All MIBs › CISCO-ATM-IF-MIB › ciscoAtmIfIlmiAccessGlobalDefaultFilter
ciscoAtmIfIlmiAccessGlobalDefaultFilter
Module: CISCO-ATM-IF-MIB
OID (symbolic): CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessGlobalDefaultFilter
OID (numeric): 1.3.6.1.4.1.9.10.14.1.2
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: The global default access filter which set the per-switch default access filter for ILMI address registration on all interfaces. permitAll - This permits all ILMI registered addresses. permitPrefix - The address being registered by ILMI should have their prefix portion of the address match the ILMI prefixes used on this interface. If there are any per-interface ILMI address prefixes configured, then the prefixes derived from the switch addresses are not considered ILMI prefixes for this interface. permitPrefixAndWellknownGroups - This is same as 'permitPrefix' but in addition it also allows the well-known group addresses. The well-known group addresses will be the old LECS address and any address matching the ATM Forum address prefix for well known addresses. (i.e.,C5.0079.0000.0000.0000.0000.0000.00A03E) permitPrefixAndAllGroups - This is same as 'permitPrefix' but in addition it allows all group addresses.
What is ciscoAtmIfIlmiAccessGlobalDefaultFilter?
A read-write setting defining the switch-wide default ILMI address-registration access filter policy for all ATM interfaces (e.g. permit all addresses versus enforce a permitted prefix).
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.14.1.2 snmpwalk -v2c -c public <target> CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessGlobalDefaultFilter
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.14.1.2.1 snmpget -v2c -c public <target> CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessGlobalDefaultFilter.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.10.14.1.2.1 i <value>
Start monitoring Cisco ATM switch/router with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessGlobalDefaultFilter OID value, configure state conditions and alerts, and monitor any Cisco ATM switch/router from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.10 | ciscoExperiment | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.10.14 | ciscoAtmIfMIB | CISCO-ATM-IF-MIB |
| 1.3.6.1.4.1.9.10.14.1 | ciscoAtmIfMIBObjects | CISCO-ATM-IF-MIB |
| 1.3.6.1.4.1.9.10.14.1.2 | ciscoAtmIfIlmiAccessGlobalDefaultFilter | CISCO-ATM-IF-MIB |