All MIBs › CISCO-ATM-IF-MIB › ciscoAtmIfIlmiAccessFilter
ciscoAtmIfIlmiAccessFilter
Module: CISCO-ATM-IF-MIB
OID (symbolic): CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessFilter
OID (numeric): 1.3.6.1.4.1.9.10.14.1.1.1.34
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: The access filter which allows or denies certain ILMI registered addresses on this interface when ciscoAtmIfIlmiAddressRegistration is set to enable(1). permitAll - This permits all ILMI registered addresses. permitPrefix - The address being registered by ILMI should have their prefix portion of the address match the ILMI prefixes used on this interface. If there are any per-interface ILMI address prefixes configured, then the prefixes derived from the switch addresses are not considered ILMI prefixes for this interface. permitPrefixAndWellknownGroups - This is same as 'permitPrefix' but in addition it also allows the well-known group addresses. The well-known group addresses will be the old LECS address and any address matching the ATM Forum address prefix for well known addresses. (i.e.,C5.0079.0000.0000.0000.0000.0000.00A03E) permitPrefixAndAllGroups - This is same as 'permitPrefix' but in addition it allows all group addresses. useGlobalDefaultFilter - It indicates that this interface uses the per-switch global default filter
What is ciscoAtmIfIlmiAccessFilter?
Configures an access filter that permits or denies specific ILMI-registered addresses on this interface when ILMI address registration is enabled.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.14.1.1.1.34 snmpwalk -v2c -c public <target> CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessFilter
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.14.1.1.1.34.1 snmpget -v2c -c public <target> CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessFilter.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.10.14.1.1.1.34.1 i <value>
Start monitoring Cisco ATM switch/router with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-ATM-IF-MIB::ciscoAtmIfIlmiAccessFilter OID value, configure state conditions and alerts, and monitor any Cisco ATM switch/router from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.10 | ciscoExperiment | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.10.14 | ciscoAtmIfMIB | CISCO-ATM-IF-MIB |
| 1.3.6.1.4.1.9.10.14.1 | ciscoAtmIfMIBObjects | CISCO-ATM-IF-MIB |
| 1.3.6.1.4.1.9.10.14.1.1 | ciscoAtmIfTable | CISCO-ATM-IF-MIB |
| 1.3.6.1.4.1.9.10.14.1.1.1 | ciscoAtmIfEntry | CISCO-ATM-IF-MIB |
| 1.3.6.1.4.1.9.10.14.1.1.1.34 | ciscoAtmIfIlmiAccessFilter | CISCO-ATM-IF-MIB |