All MIBs › CISCO-LWAPP-MESH-MIB › clMeshNodeBHDataRate
clMeshNodeBHDataRate
Module: CISCO-LWAPP-MESH-MIB
OID (symbolic): CISCO-LWAPP-MESH-MIB::clMeshNodeBHDataRate
OID (numeric): 1.3.6.1.4.1.9.9.616.1.1.1.1.15
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This object specifies the rate at which packets are sent on the backhaul link. Depending on the backhaul radio type, denoted by clMeshNodeBackhaul object, data rate will vary.
If the value of clMeshNodeBackhaul object is 'dot11a', data rates can be one of the following possible values. mbps6(4) mbps9(5) mbps12(7) mbps18(8) mbps24(9) mbps36(10) mbps48(11) mbps54(12) auto(13)
Additionally following data rates are supported if 802.11a supports 11n. htMcs0(14) htMcs1(15) htMcs2(16) htMcs3(17) htMcs4(18) htMcs5(19) htMcs6(20) htMcs7(21) htMcs8(22) htMcs9(23) htMcs10(24) htMcs11(25) htMcs12(26) htMcs13(27) htMcs14(28) htMcs15(29)
If the value of clMeshNodeBackhaul object is 'dot11b', then data rate can be one of the following possible values. mbps1(1) mbps2(2) mbps5point5(3) mbps11(6) auto(13)
If the value of clMeshNodeBackhaul object is 'dot11g', then data rate can be one of the following possible values. mbps1(1) mbps2(2) mbps5point5(3) mbps6(4) mbps9(5) mbps11(6) mbps12(7) mbps18(8) mbps24(9) mbps36(10) mbps48(11) mbps54(12) auto(13)
What is clMeshNodeBHDataRate?
Configures the data rate used on the mesh backhaul link; the set of valid rate values depends on which radio type is selected via clMeshNodeBackhaul.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.9.616.1.1.1.1.15 snmpwalk -v2c -c public <target> CISCO-LWAPP-MESH-MIB::clMeshNodeBHDataRate
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.9.616.1.1.1.1.15.1 snmpget -v2c -c public <target> CISCO-LWAPP-MESH-MIB::clMeshNodeBHDataRate.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.9.616.1.1.1.1.15.1 i <value>
Start monitoring Cisco wireless access points and controllers with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-LWAPP-MESH-MIB::clMeshNodeBHDataRate OID value, configure state conditions and alerts, and monitor any Cisco wireless access points and controllers from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.9 | ciscoMgmt | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.9.616 | ciscoLwappMeshMIB | CISCO-LWAPP-MESH-MIB |
| 1.3.6.1.4.1.9.9.616.1 | ciscoLwappMeshMIBObjects | CISCO-LWAPP-MESH-MIB |
| 1.3.6.1.4.1.9.9.616.1.1 | ciscoLwappMeshConfig | CISCO-LWAPP-MESH-MIB |
| 1.3.6.1.4.1.9.9.616.1.1.1 | clMeshNodeTable | CISCO-LWAPP-MESH-MIB |
| 1.3.6.1.4.1.9.9.616.1.1.1.1 | clMeshNodeEntry | CISCO-LWAPP-MESH-MIB |
| 1.3.6.1.4.1.9.9.616.1.1.1.1.15 | clMeshNodeBHDataRate | CISCO-LWAPP-MESH-MIB |