.4.1.2696.3.2.1.9.18.3
ACT symbolLengthActiveTime	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 symbolLengthCounter	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT symbolLengthCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the counter object.
T/F symbolLengthCounterReset	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.6	TruthValue	read-write	The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.
ENA symbolLengthEnable	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
symbolLengthEntry	1.3.6.1.4.1.2696.3.2.1.9.1.3.1		not-accessible	Row specification
INP symbolLengthInputNumber	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT symbolLengthLatestError	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA symbolLengthMeasurementState	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.9	MeasurementState	read-only	Specifies the validity of the measurement value
symbolLengthTable	1.3.6.1.4.1.2696.3.2.1.9.1.3		not-accessible	Symbol Length measurement at RF (Guard Interval verification)
TES symbolLengthTestState	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.2	TestState	read-only	This indicates whether the symbolLengthValue is within the thresholds.
NUM symbolLengthValue	1.3.6.1.4.1.2696.3.2.1.9.1.3.1.10	FloatingPoint	read-only	This is the symbol length in microseconds.
ACT sysAvailabilityActiveTime	1.3.6.1.4.1.2696.3.2.1.6.1.1.8	ActiveTime	read-only	This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the test/measurement. It can be used to calculate the Total Time in the calculation of the availability.
C32 sysAvailabilityCounter	1.3.6.1.4.1.2696.3.2.1.6.1.1.4	Counter32	read-only	Count of the number of times the system has become unavailable
DAT sysAvailabilityCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.6.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the sysAvailabilityCounter object.
T/F sysAvailabilityCounterReset	1.3.6.1.4.1.2696.3.2.1.6.1.1.6	TruthValue	read-write	sysAvailabilityCounter is reset to zero and sysAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA sysAvailabilityEnable	1.3.6.1.4.1.2696.3.2.1.6.1.1.3	Enable	read-write	Determines whether system availability testing is performed and whether the associated traps are generated.
sysAvailabilityEntry	1.3.6.1.4.1.2696.3.2.1.6.1.1		not-accessible	Row specification
INP sysAvailabilityInputNumber	1.3.6.1.4.1.2696.3.2.1.6.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
T/F sysAvailabilityInSETI	1.3.6.1.4.1.2696.3.2.1.6.1.1.12	TruthValue	read-only	This object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Errored Time Interval (SETI).
DAT sysAvailabilityLatestError	1.3.6.1.4.1.2696.3.2.1.6.1.1.7	DateAndTime	read-only	The timestamp when the system most recently became unavailable.
MEA sysAvailabilityMeasurementState	1.3.6.1.4.1.2696.3.2.1.6.1.1.9	MeasurementState	read-only	Indicates the validity of the measurement
NUM sysAvailabilityRatio	1.3.6.1.4.1.2696.3.2.1.6.1.1.11	FloatingPoint	read-only	This is the System Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period.
sysAvailabilityTable	1.3.6.1.4.1.2696.3.2.1.6.1		not-accessible	System availability measurement
TES sysAvailabilityTestState	1.3.6.1.4.1.2696.3.2.1.6.1.1.2	TestState	read-only	A 'fail' is an approximate indication that the system is in a period of unavailable time (UAT). 'fail' is indicated as soon as a trigger period for unavailable time completes. 'pass' is indicated as soon as a trigger period for available time completes. This necessarily differs from the strict definition of UAT because the measuring equipment is unable to look into the future.
U32 sysAvailabilityUnavailableTime	1.3.6.1.4.1.2696.3.2.1.6.1.1.10	Unsigned32	read-only	This is a monotonically increasing time in seconds which measures the total Unavailable Time (UAT) since the measuring system was last restarted.
systemErrorPerformance	1.3.6.1.4.1.2696.3.2.1.9.21
NUM terrestrialPrefAiMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.32	FloatingPoint	read-write	If aiTValue exceeds this value, the associated test fails.
NUM terrestrialPrefBandwidth	1.3.6.1.4.1.2696.3.2.1.9.100.1.3	FloatingPoint	read-write	The instrument is set to expect a DVB-T transmission adapted for this bandwidth. Normal values will be 6.0MHz, 7.0MHz or 8.0MHz.
NUM terrestrialPrefBERRSLPMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.27	FloatingPoint	read-write	If the BER measured by berRSLPValue exceeds this value, an error is indicated.
NUM terrestrialPrefBERRSMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.26	FloatingPoint	read-write	If the BER measured by berRSValue exceeds this value, an error is indicated.
NUM terrestrialPrefBERViterbiLPMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.25	FloatingPoint	read-write	If the BER measured by berViterbiTLPValue exceeds this value, an error is indicated.
NUM terrestrialPrefBERViterbiMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.24	FloatingPoint	read-write	If the BER measured by berViterbiTValue exceeds this value, an error is indicated.
NUM terrestrialPrefCentreFreqExpected	1.3.6.1.4.1.2696.3.2.1.9.100.1.8	FloatingPoint	read-write	This is the expected value for the centre frequency as measured by rfAccuracyValue.
NUM terrestrialPrefCentreFreqLimit	1.3.6.1.4.1.2696.3.2.1.9.100.1.9	FloatingPoint	read-write	This is the permitted deviation for the centre frequency as measured by rfAccuracyValue. If rfAccuracyValue is outside the range: [terrestrialPrefCentreFreqExpected - terrestrialPrefCentreFreqLimit .. terrestrialPrefCentreFreqExpected + terrestrialPrefCentreFreqLimit] an error will be indicated.
NUM terrestrialPrefCentreFrequency	1.3.6.1.4.1.2696.3.2.1.9.100.1.2	FloatingPoint	read-write	This is the centre frequency to which the measuring equipment is tuned for making terrestrial measurements. This frequency is the actual input frequency to the measuring equipment, which may be at an intermediate frequency (IF) rather than the final RF.
NUM terrestrialPrefChannelWidthLimit	1.3.6.1.4.1.2696.3.2.1.9.100.1.10	FloatingPoint	read-write	This is the permitted deviation for the channel width as measured by rfChannelWidthValue. The nominal value of the channel width has a fixed value which depends on the bandwidth (as set by terrestrialPrefBandwidth). If rfChannelWidthValue is outside the range [nominalWidth - terrestrialPrefChannelWidthLimit .. nominalWidth + terrestrialPrefChannelWidthLimit] an error will be indicated.
NUM terrestrialPrefCsMin	1.3.6.1.4.1.2696.3.2.1.9.100.1.31	FloatingPoint	read-write	If csTValue is less than this value, the associated test fails
NUM terrestrialPrefENDBER	1.3.6.1.4.1.2696.3.2.1.9.100.1.14	FloatingPoint	read-write	BER value which is to be used for the END and ENF measurements.
NUM terrestrialPrefENDIdeal	1.3.6.1.4.1.2696.3.2.1.9.100.1.15	FloatingPoint	read-write	This is the 'ideal' value of C/N for measurement of END on the whole or high priority stream. It is used in the measurement of eNDTValue.
NUM terrestrialPrefENDLPIdeal	1.3.6.1.4.1.2696.3.2.1.9.100.1.19	FloatingPoint	read-write	This is the 'ideal' value of C/N for measurement of END on the low priority stream. It is used in the measurement of eNDTLPValue.
NUM terrestrialPrefENDLPMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.20	FloatingPoint	read-write	If the measured value of eNDTLPValue exceeds this, the associated test fails.
NUM terrestrialPrefENDMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.16	FloatingPoint	read-write	If the measured value of eNDTValue exceeds this, the associated test fails.
NUM terrestrialPrefENFIdeal	1.3.6.1.4.1.2696.3.2.1.9.100.1.17	FloatingPoint	read-write	This is the 'ideal' value of C/N for measurement of ENF on the whole or high priority stream. It is used in the measurement of eNFTValue.
NUM terrestrialPrefENFLPIdeal	1.3.6.1.4.1.2696.3.2.1.9.100.1.21	FloatingPoint	read-write	This is the 'ideal' value of C/N for measurement of ENF on the low priority stream. It is used in the measurement of eNFTLPValue.
NUM terrestrialPrefENFLPMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.22	FloatingPoint	read-write	If the measured value of eNFTLPValue exeeds this value, the associated test fails.
NUM terrestrialPrefENFMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.18	FloatingPoint	read-write	If the measured value of eNFTValue is exceeds this value, the associated test fails.
terrestrialPreferencesEntry	1.3.6.1.4.1.2696.3.2.1.9.100.1		not-accessible	Row specification
terrestrialPreferencesTable	1.3.6.1.4.1.2696.3.2.1.9.100		not-accessible	Table of terrestrial specific measurement preferences.
NUM terrestrialPrefGuardInterval	1.3.6.1.4.1.2696.3.2.1.9.100.1.6	GuardInterval	read-write	The instrument is set to expect a transmission using the guard interval specified by this object.
HIE terrestrialPrefHierarchical	1.3.6.1.4.1.2696.3.2.1.9.100.1.7	Hierarchy	read-write	The instrument is set according to the value of this object to expect a transmission which is either non-hierachical or hierarchical using the specified alpha value.
INP terrestrialPrefInputNumber	1.3.6.1.4.1.2696.3.2.1.9.100.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
NUM terrestrialPrefLinearityMin	1.3.6.1.4.1.2696.3.2.1.9.100.1.23	FloatingPoint	read-write	If the shoulder attenuation as measured by linearityValue is less than this value, an error is indicated.
NUM terrestrialPrefMerTMin	1.3.6.1.4.1.2696.3.2.1.9.100.1.28	FloatingPoint	read-write	If merTValue is less than this value, the associated test fails.
NUM terrestrialPrefMIPDeviationMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.36	FloatingPoint	read-write	This preference affects the MIP_ts_rate_error test. It is the value of Max_deviation in the inequality given in TR 101 290 as the condition for an error indication.
NUM terrestrialPrefMIPTimingLimit	1.3.6.1.4.1.2696.3.2.1.9.100.1.35	FloatingPoint	read-write	This preference affects the MIP_timing_error test. If the calculated value of nT differs from an integral number of seconds by more than terrestrialPrefMIPTimingLimit then an error is indicated.
MOD terrestrialPrefModulation	1.3.6.1.4.1.2696.3.2.1.9.100.1.4	Modulation	read-write	This is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to terrestrial measurements.
NUM terrestrialPrefPjMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.34	FloatingPoint	read-write	If pjTValue exceeds this value, the associated test fails.
NUM terrestrialPrefPowerMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.13	FloatingPoint	read-write	If the power measured by rfIfPowerValue is greater than this value, the associated test fails.
NUM terrestrialPrefPowerMin	1.3.6.1.4.1.2696.3.2.1.9.100.1.12	FloatingPoint	read-write	If the power measured by rfIfPowerValue is less than this value, the associated test fails.
NUM terrestrialPrefQeMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.33	FloatingPoint	read-write	If qeTValue exceeds this value, the associated test fails.
NUM terrestrialPrefSEPEBPerCent	1.3.6.1.4.1.2696.3.2.1.9.100.1.42	FloatingPoint	read-write	If more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values are: '1.53', '10', '0.33'.
U32 terrestrialPrefSEPM	1.3.6.1.4.1.2696.3.2.1.9.100.1.40	Unsigned32	read-write	The M value used to identify the start and end of a period of unavailable time (UAT).
NUM terrestrialPrefSEPMeasurementInterval	1.3.6.1.4.1.2696.3.2.1.9.100.1.43	FloatingPoint	read-write	The Measurement Interval (MI) over which the ESR/ETIR and SESR/SETIR are calculated.
U32 terrestrialPrefSEPN	1.3.6.1.4.1.2696.3.2.1.9.100.1.38	Unsigned32	read-write	The N value used to identify the start and end of a period of unavailable time (UAT).
NUM terrestrialPrefSEPT	1.3.6.1.4.1.2696.3.2.1.9.100.1.39	FloatingPoint	read-write	The T value used to identify the start and end of a period of unavailable time (UAT).
NUM terrestrialPrefSEPTI	1.3.6.1.4.1.2696.3.2.1.9.100.1.41	FloatingPoint	read-write	Each Time Interval of this length is assessed as to whether it is an Errored Time Interval or a Severely Errored Time Interval.
UAT terrestrialPrefSEPUATMode	1.3.6.1.4.1.2696.3.2.1.9.100.1.37	UATMode	read-write	Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored.
NUM terrestrialPrefSteDeviationMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.30	FloatingPoint	read-write	If steDeviationTValue exceeds this value, the associated test fails.
NUM terrestrialPrefSteMeanMax	1.3.6.1.4.1.2696.3.2.1.9.100.1.29	FloatingPoint	read-write	If steMeanTValue exceeds this value, the associated test fails.
NUM terrestrialPrefSymbolLengthLimit	1.3.6.1.4.1.2696.3.2.1.9.100.1.11	FloatingPoint	read-write	This is the permitted deviation for the symbol length as measured by symbolLengthValue. The nominal value of the symbol length has a fixed value which depends on the bandwidth, the mode and the guard interval (as set by terrestrialPrefBandwidth, terrestrialPrefTransmissionMode and terrestrialPrefGuardInterval respectively). If symbolLengthValue is outside the range [nominalLength - terrestrialPrefSymbolLengthLimit .. nominalLength + terrestrialPrefSymbolLengthLimit] an error will be indicated.
TER terrestrialPrefTransmissionMode	1.3.6.1.4.1.2696.3.2.1.9.100.1.5	TerrestrialTransmissionMode	read-write	The instrument is set to expect a transmission in either 2k mode or 8k mode as set by this object.
NTF testFailTrap	1.3.6.1.4.1.2696.3.2.1.2.0.1			This trap is sent when a test which is not associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' object associated with the test to the 'fail' state from any other state. Transmission of the trap is subject to rate control and to the enable status of each test.
tr101290	1.3.6.1.4.1.2696.3.2			DVB Measurement Group MIB to support TR 101 290. This tr101290 module contains measurements defined in TR 101 290.
tr101290Cable	1.3.6.1.4.1.2696.3.2.1.7
tr101290CableSat	1.3.6.1.4.1.2696.3.2.1.6
tr101290Capability	1.3.6.1.4.1.2696.3.2.1.3
tr101290Compliances	1.3.6.1.4.1.2696.3.2.3.1
tr101290Conformance	1.3.6.1.4.1.2696.3.2.3
tr101290Control	1.3.6.1.4.1.2696.3.2.1.1
tr101290ObjectGroups	1.3.6.1.4.1.2696.3.2.3.2
tr101290Objects	1.3.6.1.4.1.2696.3.2.1
tr101290Satellite	1.3.6.1.4.1.2696.3.2.1.8
tr101290Terrestrial	1.3.6.1.4.1.2696.3.2.1.9
tr101290Trap	1.3.6.1.4.1.2696.3.2.1.2
tr101290TS	1.3.6.1.4.1.2696.3.2.1.5
trapControlEntry	1.3.6.1.4.1.2696.3.2.1.2.1.1		not-accessible	Row specification
TES trapControlFailureSummary	1.3.6.1.4.1.2696.3.2.1.2.1.1.7	TestSummary	read-only	This bit string contains a summary of all the test failures. If the bit for the test is set to one, that test is in a fail state. When a trap is being generated, the agent should ensure that this information is as up to date as possible, without causing undue delay in sending the trap.
DAT trapControlGenerationTime	1.3.6.1.4.1.2696.3.2.1.2.1.1.3	DateAndTime	accessible-for-notify	In the case of a testFailTrap or a measurementFailTrap, at the moment when the trap is generated, the value of the '...LatestError' object associated with the test which caused the trap is copied here. In the case of a measurementUnknownTrap, the time at which the measurement became unknown is copied here. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.
INP trapControlInputNumber	1.3.6.1.4.1.2696.3.2.1.2.1.1.1	InputNumber	not-accessible	Each Transport Stream input has separate trap control parameters. This object identifies the Transport Stream input to which the trap control parameters apply
NUM trapControlMeasurementValue	1.3.6.1.4.1.2696.3.2.1.2.1.1.4	FloatingPoint	accessible-for-notify	At the moment when a measurementFailTrap is generated, the value of this object is set from the '...Value' object associated with the measurement which caused the trap. Where a measurement returns multiple values, the value which is copied here is the one which is compared with the threshold(s) to generate the test result. The measurement units are the same as those of the source object. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.
OID trapControlOID	1.3.6.1.4.1.2696.3.2.1.2.1.1.2	OBJECT IDENTIFIER	accessible-for-notify	In the case of a testFailTrap or a measurementFailTrap, this object holds the OID of the '...State' or '...TestState' object whose transition to 'fail' has triggered the trap. In the case of a measurementUnknownTrap, this object holds the OID of the '...MeasurementState' object whose transition to 'unknown' has triggered the trap. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.
U32 trapControlPeriod	1.3.6.1.4.1.2696.3.2.1.2.1.1.6	Unsigned32	read-write	An agent will ensure that the interval between sending traps is no shorter than this time period. The management system can override this by setting trapControlRateStatus back to 'enabled' within the time period.
RAT trapControlRateStatus	1.3.6.1.4.1.2696.3.2.1.2.1.1.5	RateStatus	read-write	This object is used for rate control of traps, preventing overload of the management network by transmission of an excessive number of traps. The value 'disabled' means that traps are never sent. The value 'enabled' means that a trap will be sent when triggered. When a trap is sent, the agent changes the value of this object to 'enabledThrottled'. In this state the agent will not send any more traps. The agent automatically changes the value back to 'enabled' when the time specified by trapControlPeriod expires. A management application may set the value to 'enabled' at any time, but must never set the value to 'enabledThrottled'. This single status applies to all the trap types, so for example if an agent sends a testFailTrap it will not send a measurementFailTrap until the trapControlPeriod expires.
trapControlTable	1.3.6.1.4.1.2696.3.2.1.2.1		not-accessible	Table of trap control information for each input
INP trapInput	1.3.6.1.4.1.2696.3.2.1.2.2	InputNumber	accessible-for-notify	The Transport Stream input whose change triggered the current trap. This information can also be obtained by analysing the trapControlOID, but trapInput provides the information directly. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.
trapPrefix	1.3.6.1.4.1.2696.3.2.1.2.0
ACT tsConsistencyActiveTime	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.9	ActiveTime	read-only	The total time when it has been possible to perform this test
C32 tsConsistencyCounter	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.5	Counter32	read-only	Count of the number of times the consistency check has failed.
DAT tsConsistencyCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.6	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsConsistencyCounter object.
T/F tsConsistencyCounterReset	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.7	TruthValue	read-write	tsConsistencyCounter is reset to zero and tsConsistencyCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA tsConsistencyEnable	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.4	Enable	read-write	Determines whether this test and associated traps are enabled.
tsConsistencyEntry	1.3.6.1.4.1.2696.3.2.1.5.4.3.1		not-accessible	Row specification
INP tsConsistencyInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.1	InputNumber	not-accessible	Input (Transport Stream) on which the consistency check is made.
DAT tsConsistencyLatestError	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.8	DateAndTime	read-only	The timestamp at the most recent failure of the consistency check.
TES tsConsistencyState	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.3	TestState	read-only	This gives the overall pass/fail state of the consistency check.
tsConsistencyTable	1.3.6.1.4.1.2696.3.2.1.5.4.3		not-accessible	This table provides the result of the Transport Stream consistency test for each input.
IND tsConsistencyTestNumber	1.3.6.1.4.1.2696.3.2.1.5.4.3.1.2	IndexConsistencyTest	not-accessible	Specifies the consistency check test
tsMeasurements	1.3.6.1.4.1.2696.3.2.1.5.4
BIT tsMeasurePrefAllPIDBitRateElement	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.16	BitRateElement	read-write	Data unit which is counted by the bit rate measurement algorithm for PIDs. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateElement columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.
U32 tsMeasurePrefAllPIDBitRateN	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.15	Unsigned32	read-write	'N' value for PID bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateN columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.
NUM tsMeasurePrefAllPIDBitRateTau	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.14	FloatingPoint	read-write	'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateTau columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.
BIT tsMeasurePrefAllServiceBitRateElement	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.13	BitRateElement	read-write	Data unit which is counted by the bit rate measurement algorithm for services. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateElement columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.
U32 tsMeasurePrefAllServiceBitRateN	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.12	Unsigned32	read-write	'N' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateN columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.
NUM tsMeasurePrefAllServiceBitRateTau	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.11	FloatingPoint	read-write	'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateTau columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.
tsMeasurePreferences	1.3.6.1.4.1.2696.3.2.1.5.4.100
tsMeasurePreferencesEntry	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1		not-accessible	Row specification
tsMeasurePreferencesPIDEntry	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1		not-accessible	Row specification
tsMeasurePreferencesPIDTable	1.3.6.1.4.1.2696.3.2.1.5.4.100.3		not-accessible	This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual PIDs is found here.
tsMeasurePreferencesServiceEntry	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1		not-accessible	Row specification
tsMeasurePreferencesServiceTable	1.3.6.1.4.1.2696.3.2.1.5.4.100.2		not-accessible	This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual services is found here.
tsMeasurePreferencesTable	1.3.6.1.4.1.2696.3.2.1.5.4.100.1		not-accessible	This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to the whole Transport Stream is found here.
TRA tsMeasurePrefExpectedTSID	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.17	TransportStreamID	read-write	This object defines the expected Transport Stream ID that is compared with the actual ID to perform the consistency of information check.
INP tsMeasurePrefInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
NUM tsMeasurePrefPCRDemarcationFrequency	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.2	FloatingPoint	read-write	This is the demarcation frequency used by the PCR measurement system to distinguish between inaccuracy/jitter and drift.
NUM tsMeasurePrefPCRDRMax	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.4	FloatingPoint	read-write	Maximum permitted PCR_DR (drift rate). An error is indicated if the measured PCR_DR is outside the range [-tsMeasurePrefPCRDRMax .. +tsMeasurePrefPCRDRMax]
NUM tsMeasurePrefPCRFOMax	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.3	FloatingPoint	read-write	Maximum permitted PCR_FO (frequency offset). An error is indicated if the measured PCR_FO is outside the range [-tsMeasurePrefPCRFOMax .. +tsMeasurePrefPCRFOMax].
NUM tsMeasurePrefPCROJMax	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.5	FloatingPoint	read-write	Maximum permitted PCR_OJ (overall jitter). An error is indicated if the measured PCR_OJ is outside the range [-tsMeasurePrefPCROJMax .. +tsMeasurePrefPCROJMax]
BIT tsMeasurePrefPIDBitRateElement	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.6	BitRateElement	read-create	Data unit which is counted by the bit rate measurement algorithm for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID element settings, it shall ignore attempts to change the setting by writing to this object.
NUM tsMeasurePrefPIDBitRateMax	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.8	FloatingPoint	read-create	An error is generated if the PID bit rate exceeds this value.
NUM tsMeasurePrefPIDBitRateMin	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.7	FloatingPoint	read-create	An error is generated if the PID bit rate is below this value.
U32 tsMeasurePrefPIDBitRateN	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.5	Unsigned32	read-create	'N' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID 'N' settings, it shall ignore attempts to change the setting by writing to this object.
NUM tsMeasurePrefPIDBitRateTau	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.4	FloatingPoint	read-create	'tau' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID tau settings, it shall ignore attempts to change the setting by writing to this object.
INP tsMeasurePrefPIDInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
PID tsMeasurePrefPIDPID	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.2	PIDPlusOne	not-accessible	PID (plus one) to which the preferences apply.
ROW tsMeasurePrefPIDRowStatus	1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.3	RowStatus	read-create	This is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs which have a non-zero bit rate.
BIT tsMeasurePrefServiceBitRateElement	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.6	BitRateElement	read-create	Data unit which is counted by the bit rate measurement algorithm for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service element settings, it shall ignore attempts to change the setting by writing to this object.
NUM tsMeasurePrefServiceBitRateMax	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.8	FloatingPoint	read-create	An error is generated if the Transport Stream bit rate exceeds this value.
NUM tsMeasurePrefServiceBitRateMin	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.7	FloatingPoint	read-create	An error is generated if the Service bit rate is below this value.
U32 tsMeasurePrefServiceBitRateN	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.5	Unsigned32	read-create	'N' value for rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service 'N' settings, it shall ignore attempts to change the setting by writing to this object.
NUM tsMeasurePrefServiceBitRateTau	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.4	FloatingPoint	read-create	'tau' value for bit rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service tau settings, it shall ignore attempts to change the setting by writing to this object.
INP tsMeasurePrefServiceInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
ROW tsMeasurePrefServiceRowStatus	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.3	RowStatus	read-create	This is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT.
SER tsMeasurePrefServiceService	1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.2	ServiceId	not-accessible	Service to which the preferences apply.
BIT tsMeasurePrefTSBitRateElement	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.8	BitRateElement	read-write	Data unit which is counted by the bit rate measurement algorithm. See note in description for tsMeasurePrefTSBitRateTau.
NUM tsMeasurePrefTSBitRateMax	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.10	FloatingPoint	read-write	An error is generated if the Transport Stream bit rate exceeds this value.
NUM tsMeasurePrefTSBitRateMin	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.9	FloatingPoint	read-write	An error is generated if the Transport Stream bit rate is below this value.
U32 tsMeasurePrefTSBitRateN	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.7	Unsigned32	read-write	'N' value for Transport Stream bit rate measurement. See note in description for tsMeasurePrefTSBitRateTau.
NUM tsMeasurePrefTSBitRateTau	1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.6	FloatingPoint	read-write	'tau' value for Transport Stream bit rate measurement. The MIB provides very flexible ways of setting the bit rate measurement parameters tau, N and element for the Transport Stream, services, PIDs and for individual services and PIDs. Real measurement equipment can be expected to provide much less flexibility. Management software should anticipate this by either being statically aware of the capabilities of the agent or by checking that preference settings have been accepted by reading them back after each attempt to set them.
ACT tsPcrMeasurementActiveTime	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.11	ActiveTime	read-only	The total time when it has been possible to make this measurement
C32 tsPcrMeasurementCounter	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.7	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT tsPcrMeasurementCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.8	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsPcrMeasurementCounter object.
T/F tsPcrMeasurementCounterReset	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.9	TruthValue	read-create	tsPcrMeasurementCounter is reset to zero and tsPcrMeasurementCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA tsPcrMeasurementEnable	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.6	Enable	read-create	Determines whether this test and associated traps are enabled.
tsPcrMeasurementEntry	1.3.6.1.4.1.2696.3.2.1.5.4.1.1		not-accessible	Row specification
INP tsPcrMeasurementInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.1	InputNumber	not-accessible	Input on which the measurement is made
DAT tsPcrMeasurementLatestError	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.10	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA tsPcrMeasurementMeasurementState	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.12	MeasurementState	read-only	Indicates the validity of the measurement
IND tsPcrMeasurementNumber	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.3	IndexPCRMeasurement	not-accessible	This selects one of the four PCR measurements
PID tsPcrMeasurementPID	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.2	PIDPlusOne	not-accessible	PID (plus one) in the Transport Stream carrying (or expected to carry) PCRs.
ROW tsPcrMeasurementRowStatus	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.4	RowStatus	read-create	This object is used by the manager to create and delete rows in the table. The agent automatically creates rows for PIDs where it detects the presence of a PCR.
TES tsPcrMeasurementState	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.5	TestState	read-only	This gives the overall pass/fail state of the threshold test on this measurement
tsPcrMeasurementTable	1.3.6.1.4.1.2696.3.2.1.5.4.1		not-accessible	This table makes available the PCR_FO, PCR_DR, PCR_OJ and PCR_AC measurements.
NUM tsPcrMeasurementValue	1.3.6.1.4.1.2696.3.2.1.5.4.1.1.13	FloatingPoint	read-only	The units for the measured value depend on the measurement: PCR_FO Hz PCR_DR Hz/s Values for PCR_OJ and PCR_AC are not provided as they occur too quickly to be usefully retrieved via SNMP. For these measurements, the MeasurementState is always 'unknown'. However, the threshold tests are expected to work correctly for these measurements.
ACT tsPIDBitRateActiveTime	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.10	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 tsPIDBitRateCounter	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.6	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT tsPIDBitRateCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.7	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsPIDBitRateCounter object.
T/F tsPIDBitRateCounterReset	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.8	TruthValue	read-create	tsPIDBitRateCounter is reset to zero and tsPIDBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA tsPIDBitRateEnable	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.5	Enable	read-create	Determines whether the threshold test and associated traps for this measurement are enabled.
tsPIDBitRateEntry	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1		not-accessible	Row specification
INP tsPIDBitRateInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT tsPIDBitRateLatestError	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.9	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA tsPIDBitRateMeasurementState	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.11	MeasurementState	read-only	Indicates the validity of the measurement
STR tsPIDBitRateNomenclature	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.13	DisplayString	read-only	Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2'
PID tsPIDBitRatePID	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.2	PIDPlusOne	not-accessible	PID whose bit rate is being measured (plus one)
ROW tsPIDBitRateRowStatus	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.3	RowStatus	read-create	This is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs whose bit rate is non-zero.
TES tsPIDBitRateState	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.4	TestState	read-only	This gives the overall pass/fail state of the threshold test on this measurement
tsPIDBitRateTable	1.3.6.1.4.1.2696.3.2.1.5.4.2.3		not-accessible	Bit rates for each PID within each Transport Stream. The table is sparse, in that only PIDs whose bit rate is currently greater than zero will be present in the table. This allows for faster traversal of the table to build up a list of PID bit rates.
NUM tsPIDBitRateValue	1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.12	FloatingPoint	read-only	Bit rate for the PID.
ACT tsServiceBitRateActiveTime	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.10	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 tsServiceBitRateCounter	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.6	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT tsServiceBitRateCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.7	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsServiceBitRateCounter object.
T/F tsServiceBitRateCounterReset	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.8	TruthValue	read-create	tsServiceBitRateCounter is reset to zero and tsServiceBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA tsServiceBitRateEnable	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.5	Enable	read-create	Determines whether the threshold test and associated traps for this measurement are enabled.
tsServiceBitRateEntry	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1		not-accessible	Row specification
INP tsServiceBitRateInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT tsServiceBitRateLatestError	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.9	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA tsServiceBitRateMeasurementState	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.11	MeasurementState	read-only	Indicates the validity of the measurement
STR tsServiceBitRateNomenclature	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.13	DisplayString	read-only	Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2'
ROW tsServiceBitRateRowStatus	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.3	RowStatus	read-create	This is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT.
SER tsServiceBitRateService	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.2	ServiceId	not-accessible	The program_number/service_id to which the information in the rest of the row applies.
TES tsServiceBitRateState	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.4	TestState	read-only	This gives the overall pass/fail state of the threshold test on this measurement
tsServiceBitRateTable	1.3.6.1.4.1.2696.3.2.1.5.4.2.2		not-accessible	Bit rates for each service/program within each Transport Stream. The table is sparse, in that only services mentioned in the PMT will be present. The bit rate of a service is the sum of the bit rates of the elementary_PID's in its PMT and the CA_PID's in any CA_descriptors in its PMT (ECMs). The bit rate of the PMT itself is excluded. The bit rate of the PCR_PID is excluded unless the PCR_PID is also one of the elementary_PID's in the PMT.
NUM tsServiceBitRateValue	1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.12	FloatingPoint	read-only	Overall bit rate for the service
tsServicePerformance	1.3.6.1.4.1.2696.3.2.1.5.5
ACT tsServicePerformanceActiveTime	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.9	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 tsServicePerformanceCounter	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.5	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT tsServicePerformanceCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.6	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsServicePerformanceCounter object.
T/F tsServicePerformanceCounterReset	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.7	TruthValue	read-write	tsServicePerformanceCounter is reset to zero and tsServicePerformanceCounterDiscontinuity is set to the current time if 'true' is written to this variable. The value read from this object is always 'false'.
ENA tsServicePerformanceEnable	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.4	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
tsServicePerformanceEntry	1.3.6.1.4.1.2696.3.2.1.5.5.2.1		not-accessible	Row specification
U32 tsServicePerformanceError	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.11	Unsigned32	read-only	The calculated xxx_Error parameter as measured at the end of the most recently completed DeltaT period.
NUM tsServicePerformanceErrorRatio	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.12	FloatingPoint	read-only	This is the calculated xxx_Error_Ratio as a percentage (e.g. '1.32'). The value is for the most recently completed evaluation time (e.g. 10 minutes).
INP tsServicePerformanceInputNumber	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT tsServicePerformanceLatestError	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.8	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA tsServicePerformanceMeasurementState	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.10	MeasurementState	read-only	Indicates the validity of the measurement
IND tsServicePerformanceNumber	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.2	IndexServicePerformance	not-accessible	The Service Performance measurement which this row applies to.
tsServicePerformancePreferencesEntry	1.3.6.1.4.1.2696.3.2.1.5.5.100.1		not-accessible	Row specification
tsServicePerformancePreferencesTable	1.3.6.1.4.1.2696.3.2.1.5.5.100		not-accessible	Parameters controlling the Service Performance measurements
TES tsServicePerformanceState	1.3.6.1.4.1.2696.3.2.1.5.5.2.1.3	TestState	read-only	This gives the overall pass/fail state of the threshold test on this measurement. The threshold test fails if the value of tsServicePerformanceErrorRatio exceeds the value given in the preferences.
tsServicePerformanceTable	1.3.6.1.4.1.2696.3.2.1.5.5.2		not-accessible	This table gives access to the Service Performance measurements and tests
NUM tsSPPrefDeltaT	1.3.6.1.4.1.2696.3.2.1.5.5.100.1.3	FloatingPoint	read-write	The defined time interval over which errors are counted
NUM tsSPPrefEvaluationTime	1.3.6.1.4.1.2696.3.2.1.5.5.100.1.4	FloatingPoint	read-write	The period over which the ...Error_Ratio is calculated
INP tsSPPrefInputNumber	1.3.6.1.4.1.2696.3.2.1.5.5.100.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
IND tsSPPrefNumber	1.3.6.1.4.1.2696.3.2.1.5.5.100.1.2	IndexServicePerformance	not-accessible	The service performance parameter to which these preferences apply.
NUM tsSPPrefThreshold	1.3.6.1.4.1.2696.3.2.1.5.5.100.1.5	FloatingPoint	read-write	The threshold value used in calculating the ..._Error_Ratio.
tsTests	1.3.6.1.4.1.2696.3.2.1.5.2
ACT tsTestsPIDActiveTime	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.11	ActiveTime	read-only	The total time when it has been possible to evaluate this test.
C32 tsTestsPIDCounter	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.7	Counter32	read-only	Count of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other state. For Error events this is the total number of events; the persistence timer is not taken into account by the counter.
DAT tsTestsPIDCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.8	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsTestsSummaryCounter object.
T/F tsTestsPIDCounterReset	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.9	TruthValue	read-create	tsTestsPIDCounter is reset to zero and tsTestsPIDCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA tsTestsPIDEnable	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.6	Enable	read-create	Determines whether this test and associated traps are enabled. When a trap triggering condition arises for a per PID test, this object alone is used to determine whether a trap will be generated, without any reference to tsTestsSummaryEnable.
tsTestsPIDEntry	1.3.6.1.4.1.2696.3.2.1.5.2.3.1		not-accessible	Row specification
INP tsTestsPIDInputNumber	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.1	InputNumber	not-accessible	Transport Stream on which the test is made
DAT tsTestsPIDLatestError	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.10	DateAndTime	read-only	The timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other state. For Error events this is the most recent occurrence; the persistence timer is not taken into account.
PID tsTestsPIDPID	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.2	PIDPlusOne	not-accessible	PID (plus one) on which the test is made
ROW tsTestsPIDRowStatus	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.4	RowStatus	read-create	This is used by the manager to create and delete rows in tsTestsPIDTable. The agent automatically creates rows for PID/test combinations where there are errors to report.
TES tsTestsPIDState	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.5	TestState	read-only	This gives the overall pass/fail state of the test
tsTestsPIDTable	1.3.6.1.4.1.2696.3.2.1.5.2.3		not-accessible	The tsTestsPIDTable provides access to the state of those Transport Stream tests enumerated in IndexTransportStreamTest which relate to individual PIDs. These tests are: 1.4 Continuity_count_error 1.5.a PMT_error_2 1.6 PID_error 2.3.a PCR_repetition_error 2.3.b PCR_discontinuity_indicator_error 2.4 PCR_accuracy_error 2.5 PTS_error 3.3 Buffer_error 3.4.a Unreferenced_PID
IND tsTestsPIDTestNumber	1.3.6.1.4.1.2696.3.2.1.5.2.3.1.3	IndexTransportStreamTest	not-accessible	Specifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipment.
NUM tsTestsPrefBATTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.15	FloatingPoint	read-write	Maximum permitted BAT table repetition interval
NUM tsTestsPrefEITActualIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.28	FloatingPoint	read-write	Maximum permitted EIT_actual section repetition interval (applies to both present and following sections).
NUM tsTestsPrefEITActualIntervalMin	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.29	FloatingPoint	read-write	Minimum permitted EIT_actual section repetition interval
NUM tsTestsPrefEITOtherIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.30	FloatingPoint	read-write	Maximum permitted EIT_other section repetition interval (applies to both present and following sections).
NUM tsTestsPrefEITPFActualTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.18	FloatingPoint	read-write	Maximum permitted EIT Present/Following actual transport stream table repetition interval
NUM tsTestsPrefEITPFOtherTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.19	FloatingPoint	read-write	Maximum permitted EIT Present/Following other transport stream table repetition interval
NUM tsTestsPrefEITSActualFarTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.21	FloatingPoint	read-write	Maximum permitted EIT Schedule actual transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the next day for terrestrial).
NUM tsTestsPrefEITSActualNearTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.20	FloatingPoint	read-write	Maximum permitted EIT Schedule actual transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for terrestrial).
NUM tsTestsPrefEITSOtherFarTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.23	FloatingPoint	read-write	Maximum permitted EIT Schedule other transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the next day for terrestrial).
NUM tsTestsPrefEITSOtherNearTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.22	FloatingPoint	read-write	Maximum permitted EIT Schedule other transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for terrestrial).
tsTestsPreferences	1.3.6.1.4.1.2696.3.2.1.5.2.100
tsTestsPreferencesEntry	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1		not-accessible	Row specification
tsTestsPreferencesPIDEntry	1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1		not-accessible	Description.
tsTestsPreferencesPIDTable	1.3.6.1.4.1.2696.3.2.1.5.2.100.2		not-accessible	This table contains measurement thresholds and other configuration information that is applied on a per PID per Transport Stream basis.
tsTestsPreferencesTable	1.3.6.1.4.1.2696.3.2.1.5.2.100.1		not-accessible	This table contains measurement thresholds and other configuration information that is applied on a per Transport Stream basis.
INP tsTestsPrefInputNumber	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
NUM tsTestsPrefNITActualIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.10	FloatingPoint	read-write	Maximum permitted NIT_actual section repetition interval
NUM tsTestsPrefNITActualIntervalMin	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.11	FloatingPoint	read-write	Minimum permitted NIT_actual section repetition interval
NUM tsTestsPrefNITOtherIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.12	FloatingPoint	read-write	Maximum permitted NIT_other section repetition interval
NUM tsTestsPrefNITTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.14	FloatingPoint	read-write	Maximum permitted NIT table repetition interval
NUM tsTestsPrefPATSectionIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.3	FloatingPoint	read-write	Maximum repetition interval for PAT sections.
NUM tsTestsPrefPCRDiscontinuityMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.7	FloatingPoint	read-write	Maximum permitted difference between two consecutive PCR values.
NUM tsTestsPrefPCRInaccuracyMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.8	FloatingPoint	read-write	Maximum permitted PCR inaccuracy. An error is indicated if the PCR inaccuracy is outside the range: [-tsTestsPrefPCRInaccuracyMax .. +tsTestsPrefPCRInaccuracyMax].
NUM tsTestsPrefPCRIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.6	FloatingPoint	read-write	Maximum permitted interval between PCR arrival times on each PCR PID.
INP tsTestsPrefPIDInputNumber	1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.1	InputNumber	not-accessible	Transport Stream input to which the preferences apply
PID tsTestsPrefPIDPID	1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.2	PIDPlusOne	not-accessible	PID to which these preferences apply
NUM tsTestsPrefPIDReferredIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.4	FloatingPoint	read-write	Maximum permitted interval between the arrival of consecutive packets of this PID. The default value for this object is the current value of tsTestsPrefReferredIntervalMax for the same input.
ROW tsTestsPrefPIDRowStatus	1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.3	RowStatus	read-create	This object is used to manage the rows in this table.
NUM tsTestsPrefPMTSectionIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.4	FloatingPoint	read-write	Maximum repetition interval for PMT sections.
NUM tsTestsPrefPTSIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.9	FloatingPoint	read-write	Maximum permitted PTS repetition interval
NUM tsTestsPrefReferredIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.5	FloatingPoint	read-write	Maximum permitted interval between the arrival of consecutive packets for all PIDs. When the value of this object is set, the value of tsTestsPrefPIDReferredIntervalMax is changed for every PID. The value of this object is also used as a default for tsTestsPrefPIDReferredIntervalMax when a new row is created in tsTestsPreferencesPIDTable.
NUM tsTestsPrefRSTIntervalMin	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.31	FloatingPoint	read-write	Minimum permitted RST section repetition interval
NUM tsTestsPrefSDTActualIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.25	FloatingPoint	read-write	Maximum permitted SDT_actual section repetition interval
NUM tsTestsPrefSDTActualIntervalMin	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.26	FloatingPoint	read-write	Minimum permitted SDT_actual section repetition interval
NUM tsTestsPrefSDTActualTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.16	FloatingPoint	read-write	Maximum permitted SDT actual transport stream table repetition interval
NUM tsTestsPrefSDTOtherIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.27	FloatingPoint	read-write	Maximum permitted SDT_other section repetition interval
NUM tsTestsPrefSDTOtherTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.17	FloatingPoint	read-write	Maximum permitted SDT other transport stream table repetition interval
NUM tsTestsPrefSIGapMin	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.13	FloatingPoint	read-write	Minimum permitted gap between packets containing sections.
NUM tsTestsPrefTDTIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.32	FloatingPoint	read-write	Maximum permitted TDT section repetition interval
NUM tsTestsPrefTDTIntervalMin	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.33	FloatingPoint	read-write	Minimum permitted TDT section repetition interval
NUM tsTestsPrefTransitionDuration	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.2	FloatingPoint	read-write	Various tests, including CAT_error (2.6) and Unreferenced_PID (3.4) must take into account that short transition periods can exist where the state of the SI and PSI information is inconsistent with the state of the stream. These transitions should not cause error indications. This parameter specifies the period which must be allowed for transition states.
NUM tsTestsPrefTxTTableIntervalMax	1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.24	FloatingPoint	read-write	Maximum permitted TDT and TOT table repetition intervals
ACT tsTestsSummaryActiveTime	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.9	ActiveTime	read-only	The total time when it has been possible to evaluate this test.
C32 tsTestsSummaryCounterEx	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.5	Counter32	read-only	Count of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other state. For Error events this is the total number of events; the persistence timer is not taken into account by the counter.
DAT tsTestsSummaryCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.6	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsTestsSummaryCounter object.
T/F tsTestsSummaryCounterReset	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.7	TruthValue	read-write	tsTestsSummaryCounter is reset to zero and tsTestsSummaryCounterDiscontinuity is set to the current time if this object is set to 'true'. This object has no effect on the tsTestsPIDCounter objects.
ENA tsTestsSummaryEnable	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.4	Enable	read-write	Determines whether this test and associated traps are enabled. Setting tsTestsSummaryEnable affects tsTestsPIDEnable in tsTestsPIDTable. When tsTestsSummaryEnable is set, all existing instances of tsTestsPIDEnable are set to the same value. Any new rows in tsTestsPIDTable which are created will also have this value for tsTestsPIDEnable (unless the row is created by explicitly setting the value of tsTestsPIDEnable).
tsTestsSummaryEntry	1.3.6.1.4.1.2696.3.2.1.5.2.2.1		not-accessible	Row specification
INP tsTestsSummaryInputNumber	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.1	InputNumber	not-accessible	Transport Stream on which the test is made
DAT tsTestsSummaryLatestError	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.8	DateAndTime	read-only	The timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other state. For Error events this is the most recent occurrence; the persistence timer is not taken into account.
TES tsTestsSummaryState	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.3	TestState	read-only	This gives the overall pass/fail state of the test. For tests which have a state per PID, tsTestsSummaryState contains the highest numeric value of all the tsTestsPIDState objects for the test.
tsTestsSummaryTable	1.3.6.1.4.1.2696.3.2.1.5.2.2		not-accessible	The tsTestsSummaryTable provides access to the state of all of the Transport Stream tests enumerated in IndexTransportStreamTest. The status relates to the whole Transport Stream. In the case of tests which have a status per PID, the tsTestsSummaryTable gives the 'worst' status across all the PIDs and the status for each PID is available in tsTestsPIDTable.
IND tsTestsSummaryTestNumber	1.3.6.1.4.1.2696.3.2.1.5.2.2.1.2	IndexTransportStreamTest	not-accessible	Specifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipment.
ACT tsTransportStreamBitRateActiveTime	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.8	ActiveTime	read-only	The total time when it has been possible to perform this measurement
C32 tsTransportStreamBitRateCounter	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.4	Counter32	read-only	Count of the number of times a threshold error has occurred for this measurement.
DAT tsTransportStreamBitRateCounterDiscontinuity	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.5	DateAndTime	read-only	Provides the last time at which there was a discontinuity in the tsTransportStreamBitRateCounterobject.
T/F tsTransportStreamBitRateCounterReset	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.6	TruthValue	read-write	tsTransportStreamBitRateCounteris reset to zero and tsTransportStreamBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.
ENA tsTransportStreamBitRateEnable	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.3	Enable	read-write	Determines whether the threshold test and associated traps for this measurement are enabled.
tsTransportStreamBitRateEntry	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1		not-accessible	Row specification
INP tsTransportStreamBitRateInputNumber	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.1	InputNumber	not-accessible	Transport Stream on which the measurement is made
DAT tsTransportStreamBitRateLatestError	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.7	DateAndTime	read-only	The timestamp at the most recent occurrence of a threshold error on this measurement.
MEA tsTransportStreamBitRateMeasurementState	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.9	MeasurementState	read-only	Indicates the validity of the measurement
STR tsTransportStreamBitRateNomenclature	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.11	DisplayString	read-only	Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2'
TES tsTransportStreamBitRateState	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.2	TestState	read-only	This gives the overall pass/fail state of the threshold test on this measurement
tsTransportStreamBitRateTable	1.3.6.1.4.1.2696.3.2.1.5.4.2.1		not-accessible	Bit rates for each complete Transport Stream
NUM tsTransportStreamBitRateValue	1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.10	FloatingPoint	read-only	The overall Transport Stream bit rate

RFC description

Digital Video Broadcasting measurement MIB for TR 101 290 compliance testing and video signal quality monitoring.

Start monitoring DVB transport-stream analyzer/monitoring probe (vendor-neutral ETSI TR 101 290 standard) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DVB-MGTR101290-MIB