DGS3450-L3MGMT-MIB

All MIBs › DGS3450-L3MGMT-MIB

Last Updated: 2012-03-02

Category: Technology: Routing/L3, Vendor: D-Link

Description: L3 management MIB for D-Link DGS-3450 switch covering routing protocols, ACLs, and Layer 3 management objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DGS3450-L3MGMT-MIB?

DGS3450-L3MGMT-MIB is a D-Link proprietary MIB defining Layer 3 network management information for the DGS-3450 managed switch. Its objects cover global RIP/OSPF/DVMRP/VRRP enable state and an IP-interface control table recording interface name/index, IP address/mask, associated VLAN, proxy-ARP, secondary-address flag, mode, admin state, and IPv6 link-local address/prefix/auto-state. As a configuration/status MIB it lets an administrator confirm an IP interface's routing-protocol participation and VLAN binding on a Layer 3 D-Link switch. It is deployed on the D-Link DGS-3450 managed switch. Engineers can download the DGS3450-L3MGMT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DGS3450-L3MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DGS-3450 managed switch

Monitoring Examples

An administrator checks swL3DevCtrlOSPFState alongside swL3IpCtrlIpAddr to confirm a routed VLAN interface is participating in OSPF as expected on a D-Link DGS-3450 switch.

What Can Be Monitored

Layer 3 routing-protocol enable state and IP interface configuration

Imported Objects

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
PhysAddress
RowStatus
TimeStamp
TruthValue

From SW34XXPRIMGMT-MIB

dgs3450

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL3MgmtMIB	1.3.6.1.4.1.171.11.70.3.3			The Structure of Layer 3 Network Management Information for the proprietary enterprise.
swL3DevMgmt	1.3.6.1.4.1.171.11.70.3.3.1
swL3DevCtrl	1.3.6.1.4.1.171.11.70.3.3.1.1
INT swL3DevCtrlRIPState	1.3.6.1.4.1.171.11.70.3.3.1.1.1	INTEGER	read-write	This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled.
swL3IpMgmt	1.3.6.1.4.1.171.11.70.3.3.2
swL3IpCtrlMgmt	1.3.6.1.4.1.171.11.70.3.3.2.1
swL3IpCtrlTable	1.3.6.1.4.1.171.11.70.3.3.2.1.3		not-accessible	This table contain IP interface information.
swL3IpCtrlEntry	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1		not-accessible	A list of information about a specific IP interface.
STR swL3IpCtrlInterfaceName	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.1	DisplayString	read-only	This object indicates the name of the IP interface.
INT swL3IpCtrlIfIndex	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.2	INTEGER	read-only	This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
IP swL3IpCtrlIpAddr	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.3	IpAddress	read-write	The IP address of the interface. This object only can take the value of the unicast IP address.
IP swL3IpCtrlIpSubnetMask	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.4	IpAddress	read-write	The IP net mask for this interface.
STR swL3IpCtrlVlanName	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.5	DisplayString	read-write	This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
INT swL3IpCtrlProxyArp	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.6	INTEGER	read-write	This object indicates enable/disable of the proxy ARP function for IPv4.
T/F swL3IpCtrlSecondary	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.7	TruthValue	read-write	When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.
INT swL3IpCtrlMode	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.8	INTEGER	read-write	This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server.
INT swL3IpCtrlAdminState	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.9	INTEGER	read-write	The state of the IP interface.
ADR swL3IpCtrlIpv6LinkLocalAddress	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.14	Ipv6Address	read-only	The IPv6 link local address for this interface.
INT swL3IpCtrlIpv6LinkLocalPrefixLen	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.15	INTEGER	read-only	The IPv6 prefix length for this IPv6 link local address.
ROW swL3IpCtrlState	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.16	RowStatus	read-create	This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
INT swL3IpCtrlIpv6LinkLocalAutoState	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.17	INTEGER	read-write	The state of the IPv6 link local auto.
INT swL3IpCtrlLocalProxyArp	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.18	INTEGER	read-create	If the state is enabled, the switch will be allowed to respond to the proxy ARP proxy ARP when the source IP and destination IP are on the same interface.
INT swL3IpCtrlDhcpv6ClientState	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.20	INTEGER	read-write	The state of the Dhcpv6 Client.
INT swL3IpCtrlIpDirectedBroadcastState	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.21	INTEGER	read-write	The state of the IP Directed Broadcast.
INT swL3IpCtrlIpDhcpOption12State	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.22	INTEGER	read-write	Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message.
STR swL3IpCtrlIpDhcpOption12HostName	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.23	DisplayString	read-write	Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12.
INT swL3IpCtrlDhcpv6ClientPDState	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.24	INTEGER	read-write	The state of the Dhcpv6 Client PD.
STR swL3IpCtrlDhcpv6ClientPDPrefixName	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.25	DisplayString	read-write	This object indicates the name for the DHCPv6 Client PD. If the swL3IpCtrlDhcpv6ClientPDState is disabled, this object will be clear and can't write.
ADR swL3IpCtrlDhcpv6ClientPDPrefix	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.26	Ipv6Address	read-only	The IPv6 prefix obtained form delegation router.
INT swL3IpCtrlDhcpv6ClientPDPrefixLen	1.3.6.1.4.1.171.11.70.3.3.2.1.3.1.27	INTEGER	read-only	The IPv6 prefix length for the prefix obtained from delegation router.
swL3Ipv6CtrlTable	1.3.6.1.4.1.171.11.70.3.3.2.1.4		not-accessible	This table contains IPv6 information of an IP interface.
swL3Ipv6CtrlEntry	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1		not-accessible	A list of IPv6 information about a specific IP interface.
STR swL3Ipv6CtrlInterfaceName	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.1	DisplayString	read-only	This object indicates the name of the IP interface.
INT swL3Ipv6CtrlMaxReassmblySize	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.2	INTEGER	read-only	Maximum Reassembly Size of the IP interface.
U32 swL3Ipv6CtrlNsRetransTimer	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.3	Unsigned32	read-write	Neighbor solicitation's retransmit timer. The unit is set in milliseconds.
INT swL3Ipv6CtrlRaState	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.5	INTEGER	read-write	Neighbor solicited state.
INT swL3Ipv6CtrlRaMinRtrAdvInterval	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.6	INTEGER	read-write	The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval
INT swL3Ipv6CtrlRaMaxRtrAdvInterval	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.7	INTEGER	read-write	The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.
INT swL3Ipv6CtrlRaLifeTime	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.8	INTEGER	read-write	Indicates the lifetime of the router as the default router.
INT swL3Ipv6CtrlRaReachableTime	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.9	INTEGER	read-write	Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.
U32 swL3Ipv6CtrlRaRetransTime	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.10	Unsigned32	read-write	Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.
INT swL3Ipv6CtrlRaHopLimit	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.11	INTEGER	read-write	Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.
INT swL3Ipv6CtrlRaManagedFlag	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.12	INTEGER	read-write	When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.
INT swL3Ipv6CtrlRaOtherConfigFlag	1.3.6.1.4.1.171.11.70.3.3.2.1.4.1.13	INTEGER	read-write	When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.
swL3Ipv6AddressCtrlTable	1.3.6.1.4.1.171.11.70.3.3.2.1.5		not-accessible	This table contain IPv6 address information for each IP interface.
swL3Ipv6AddressCtrlEntry	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1		not-accessible	A list of information about a specific IPv6 address.
STR swL3Ipv6AddressCtrlInterfaceName	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.1	DisplayString	read-only	This object indicates the name of the IP interface.
ADR swL3Ipv6Address	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.2	Ipv6Address	read-only	Specify the IPv6 address.
INT swL3Ipv6AddressCtrlPrefixLen	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.3	INTEGER	read-only	Indicates the prefix length of this IPv6 address.
U32 swL3Ipv6AddressCtrlPreferredLifeTime	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.4	Unsigned32	read-write	Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.
U32 swL3Ipv6AddressCtrlValidLifeTime	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.5	Unsigned32	read-write	Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.
INT swL3Ipv6AddressCtrlOnLinkFlag	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.6	INTEGER	read-write	When enabled, the address implied by the specified prefix is available on the link where the RA message is received.
INT swL3Ipv6AddressCtrlAutonomousFlag	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.7	INTEGER	read-write	When enabled, the specified prefix will be used to create an autonomous address configuration.
ROW swL3Ipv6AddressCtrlState	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.8	RowStatus	read-create	This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
INT swL3Ipv6AddressCtrlAddressType	1.3.6.1.4.1.171.11.70.3.3.2.1.5.1.9	INTEGER	read-only	This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement.
swL3Ipv6DHCPv6CPDAddrCtrlTable	1.3.6.1.4.1.171.11.70.3.3.2.1.6		not-accessible	This table contain the information of the IPv6 address which based on DHCPv6 client PD.
swL3Ipv6DHCPv6CPDAddrCtrlEntry	1.3.6.1.4.1.171.11.70.3.3.2.1.6.1		not-accessible	A list of information about a specific DHCPv6 Client PD IPv6 address.
STR swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName	1.3.6.1.4.1.171.11.70.3.3.2.1.6.1.1	DisplayString	read-only	This object indicates the name of the IP interface.
STR swL3Ipv6DHCPv6CPDAddrCtrlPrefixName	1.3.6.1.4.1.171.11.70.3.3.2.1.6.1.2	DisplayString	read-only	This object indicates the name of the prefix based on which the IPv6 address will be generate.
ADR swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr	1.3.6.1.4.1.171.11.70.3.3.2.1.6.1.3	Ipv6Address	read-only	Specify the suffix of the IPv6 address.
INT swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen	1.3.6.1.4.1.171.11.70.3.3.2.1.6.1.4	INTEGER	read-only	Indicates the prefix length of this IPv6 address.
ROW swL3Ipv6DHCPv6CPDAddrCtrlState	1.3.6.1.4.1.171.11.70.3.3.2.1.6.1.5	RowStatus	read-create	This variable displays the status of the entry. The status is used for creating and deleting instances of the objects in this table.
INT swL3IpCtrlAllIpIfState	1.3.6.1.4.1.171.11.70.3.3.2.1.7	INTEGER	read-write	This object indicates all interface function state of the device.
swL3IpFdbMgmt	1.3.6.1.4.1.171.11.70.3.3.2.2
swL3IpFdbInfoTable	1.3.6.1.4.1.171.11.70.3.3.2.2.1		not-accessible	A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
swL3IpFdbInfoEntry	1.3.6.1.4.1.171.11.70.3.3.2.2.1.1		not-accessible	Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
IP swL3IpFdbInfoIpAddr	1.3.6.1.4.1.171.11.70.3.3.2.2.1.1.1	IpAddress	read-only	A IP address for which switch has forwarding and/or filtering information.
IP swL3IpFdbInfoIpSubnetMask	1.3.6.1.4.1.171.11.70.3.3.2.2.1.1.2	IpAddress	read-only	A IP net mask for this interface.for which switch has forwarding and/or filtering information.
INT swL3IpFdbInfoPort	1.3.6.1.4.1.171.11.70.3.3.2.2.1.1.3	INTEGER	read-only	Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address.
INT swL3IpFdbInfoType	1.3.6.1.4.1.171.11.70.3.3.2.2.1.1.4	INTEGER	read-only	The status of this entry.
INT swL3IpArpAgingTime	1.3.6.1.4.1.171.11.70.3.3.2.4	INTEGER	read-write	The timeout period in minutes for aging out dynamically learned arp information.
swL3IpStaticRouteTable	1.3.6.1.4.1.171.11.70.3.3.2.5		not-accessible	This entity's IP static Routing table.
swL3IpStaticRouteEntry	1.3.6.1.4.1.171.11.70.3.3.2.5.1		not-accessible	A particular route to a particular destination, under a particular policy. Once an entry be built,it shouldn't be modified.That is,it just support create and delete action.
IP swL3IpStaticRouteDest	1.3.6.1.4.1.171.11.70.3.3.2.5.1.1	IpAddress	read-only	The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
IP swL3IpStaticRouteMask	1.3.6.1.4.1.171.11.70.3.3.2.5.1.2	IpAddress	read-only	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
INT swL3IpStaticRouteBkupState	1.3.6.1.4.1.171.11.70.3.3.2.5.1.3	INTEGER	read-only	The routing state for this route.The value SHOULD be primary(1) or backup(2).
IP swL3IpStaticRouteNextHop	1.3.6.1.4.1.171.11.70.3.3.2.5.1.4	IpAddress	read-create	On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0.
INT swL3IpStaticRouteMetric	1.3.6.1.4.1.171.11.70.3.3.2.5.1.5	INTEGER	read-create	The routing metric for this route.
INT swL3IpStaticRouteStatus	1.3.6.1.4.1.171.11.70.3.3.2.5.1.6	INTEGER	read-create	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table. active(4) - the nextHop of this entry exists in the ARP table. inActive(5) - the next hop of this entry does not exist in the ARP table.
swL3RelayMgmt	1.3.6.1.4.1.171.11.70.3.3.3
swL3RelayDhcpMgmt	1.3.6.1.4.1.171.11.70.3.3.3.1
INT swL3RelayDhcpState	1.3.6.1.4.1.171.11.70.3.3.3.1.1	INTEGER	read-write	This object indicates Dhcp Relay function is enabled or disabled.
INT swL3RelayDhcpHopCount	1.3.6.1.4.1.171.11.70.3.3.3.1.2	INTEGER	read-write	This object indicates the maximum number of router hops that the BOOTP packets can cross.
INT swL3RelayDhcpTimeThreshold	1.3.6.1.4.1.171.11.70.3.3.3.1.3	INTEGER	read-write	This object indicates the minimum time in seconds within which the switch must relay the Dhcp request. If this time is exceeded, the switch will drop the Dhcp packet.
swL3RelayDhcpCtrlTable	1.3.6.1.4.1.171.11.70.3.3.3.1.4		not-accessible	This table specifys the IP address as a destination to forward (relay) DHCP packets to.
swL3RelayDhcpCtrlEntry	1.3.6.1.4.1.171.11.70.3.3.3.1.4.1		not-accessible	A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.
STR swL3RelayDhcpCtrlInterfaceName	1.3.6.1.4.1.171.11.70.3.3.3.1.4.1.1	DisplayString	read-only	The name of the IP interface.
IP swL3RelayDhcpCtrlServer	1.3.6.1.4.1.171.11.70.3.3.3.1.4.1.2	IpAddress	read-only	The DHCP server IP address.
INT swL3RelayDhcpCtrlState	1.3.6.1.4.1.171.11.70.3.3.3.1.4.1.3	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
INT swL3RelayDhcpOption82State	1.3.6.1.4.1.171.11.70.3.3.3.1.5	INTEGER	read-write	This object indicates DHCP Relay Option 82 function is enabled or disabled.
INT swL3RelayDhcpOption82CheckState	1.3.6.1.4.1.171.11.70.3.3.3.1.6	INTEGER	read-write	This object indicates DHCP Relay Option 82 Check function is enabled or disabled.
INT swL3RelayDhcpOption82Policy	1.3.6.1.4.1.171.11.70.3.3.3.1.7	INTEGER	read-write	This object indicates DHCP Relay Option 82 Policy.
swL3DHCPRelayOption60	1.3.6.1.4.1.171.11.70.3.3.3.1.8
INT swL3DHCPRelayOption60State	1.3.6.1.4.1.171.11.70.3.3.3.1.8.1	INTEGER	read-write	This object indicates DHCP relay option 60 function is enabled or disabled.
INT swL3DHCPRelayOption60DefMode	1.3.6.1.4.1.171.11.70.3.3.3.1.8.2	INTEGER	read-write	This object indicates default mode that has no option 60 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption60DefRelayIp. drop(2): means to drop the packet.
swL3DHCPRelayOption60DefTable	1.3.6.1.4.1.171.11.70.3.3.3.1.8.3		not-accessible	This table indicates the default relay servers for the packet that has no option 60 mathcing rules.
swL3DHCPRelayOption60DefEntry	1.3.6.1.4.1.171.11.70.3.3.3.1.8.3.1		not-accessible	A list of information indicates the default relay servers for the packet that has no option 60 mathcing rules.
IP swL3DHCPRelayOption60DefRelayIp	1.3.6.1.4.1.171.11.70.3.3.3.1.8.3.1.1	IpAddress	read-only	This object indicates the IP address of default relay server.
ROW swL3DHCPRelayOption60DefRowStatus	1.3.6.1.4.1.171.11.70.3.3.3.1.8.3.1.2	RowStatus	read-create	This object indicates the status of this entry.
swL3DHCPRelayOption60Table	1.3.6.1.4.1.171.11.70.3.3.3.1.8.4		not-accessible	This table indicates the relay servers for the packet at option 60 rules.
swL3DHCPRelayOption60Entry	1.3.6.1.4.1.171.11.70.3.3.3.1.8.4.1		not-accessible	A list of information indicates the relay servers for the packet at option 60 rules.
STR swL3DHCPRelayOption60String	1.3.6.1.4.1.171.11.70.3.3.3.1.8.4.1.1	DisplayString	read-only	This object indicates string of this entry. Note that it is theoretically possible for a valid string to exceed the allowed length of an SNMP object identifier, and thus be impossible to represent in tables in this MIB that are indexed by string.
IP swL3DHCPRelayOption60RelayIp	1.3.6.1.4.1.171.11.70.3.3.3.1.8.4.1.2	IpAddress	read-only	This object indicates the IP address of relay server.
INT swL3DHCPRelayOption60MatchType	1.3.6.1.4.1.171.11.70.3.3.3.1.8.4.1.3	INTEGER	read-create	This object indicates match state of this entry. exact(1): means the option 60 string in the packet must full match with the specified string. partial(2): means the option 60 string in the packet only need partial match with the specified string.
ROW swL3DHCPRelayOption60RowStatus	1.3.6.1.4.1.171.11.70.3.3.3.1.8.4.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL3DHCPRelayOption61	1.3.6.1.4.1.171.11.70.3.3.3.1.9
INT swL3DHCPRelayOption61State	1.3.6.1.4.1.171.11.70.3.3.3.1.9.1	INTEGER	read-write	This object indicates DHCP relay option 61 function is enabled or disabled.
INT swL3DHCPRelayOption61DefMode	1.3.6.1.4.1.171.11.70.3.3.3.1.9.2	INTEGER	read-write	This object indicates default mode that has no option 61 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61DefRelayIp. drop(2): means to drop the packet.
IP swL3DHCPRelayOption61DefRelayIp	1.3.6.1.4.1.171.11.70.3.3.3.1.9.3	IpAddress	read-write	This object indicates the IP address of default relay server that has no option 61 mathcing rules. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'.
swL3DHCPRelayOption61Table	1.3.6.1.4.1.171.11.70.3.3.3.1.9.4		not-accessible	This table indicates the relay servers for the packet at option 61 rules.
swL3DHCPRelayOption61Entry	1.3.6.1.4.1.171.11.70.3.3.3.1.9.4.1		not-accessible	A list of information indicates the relay servers for the packet at option 61 rules.
INT swL3DHCPRelayOption61ClientType	1.3.6.1.4.1.171.11.70.3.3.3.1.9.4.1.1	INTEGER	read-only	This object indicates client type of this entry. mac(1): means the client-ID which is the MAC address of client. string(2): means the client-ID which is specified string by administrator.
STR swL3DHCPRelayOption61ClientID	1.3.6.1.4.1.171.11.70.3.3.3.1.9.4.1.2	DisplayString	read-only	This object indicates string of this entry. When swL3DHCPRelayOption61ClientType is mac(1), the format of this object should be XX-XX-XX-XX-XX-XX (MAC address). Note that it is theoretically possible for a valid string to exceed the allowed length of an SNMP object identifier, and thus be impossible to represent in tables in this MIB that are indexed by string.
INT swL3DHCPRelayOption61Mode	1.3.6.1.4.1.171.11.70.3.3.3.1.9.4.1.3	INTEGER	read-create	This object indicates mode of this entry. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61RelayIp. drop(2): means to drop the packet.
IP swL3DHCPRelayOption61RelayIp	1.3.6.1.4.1.171.11.70.3.3.3.1.9.4.1.4	IpAddress	read-create	This object indicates the IP address of relay server. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'.
ROW swL3DHCPRelayOption61RowStatus	1.3.6.1.4.1.171.11.70.3.3.3.1.9.4.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL3RelayDnsMgmt	1.3.6.1.4.1.171.11.70.3.3.3.2
INT swL3RelayDnsState	1.3.6.1.4.1.171.11.70.3.3.3.2.1	INTEGER	read-write	This object indicates DNS Relay function is enabled or disabled.
IP swL3RelayDnsPrimaryServer	1.3.6.1.4.1.171.11.70.3.3.3.2.2	IpAddress	read-write	This object indicates the address of the primary DNS server.
IP swL3RelayDnsSecondaryServer	1.3.6.1.4.1.171.11.70.3.3.3.2.3	IpAddress	read-write	This object indicates the address of the secondary DNS server.
INT swL3RelayDnsCacheState	1.3.6.1.4.1.171.11.70.3.3.3.2.4	INTEGER	read-write	This object indicates DNS Relay cache is enabled or disabled.
INT swL3RelayDnsStaticTableState	1.3.6.1.4.1.171.11.70.3.3.3.2.5	INTEGER	read-write	This object indicates DNS Relay static table is enabled or disabled.
swL3RelayDnsCtrlTable	1.3.6.1.4.1.171.11.70.3.3.3.2.6		not-accessible	This table display the current DNS relay static table.
swL3RelayDnsCtrlEntry	1.3.6.1.4.1.171.11.70.3.3.3.2.6.1		not-accessible	A list of information display the current DNS relay static table.
STR swL3RelayDnsCtrlDomainName	1.3.6.1.4.1.171.11.70.3.3.3.2.6.1.1	DisplayString	read-only	The domain name of the entry.
IP swL3RelayDnsCtrlIpAddr	1.3.6.1.4.1.171.11.70.3.3.3.2.6.1.2	IpAddress	read-only	The IP address of the entry.
INT swL3RelayDnsCtrlState	1.3.6.1.4.1.171.11.70.3.3.3.2.6.1.3	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
swL3RouteRedistriTable	1.3.6.1.4.1.171.11.70.3.3.5		not-accessible	Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the varios routers' routing tables and assigning appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol.
swL3RouteRedistriEntry	1.3.6.1.4.1.171.11.70.3.3.5.1		not-accessible	A list of information displaying the route redistribution table.
INT swL3RouteRedistriSrcProtocol	1.3.6.1.4.1.171.11.70.3.3.5.1.1	INTEGER	read-only	Allows the selection of the protocol of the source device.
INT swL3RouteRedistriDstProtocol	1.3.6.1.4.1.171.11.70.3.3.5.1.2	INTEGER	read-only	Allows the selection of the protocol of the destination device.
INT swL3RouteRedistriMetric	1.3.6.1.4.1.171.11.70.3.3.5.1.4	INTEGER	read-create	Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.
ROW swL3RouteRedistriRowStatus	1.3.6.1.4.1.171.11.70.3.3.5.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL3RoutePreference	1.3.6.1.4.1.171.11.70.3.3.9
INT swL3RoutePreferenceRIP	1.3.6.1.4.1.171.11.70.3.3.9.1	INTEGER	read-write	Used to configure the route preference of RIP.
INT swL3RoutePreferenceStatic	1.3.6.1.4.1.171.11.70.3.3.9.3	INTEGER	read-write	Used to configure the route preference of Static.
INT swL3RoutePreferenceLocal	1.3.6.1.4.1.171.11.70.3.3.9.4	INTEGER	read-only	Used to read the route preference of Local.
INT swL3RoutePreferenceDefault	1.3.6.1.4.1.171.11.70.3.3.9.8	INTEGER	read-write	Used to configure the route preference of Default.

RFC description

D-Link DGS3450 Layer-3 management MIB for the DGS3450 switch providing L3 routing and protocol configuration monitoring.

Start monitoring D-Link DGS-3450 managed switch (L3) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DGS3450-L3MGMT-MIB

What Is DGS3450-L3MGMT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description