All MIBs › DS8200v2-MIB
Organization: Verilink Corporation
Last Updated: 2000-08-18
Category: Domain: WAN
Description:
Manages DS8200 version 2 series digital switching system configuration and operational status.
Imported Objects
From DS8200v2-TC-MIB
| hbu | OBJECT-IDENTITY |
| verilink | MODULE-IDENTITY |
From SNMPv2-SMI
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| enterprises |
From SNMPv2-TC
| DisplayString |
What Is DS8200v2-MIB?
DS8200v2-MIB is a vendor MIB for the DS8200 version 2 digital switching/transport system, exposing product identification and hardware inventory objects alongside management-port and interface-technology (T1/E1) branches. It provides objects for model number and description, element ID, serial number, physical and NMS-facing addresses, and per-slot label information via a label table, together with software and hardware revision fields. Its monitoring value centers on hardware/software identification and inventory status: productSoftwareRev and productHardwareRev let an operator confirm firmware and hardware revisions across a deployed base, productSerialNum and productElementId support asset tracking, and the mgmtPorts/dbu/t1e1 branches point to line-level status for management and T1/E1 transport interfaces. As a self-contained product MIB it does not appear to lean on IETF standard MIBs beyond basic SNMP conventions. It is typically deployed on DS8200v2 digital switching/multiplexing equipment in telecom transport network sites. Engineers can download the DS8200v2-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DS8200v2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
What Can Be Monitored
- product model/serial identification
- software and hardware revision
- slot/card label information
- T1/E1 interface status
- management port status
Supported Devices
- digital switching/transport multiplexer (DS8200v2 series)
Monitoring Examples
An administrator would poll productModelNumber, productSerialNum, and productSoftwareRev/productHardwareRev to inventory and verify the revision level of deployed DS8200v2 units across a network. The productLabelTable/productLabelTableEntry, keyed by labelTableIndex, would be checked for labelTableLabel to identify which physical card or port slot a given entry corresponds to. The t1e1 and dbu branches would be polled for T1/E1 line and distribution-bus status to catch a transport-facing circuit fault on the unit.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tinterfaces | 1.3.6.1.4.1.321.100.2 | DS8200v2 MIB. | ||
| mgmtPorts | 1.3.6.1.4.1.321.100.2.1 | |||
| mgmtPortsTable | 1.3.6.1.4.1.321.100.2.1.1 | not-accessible | The Management Ports table. | |
| mgmtPortsTableEntry | 1.3.6.1.4.1.321.100.2.1.1.1 | not-accessible | An entry in the Management Ports table. | |
| INT mgmtPortsTableIndex | 1.3.6.1.4.1.321.100.2.1.1.1.1 | INTEGER | read-only | The index into the Management Ports table. |
| STR mgmtPortsDescription | 1.3.6.1.4.1.321.100.2.1.1.1.2 | DisplayString | read-only | Contains a textual description of the port. |
| STR mgmtPortsElementID | 1.3.6.1.4.1.321.100.2.1.1.1.3 | DisplayString | read-write | This object signifies the name of the device. |
| INT mgmtPortsMode | 1.3.6.1.4.1.321.100.2.1.1.1.4 | INTEGER | read-write | This object signifies the method used by the port to report alarms. |
| STR mgmtPortsDialPrefix | 1.3.6.1.4.1.321.100.2.1.1.1.5 | DisplayString | read-write | This object contains the dial string prefix for a modem connected to the port. |
| STR mgmtPortsPrimaryDialString | 1.3.6.1.4.1.321.100.2.1.1.1.6 | DisplayString | read-write | This object contains the primary dial string for a modem connected to the port. |
| STR mgmtPortsSecondaryDialString | 1.3.6.1.4.1.321.100.2.1.1.1.7 | DisplayString | read-write | This object contains the secondary dial string for a modem connected to the port. |
| STR mgmtPortsExtInitString | 1.3.6.1.4.1.321.100.2.1.1.1.8 | DisplayString | read-write | This object contains the init string for a modem connected to the port. |
| INT mgmtPortsCompressedSlip | 1.3.6.1.4.1.321.100.2.1.1.1.9 | INTEGER | read-write | This object specifies if SLIP compression is to be used. |
| INT mgmtPortsInternalModem | 1.3.6.1.4.1.321.100.2.1.1.1.10 | INTEGER | read-write | This object signifies if the internal modem (when present) is enabled. |
| dbu | 1.3.6.1.4.1.321.100.2.2 | |||
| dbuConfigTable | 1.3.6.1.4.1.321.100.2.2.1 | not-accessible | The Dial Backup Configuration Table. | |
| dbuConfigTableEntry | 1.3.6.1.4.1.321.100.2.2.1.1 | not-accessible | An entry in the Dial Backup Configuration table. | |
| INT dbuNearIndex | 1.3.6.1.4.1.321.100.2.2.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT dbuFarIndex | 1.3.6.1.4.1.321.100.2.2.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT dbuConfigTableIndex | 1.3.6.1.4.1.321.100.2.2.1.1.3 | INTEGER | read-only | The index into the Dial Backup table. |
| STR dbuDescription | 1.3.6.1.4.1.321.100.2.2.1.1.4 | DisplayString | read-only | Contains a textual description of the dbu. |
| INT dbuRate | 1.3.6.1.4.1.321.100.2.2.1.1.5 | INTEGER | read-write | This object is the identifier of the current DDS DBU rate. The values mean: dbuRate2400 the DBU interface is operating at 2400bps dbuRate4800 the DBU interface is operating at 4800bps dbuRate9600 the DBU interface is operating at 9600bps dbuRate19200 the DBU interface is operating at 19200bps dbuRate38400 the DBU interface is operating at 38400bps dbuRate56000 the DBU interface is operating at 56000bps dbuRate57600 the DBU interface is operating at 57600bps dbuRate64000 the DBU interface is operating at 64000bps |
| INT dbuMode | 1.3.6.1.4.1.321.100.2.2.1.1.6 | INTEGER | read-write | This object is the identifier of the current mode that the Dial Backup Unit is operating in. The values mean: dbuModeOrig The dial backup unit is operating in the originate mode dbuModeAnsw The dial backup unit is operating in the answer mode dbuModeNotAvail The dial backup unit's mode is not available dbuModeCallbackOrig The dial backup unit is operating in the callback originate mode dbuModeCallbackAnsw The dial backup unit is operating in the callback mode dbuModeMaster The dial backup unit is configured as a master unit dbuModeSlave The dial backup unit is configured as a slave unit |
| INT dbuFormat | 1.3.6.1.4.1.321.100.2.2.1.1.7 | INTEGER | read-write | This object is the identifier of the current format that the Dial Backup Unit is operating in. The values mean: dbuFormatSync The dial backup unit is operating in the synchronous format dbuFormatAsync The dial backup unit is operating in the asynchronous format dbuFormatNotAvail The dial backup unit's format is not available |
| STR dbuNumber | 1.3.6.1.4.1.321.100.2.2.1.1.8 | DisplayString | read-write | This string is the currently programmed number for the dial backup unit to call |
| INT dbuStatus | 1.3.6.1.4.1.321.100.2.2.1.1.9 | INTEGER | read-only | This object is the identifier of the current Dial Backup Unit operating status. The values mean: dbuStatusDisabled The dial backup unit is either not installed or disabled dbuStatusEnabled The dial backup unit is installed and enabled dbuStatusActive The dial backup unit is currently active dbuStatusLocked The dial backup unit is in a locked state dbuStatusConnecting The dial backup unit is in the process of connecting dbuStatusDisallowed The dial backup unit is currently not allowed to activate due to the Time Of Day Enable settings dbuStatusAwaitingCall The dial backup unit is in the process of waiting for an incoming call dbuStatusDialing The dial backup unit is in the process of placing a call dbuStatusDisconnecting The dial backup unit is in the process of disconnecting dbuStatusTesting The dial backup unit is in the process of testing dbuStatusTestPassed The dial backup unit has passed a self-test dbuStatusTestFailed The dial backup unit has failed a self-test |
| INT dbuCommand | 1.3.6.1.4.1.321.100.2.2.1.1.10 | INTEGER | read-write | This object is the identifier of the current setting that the Dial Backup Unit is operating in. The values mean: dbuCommandDisable The dial backup unit is not to operate dbuCommandEnable The dial backup unit is to operate, subject to Activator and line conditions only dbuCommandActivate The dial backup unit is to operate, irregardless of line conditions dbuCommandLock The dial backup unit is to continue operating, irregardless of line conditions dbuCommandEnableDaily The dial backup unit is to operate, subject to Activator, line conditions, and the Time Of Day Enable fields dbuCommandTest The dial backup unit is commanded to test the link. |
| INT dbuActivator1 | 1.3.6.1.4.1.321.100.2.2.1.1.11 | INTEGER | read-write | This object is the identifier of the current trigger that will activate the Dial Backup Unit. The values mean: dbuActivatorLOS The dial backup unit is activated by a LOS alarm condition dbuActivatorOOS The dial backup unit is activated by an OOS alarm condition dbuActivatorOOF The dial backup unit is activated by an OOF alarm condition dbuActivatorAny The dial backup unit is activated by a LOS, OOS, or OOF alarm condition dbuActivatorES The dial backup unit is activated by an ES alarm condition dbuActivatorSES The dial backup unit is activated by an SES alarm condition dbuActivatorUAS The dial backup unit is activated by an UAS alarm condition dbuActivatorLOF The dial backup unit is activated by an LOF alarm condition dbuActivatorRAS The dial backup unit is activated by an RAS alarm condition dbuActivatorAIS The dial backup unit is activated by an AIS alarm condition dbuActivatorBPV The dial backup unit is activated by an BPV alarm condition |
| INT dbuActivator2 | 1.3.6.1.4.1.321.100.2.2.1.1.12 | INTEGER | read-write | This object is the identifier of the current trigger that will activate the Dial Backup Unit. The values mean: dbuActivatorLOS The dial backup unit is activated by a LOS alarm condition dbuActivatorOOS The dial backup unit is activated by a OOS alarm condition dbuActivatorOOF The dial backup unit is activated by a OOF alarm condition dbuActivatorAny The dial backup unit is activated by a LOS, OOS, or OOF alarm condition dbuActivatorES The dial backup unit is activated by an ES alarm condition dbuActivatorSES The dial backup unit is activated by an SES alarm condition dbuActivatorUAS The dial backup unit is activated by an UAS alarm condition dbuActivatorLOF The dial backup unit is activated by an LOF alarm condition dbuActivatorRAS The dial backup unit is activated by an RAS alarm condition dbuActivatorAIS The dial backup unit is activated by an AIS alarm condition dbuActivatorBPV The dial backup unit is activated by an BPV alarm condition |
| STR dbuDialStr | 1.3.6.1.4.1.321.100.2.2.1.1.13 | DisplayString | read-write | This string is the dial string sent to the dial backup unit during every connection attempt |
| STR dbuInitStr | 1.3.6.1.4.1.321.100.2.2.1.1.14 | DisplayString | read-write | This string is the initialization string sent to the dial backup unit before every connection attempt |
| STR dbuHangupStr | 1.3.6.1.4.1.321.100.2.2.1.1.15 | DisplayString | read-write | This string is the hangup command string sent to the dial backup unit after every successful call |
| STR dbuPasswordStr | 1.3.6.1.4.1.321.100.2.2.1.1.16 | DisplayString | read-write | This string is the prompt character and password string for the dial backup unit in Callback DBU |
| INT dbuSecurity | 1.3.6.1.4.1.321.100.2.2.1.1.17 | INTEGER | read-write | Enables security on dial backup unit. |
| INT dbuDtrDial | 1.3.6.1.4.1.321.100.2.2.1.1.18 | INTEGER | read-write | Enables DTR dial feature on dial backup unit. |
| INT dbuISDNSwitchType | 1.3.6.1.4.1.321.100.2.2.1.1.19 | INTEGER | read-write | Specifies the switch type for the ISDN DBU. |
| INT dbuISDNSwitchVersion | 1.3.6.1.4.1.321.100.2.2.1.1.20 | INTEGER | read-write | Specifies the switch version for the ISDN DBU. |
| INT dbuISDNTEI | 1.3.6.1.4.1.321.100.2.2.1.1.21 | INTEGER | read-write | Specifies the ISDN DBU TEI. |
| STR dbuISDNSPID | 1.3.6.1.4.1.321.100.2.2.1.1.22 | DisplayString | read-write | Specifies the SPID for the ISDN DBU. |
| STR dbuISDNDDNUM | 1.3.6.1.4.1.321.100.2.2.1.1.23 | DisplayString | read-write | Specifies the Data Directory Number for the ISDN DBU. |
| dbuResetStringsTable | 1.3.6.1.4.1.321.100.2.2.2 | not-accessible | A table of COLD START reprogramming strings for the dial backup unit. | |
| dbuResetStringsEntry | 1.3.6.1.4.1.321.100.2.2.2.1 | not-accessible | An entry in the dbuResetStringsTable. | |
| INT dbuResetNearIndex | 1.3.6.1.4.1.321.100.2.2.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT dbuResetFarIndex | 1.3.6.1.4.1.321.100.2.2.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT dbuResetConfigEntryIndex | 1.3.6.1.4.1.321.100.2.2.2.1.3 | INTEGER | read-only | The index into the Dial Backup table. |
| INT dbuResetStringsIndex | 1.3.6.1.4.1.321.100.2.2.2.1.4 | INTEGER | read-only | The index into the dbuResetStringsTable. |
| STR dbuResetString | 1.3.6.1.4.1.321.100.2.2.2.1.5 | DisplayString | read-write | This string is one of the dial backup unit's COLD START reprogramming strings |
| dbuStartStopTable | 1.3.6.1.4.1.321.100.2.2.3 | not-accessible | The Dial Backup StartStop Table. | |
| dbuStartStopTableEntry | 1.3.6.1.4.1.321.100.2.2.3.1 | not-accessible | An entry in the Dial Backup Start Stop table. | |
| INT dbuStartStopNearIndex | 1.3.6.1.4.1.321.100.2.2.3.1.1 | INTEGER | read-only | Selects the near device. |
| INT dbuStartStopFarIndex | 1.3.6.1.4.1.321.100.2.2.3.1.2 | INTEGER | read-only | Selects the far device. |
| INT dbuStartStopConfigEntryIndex | 1.3.6.1.4.1.321.100.2.2.3.1.3 | INTEGER | read-only | The index into the Dial Backup table. |
| INT dbuStartStopDayOfWeek | 1.3.6.1.4.1.321.100.2.2.3.1.4 | INTEGER | read-only | The index into the Dial Backup Start Stop times table. |
| INT dbuStart | 1.3.6.1.4.1.321.100.2.2.3.1.5 | INTEGER | read-write | This object is the beginning of an allowable window for Dial Backup Activation. |
| INT dbuStop | 1.3.6.1.4.1.321.100.2.2.3.1.6 | INTEGER | read-write | This object is the end of an allowable window for Dial Backup Activation. |
| t1e1 | 1.3.6.1.4.1.321.100.2.3 | |||
| t1e1ConfigTable | 1.3.6.1.4.1.321.100.2.3.1 | not-accessible | The T1 and E1 Configuration Table. | |
| t1e1ConfigTableEntry | 1.3.6.1.4.1.321.100.2.3.1.1 | not-accessible | An entry in the t1e1Table. | |
| INT t1e1ConfigNearIndex | 1.3.6.1.4.1.321.100.2.3.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT t1e1ConfigFarIndex | 1.3.6.1.4.1.321.100.2.3.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT t1e1ConfigIndex | 1.3.6.1.4.1.321.100.2.3.1.1.3 | INTEGER | read-only | This object is the index into the t1e1Table. |
| STR t1e1Description | 1.3.6.1.4.1.321.100.2.3.1.1.4 | DisplayString | read-only | Contains a textual description of the port. |
| INT t1e1Mode | 1.3.6.1.4.1.321.100.2.3.1.1.5 | INTEGER | read-write | This object identifies the port as either a Network (long-haul) or DTE (short-haul) port. |
| INT t1e1FrameType | 1.3.6.1.4.1.321.100.2.3.1.1.6 | INTEGER | read-write | Selects the framing for the network side of the DSU/CSU. |
| INT t1e1LineCode | 1.3.6.1.4.1.321.100.2.3.1.1.7 | INTEGER | read-write | Selects the network side line coding. |
| INT t1e1LineBuildOut | 1.3.6.1.4.1.321.100.2.3.1.1.8 | INTEGER | read-write | Selects the line build out for the network interface. The options are: t1e1LineBuildOut0db indicates a line build out of 0db t1e1LineBuildOut75db indicates a line build out of -7.5db t1e1LineBuildOut15db indicates a line build out of -15db t1e1LineBuildOut225db indicates a line build out of -22.5db |
| INT t1e1Timing | 1.3.6.1.4.1.321.100.2.3.1.1.9 | INTEGER | read-write | Sets the timing source to synchronize the unit's internal timing generators. |
| INT t1e1StationInTiming | 1.3.6.1.4.1.321.100.2.3.1.1.10 | INTEGER | read-write | Selects the input timing if t1e1Timing is set to Station. |
| INT t1e1StationTiming | 1.3.6.1.4.1.321.100.2.3.1.1.11 | INTEGER | read-write | Selects the N-multiple when Station Input Timing is set to either NX56 or NX65. The N range is 1..24 |
| INT t1e1PRM | 1.3.6.1.4.1.321.100.2.3.1.1.12 | INTEGER | read-write | Enables the ANSI T1.403 Performance Report Message functions. |
| INT t1e1ZeroSuppress | 1.3.6.1.4.1.321.100.2.3.1.1.13 | INTEGER | read-write | Determines whether ones density insertion is activated after 15 zeros . To ensure compliance with TR54016, this field must be enabled. |
| INT t1e1NationalBit | 1.3.6.1.4.1.321.100.2.3.1.1.14 | INTEGER | read-write | Selects a national bit to create a 4-kbps datalink between the endpoint units. |
| INT t1e1KeepAlive | 1.3.6.1.4.1.321.100.2.3.1.1.15 | INTEGER | read-write | Selects keep alive framed and unframed ones when the unit detects LOS or OOF. |
| INT t1e1CRC4Mode | 1.3.6.1.4.1.321.100.2.3.1.1.16 | INTEGER | read-write | Selects whether CRC4 is enabled or disabled. |
| INT t1e1DSXLevel | 1.3.6.1.4.1.321.100.2.3.1.1.17 | INTEGER | read-write | Selects the DSX1 interface output level. |
| INT t1e1CRC | 1.3.6.1.4.1.321.100.2.3.1.1.18 | INTEGER | read-write | Determines whether received CRC data is passed through or regenerated. |
| INT t1e1FDLPassThrough | 1.3.6.1.4.1.321.100.2.3.1.1.19 | INTEGER | read-write | Determines whether the ESF FDL passes through the CSU or terminates. |
| INT t1e1AudibleAlarm | 1.3.6.1.4.1.321.100.2.3.1.1.20 | INTEGER | read-write | If applicable, Enables or Disables the CSU's internal buzzer which alerts users of an alarm condition. |
| INT t1e1Function | 1.3.6.1.4.1.321.100.2.3.1.1.21 | INTEGER | read-write | Specifies the function the network port will perform in the unit. The options are: t1e1FunctionNetwork (Independent network port) t1e1FunctionSlaved (Slaved to another network port) t1e1FunctionBackup (Automatic Protection Switching Backup for another network port) |
| INT t1e1EBitGeneration | 1.3.6.1.4.1.321.100.2.3.1.1.22 | INTEGER | read-write | |
| INT t1e1RAIGeneration | 1.3.6.1.4.1.321.100.2.3.1.1.23 | INTEGER | read-write | |
| INT t1e1SpareBitInsertion | 1.3.6.1.4.1.321.100.2.3.1.1.24 | INTEGER | read-write | |
| OCT t1e1Sa4In | 1.3.6.1.4.1.321.100.2.3.1.1.25 | OCTET STRING | read-only | |
| OCT t1e1Sa5In | 1.3.6.1.4.1.321.100.2.3.1.1.26 | OCTET STRING | read-only | |
| OCT t1e1Sa6In | 1.3.6.1.4.1.321.100.2.3.1.1.27 | OCTET STRING | read-only | |
| OCT t1e1Sa7In | 1.3.6.1.4.1.321.100.2.3.1.1.28 | OCTET STRING | read-only | |
| OCT t1e1Sa8In | 1.3.6.1.4.1.321.100.2.3.1.1.29 | OCTET STRING | read-only | |
| OCT t1e1Sa4Out | 1.3.6.1.4.1.321.100.2.3.1.1.30 | OCTET STRING | read-write | |
| OCT t1e1Sa5Out | 1.3.6.1.4.1.321.100.2.3.1.1.31 | OCTET STRING | read-write | |
| OCT t1e1Sa6Out | 1.3.6.1.4.1.321.100.2.3.1.1.32 | OCTET STRING | read-write | |
| OCT t1e1Sa7Out | 1.3.6.1.4.1.321.100.2.3.1.1.33 | OCTET STRING | read-write | |
| OCT t1e1Sa8Out | 1.3.6.1.4.1.321.100.2.3.1.1.34 | OCTET STRING | read-write | |
| t1e1AlarmTable | 1.3.6.1.4.1.321.100.2.3.2 | not-accessible | The T1 and E1 Alarm Table. | |
| t1e1AlarmTableEntry | 1.3.6.1.4.1.321.100.2.3.2.1 | not-accessible | An entry in the t1e1Table. | |
| INT t1e1AlarmNearIndex | 1.3.6.1.4.1.321.100.2.3.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT t1e1AlarmFarIndex | 1.3.6.1.4.1.321.100.2.3.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT t1e1AlarmIndex | 1.3.6.1.4.1.321.100.2.3.2.1.3 | INTEGER | read-only | This object is the index into the t1e1Table. |
| STR t1e1StatusSummary | 1.3.6.1.4.1.321.100.2.3.2.1.4 | DisplayString | read-only | This object provides a summary of the port status. |
| STR t1e1AlarmSummary | 1.3.6.1.4.1.321.100.2.3.2.1.5 | DisplayString | read-only | This object provides a summary of the port alarms. |
| INT t1e1ESStatus | 1.3.6.1.4.1.321.100.2.3.2.1.6 | INTEGER | read-only | Reports if an Errored Second condition exists. |
| INT t1e1ESCount | 1.3.6.1.4.1.321.100.2.3.2.1.7 | INTEGER | read-only | This count contains the number of consecutive seconds an Errored Second condition has existed. |
| INT t1e1ESThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.8 | INTEGER | read-write | Sets the Errored Seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1ESAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.9 | INTEGER | read-only | This status indicates if the Errors Seconds threshold is exceeded. |
| INT t1e1SESStatus | 1.3.6.1.4.1.321.100.2.3.2.1.10 | INTEGER | read-only | Reports if a Severely Errored condition exists. |
| INT t1e1SESCount | 1.3.6.1.4.1.321.100.2.3.2.1.11 | INTEGER | read-only | This count contains the number of consecutive seconds a Severely Errored condition has existed. |
| INT t1e1SESThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.12 | INTEGER | read-write | Sets the Severely Errored seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1SESAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.13 | INTEGER | read-only | This status indicates if the Severely Errors Seconds threshold is exceeded. |
| INT t1e1LOSSStatus | 1.3.6.1.4.1.321.100.2.3.2.1.14 | INTEGER | read-only | Reports if a Loss of Signal condition exists. |
| INT t1e1LOSSCount | 1.3.6.1.4.1.321.100.2.3.2.1.15 | INTEGER | read-only | This count contains the number of consecutive seconds a Loss of Signal condition has existed. |
| INT t1e1LOSSThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.16 | INTEGER | read-write | Sets the Loss of Signal seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1LOSSAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.17 | INTEGER | read-only | This status indicates if the Loss of Signal Seconds threshold is exceeded. |
| INT t1e1UASStatus | 1.3.6.1.4.1.321.100.2.3.2.1.18 | INTEGER | read-only | Reports if an Unavailable condition exists. |
| INT t1e1UASCount | 1.3.6.1.4.1.321.100.2.3.2.1.19 | INTEGER | read-only | This count contains the number of consecutive seconds an Unavailable condition has existed. |
| INT t1e1UASThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.20 | INTEGER | read-write | Sets the unavailable seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1UASAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.21 | INTEGER | read-only | This status indicates if the Unavailable Seconds threshold is exceeded. |
| INT t1e1CSSStatus | 1.3.6.1.4.1.321.100.2.3.2.1.22 | INTEGER | read-only | Reports if a Controlled Slip condition exists. |
| INT t1e1CSSCount | 1.3.6.1.4.1.321.100.2.3.2.1.23 | INTEGER | read-only | This count contains the number of consecutive seconds in which at least one Controlled Slip occurred. |
| INT t1e1CSSThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.24 | INTEGER | read-write | Sets the Controlled Slip seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1CSSAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.25 | INTEGER | read-only | This status indicates if the Controlled Slip seconds threshold is exceeded. |
| INT t1e1BPVSStatus | 1.3.6.1.4.1.321.100.2.3.2.1.26 | INTEGER | read-only | Reports if a Bipolar Violation Error condition exists. |
| INT t1e1BPVSCount | 1.3.6.1.4.1.321.100.2.3.2.1.27 | INTEGER | read-only | This count contains the number of consecutive seconds a Bipolar Violation Error condition has existed. |
| INT t1e1BPVSThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.28 | INTEGER | read-write | Sets the Bipolar Violation Error seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1BPVSAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.29 | INTEGER | read-only | This status indicates if the Bipolar Violation Error seconds threshold is exceeded. |
| INT t1e1OOFSStatus | 1.3.6.1.4.1.321.100.2.3.2.1.30 | INTEGER | read-only | Indicates that the unit is unable to synchronize on the incoming framing pattern. |
| INT t1e1OOFSCount | 1.3.6.1.4.1.321.100.2.3.2.1.31 | INTEGER | read-only | This count contains the number of consecutive seconds an OOF condition has existed. |
| INT t1e1OOFSThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.32 | INTEGER | read-write | Sets the OOF seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1OOFSAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.33 | INTEGER | read-only | Indicates if an OOF seconds alarm condition exists. |
| INT t1e1AISStatus | 1.3.6.1.4.1.321.100.2.3.2.1.34 | INTEGER | read-only | Indicates that the unit is receiving an unframed all ones pattern. |
| INT t1e1AISCount | 1.3.6.1.4.1.321.100.2.3.2.1.35 | INTEGER | read-only | This count contains the number of consecutive seconds an Unframed All Ones condition has existed. |
| INT t1e1AISThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.36 | INTEGER | read-write | Sets the AIS seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1AISAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.37 | INTEGER | read-only | Indicates if an Unframed All Ones alarm condition exists. |
| INT t1e1RASStatus | 1.3.6.1.4.1.321.100.2.3.2.1.38 | INTEGER | read-only | Reports if a Remote (Yellow) Alarm condition exists. |
| INT t1e1RASCount | 1.3.6.1.4.1.321.100.2.3.2.1.39 | INTEGER | read-only | This count contains the number of consecutive seconds a Remote (Yellow) Alarm condition has existed. |
| INT t1e1RASThreshold | 1.3.6.1.4.1.321.100.2.3.2.1.40 | INTEGER | read-write | Sets the RAS seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900. |
| INT t1e1RASAlarm | 1.3.6.1.4.1.321.100.2.3.2.1.41 | INTEGER | read-only | This status indicates if a Remote (Yellow) Alarm exists. |
| INT t1e1AlarmResetTimer | 1.3.6.1.4.1.321.100.2.3.2.1.42 | INTEGER | read-write | Sets the Alarm Reset Timer, this field can be set to any value in the range 0 to 900. |
| INT t1e1AlarmReset | 1.3.6.1.4.1.321.100.2.3.2.1.43 | INTEGER | read-write | This is used to clear the current alarm counts. |
| ddsNet | 1.3.6.1.4.1.321.100.2.4 | |||
| ddsNetConfigTable | 1.3.6.1.4.1.321.100.2.4.1 | not-accessible | The dds Network Interface Configuration Table. | |
| ddsNetConfigTableEntry | 1.3.6.1.4.1.321.100.2.4.1.1 | not-accessible | An entry in the Network Interface Table. | |
| INT ddsNetConfigNearIndex | 1.3.6.1.4.1.321.100.2.4.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT ddsNetConfigFarIndex | 1.3.6.1.4.1.321.100.2.4.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT ddsNetConfigIndex | 1.3.6.1.4.1.321.100.2.4.1.1.3 | INTEGER | read-only | Index into the ddsNetConfigTable. |
| STR ddsNetDescription | 1.3.6.1.4.1.321.100.2.4.1.1.4 | DisplayString | read-write | Contains a textual description of the port. |
| INT ddsNetRate | 1.3.6.1.4.1.321.100.2.4.1.1.5 | INTEGER | read-write | This object is the identifier of the current DDS network rate. The values mean: ddsNetRate2400 the DDS network interface is operating at 2400bps ddsNetRate4800 the DDS network interface is operating at 4800bps ddsNetRate9600 the DDS network interface is operating at 9600bps ddsNetRate19200 the DDS network interface is operating at 19200bps ddsNetRate38400 the DDS network interface is operating at 38400bps ddsNetRate56000 the DDS network interface is operating at 56000bps ddsNetRate64000 the DDS network interface is operating at 64000bps |
| INT ddsNetMode | 1.3.6.1.4.1.321.100.2.4.1.1.6 | INTEGER | read-write | This variable describes mode in which data is being sent from the DDS unit back towards the network. Changing the value of this variable can cause a loss of remote communications. The values mean: ddsNetModeNormal (DDS-I) normal data mode of operation ddsNetModeProprietaryTXPI (DDS-I) data being sent out on the DDS network is in a proprietary mode to allow for remote communications, rate adaption, and SYNC to ASYNC modes ddsNetMode64KClearChannel (DDS-II) A special case of DDS-II, where the line rate is 72K, the data rate is 64K, and there is no secondary channel. ddsNetMode64KCCProprietaryTXPII (DDS-II) A special case of DDS-II, where the line rate is 72K, the data rate is 64K, and there is no secondary channel. In addition, the data being sent out on the DDS network is in a proprietary mode to allow for remote communications, rate adaption, SYNC to ASYNC, and/or TDM modes. |
| INT ddsNetTimingSource | 1.3.6.1.4.1.321.100.2.4.1.1.7 | INTEGER | read-write | This variable describes the current timing source for the DDS network interface. The values mean: ddsNetTimingNet unit dependant upon network for DDS network interface timing ddsNetTimingInt unit supplying timing for DDS network interface ddsNetTimingDTE unit dependant upon DTE device for network interface timing ddsNetTimingPort1 unit dependant upon serial port 1 device for network interface timing ddsNetTimingPort2 unit dependant upon serial port 2 device for network interface timing |
| INT ddsNetRemComm | 1.3.6.1.4.1.321.100.2.4.1.1.8 | INTEGER | read-only | This variable describes the current setting for the remote communications link. The values mean: ddsNetRemCommEnabled remote communications can be carried out end to end ddsNetRemCommDisabled remote communications are not allowed ddsNetRemCommNotAvailable this unit does not support remote communications |
| INT ddsNetCircuitAssur | 1.3.6.1.4.1.321.100.2.4.1.1.9 | INTEGER | read-write | This variable describes the current setting for the circuit assurance option. The values mean: ddsNetCircuitAssurEnabled Circuit Assurance is enabled and the integrity of the DDS loop will be maintained ddsNetCircuitAssurDisabled Circuit Assurance is disabled ddsNetCircuitAssurNotAvailable this unit does not support Circuit Assurance |
| INT ddsNetAntiStrTimer | 1.3.6.1.4.1.321.100.2.4.1.1.10 | INTEGER | read-write | This variable describes the current setting for the anti streaming timer. The values mean: ddsNetAntiStrTimerOff the AntiStreaming Timer is off ddsNetAntiStrTimer10 the AntiStreaming Timer is set to 10 seconds ddsNetAntiStrTimer30 the AntiStreaming Timer is set to 30 seconds ddsNetAntiStrTimer60 the AntiStreaming Timer is set to 60 seconds |
| ddsNetAlarmTable | 1.3.6.1.4.1.321.100.2.4.2 | not-accessible | The dds Network Interface Alarm Table. | |
| ddsNetAlarmTableEntry | 1.3.6.1.4.1.321.100.2.4.2.1 | not-accessible | An entry in the ddsNetAlarmTable. | |
| INT ddsNetAlarmNearIndex | 1.3.6.1.4.1.321.100.2.4.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT ddsNetAlarmFarIndex | 1.3.6.1.4.1.321.100.2.4.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT ddsNetAlarmIndex | 1.3.6.1.4.1.321.100.2.4.2.1.3 | INTEGER | read-only | Index into the ddsNetAlarmTable. |
| STR ddsNetStatusSummary | 1.3.6.1.4.1.321.100.2.4.2.1.4 | DisplayString | read-only | This object provides a summary of the port status. |
| STR ddsNetAlarmSummary | 1.3.6.1.4.1.321.100.2.4.2.1.5 | DisplayString | read-only | This object provides a summary of the port alarms. |
| INT ddsNetLOSStatus | 1.3.6.1.4.1.321.100.2.4.2.1.6 | INTEGER | read-only | Reports if a Loss of Signal condition exists. |
| INT ddsNetLOSCount | 1.3.6.1.4.1.321.100.2.4.2.1.7 | INTEGER | read-only | This count contains the number of consecutive seconds the unit received signal has been interrupted. |
| INT ddsNetLOSThreshold | 1.3.6.1.4.1.321.100.2.4.2.1.8 | INTEGER | read-write | A period, measured in seconds, in which the DDS received signal is interrupted. |
| INT ddsNetLOSAlarm | 1.3.6.1.4.1.321.100.2.4.2.1.9 | INTEGER | read-only | This status indicates if the Loss of Signal Seconds threshold is exceeded. |
| INT ddsNetOOFStatus | 1.3.6.1.4.1.321.100.2.4.2.1.10 | INTEGER | read-only | Reports if an Out of Frame condition exists. |
| INT ddsNetOOFCount | 1.3.6.1.4.1.321.100.2.4.2.1.11 | INTEGER | read-only | This count contains the number of consecutive seconds the unit has received the out of frame code. |
| INT ddsNetOOFThreshold | 1.3.6.1.4.1.321.100.2.4.2.1.12 | INTEGER | read-write | A period, measured in seconds, in which the Out Of Frame code is received or a frame sync loss occurred. |
| INT ddsNetOOFAlarm | 1.3.6.1.4.1.321.100.2.4.2.1.13 | INTEGER | read-only | This status indicates if the Out of Frame Seconds threshold is exceeded. |
| INT ddsNetOOSStatus | 1.3.6.1.4.1.321.100.2.4.2.1.14 | INTEGER | read-only | Reports if Out of Service codes are received. |
| INT ddsNetOOSCount | 1.3.6.1.4.1.321.100.2.4.2.1.15 | INTEGER | read-only | This count contains the number of consecutive seconds the unit has received the out of service code. |
| INT ddsNetOOSThreshold | 1.3.6.1.4.1.321.100.2.4.2.1.16 | INTEGER | read-write | A period, measured in seconds, in which the Out Of Service code is received. |
| INT ddsNetOOSAlarm | 1.3.6.1.4.1.321.100.2.4.2.1.17 | INTEGER | read-only | This status indicates if the Out of Service Seconds threshold is exceeded. |
| INT ddsNetFDLStatus | 1.3.6.1.4.1.321.100.2.4.2.1.18 | INTEGER | read-only | Reports if Facility Data Link errors have occurred. |
| INT ddsNetFDLCount | 1.3.6.1.4.1.321.100.2.4.2.1.19 | INTEGER | read-only | This count contains the number of consecutive seconds in which FDL errors have occurred. |
| INT ddsNetFDLThreshold | 1.3.6.1.4.1.321.100.2.4.2.1.20 | INTEGER | read-write | A period, measured in seconds, in which FDL errors have occurred. |
| INT ddsNetFDLAlarm | 1.3.6.1.4.1.321.100.2.4.2.1.21 | INTEGER | read-only | This status indicates if the Facility Data Link threshold is exceeded. |
| INT ddsNetAlarmResetTimer | 1.3.6.1.4.1.321.100.2.4.2.1.22 | INTEGER | read-write | Sets the Alarm Reset Timer, this field can be set to any value in the range 0 to 900. |
| INT ddsNetAlarmReset | 1.3.6.1.4.1.321.100.2.4.2.1.23 | INTEGER | read-write | This is used to clear the current alarm counts. |
| INT ddsNetBPVStatus | 1.3.6.1.4.1.321.100.2.4.2.1.24 | INTEGER | read-only | Reports if a Bipolar violation event occurred in the last second. |
| INT ddsNetBPVCount | 1.3.6.1.4.1.321.100.2.4.2.1.25 | INTEGER | read-only | This count contains the number of consecutive seconds the unit received bipolar violations. |
| INT ddsNetBPVThreshold | 1.3.6.1.4.1.321.100.2.4.2.1.26 | INTEGER | read-write | A period, measured in seconds, in which the unit receives bipolar violations before an alarm is triggered. |
| INT ddsNetBPVAlarm | 1.3.6.1.4.1.321.100.2.4.2.1.27 | INTEGER | read-only | This status indicates if the Bipolar violation Seconds threshold is exceeded. |
| serialDte | 1.3.6.1.4.1.321.100.2.5 | |||
| serialDteConfigTable | 1.3.6.1.4.1.321.100.2.5.1 | not-accessible | The Serial DTE Config Table. | |
| serialDteConfigTableEntry | 1.3.6.1.4.1.321.100.2.5.1.1 | not-accessible | An entry in the serial DTE Config Table. | |
| INT serialDteConfigNearIndex | 1.3.6.1.4.1.321.100.2.5.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT serialDteConfigFarIndex | 1.3.6.1.4.1.321.100.2.5.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT serialDteConfigIndex | 1.3.6.1.4.1.321.100.2.5.1.1.3 | INTEGER | read-only | Index into the DteTable. |
| STR serialDteDescription | 1.3.6.1.4.1.321.100.2.5.1.1.4 | DisplayString | read-only | Contains a textual description of the port. |
| INT serialDteType | 1.3.6.1.4.1.321.100.2.5.1.1.5 | INTEGER | read-write | Selects the DTE port type if applicable. |
| INT serialDteRate | 1.3.6.1.4.1.321.100.2.5.1.1.6 | INTEGER | read-write | Selects the DTE port bit. |
| INT serialDteInvertData | 1.3.6.1.4.1.321.100.2.5.1.1.7 | INTEGER | read-write | Specifies whether transmit and receive are inverted at the port. |
| INT serialDteFormat | 1.3.6.1.4.1.321.100.2.5.1.1.8 | INTEGER | read-write | This variable describes the current operations format of the DTE interface. The values mean: serialDteFormatSync The DTE interface is currently set to operate in Synchronous clocking format serialDteFormatAsync The DTE interface is currently set to operate in the Asynchronous clocking format serialDteFormatNotAvail The DTE interface operating format is not available |
| INT serialDteParity | 1.3.6.1.4.1.321.100.2.5.1.1.9 | INTEGER | read-write | This variable describes the current parity selected for the DTE interface. This variable is only valid when the DTE Mode is set to ASYNC. The values mean: serialDteParityNone The DTE interface is currently set for no parity bit checking or generation serialDteParityOdd The DTE interface is currently set for odd parity serialDteParityEven The DTE interface is currently set for even parity serialDteParityMark The DTE interface is currently set for mark parity serialDteParitySpace The DTE interface is currently set for space parity serialDteParityNotAvail The parity setting on the DTE interface is not available. |
| INT serialDteStopBit | 1.3.6.1.4.1.321.100.2.5.1.1.10 | INTEGER | read-write | This variable describes the stop bit setting for the DTE interface. This variable is only valid when the DTE interface is set to ASYNC. The values mean: serialDteStopBit1 The DTE interface is configured to operate in the ASYNC mode with 1 stop bit serialDteStopBit2 The DTE interface is configured to operate in the ASYNC mode with 2 stop bits serialDteStopBitNotAvail The stop bit information is not available. The DTE interface is probably configured for synchronous operation. |
| INT serialDteMode | 1.3.6.1.4.1.321.100.2.5.1.1.11 | INTEGER | read-write | This variable describes mode in which data is being sent from the DDS unit back towards the network. |
| INT serialDteDSR | 1.3.6.1.4.1.321.100.2.5.1.1.12 | INTEGER | read-write | Selects DSR behavior. |
| INT serialDteDCD | 1.3.6.1.4.1.321.100.2.5.1.1.13 | INTEGER | read-write | Selects DCD behavior. |
| INT serialDteRTS | 1.3.6.1.4.1.321.100.2.5.1.1.14 | INTEGER | read-write | Selects RTS behavior. |
| INT serialDteRTSDelay | 1.3.6.1.4.1.321.100.2.5.1.1.15 | INTEGER | read-write | Selects RTS to CTS transition delay. |
| INT serialDteDTR | 1.3.6.1.4.1.321.100.2.5.1.1.16 | INTEGER | read-only | Reports if DTR from the DTE device is false. |
| INT serialDteCTS | 1.3.6.1.4.1.321.100.2.5.1.1.17 | INTEGER | read-write | Specifies the control of the CTS signal at the port. |
| INT serialDteV54 | 1.3.6.1.4.1.321.100.2.5.1.1.18 | INTEGER | read-write | Specifies if the unit should respond to inband V.54 loop commands. |
| INT serialDteLL | 1.3.6.1.4.1.321.100.2.5.1.1.19 | INTEGER | read-write | Specifies if the unit should respond to local loop activation by the local loopback signal (EIA530 or RS-232 pin 18). |
| INT serialDteRL | 1.3.6.1.4.1.321.100.2.5.1.1.20 | INTEGER | read-write | Specifies if the unit should respond to remote loop activation by the remote loopback signal (EIA530 or RS-232 pin 21). |
| INT serialDteStartChannel | 1.3.6.1.4.1.321.100.2.5.1.1.21 | INTEGER | read-write | Specifies the starting channel for the interface. |
| INT serialDteNumberOfChannels | 1.3.6.1.4.1.321.100.2.5.1.1.22 | INTEGER | read-write | Specifies the number of channels allocated to the interface. |
| INT serialDteTxClock | 1.3.6.1.4.1.321.100.2.5.1.1.23 | INTEGER | read-write | Specifies how the interface derives its transmit clock. |
| INT serialDteBundle | 1.3.6.1.4.1.321.100.2.5.1.1.24 | INTEGER | read-write | Specifies the allocation pattern of channels assigned to the serial port. |
| INT serialDteChannelRate | 1.3.6.1.4.1.321.100.2.5.1.1.25 | INTEGER | read-write | Specifies the rate of all channels assigned to the serial port. |
| INT serialDteInvertClock | 1.3.6.1.4.1.321.100.2.5.1.1.26 | INTEGER | read-write | Specifies if an inverted clock is used to send data from the serial port. |
| INT serialDteCharSize | 1.3.6.1.4.1.321.100.2.5.1.1.27 | INTEGER | read-write | Specifies the number of bits per character. This variable is valid in ASYNC mode. |
| INT serialDteFlowControl | 1.3.6.1.4.1.321.100.2.5.1.1.28 | INTEGER | read-write | Specifies the Flow control to use. This variable is valid only in ASYNC mode. |
| STR serialDtePinStatus | 1.3.6.1.4.1.321.100.2.5.1.1.29 | DisplayString | read-only | This object provides a summary of the Serial port pin status. |
| INT serialDteInInvertClock | 1.3.6.1.4.1.321.100.2.5.1.1.30 | INTEGER | read-write | Specifies to use the inverted clock edge for data clocked into the serial port. |
| serialDteAlarmTable | 1.3.6.1.4.1.321.100.2.5.2 | not-accessible | The Serial DTE Alarm Table. | |
| serialDteAlarmTableEntry | 1.3.6.1.4.1.321.100.2.5.2.1 | not-accessible | An entry in the serial DTE Alarm Table. | |
| INT serialDteAlarmNearIndex | 1.3.6.1.4.1.321.100.2.5.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT serialDteAlarmFarIndex | 1.3.6.1.4.1.321.100.2.5.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT serialDteAlarmIndex | 1.3.6.1.4.1.321.100.2.5.2.1.3 | INTEGER | read-only | Index into the serialDteAlarmTable. |
| INT serialDteDTRAlarmControl | 1.3.6.1.4.1.321.100.2.5.2.1.4 | INTEGER | read-write | Specifies if the unit should alarm on loss of DTR. |
| INT serialDteDTRAlarmStatus | 1.3.6.1.4.1.321.100.2.5.2.1.5 | INTEGER | read-only | This status indicates a DTR Loss alarm is active. |
| STR serialDteStatusSummary | 1.3.6.1.4.1.321.100.2.5.2.1.6 | DisplayString | read-only | This object provides a summary of the port status. |
| STR serialDteAlarmSummary | 1.3.6.1.4.1.321.100.2.5.2.1.7 | DisplayString | read-only | This object provides a summary of the port alarms. |
| INT serialDteASCStatus | 1.3.6.1.4.1.321.100.2.5.2.1.8 | INTEGER | read-only | Reports if an ASC condition exists on the interface. |
| INT serialDteASCCount | 1.3.6.1.4.1.321.100.2.5.2.1.9 | INTEGER | read-only | This count contains the number of ASC seconds received by the interface. |
| INT serialDteASCThreshold | 1.3.6.1.4.1.321.100.2.5.2.1.10 | INTEGER | read-write | The number of ASC seconds that must be received before an alarm is declared. |
| INT serialDteASCAlarm | 1.3.6.1.4.1.321.100.2.5.2.1.11 | INTEGER | read-only | This status indicates if the ASC Seconds threshold is exceeded. |
| INT serialDteFDLStatus | 1.3.6.1.4.1.321.100.2.5.2.1.12 | INTEGER | read-only | Reports if an FDL error condition exists on the interface. |
| INT serialDteFDLCount | 1.3.6.1.4.1.321.100.2.5.2.1.13 | INTEGER | read-only | This count contains the number of FDL errored seconds received by the interface. |
| INT serialDteFDLThreshold | 1.3.6.1.4.1.321.100.2.5.2.1.14 | INTEGER | read-write | The number of FDL errored seconds that must be received before an alarm is declared. |
| INT serialDteFDLAlarm | 1.3.6.1.4.1.321.100.2.5.2.1.15 | INTEGER | read-only | This status indicates if the FDL Errored Seconds threshold is exceeded. |
| INT serialDteLOSStatus | 1.3.6.1.4.1.321.100.2.5.2.1.16 | INTEGER | read-only | Reports if an LOS condition exists on the interface. |
| INT serialDteLOSCount | 1.3.6.1.4.1.321.100.2.5.2.1.17 | INTEGER | read-only | This count contains the number of LOS seconds received by the interface. |
| INT serialDteLOSThreshold | 1.3.6.1.4.1.321.100.2.5.2.1.18 | INTEGER | read-write | The number of LOS seconds that must be received before an alarm is declared. |
| INT serialDteLOSAlarm | 1.3.6.1.4.1.321.100.2.5.2.1.19 | INTEGER | read-only | This status indicates if the LOS Seconds threshold is exceeded. |
| analogDte | 1.3.6.1.4.1.321.100.2.6 | |||
| analogDteTable | 1.3.6.1.4.1.321.100.2.6.1 | not-accessible | The Analog DTE Table. | |
| analogDteTableEntry | 1.3.6.1.4.1.321.100.2.6.1.1 | not-accessible | An entry in the Analog DTE Table. | |
| INT analogDteNearIndex | 1.3.6.1.4.1.321.100.2.6.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT analogDteFarIndex | 1.3.6.1.4.1.321.100.2.6.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT analogDteIndex | 1.3.6.1.4.1.321.100.2.6.1.1.3 | INTEGER | read-only | Index into the analogDteTable. |
| STR analogDteDescription | 1.3.6.1.4.1.321.100.2.6.1.1.4 | DisplayString | read-only | Contains a textual description of the port. |
| INT analogDteCardType | 1.3.6.1.4.1.321.100.2.6.1.1.5 | INTEGER | read-only | Identifies the analog DTE card type. |
| INT analogDteMode | 1.3.6.1.4.1.321.100.2.6.1.1.6 | INTEGER | read-write | Selects whether the port is actively assigned to a network channel or not used. |
| INT analogDteState | 1.3.6.1.4.1.321.100.2.6.1.1.7 | INTEGER | read-only | Displays the port status as either in the Busy or Idle state. |
| STR analogDteElementID | 1.3.6.1.4.1.321.100.2.6.1.1.8 | DisplayString | read-write | This object signifies the name of the device. |
| INT analogDteSignalling | 1.3.6.1.4.1.321.100.2.6.1.1.9 | INTEGER | read-write | Selects the supervisory operation of the port. |
| INT analogDteDNISDelay | 1.3.6.1.4.1.321.100.2.6.1.1.10 | INTEGER | read-write | If the signalling mode has a delay, it can be set from 1 to 5 seconds. |
| INT analogDteTxGain | 1.3.6.1.4.1.321.100.2.6.1.1.11 | INTEGER | read-write | Selects the transmit gain. Values prefixed with m are negative. |
| INT analogDteRxGain | 1.3.6.1.4.1.321.100.2.6.1.1.12 | INTEGER | read-write | Selects the receive gain. Values prefixed with m are negative. |
| connection | 1.3.6.1.4.1.321.100.2.7 | |||
| connectionTable | 1.3.6.1.4.1.321.100.2.7.1 | not-accessible | The connection table. | |
| connectionTableEntry | 1.3.6.1.4.1.321.100.2.7.1.1 | not-accessible | An entry in the connection table. | |
| INT connectionNearIndex | 1.3.6.1.4.1.321.100.2.7.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT connectionFarIndex | 1.3.6.1.4.1.321.100.2.7.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT connectionTableIndex | 1.3.6.1.4.1.321.100.2.7.1.1.3 | INTEGER | read-only | The index into the connection table. |
| STR connectionTableDescription | 1.3.6.1.4.1.321.100.2.7.1.1.4 | DisplayString | read-only | A description of the connection. |
| connectionChannelTable | 1.3.6.1.4.1.321.100.2.7.2 | not-accessible | The channel-level connection table. | |
| connectionChannelEntry | 1.3.6.1.4.1.321.100.2.7.2.1 | not-accessible | An entry in the connectionChannelTable. | |
| INT connectionChannelNearIndex | 1.3.6.1.4.1.321.100.2.7.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT connectionChannelFarIndex | 1.3.6.1.4.1.321.100.2.7.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT connectionChannelLineIndex | 1.3.6.1.4.1.321.100.2.7.2.1.3 | INTEGER | read-only | Selects instance of line. |
| INT connectionChannelIndex | 1.3.6.1.4.1.321.100.2.7.2.1.4 | INTEGER | read-only | The index into the connection table. |
| INT channelInterfaceAssignment | 1.3.6.1.4.1.321.100.2.7.2.1.5 | INTEGER | read-write | The channel assignment. |
| STR channelInterfaceDescription | 1.3.6.1.4.1.321.100.2.7.2.1.6 | DisplayString | read-only | Contains a description of the interface channel connection. |
| INT channelInterfaceChannel | 1.3.6.1.4.1.321.100.2.7.2.1.7 | INTEGER | read-write | Displays the corresponding channel of the interface channel connection. |
| INT channelSignalling | 1.3.6.1.4.1.321.100.2.7.2.1.8 | INTEGER | read-write | Allows a selection of Clear Channel or Robbed Bit signalling for each DS0. |
| maintenance | 1.3.6.1.4.1.321.100.2.8 | |||
| bertTable | 1.3.6.1.4.1.321.100.2.8.1 | not-accessible | BERT control table. | |
| bertTableEntry | 1.3.6.1.4.1.321.100.2.8.1.1 | not-accessible | An entry in the BERT control table. | |
| INT bertNearIndex | 1.3.6.1.4.1.321.100.2.8.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT bertFarIndex | 1.3.6.1.4.1.321.100.2.8.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT bertIndex | 1.3.6.1.4.1.321.100.2.8.1.1.3 | INTEGER | read-only | The index into the BERT control table. Selects which BERT chip to use. |
| INT bertPattern | 1.3.6.1.4.1.321.100.2.8.1.1.4 | INTEGER | read-write | Selects the test pattern to be used. |
| INT bertLength | 1.3.6.1.4.1.321.100.2.8.1.1.5 | INTEGER | read-write | Specifies how long the test should run. |
| INT bertPatternSync | 1.3.6.1.4.1.321.100.2.8.1.1.6 | INTEGER | read-only | Displays the current state of pattern sync during a test. |
| INT bertElapsedTime | 1.3.6.1.4.1.321.100.2.8.1.1.7 | INTEGER | read-only | Displays the amount of time elapsed since a timed test began in seconds. |
| INT bertBitErrors | 1.3.6.1.4.1.321.100.2.8.1.1.8 | INTEGER | read-only | Displays the total number of bit errors detected since the test began. |
| INT bertErroredSeconds | 1.3.6.1.4.1.321.100.2.8.1.1.9 | INTEGER | read-only | Displays the number of asynchronous errored seconds that have been detected since the test began. |
| INT bertPercentEFS | 1.3.6.1.4.1.321.100.2.8.1.1.10 | INTEGER | read-only | Displays a ratio derived from the number of error free seconds divided by the number of seconds accumulated in elapsed time. |
| INT bertCommand | 1.3.6.1.4.1.321.100.2.8.1.1.11 | INTEGER | read-write | Issues a test command for the interface. |
| bertInterfaceTable | 1.3.6.1.4.1.321.100.2.8.2 | not-accessible | BERT control interface table. | |
| bertInterfaceTableEntry | 1.3.6.1.4.1.321.100.2.8.2.1 | not-accessible | An entry in the BERT control interface table. | |
| INT bertInterfaceNearIndex | 1.3.6.1.4.1.321.100.2.8.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT bertInterfaceFarIndex | 1.3.6.1.4.1.321.100.2.8.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT bertChipIndex | 1.3.6.1.4.1.321.100.2.8.2.1.3 | INTEGER | read-only | Selects which BERT chip to use. |
| INT bertInterfaceIndex | 1.3.6.1.4.1.321.100.2.8.2.1.4 | INTEGER | read-only | An index into the MIB-II interfaces table; the interface for the BERT settings. |
| INT bertInterfaceSetting | 1.3.6.1.4.1.321.100.2.8.2.1.5 | INTEGER | read-write | Specifies where to send the BERT pattern. |
| INT bertInterfaceService | 1.3.6.1.4.1.321.100.2.8.2.1.6 | INTEGER | read-write | Specifies the service (see ipadv2.mib) to BERT. The bandwidth associated with the service will get the BERT pattern. |
| INT bertInterfaceChannelRate | 1.3.6.1.4.1.321.100.2.8.2.1.7 | INTEGER | read-write | Specifies the network channel rate for all channels involved in a network BERT. |
| testTable | 1.3.6.1.4.1.321.100.2.8.3 | not-accessible | Test control table. | |
| testTableEntry | 1.3.6.1.4.1.321.100.2.8.3.1 | not-accessible | An entry in the testTable. | |
| INT testNearIndex | 1.3.6.1.4.1.321.100.2.8.3.1.1 | INTEGER | read-only | Selects the near device. |
| INT testFarIndex | 1.3.6.1.4.1.321.100.2.8.3.1.2 | INTEGER | read-only | Selects the far device. |
| INT testTableIndex | 1.3.6.1.4.1.321.100.2.8.3.1.3 | INTEGER | read-only | The index into the testTable, one entry for each interface. |
| INT testType | 1.3.6.1.4.1.321.100.2.8.3.1.4 | INTEGER | read-write | Identifies the test type for the interface. |
| INT testLoopDirection | 1.3.6.1.4.1.321.100.2.8.3.1.5 | INTEGER | read-write | This object is the identifier of the current unit loop mode. The values mean: testLoopUnidirectional Line, Data, and V54 loops will be unidirectional Local loop will be bidirectional testLoopBidirectional All loops will be bidirectional |
| INT testFarLLBFraming | 1.3.6.1.4.1.321.100.2.8.3.1.6 | INTEGER | read-write | This setting, for Far LLB tests on T1 lines, must match the far end unit loop code framing. |
| INT testLoopInitiator | 1.3.6.1.4.1.321.100.2.8.3.1.7 | INTEGER | read-only | Indicates who started the loop. |
| INT testDefaultLoopType | 1.3.6.1.4.1.321.100.2.8.3.1.8 | INTEGER | read-write | Identifies the default loop type. |
| performance | 1.3.6.1.4.1.321.100.2.9 | |||
| performance24Table | 1.3.6.1.4.1.321.100.2.9.1 | not-accessible | Performance table, contains TR54016 standard and enhanced data. | |
| performance24TableEntry | 1.3.6.1.4.1.321.100.2.9.1.1 | not-accessible | An entry in the performance24Table. | |
| INT performance24NearIndex | 1.3.6.1.4.1.321.100.2.9.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT performance24FarIndex | 1.3.6.1.4.1.321.100.2.9.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT performance24InterfaceIndex | 1.3.6.1.4.1.321.100.2.9.1.1.3 | INTEGER | read-only | Selects the interface. |
| INT performance24Index | 1.3.6.1.4.1.321.100.2.9.1.1.4 | INTEGER | read-only | The index into the 24-hour performance table. |
| INT performance24ES | 1.3.6.1.4.1.321.100.2.9.1.1.5 | INTEGER | read-only | The number of Errored Seconds for the 15-minute period. |
| INT performance24BES | 1.3.6.1.4.1.321.100.2.9.1.1.6 | INTEGER | read-only | The number of Bursty Errored Seconds for the 15-minute period. |
| INT performance24SES | 1.3.6.1.4.1.321.100.2.9.1.1.7 | INTEGER | read-only | The number of Severely Errored Seconds for the 15-minute period. |
| INT performance24UAS | 1.3.6.1.4.1.321.100.2.9.1.1.8 | INTEGER | read-only | The number of Unavailable Seconds for the 15-minute period. |
| INT performance24LOFC | 1.3.6.1.4.1.321.100.2.9.1.1.9 | INTEGER | read-only | The number of Loss of Frame Counts for the 15-minute period. |
| INT performance24CSS | 1.3.6.1.4.1.321.100.2.9.1.1.10 | INTEGER | read-only | The number of Controlled Slip Seconds for the 15-minute period. |
| INT performance24CRCES | 1.3.6.1.4.1.321.100.2.9.1.1.11 | INTEGER | read-only | The number of CRC Errored Seconds for the 15-minute period. |
| INT performance24OOFS | 1.3.6.1.4.1.321.100.2.9.1.1.12 | INTEGER | read-only | The number of Out of Frame Seconds for the 15-minute period. |
| INT performance24LOSS | 1.3.6.1.4.1.321.100.2.9.1.1.13 | INTEGER | read-only | The number of Loss of Signal Seconds for the 15-minute period. |
| INT performance24AISS | 1.3.6.1.4.1.321.100.2.9.1.1.14 | INTEGER | read-only | The number of Alarm Indication Signal Seconds for the 15-minute period. |
| INT performance24RAS | 1.3.6.1.4.1.321.100.2.9.1.1.15 | INTEGER | read-only | The number of Remote Alarm (Yellow) Seconds for the 15-minute period. |
| INT performance24BPVS | 1.3.6.1.4.1.321.100.2.9.1.1.16 | INTEGER | read-only | The number of Bipolar Violation Seconds for the 15-minute period. |
| TIK performance24timestamp | 1.3.6.1.4.1.321.100.2.9.1.1.17 | TimeTicks | read-only | The value of sysUpTime when the statistics were last updated. |
| performance30Table | 1.3.6.1.4.1.321.100.2.9.2 | not-accessible | Performance table, contains TR54016 standard and enhanced 30-day data. | |
| performance30TableEntry | 1.3.6.1.4.1.321.100.2.9.2.1 | not-accessible | An entry in the performance30Table. | |
| INT performance30NearIndex | 1.3.6.1.4.1.321.100.2.9.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT performance30FarIndex | 1.3.6.1.4.1.321.100.2.9.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT performance30InterfaceIndex | 1.3.6.1.4.1.321.100.2.9.2.1.3 | INTEGER | read-only | Selects the interface. |
| INT performance30Index | 1.3.6.1.4.1.321.100.2.9.2.1.4 | INTEGER | read-only | The index into the 30-day performance table. |
| INT performance30ES | 1.3.6.1.4.1.321.100.2.9.2.1.5 | INTEGER | read-only | The number of Errored Seconds for the 1-day period. |
| INT performance30BES | 1.3.6.1.4.1.321.100.2.9.2.1.6 | INTEGER | read-only | The number of Bursty Errored Seconds for the 1-day period. |
| INT performance30SES | 1.3.6.1.4.1.321.100.2.9.2.1.7 | INTEGER | read-only | The number of Severely Errored Seconds for the 1-day period. |
| INT performance30UAS | 1.3.6.1.4.1.321.100.2.9.2.1.8 | INTEGER | read-only | The number of Unavailable Seconds for the 1-day period. |
| INT performance30LOFC | 1.3.6.1.4.1.321.100.2.9.2.1.9 | INTEGER | read-only | The number of Loss of Frame Counts for the 1-day period. |
| INT performance30CSS | 1.3.6.1.4.1.321.100.2.9.2.1.10 | INTEGER | read-only | The number of Controlled Slip Seconds for the 1-day period. |
| INT performance30CRCES | 1.3.6.1.4.1.321.100.2.9.2.1.11 | INTEGER | read-only | The number of CRC Errored Seconds for the 1-day period. |
| INT performance30OOFS | 1.3.6.1.4.1.321.100.2.9.2.1.12 | INTEGER | read-only | The number of Out of Frame Seconds for the 1-day period. |
| INT performance30LOSS | 1.3.6.1.4.1.321.100.2.9.2.1.13 | INTEGER | read-only | The number of Loss of Signal Seconds for the 1-day period. |
| INT performance30AISS | 1.3.6.1.4.1.321.100.2.9.2.1.14 | INTEGER | read-only | The number of Alarm Indication Signal Seconds for the 1-day period. |
| INT performance30RAS | 1.3.6.1.4.1.321.100.2.9.2.1.15 | INTEGER | read-only | The number of Remote Alarm (Yellow) Seconds for the 1-day period. |
| INT performance30BPVS | 1.3.6.1.4.1.321.100.2.9.2.1.16 | INTEGER | read-only | The number of Bipolar Violation Seconds for the 1-day period. |
| TIK performance30timestamp | 1.3.6.1.4.1.321.100.2.9.2.1.17 | TimeTicks | read-only | The value of sysUpTime when the statistics were last updated. |
| iTable | 1.3.6.1.4.1.321.100.2.10 | |||
| iTableEntry | 1.3.6.1.4.1.321.100.2.10.1.1 | not-accessible | An entry in the interface table. | |
| INT iTableNearIndex | 1.3.6.1.4.1.321.100.2.10.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT iTableFarIndex | 1.3.6.1.4.1.321.100.2.10.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT iTableIndex | 1.3.6.1.4.1.321.100.2.10.1.1.3 | INTEGER | read-only | The index into the interface table, used for addressing in above tables. |
| STR iDescription | 1.3.6.1.4.1.321.100.2.10.1.1.4 | DisplayString | read-only | Description of the interface. |
| INT iType | 1.3.6.1.4.1.321.100.2.10.1.1.5 | INTEGER | read-only | Enumerated interface type. |
| INT iSlot | 1.3.6.1.4.1.321.100.2.10.1.1.6 | INTEGER | read-only | Device-dependent slot in which the interface resides. |
| INT iPort | 1.3.6.1.4.1.321.100.2.10.1.1.7 | INTEGER | read-only | Device-dependent port in which the interface resides. |
| INT iStatus | 1.3.6.1.4.1.321.100.2.10.1.1.8 | INTEGER | read-only | Status of the interface. |
| traplog | 1.3.6.1.4.1.321.100.2.11 | |||
| traplogTable | 1.3.6.1.4.1.321.100.2.11.1 | not-accessible | The traplog table. | |
| traplogEntry | 1.3.6.1.4.1.321.100.2.11.1.1 | not-accessible | An entry in the traplog table. | |
| INT traplogIndex | 1.3.6.1.4.1.321.100.2.11.1.1.1 | INTEGER | read-only | The index into the traplog table. |
| INT traplogNearIndex | 1.3.6.1.4.1.321.100.2.11.1.1.2 | INTEGER | read-only | Specifies the near device. |
| INT traplogFarIndex | 1.3.6.1.4.1.321.100.2.11.1.1.3 | INTEGER | read-only | Specifies the far device. |
| INT traplogInterfaceIndex | 1.3.6.1.4.1.321.100.2.11.1.1.4 | INTEGER | read-only | Specifies the interface. |
| INT traplogTrapNum | 1.3.6.1.4.1.321.100.2.11.1.1.5 | INTEGER | read-only | The SNMP trap id. |
| STR traplogTimeStamp | 1.3.6.1.4.1.321.100.2.11.1.1.6 | DisplayString | read-only | Time the SNMP was generated. |
| INT traplogDeviceType | 1.3.6.1.4.1.321.100.2.11.1.1.7 | INTEGER | read-only | Specifies the device type for the trap. |
| STR traplogOID1 | 1.3.6.1.4.1.321.100.2.11.1.1.8 | DisplayString | read-only | SNMP Object ID of 1st varbind. |
| STR traplogDescription1 | 1.3.6.1.4.1.321.100.2.11.1.1.9 | DisplayString | read-only | Description of 1st varbind. |
| STR traplogValue1 | 1.3.6.1.4.1.321.100.2.11.1.1.10 | DisplayString | read-only | Value of of 1st varbind. |
| STR traplogOID2 | 1.3.6.1.4.1.321.100.2.11.1.1.11 | DisplayString | read-only | SNMP Object ID of 2nd varbind. |
| STR traplogDescription2 | 1.3.6.1.4.1.321.100.2.11.1.1.12 | DisplayString | read-only | Description of 2nd varbind. |
| STR traplogValue2 | 1.3.6.1.4.1.321.100.2.11.1.1.13 | DisplayString | read-only | Value of of 2nd varbind. |
| STR traplogOID3 | 1.3.6.1.4.1.321.100.2.11.1.1.14 | DisplayString | read-only | SNMP Object ID of 3rd varbind. |
| STR traplogDescription3 | 1.3.6.1.4.1.321.100.2.11.1.1.15 | DisplayString | read-only | Description of 3rd varbind. |
| STR traplogValue3 | 1.3.6.1.4.1.321.100.2.11.1.1.16 | DisplayString | read-only | Value of of 3rd varbind. |
| INT traplogDeleteEntry | 1.3.6.1.4.1.321.100.2.11.2 | INTEGER | read-write | Writing the index of a trap to this object will delete the trap entry. Writing an index value of 0 will delete all entries. |
| INT traplogSortOption | 1.3.6.1.4.1.321.100.2.11.3 | INTEGER | read-write | Determines the order in which traps are presented. |
| TIK traplogLastTimeStamp | 1.3.6.1.4.1.321.100.2.11.4 | TimeTicks | read-only | The timestamp of the newest trap in the trap log. |
| unitUtilities | 1.3.6.1.4.1.321.100.2.12 | |||
| unitUtilitiesTable | 1.3.6.1.4.1.321.100.2.12.1 | not-accessible | The unit utilities table. | |
| unitUtilitiesTableEntry | 1.3.6.1.4.1.321.100.2.12.1.1 | not-accessible | An entry in the unit utilities table. | |
| INT unitUtilitiesNearIndex | 1.3.6.1.4.1.321.100.2.12.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT unitUtilitiesFarIndex | 1.3.6.1.4.1.321.100.2.12.1.1.2 | INTEGER | read-only | Selects the far device. |
| STR unitUtilitiesLocalPassword | 1.3.6.1.4.1.321.100.2.12.1.1.3 | DisplayString | read-write | The password for local access to a device (VT100, front panel). |
| STR unitUtilitiesTime | 1.3.6.1.4.1.321.100.2.12.1.1.4 | DisplayString | read-write | This string is the current time as known to the device. The current time may be entered in this field using the HHMMSS format. For example, 3:45AM is entered as 034500 and 3:45PM is entered as 154500. |
| STR unitUtilitiesDate | 1.3.6.1.4.1.321.100.2.12.1.1.5 | DisplayString | read-write | This string is the current date as known to the device. The current date may be entered in this field using the MMDDYY format. For example, July 4, 1997 is entered as 070497. |
| INT unitUtilitiesMaintenanceReset | 1.3.6.1.4.1.321.100.2.12.1.1.6 | INTEGER | read-write | This field allows resetting the device to default values by reloading the start-up default configuration parameters. |
| INT unitUtilitiesAlarmResetTimer | 1.3.6.1.4.1.321.100.2.12.1.1.7 | INTEGER | read-write | This field allows setting a timer which will cause all existing alarms on the device to be cleared upon expiration. The counter is in seconds. |
| INT unitUtilitiesAlarmClear | 1.3.6.1.4.1.321.100.2.12.1.1.8 | INTEGER | read-write | Writing a value of utilitiesAlarmClearNow(2) to this field causes all existing alarms to be cleared immediately. |
| INT unitUtilitiesSaveConfig | 1.3.6.1.4.1.321.100.2.12.1.1.9 | INTEGER | read-write | This field commands the unit to save its configuration. |
| INT unitUtilitiesRestartStatus | 1.3.6.1.4.1.321.100.2.12.1.1.10 | INTEGER | read-only | This parameter indicates if the unit configuration needs to be saved and restarted. notNeeded - A save and restart is not needed at this time. recommended - A save and restart is recommended for optimal performance but not required. required - A save and restart is required for the unit to implement the altered configuration. |
| STR unitUtilitiesReadOnlyPassword | 1.3.6.1.4.1.321.100.2.12.1.1.11 | DisplayString | read-write | The password for read only access to a device (VT100, front panel). |
| INT unitUtilitiesPasswordLockoutEnable | 1.3.6.1.4.1.321.100.2.12.1.1.12 | INTEGER | read-write | This parameter is used to enable or disable the password lockout feature. |
| INT unitUtilitiesPasswordLockoutStatus | 1.3.6.1.4.1.321.100.2.12.1.1.13 | INTEGER | read-only | This parameter indicates if the password lockout feature is enabled or disabled, and if it is enabled this parameter may reflect if the password is indeed locked. |
| INT unitUtilitiesPasswordLockoutClear | 1.3.6.1.4.1.321.100.2.12.1.1.14 | INTEGER | read-write | This parameter is used to unlock a locked password. |
| productInfo | 1.3.6.1.4.1.321.100.2.13 | |||
| STR productModelNumber | 1.3.6.1.4.1.321.100.2.13.1 | DisplayString | read-only | This string displays the units model number |
| STR productModelDescr | 1.3.6.1.4.1.321.100.2.13.2 | DisplayString | read-only | This string displays a brief description of the unit |
| STR productElementId | 1.3.6.1.4.1.321.100.2.13.3 | DisplayString | read-write | This string is the same information that is in the element id field located in the utilities Screen of the unit's user interface. This field can be set from either location. |
| STR productSoftwareRev | 1.3.6.1.4.1.321.100.2.13.4 | DisplayString | read-only | This string reports the units current software revision |
| STR productHardwareRev | 1.3.6.1.4.1.321.100.2.13.5 | DisplayString | read-only | This string reports the units hardware revision |
| STR productSerialNum | 1.3.6.1.4.1.321.100.2.13.6 | DisplayString | read-only | This string displays the unit's serial number |
| STR productPhysicalAddress | 1.3.6.1.4.1.321.100.2.13.7 | DisplayString | read-only | This string displays the unit's physical ethernet address |
| STR productNmsAddress | 1.3.6.1.4.1.321.100.2.13.8 | DisplayString | read-only | This string displays the unit's NMS address which is used to identify it to the TxPORT management products |
| productLabelTable | 1.3.6.1.4.1.321.100.2.13.9 | not-accessible | The Product Label Table. | |
| productLabelTableEntry | 1.3.6.1.4.1.321.100.2.13.9.1 | not-accessible | An entry in the product label table. | |
| INT labelTableIndex | 1.3.6.1.4.1.321.100.2.13.9.1.1 | INTEGER | not-accessible | The index into the ProductLabelTable. |
| STR labelTableLabel | 1.3.6.1.4.1.321.100.2.13.9.1.2 | DisplayString | read-write | A product label. |
| STR labelTableValue | 1.3.6.1.4.1.321.100.2.13.9.1.3 | DisplayString | read-write | The data associated with the label. |
| netAPS | 1.3.6.1.4.1.321.100.2.14 | |||
| netAPSConfigTable | 1.3.6.1.4.1.321.100.2.14.1 | not-accessible | One to One network Automatic Protection Switching (APS) configuration parameters table. | |
| netAPSConfigTableEntry | 1.3.6.1.4.1.321.100.2.14.1.1 | not-accessible | An entry in the netAPSConfigTable. | |
| INT netAPSConfigNearIndex | 1.3.6.1.4.1.321.100.2.14.1.1.1 | INTEGER | read-only | Selects the near device. |
| INT netAPSConfigFarIndex | 1.3.6.1.4.1.321.100.2.14.1.1.2 | INTEGER | read-only | Selects the far device. |
| INT netAPSConfigifIndex | 1.3.6.1.4.1.321.100.2.14.1.1.3 | INTEGER | read-only | Selects the MIB-II ifIndex. |
| INT netAPSConfigOtherifIndex | 1.3.6.1.4.1.321.100.2.14.1.1.4 | INTEGER | read-write | MIB-II ifIndex of the other interface involved with the APS. |
| INT netAPSConfigMode | 1.3.6.1.4.1.321.100.2.14.1.1.5 | INTEGER | read-write | tr54017 - Implements TR54017 autoABswitch - Implements a single ended A/B switch between two independent lines masterAltCarrier - Master side of alternate carrier APS slaveAltCarrier - Slave side of alternate carrier APS |
| INT netAPSConfigRevert | 1.3.6.1.4.1.321.100.2.14.1.1.6 | INTEGER | read-write | disabled - Service does not return to the primary line until the backup line fails. enabled - Service automatically returns to the primary line when the primary line is able to carry service again. |
| INT netAPSConfigManualInhibit | 1.3.6.1.4.1.321.100.2.14.1.1.7 | INTEGER | read-write | Disabled - Neither line is manually inhibited from carrying service. ThisLine - This line is manually inhibited from carrying service. OtherLine - The other line is manually inhibited from carrying service. |
| INT netAPSConfigAvailabilityTimer | 1.3.6.1.4.1.321.100.2.14.1.1.8 | INTEGER | read-write | The line availability timer represents the minimum amount of time that is free of errors in active events that must expire before this line is returned to service availability. The timer is in seconds ranging from 0 - 900 seconds. |
| INT netAPSConfigESThreshold | 1.3.6.1.4.1.321.100.2.14.1.1.9 | INTEGER | read-write | This parameter is the number of erred seconds in a 15-minute period needed before a transfer request is triggered. A setting of zero disables this trigger. |
| INT netAPSConfigESCount | 1.3.6.1.4.1.321.100.2.14.1.1.10 | INTEGER | read-only | This parameter is the number of erred seconds in the current 15-minute interval. This count is reset at the beginning of a new 15-minute interval. |
| INT netAPSConfigESSwitchEvent | 1.3.6.1.4.1.321.100.2.14.1.1.11 | INTEGER | read-only | This status indicates if exceeding the ES threshold caused a transfer to the other line. |
| INT netAPSConfigCSESThreshold | 1.3.6.1.4.1.321.100.2.14.1.1.12 | INTEGER | read-write | This parameter is the number of consecutive SES needed before a transfer request is triggered. A setting of zero disables this trigger. |
| INT netAPSConfigCSESCount | 1.3.6.1.4.1.321.100.2.14.1.1.13 | INTEGER | read-only | This parameter is the number of consecutive SES detected. This count stops when 900 is reached and is reset when a non-SES is detected. |
| INT netAPSConfigCSESSwitchEvent | 1.3.6.1.4.1.321.100.2.14.1.1.14 | INTEGER | read-only | This status indicates if exceeding the consecutive SES threshold caused a transfer to the other line. |
| INT netAPSConfigStatusBitmap | 1.3.6.1.4.1.321.100.2.14.1.1.15 | INTEGER | read-only | TR54017 defined bitmap status for this line interface: Value is 1 if this line is carrying service. Value is 2 if this line is in a failed state. Value is 4 if this line is in an inhibit state. Value is 8 if this line is looped back. Value is 16 if the other line is in a failed state. Value is 32 if the other line is in an inhibit state. Value is 64 if the other line is looped back. Value is 128 if the manual inhibit is active Note that multiple status conditions may exist at the same time. The failed state is determined when carrier fails, or the ES threshold is reached, or the consecutive SES threshold is reached. The inhibit state is set when the manual inhibit setting affects this line or the line is inhibited by the remote end. |
| STR netAPSConfigStatusString | 1.3.6.1.4.1.321.100.2.14.1.1.16 | DisplayString | read-only | ASCII string version of netAPSConfigStatusBitmap for this line status bits |
| INT netAPSConfigTimeInInterval | 1.3.6.1.4.1.321.100.2.14.1.1.17 | INTEGER | read-only | The number of seconds into the netAPSHist24Table current interval. |
| INT netAPSConfigValidIntervals | 1.3.6.1.4.1.321.100.2.14.1.1.18 | INTEGER | read-only | The number of valid intervals in the netAPSHist24Table |
| INT netAPSConfigValidDays | 1.3.6.1.4.1.321.100.2.14.1.1.19 | INTEGER | read-only | The number of valid days in the netAPSHist30Table |
| INT netAPSConfigReset | 1.3.6.1.4.1.321.100.2.14.1.1.20 | INTEGER | read-write | This action parameter does the following when the given value is set: other - Does nothing clearAlarms - Clear the APS events and counts clearHistory - Clear the APS history table statistics |
| netAPSHist24Table | 1.3.6.1.4.1.321.100.2.14.2 | not-accessible | History table, contains Network APS historical data. | |
| netAPSHist24TableEntry | 1.3.6.1.4.1.321.100.2.14.2.1 | not-accessible | An entry in the netAPSHist24Table. | |
| INT netAPSHist24NearIndex | 1.3.6.1.4.1.321.100.2.14.2.1.1 | INTEGER | read-only | Selects the near device. |
| INT netAPSHist24FarIndex | 1.3.6.1.4.1.321.100.2.14.2.1.2 | INTEGER | read-only | Selects the far device. |
| INT netAPSHist24ifIndex | 1.3.6.1.4.1.321.100.2.14.2.1.3 | INTEGER | read-only | Selects the MIB-II ifIndex. |
| INT netAPSHist24Index | 1.3.6.1.4.1.321.100.2.14.2.1.4 | INTEGER | read-only | The index into the 24-hour history table. |
| TIK netAPSHist24Timestamp | 1.3.6.1.4.1.321.100.2.14.2.1.5 | TimeTicks | read-only | The value of sysUpTime when the statistics were last updated. |
| INT netAPSHist24StatusBitmap | 1.3.6.1.4.1.321.100.2.14.2.1.6 | INTEGER | read-only | TR54017 defined bitmap status for this line interface: Value is 1 if this line is carrying service. Value is 2 if this line is in a failed state. Value is 4 if this line is in an inhibit state. Value is 8 if this line is looped back. Value is 16 if the other line is in a failed state. Value is 32 if the other line is in an inhibit state. Value is 64 if the other line is looped back. Value is 128 if the manual inhibit is active Note that multiple status conditions may exist at the same time. The failed state is determined when carrier fails, or the ES threshold is reached, or the consecutive SES threshold is reached. The inhibit state is set when the manual inhibit setting affects this line or the line is inhibited by the remote end. |
| STR netAPSHist24StatusString | 1.3.6.1.4.1.321.100.2.14.2.1.7 | DisplayString | read-only | ASCII string version of netAPSHist24StatusBitmap for this line status bits |
| INT netAPSHist24Occurrences | 1.3.6.1.4.1.321.100.2.14.2.1.8 | INTEGER | read-only | This parameter is the total number of times the service was transferred between lines. |
| INT netAPSHist24Duration | 1.3.6.1.4.1.321.100.2.14.2.1.9 | INTEGER | read-only | This parameter is the number of seconds the service was provided on this line. |
| netAPSHist30Table | 1.3.6.1.4.1.321.100.2.14.3 | not-accessible | History table, contains Network APS 30-day historical data. | |
| netAPSHist30TableEntry | 1.3.6.1.4.1.321.100.2.14.3.1 | not-accessible | An entry in the netAPSHist30Table. | |
| INT netAPSHist30NearIndex | 1.3.6.1.4.1.321.100.2.14.3.1.1 | INTEGER | read-only | Selects the near device. |
| INT netAPSHist30FarIndex | 1.3.6.1.4.1.321.100.2.14.3.1.2 | INTEGER | read-only | Selects the far device. |
| INT netAPSHist30ifIndex | 1.3.6.1.4.1.321.100.2.14.3.1.3 | INTEGER | read-only | Selects the MIB-II ifIndex. |
| INT netAPSHist30Index | 1.3.6.1.4.1.321.100.2.14.3.1.4 | INTEGER | read-only | The index into the 30-day history table. |
| TIK netAPSHist30Timestamp | 1.3.6.1.4.1.321.100.2.14.3.1.5 | TimeTicks | read-only | The value of sysUpTime when the statistics were last updated. |
| INT netAPSHist30StatusBitmap | 1.3.6.1.4.1.321.100.2.14.3.1.6 | INTEGER | read-only | TR54017 defined bitmap status for this line interface: Value is 1 if this line is carrying service. Value is 2 if this line is in a failed state. Value is 4 if this line is in an inhibit state. Value is 8 if this line is looped back. Value is 16 if the other line is in a failed state. Value is 32 if the other line is in an inhibit state. Value is 64 if the other line is looped back. Value is 128 if the manual inhibit is active Note that multiple status conditions may exist at the same time. The failed state is determined when carrier fails, or the ES threshold is reached, or the consecutive SES threshold is reached. The inhibit state is set when the manual inhibit setting affects this line or the line is inhibited by the remote end. |
| STR netAPSHist30StatusString | 1.3.6.1.4.1.321.100.2.14.3.1.7 | DisplayString | read-only | ASCII string version of netAPSHist30StatusBitmap for this line status bits |
| INT netAPSHist30Occurrences | 1.3.6.1.4.1.321.100.2.14.3.1.8 | INTEGER | read-only | This parameter is the total number of times the service was transferred between lines. |
| INT netAPSHist30Duration | 1.3.6.1.4.1.321.100.2.14.3.1.9 | INTEGER | read-only | This parameter is the number of seconds the service was provided on this line. |
RFC description
Verilink DS8200v2 WAN device MIB covering interfaces, performance metrics, maintenance, and network APS management.
Start monitoring Verilink DS8200v2 digital switching/transport multiplexer with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.