A3COM-HUAWEI-WIPS-MIB

All MIBs › A3COM-HUAWEI-WIPS-MIB

Organization: Hangzhou H3C Technologies Co., Ltd.

Last Updated: 2011-12-29

Category: VPN and Security, Vendor: H3C/HH3C, Wireless and WLAN

Description: Manages Wireless Intrusion Prevention System (WIPS) on H3C/3Com wireless infrastructure, providing rogue AP detection, countermeasure policy, and attack notification objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is A3COM-HUAWEI-WIPS-MIB?

A3COM-HUAWEI-WIPS-MIB is a joint 3Com/H3C (Huawei) vendor MIB for the Wireless Intrusion Prevention System (WIPS) feature on their wireless infrastructure, designed to detect and counter rogue access points and wireless attacks. It exposes global WIPS enable/policy configuration (sensor licensing, blocklist action, various aging/inactive timers, statistic/reclassification periods) alongside reset controls for trust, block, ignore, and countermeasure (ctm) device lists. Its monitoring/status value is focused on wireless security software health: whether WIPS is enabled and licensed with sufficient sensor capacity, how devices are being classified (trusted, blocked, ignored) over time, and whether reclassification/aging timers are tuned appropriately to avoid stale threat data, functioning as a security-monitoring layer rather than physical hardware status. It builds on the vendor's underlying wireless AP/controller infrastructure and sensor framework, without a strong dependency on separate standard MIBs evident from the description. It is typically deployed on H3C/3Com wireless LAN controllers and access points in enterprise environments requiring rogue-AP detection and wireless attack mitigation. Engineers can download the A3COM-HUAWEI-WIPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in A3COM-HUAWEI-WIPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C wireless LAN controller/access point
3Com wireless infrastructure

Monitoring Examples

A security administrator would check h3cWIPSEnable and h3cWIPSSensorLicenseNum to confirm WIPS is active and licensed for the deployed sensor count, and h3cWIPSBlocklistAction to know what countermeasure is applied to blocked devices. h3cWIPSAPInactiveTime and h3cWIPSSTAInactiveTime govern how long an AP or station can be silent before being aged out of tracking, while h3cWIPSStatisticPeriod and h3cWIPSReclassificationPeriod control how often threat statistics and device classifications are refreshed. The reset objects h3cWIPSResetAllTrustList/h3cWIPSResetAllBlockList/h3cWIPSResetAllIgnoreList/h3cWIPSResetAllCtmList would be invoked to clear accumulated classification state, for example after a wireless security policy change.

What Can Be Monitored

WIPS enable state
sensor license count
blocklist action policy
AP/station inactivity timers
reclassification period
trust/block/ignore/countermeasure list state

Imported Objects

From A3COM-HUAWEI-OID-MIB

h3cCommon

OBJECT-IDENTITY

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using h3cWIPSChlStatTotalPkt OID:

Select an H3C wireless controller or access point as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type h3cWIPSChlStatTotalPkt into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Represents the count of total frames in the channel. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
h3cWIPS	1.3.6.1.4.1.43.45.1.10.2.118			This MIB provides information about WIPS feature. Wireless Intrusion Prevention System (WIPS) WIPS is designed to be employed in an area that is serviced by an existing wireless network. It aids in the early detection of malicious outsider attacks and intrusions via wireless networks, and takes corresponding measures in order to guarantee the wireless environment security.
INT h3cWIPSAPAuthType	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.11	INTEGER	read-create	Represents the authentication type of the AP. undo - represents undo operation
ROW h3cWIPSAPClaRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.2	RowStatus	read-create	The status of this table entry.
h3cWIPSAPClaRuleEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1		not-accessible	Each entry contains information of each AP classification rule.
T/F h3cWIPSAPClaRuleMatchAll	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.4	TruthValue	read-create	Represents whether match all the AP classification sub-rules which have been configured.
OCT h3cWIPSAPClaRuleName	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.1	OCTET STRING	not-accessible	Represents the name of AP classification rule.
h3cWIPSAPClaRuleTable	1.3.6.1.4.1.43.45.1.10.2.118.1.3		not-accessible	The table defines the parameters for WIPS AP classification rule. One rule could be assigned to different VSDs.
U32 h3cWIPSAPClaSeverityLevel	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.3	Unsigned32	read-create	Represents the severity level of the AP classification rule. Available value limits from 0 to 100.
OCT h3cWIPSAPClaSubRuleSSID	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.8	OCTET STRING	read-create	Represents the SSID match template in the ap classification rule.
T/F h3cWIPSAPClaSubRuleSSIDCase	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.7	TruthValue	read-create	Represents the case sensitive or not for the SSID match. 'true': Case insensitive. 'false': Case sensitive.
INT h3cWIPSAPClaSubRuleSSIDOperator	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.6	INTEGER	read-create	Represents the compare way of the SSID in the sub rule, including include/not include/equal/not equal.
H3C h3cWIPSAPClaType	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.5	H3cWIPSAPClassifyType	read-create	Represents the type of AP classification.
I32 h3cWIPSAPInactiveTime	1.3.6.1.4.1.43.45.1.10.2.118.1.1.4	Integer32	read-write	Represents the time for AP getting inactive.
OCT h3cWIPSAtkDctPolicyBitString	1.3.6.1.4.1.43.45.1.10.2.118.1.4.2.1.3	OCTET STRING	read-create	Represents the bit string of attack detect policy configuration. The specific attack detect policy is enabled if its corresponding bit is set to 1; disabled if its corresponding bit is set to 0. bit0: adhoc bit1: ap-spoof bit2: client-spoof bit3: prohibited channel
h3cWIPSAtkDctPolicyCfgEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.4.2.1		not-accessible	Each entry contains information of each attack detect policy.
h3cWIPSAtkDctPolicyCfgGroup	1.3.6.1.4.1.43.45.1.10.2.118.1.4
ROW h3cWIPSAtkDctPolicyCfgRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.4.2.1.2	RowStatus	read-create	The status of this table entry.
OCT h3cWIPSAtkDctPolicyCfgSupportSet	1.3.6.1.4.1.43.45.1.10.2.118.1.4.1	OCTET STRING	read-only	Represents the bit string of supported attack detect policy. The specific attack detect policy is supported if its corresponding bit is set to 1; otherwise its corresponding bit is set to 0. bit0: adhoc bit1: ap-spoof bit2: client-spoof bit3: prohibited channel
h3cWIPSAtkDctPolicyCfgTable	1.3.6.1.4.1.43.45.1.10.2.118.1.4.2		not-accessible	The table defines the parameters for WIPS attack detect policy.
OCT h3cWIPSAtkDctPolicyName	1.3.6.1.4.1.43.45.1.10.2.118.1.4.2.1.1	OCTET STRING	not-accessible	Represents the name of attack detect policy.
INT h3cWIPSBlocklistAction	1.3.6.1.4.1.43.45.1.10.2.118.1.1.3	INTEGER	read-write	Represents whether the block list feature is enabled or not. 'block' : Enable the block list feature to filter unwanted devices. 'unblock' : Disable the block list feature.
h3cWIPSBlockListEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.8.1		not-accessible	Each entry contains block device MAC address information.
MAC h3cWIPSBlockListMacAddress	1.3.6.1.4.1.43.45.1.10.2.118.2.8.1.1	MacAddress	not-accessible	Represents the MAC address of block device.
INT h3cWIPSBlockListStatus	1.3.6.1.4.1.43.45.1.10.2.118.2.8.1.2	INTEGER	read-only	Represents the status of block device.
h3cWIPSBlockListTable	1.3.6.1.4.1.43.45.1.10.2.118.2.8		not-accessible	The table represents the list of block device MAC address.
h3cWIPSChannelEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.9.1		not-accessible	Each entry contains channel information.
T/F h3cWIPSChannelIsPermitted	1.3.6.1.4.1.43.45.1.10.2.118.2.9.1.3	TruthValue	read-only	Represents whether the channel is permitted.
TIK h3cWIPSChannelLastRptTm	1.3.6.1.4.1.43.45.1.10.2.118.2.9.1.4	TimeTicks	read-only	Represents the latest time that detecting the channel is active.
H3C h3cWIPSChannelNum	1.3.6.1.4.1.43.45.1.10.2.118.2.9.1.1	H3cWIPSChannel	not-accessible	Represents the channel number.
H3C h3cWIPSChannelRadioType	1.3.6.1.4.1.43.45.1.10.2.118.2.9.1.2	H3cWIPSRadioType	read-only	Represents the radio type used in the specific channel.
h3cWIPSChannelTable	1.3.6.1.4.1.43.45.1.10.2.118.2.9		not-accessible	The table represents the list of channel information.
C64 h3cWIPSChlStatAssocRequest	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.23	Counter64	read-only	Represents the count of association request frames in the channel.
C64 h3cWIPSChlStatAssocResponse	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.24	Counter64	read-only	Represents the count of association response frames in the channel.
C64 h3cWIPSChlStatAuthentication	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.27	Counter64	read-only	Represents the count of authentication frames in the channel.
C64 h3cWIPSChlStatBeacon	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.12	Counter64	read-only	Represents the count of beacon frames in the channel.
C64 h3cWIPSChlStatBmcastByte	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.6	Counter64	read-only	Represents the total length of broadcast and multicast frames in the channel.
C64 h3cWIPSChlStatBmcastPkt	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.5	Counter64	read-only	Represents the count of broadcast and multicast frames in the channel.
C64 h3cWIPSChlStatBroadcastDeauthen	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.29	Counter64	read-only	Represents the count of broadcast deauthentication frames in the channel.
C64 h3cWIPSChlStatBroadcastDisassoc	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.26	Counter64	read-only	Represents the count of broadcast disassociation frames in the channel.
H3C h3cWIPSChlStatChannel	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.2	H3cWIPSChannel	not-accessible	Represents the statistics channel.
C64 h3cWIPSChlStatControl	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.10	Counter64	read-only	Represents the count of control frames in the channel.
C64 h3cWIPSChlStatCTS	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.14	Counter64	read-only	Represents the count of CTS frames in the channel.
C64 h3cWIPSChlStatData	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.11	Counter64	read-only	Represents the count of data frames in the channel.
C64 h3cWIPSChlStatEapFailure	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.20	Counter64	read-only	Represents the count of EAP-Failure frames in the channel.
C64 h3cWIPSChlStatEapolLogoff	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.22	Counter64	read-only	Represents the count of EAPOL-Logoff frames in the channel.
C64 h3cWIPSChlStatEapolStart	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.21	Counter64	read-only	Represents the count of EAPOL-Start frames in the channel.
C64 h3cWIPSChlStatEapSuccess	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.19	Counter64	read-only	Represents the count of EAP-Success frames in the channel.
h3cWIPSChlStatEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1		not-accessible	Each entry contains information of channel statistics.
C64 h3cWIPSChlStatFragment	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.17	Counter64	read-only	Represents the count of fragment frames in the channel.
C64 h3cWIPSChlStatMalformed	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.30	Counter64	read-only	Represents the count of malformed frames in the channel.
C64 h3cWIPSChlStatManagement	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.9	Counter64	read-only	Represents the count of management frames in the channel.
C64 h3cWIPSChlStatProbeRequest	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.15	Counter64	read-only	Represents the count of probe request frames in the channel.
C64 h3cWIPSChlStatProbeResponse	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.16	Counter64	read-only	Represents the count of probe response frames in the channel.
C64 h3cWIPSChlStatRetry	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.18	Counter64	read-only	Represents the count of retry frames in the channel.
C64 h3cWIPSChlStatRTS	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.13	Counter64	read-only	Represents the count of RTS frames in the channel.
MAC h3cWIPSChlStatSensorMacAddr	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.1	MacAddress	not-accessible	Represents the MAC address of sensor.
h3cWIPSChlStatTable	1.3.6.1.4.1.43.45.1.10.2.118.2.13		not-accessible	The table represents the list of channel statistics information.
C64 h3cWIPSChlStatTotalByte	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.4	Counter64	read-only	Represents the length of total frames in the channel.
C64 h3cWIPSChlStatTotalPktEx	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.3	Counter64	read-only	Represents the count of total frames in the channel.
C64 h3cWIPSChlStatUnicastByte	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.8	Counter64	read-only	Represents the total length of unicast frames in the channel.
C64 h3cWIPSChlStatUnicastDeauthen	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.28	Counter64	read-only	Represents the count of unicast deauthentication frames in the channel.
C64 h3cWIPSChlStatUnicastDisassoc	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.25	Counter64	read-only	Represents the count of unicast disassociation frames in the channel.
C64 h3cWIPSChlStatUnicastPkt	1.3.6.1.4.1.43.45.1.10.2.118.2.13.1.7	Counter64	read-only	Represents the count of unicast frames in the channel.
h3cWIPSConfigGroup	1.3.6.1.4.1.43.45.1.10.2.118.1
h3cWIPSCountermeasureListEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.10.1		not-accessible	Each entry contains countermeasure device information.
h3cWIPSCountermeasureListTable	1.3.6.1.4.1.43.45.1.10.2.118.2.10		not-accessible	The table represents the list of countermeasure device information.
TIK h3cWIPSCtmListFirstTm	1.3.6.1.4.1.43.45.1.10.2.118.2.10.1.3	TimeTicks	read-only	Represents the first time that the device was countered since system is up.
H3C h3cWIPSCtmListLastestWorkChl	1.3.6.1.4.1.43.45.1.10.2.118.2.10.1.2	H3cWIPSChannel	read-only	Represents the channel on which the countermeasure device was working.
TIK h3cWIPSCtmListLastTm	1.3.6.1.4.1.43.45.1.10.2.118.2.10.1.4	TimeTicks	read-only	Represents the last time that the device was countered since system is up.
MAC h3cWIPSCtmListMacAddress	1.3.6.1.4.1.43.45.1.10.2.118.2.10.1.1	MacAddress	not-accessible	Represents the MAC address of the countered device.
I32 h3cWIPSCtmListQurCnt	1.3.6.1.4.1.43.45.1.10.2.118.2.10.1.5	Integer32	read-only	Represents how many times that the device was countered.
I32 h3cWIPSCtmListSensorNum	1.3.6.1.4.1.43.45.1.10.2.118.2.10.1.6	Integer32	read-only	Represents the number of sensors detecting the device.
T/F h3cWIPSDctAPAdd2BlackList	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.14	TruthValue	read-write	Represents whether the AP will be taken as a rogue AP. If the value is true, the MAC address will be automatically added into h3cWIPSBlockListTable and the category of the AP will be taken as rogue. If the value is false, nothing will be done. It will return false for get operation.
T/F h3cWIPSDctAPAdd2CtmList	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.17	TruthValue	read-write	Represents whether the AP will be taken as a countered AP. If the value is true, the MAC address will be automatically added into h3cWIPSCountermeasureListTable. If the value is false, nothing will be done. It will return false for get operation.
T/F h3cWIPSDctAPAdd2IgnoreList	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.16	TruthValue	read-write	Represents whether the AP will be taken as an ignored AP. If the value is true, the MAC address will be automatically added into h3cWIPSIgnoreListTable. If the value is false, nothing will be done. It will return false for get operation.
T/F h3cWIPSDctAPAdd2WhiteList	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.15	TruthValue	read-write	Represents whether the AP will be taken as an authorized AP. If the value is true, the MAC address will be automatically added into h3cWIPSTrustListTable. If the value is false, nothing will be done. It will return false for get operation.
h3cWIPSDctAPAttachStaEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.2.1		not-accessible	Each entry contains possible station information detected by WIPS.
MAC h3cWIPSDctAPAttachStaMac	1.3.6.1.4.1.43.45.1.10.2.118.2.2.1.1	MacAddress	not-accessible	Represents the MAC address of station associated with AP.
I32 h3cWIPSDctAPAttachStaNum	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.22	Integer32	read-only	Represents the number of clients associated with the detected AP.
ROW h3cWIPSDctAPAttachStaRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.2.2.1.2	RowStatus	read-only	The status of this table entry. It will return false for set operation.
h3cWIPSDctAPAttachStaTable	1.3.6.1.4.1.43.45.1.10.2.118.2.2		not-accessible	The table represents the list of station associated with APs detected by the WIPS.
H3C h3cWIPSDctAPAuthMethod	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.8	H3cWIPSAuthMethod	read-only	Represents the authentication method used by the detected AP. none(1) - No key management mode configured, psk(2) - pre-shared key authentication, dot1x(3) - 802.1x authentication. other(4) - other authentication.
MAC h3cWIPSDctAPBSSID	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.2	MacAddress	not-accessible	Represents the Basic Service Set.
H3C h3cWIPSDctAPCategory	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.18	H3cWIPSAPCategoryType	read-write	Represents the categorized result of the AP. For set operation, only the following values are valid: authorized(2),rogue(3),misconfigured(4),external(5)
H3C h3cWIPSDctAPCategoryWay	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.19	H3cWIPSDevCategoryWay	read-write	Represents by which way the AP is categorized. manual(1) -categorized by user autoByNMS(2) -categorized by NMS(Network Management System) autoByDev(3) -categorized by WIPS
H3C h3cWIPSDctAPEncryptMethod	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.9	H3cWIPSEncryptMethod	read-only	Represents the encrypt method used by the detected AP. none(1) - clear text or no cipher method is configure, wep(2) - WEP key, tkip(4) - WPA Temporal Key encryption, ccmp(8) - WPA AES CCMP encryption
h3cWIPSDctAPEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1		not-accessible	Each entry contains possible BSS information of each AP detected by WIPS.
TIK h3cWIPSDctAPFirstDctTm	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.13	TimeTicks	read-only	Represents the time that AP was detected for the first time since system is up.
T/F h3cWIPSDctAPIsCountered	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.5	TruthValue	read-only	Represents whether the detected AP is countered by WIPS.
TIK h3cWIPSDctAPLastDctTm	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.12	TimeTicks	read-only	Represents the time that AP was detected for the last time since system is up.
TIK h3cWIPSDctAPLastRptTm	1.3.6.1.4.1.43.45.1.10.2.118.2.3.1.4	TimeTicks	read-only	Represents the time that AP was detected by this sensor for the last time since system is up.
H3C h3cWIPSDctAPRadioType	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.7	H3cWIPSRadioType	read-only	Represents the radio type used by the detected AP.
I32 h3cWIPSDctAPRptRSSI	1.3.6.1.4.1.43.45.1.10.2.118.2.3.1.3	Integer32	read-only	Represents the current value of signal strength that WIPS sensor AP received from the AP.
h3cWIPSDctAPRptSensorEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.3.1		not-accessible	Each entry contains possible sensor information of WIPS.
OCT h3cWIPSDctAPRptSensorName	1.3.6.1.4.1.43.45.1.10.2.118.2.3.1.1	OCTET STRING	not-accessible	Represents the name of sensor.
I32 h3cWIPSDctAPRptSensorNum	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.23	Integer32	read-only	Represents the number of sensors detecting the AP.
I32 h3cWIPSDctAPRptSensorRadioId	1.3.6.1.4.1.43.45.1.10.2.118.2.3.1.2	Integer32	read-only	Represents on which radio the sensor AP detected the AP.
h3cWIPSDctAPRptSensorTable	1.3.6.1.4.1.43.45.1.10.2.118.2.3		not-accessible	The table represents the list of sensors.
TIK h3cWIPSDctAPRunningTime	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.3	TimeTicks	read-only	Represents the time since AP started to work, which is got from beacon/probe response frame.
TIK h3cWIPSDctAPRunTmLastUpdateTm	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.4	TimeTicks	read-only	Represents the time update h3cWIPSDctAPRunningTime since system is up.
H3C h3cWIPSDctAPSecurity	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.10	H3cWIPSAPSecurityType	read-only	Represents the security suites of the detected AP. clear 0x01 wpa2 0x02 wpa 0x04 wep 0x08
U32 h3cWIPSDctAPSeverityLevel	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.11	Unsigned32	read-only	Represents the severity level of the detected AP.
OCT h3cWIPSDctAPSSID	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.21	OCTET STRING	read-only	Represents the SSID broadcasted by AP.
H3C h3cWIPSDctAPStatus	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.20	H3cWIPSDevStatus	read-only	Represents the status of the AP detected by WIPS.
h3cWIPSDctAPTable	1.3.6.1.4.1.43.45.1.10.2.118.2.1		not-accessible	The table represents the list of possible BSS information for APs detected by the WIPS.
OCT h3cWIPSDctAPVSD	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.1	OCTET STRING	not-accessible	Represents the virtual security domain where the BSS was detected.
H3C h3cWIPSDctAPWorkChannel	1.3.6.1.4.1.43.45.1.10.2.118.2.1.1.6	H3cWIPSChannel	read-only	Represents the radio channel which the detected AP work on.
OCT h3cWIPSDctModeAPName	1.3.6.1.4.1.43.45.1.10.2.118.1.9.1.1	OCTET STRING	not-accessible	Represents the name of AP.
h3cWIPSDctModeEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.9.1		not-accessible	Each entry contains information of WIPS scanning mode on radio.
I32 h3cWIPSDctModeRadio	1.3.6.1.4.1.43.45.1.10.2.118.1.9.1.2	Integer32	not-accessible	Represents the radio of AP.
ROW h3cWIPSDctModeRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.9.1.4	RowStatus	read-create	The status of this table entry.
INT h3cWIPSDctModeScanMode	1.3.6.1.4.1.43.45.1.10.2.118.1.9.1.3	INTEGER	read-create	Represents the scanning mode. The radio enable-disable status must be disabled before WIPS scanning mode is configured on this radio. The mesh feature must be disabled before any WIPS scanning mode is set on radio. This radio can not apply any service template before the detectOnly scanning mode is set on the radio.
h3cWIPSDctModeTable	1.3.6.1.4.1.43.45.1.10.2.118.1.9		not-accessible	The table represents the list of AP scanning mode configuration on radio.
MAC h3cWIPSDctNetworkBSSID	1.3.6.1.4.1.43.45.1.10.2.118.2.7.1.1	MacAddress	not-accessible	Represents the Basic Service Set.
I32 h3cWIPSDctNetworkBSSNum	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.8	Integer32	read-only	Represents the number of APs using the same SSID in the ESS.
I32 h3cWIPSDctNetworkBSSStaNum	1.3.6.1.4.1.43.45.1.10.2.118.2.7.1.3	Integer32	read-only	Represents the number of clients associated with the detected BSS.
H3C h3cWIPSDctNetworkBSSWorkChl	1.3.6.1.4.1.43.45.1.10.2.118.2.7.1.2	H3cWIPSChannel	read-only	Represents on which radio channel that WIPS sensor AP detected the BSS.
U32 h3cWIPSDctNetworkCfg	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.3	Unsigned32	not-accessible	Represents the encrypt method, security suite and authentication method which are used by the detected ESS. The lowest 8 bits mean encrypt method. The higher 8 bits mean security suite. The third 8 bits stand for authentication method. The higerest 8 bits are reserved. The meaning is shown as follows: 31 23 15 7 0 + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + \| reserved \| auth method \| security suite\|encryptmethod\| + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + For encrypt method, the following values are supported: 1: none - clear text or no cipher method is configure, 2: wep - WEP key, 4: tkip - WPA Temporal Key encryption, 8: ccmp - WPA AES CCMP encryption For security suite, the following values are supported: 0x01: clear 0x02: wpa2 0x04: wpa 0x08: wep For authentication method, the following values are supported: 1: none - No key management mode configured, 2: psk - pre-shared key authentication, 3: dot1x - 802.1x authentication. 4: other - other authentication
TIK h3cWIPSDctNetworkFirstRptTm	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.4	TimeTicks	read-only	Represents the time that ESS was detected for the first time since system is up.
TIK h3cWIPSDctNetworkLastRptTm	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.5	TimeTicks	read-only	Represents the time that ESS was detected for the last time since system is up.
OCT h3cWIPSDctNetworkSSID	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.2	OCTET STRING	not-accessible	Represents the service set identifier for the ESS. Using the ASCII value '1' represents that the SSID is not advertised in the beacon frames.
T/F h3cWIPSDctNetworkSSIDHide	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.7	TruthValue	read-only	Represents whether the ESS broadcasted its SSID.
H3C h3cWIPSDctNetworkStatus	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.6	H3cWIPSDevStatus	read-only	Represents the status of this ESS detected by WIPS.
OCT h3cWIPSDctNetworkVSD	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1.1	OCTET STRING	not-accessible	Represents the virtual security domain in which the ESS was detected.
h3cWIPSDctSSIDBSSEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.7.1		not-accessible	Each entry contains possible BSS information of each AP detected by WIPS.
h3cWIPSDctSSIDBSSTable	1.3.6.1.4.1.43.45.1.10.2.118.2.7		not-accessible	The table represents the list of APs using the same SSID in the ESS.
h3cWIPSDctSSIDEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.6.1		not-accessible	Each entry contains possible ESS information of each ESS detected by WIPS.
h3cWIPSDctSSIDTable	1.3.6.1.4.1.43.45.1.10.2.118.2.6		not-accessible	The table represents the list of possible ESS information for networks detected by WIPS.
T/F h3cWIPSDctStaAdd2BlackList	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.9	TruthValue	read-write	Represents whether the station will be taken as a rogue station. If the value is true, the MAC address will be automatically added into h3cWIPSBlockListTable and the category of the station will be taken as rogue. If the value is false, nothing will be done. It will return false for get operation.
T/F h3cWIPSDctStaAdd2CtmList	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.12	TruthValue	read-write	Represents whether the station will be taken as a countered station. If the value is true, the MAC address will be automatically added into h3cWIPSCountermeasureListTable. If the value is false, nothing will be done. It will return false for get operation.
T/F h3cWIPSDctStaAdd2IgnoreList	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.11	TruthValue	read-write	Represents whether the station will be taken as an ignored station. If the value is true, the MAC address will be automatically added into h3cWIPSIgnoreListTable. If the value is false, nothing will be done. It will return false for get operation.
T/F h3cWIPSDctStaAdd2WhiteList	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.10	TruthValue	read-write	Represents whether the station will be taken as an authorized station. If the value is true, the MAC address will be automatically added into h3cWIPSTrustListTable. If the value is false, nothing will be done. It will return false for get operation.
MAC h3cWIPSDctStaAssocBSSID	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.3	MacAddress	read-only	Represents the BSSID which station associates with.
H3C h3cWIPSDctStaCategory	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.5	H3cWIPSClientCategoryType	read-only	Represents the categorized result of the station.
h3cWIPSDctStaEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1		not-accessible	Each entry contains possible station information of each station detected by WIPS.
TIK h3cWIPSDctStaFirstDctTm	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.13	TimeTicks	read-only	Represents the time that station was detected for the first time since system is up.
T/F h3cWIPSDctStaIsCountered	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.8	TruthValue	read-only	Represents whether the detected station is countered by WIPS.
TIK h3cWIPSDctStaLastDctTm	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.14	TimeTicks	read-only	Represents the time that station was detected for the last time since system is up.
TIK h3cWIPSDctStaLastRptTm	1.3.6.1.4.1.43.45.1.10.2.118.2.5.1.4	TimeTicks	read-only	Represents the time that station was detected by this sensor for the last time since system is up.
MAC h3cWIPSDctStaMac	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.2	MacAddress	not-accessible	Represents the MAC address of station.
H3C h3cWIPSDctStaRadioType	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.6	H3cWIPSRadioType	read-only	Represents the radio type used by the detected station.
I32 h3cWIPSDctStaRptRSSI	1.3.6.1.4.1.43.45.1.10.2.118.2.5.1.3	Integer32	read-only	Represents the current value of signal strength that WIPS sensor AP received from the station.
h3cWIPSDctStaRptSensorEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.5.1		not-accessible	Each entry contains possible sensor information of WIPS.
I32 h3cWIPSDctStaRptSensorNum	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.15	Integer32	read-only	Represents the number of sensors detecting the station.
I32 h3cWIPSDctStaRptSensorRadioId	1.3.6.1.4.1.43.45.1.10.2.118.2.5.1.2	Integer32	read-only	Represents on which radio the sensor AP detected the station.
h3cWIPSDctStaRptSensorTable	1.3.6.1.4.1.43.45.1.10.2.118.2.5		not-accessible	The table represents the list of sensors detecting the station.
OCT h3cWIPSDctStaRtpSensorName	1.3.6.1.4.1.43.45.1.10.2.118.2.5.1.1	OCTET STRING	not-accessible	Represents the name of sensor.
INT h3cWIPSDctStaState	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.16	INTEGER	read-only	Represents the authentication state of station with AP.
H3C h3cWIPSDctStaStatus	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.4	H3cWIPSDevStatus	read-only	Represents the status of this station detected by WIPS.
h3cWIPSDctStaTable	1.3.6.1.4.1.43.45.1.10.2.118.2.4		not-accessible	The table represents the list of possible information for stations detected by the WIPS.
OCT h3cWIPSDctStaVSD	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.1	OCTET STRING	not-accessible	Represents the virtual security domain in which the station was detected.
H3C h3cWIPSDctStaWorkChannel	1.3.6.1.4.1.43.45.1.10.2.118.2.4.1.7	H3cWIPSChannel	read-only	Represents on which radio channel that WIPS sensor AP detected the station.
h3cWIPSDetectGroup	1.3.6.1.4.1.43.45.1.10.2.118.2
I32 h3cWIPSDevAgingTime	1.3.6.1.4.1.43.45.1.10.2.118.1.1.6	Integer32	read-write	Represents the time for device getting aged.
H3C h3cWIPSDevStatChannel	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.3	H3cWIPSChannel	not-accessible	Represents the device working channel.
MAC h3cWIPSDevStatDevMacAddress	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.2	MacAddress	not-accessible	Represents the MAC address of the device detected by the sensor.
h3cWIPSDevStatEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1		not-accessible	Each entry contains information of device statistics.
C64 h3cWIPSDevStatRxAssoRequest	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.44	Counter64	read-only	Represents the count of association request frames received by the device in one channel.
C64 h3cWIPSDevStatRxAssoResponse	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.45	Counter64	read-only	Represents the count of association response frames received by the device in one channel.
C64 h3cWIPSDevStatRxAuth	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.47	Counter64	read-only	Represents the count of authentication frames received by the device in one channel.
C64 h3cWIPSDevStatRxCtrl	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.36	Counter64	read-only	Represents the count of control frames received by the device in one channel.
C64 h3cWIPSDevStatRxCTS	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.39	Counter64	read-only	Represents the count of CTS frames recieved by the device in one channel.
C64 h3cWIPSDevStatRxData	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.37	Counter64	read-only	Represents the count of data frames received by the device in one channel.
C64 h3cWIPSDevStatRxDeauth	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.48	Counter64	read-only	Represents the count of deauthentication frames received by the device in one channel.
C64 h3cWIPSDevStatRxDisassoc	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.46	Counter64	read-only	Represents the count of disassociation frames received by the device in one channel.
C64 h3cWIPSDevStatRxEAPFailure	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.50	Counter64	read-only	Represents the count of EAP-Failure frames received by the device in one channel.
C64 h3cWIPSDevStatRxEAPOLLogoff	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.52	Counter64	read-only	Represents the count of EAPOL-Logoff frames received by the device in one channel.
C64 h3cWIPSDevStatRxEAPOLStart	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.51	Counter64	read-only	Represents the count of EAPOL-Start frames received by the device in one channel.
C64 h3cWIPSDevStatRxEAPSuccess	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.49	Counter64	read-only	Represents the count of EAP-Success frames received by the device in one channel.
C64 h3cWIPSDevStatRxFragment	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.42	Counter64	read-only	Represents the count of fragment frames received by the device in one channel.
C64 h3cWIPSDevStatRxMalformed	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.53	Counter64	read-only	Represents the count of malformed frames received by the device in one channel.
C64 h3cWIPSDevStatRxMgmt	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.35	Counter64	read-only	Represents the count of management frames received by the device in one channel.
C64 h3cWIPSDevStatRxProbeRequest	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.40	Counter64	read-only	Represents the count of probe request frames received by the device in one channel.
C64 h3cWIPSDevStatRxProbeResponse	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.41	Counter64	read-only	Represents the count of probe response frames received by the device in one channel.
C64 h3cWIPSDevStatRxRetry	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.43	Counter64	read-only	Represents the count of retry frames received by the device in one channel.
C64 h3cWIPSDevStatRxRTS	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.38	Counter64	read-only	Represents the count of RTS frames recieved by the device in one channel.
C64 h3cWIPSDevStatRxTotalByte	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.32	Counter64	read-only	Represents the length of total frames received by the device in one channel.
C64 h3cWIPSDevStatRxTotalPkt	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.31	Counter64	read-only	Represents the count of total frames received by the device in one channel.
C64 h3cWIPSDevStatRxUnicastByte	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.34	Counter64	read-only	Represents the length of unicast frames received by the device in one channel.
C64 h3cWIPSDevStatRxUnicastPkt	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.33	Counter64	read-only	Represents the count of unicast frames received by the device in one channel.
MAC h3cWIPSDevStatSensorMacAddr	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.1	MacAddress	not-accessible	Represents the MAC address of sensor.
h3cWIPSDevStatTable	1.3.6.1.4.1.43.45.1.10.2.118.2.14		not-accessible	The table represents the list of device statistics information.
C64 h3cWIPSDevStatTxAssocRequest	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.19	Counter64	read-only	Represents the count of association request frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxAssocResponse	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.20	Counter64	read-only	Represents the count of association response frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxAuth	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.23	Counter64	read-only	Represents the count of authentication frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxBcastDeauth	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.25	Counter64	read-only	Represents the count of broadcast deauthentication frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxBcastDisassoc	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.22	Counter64	read-only	Represents the count of broadcast disassociation frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxBeacon	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.13	Counter64	read-only	Represents the count of beacon frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxBMcastByte	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.7	Counter64	read-only	Represents the length of broadcast and multicast frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxBMcastPkt	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.6	Counter64	read-only	Represents the count of broadcast and multicast frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxCtrl	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.11	Counter64	read-only	Represents the count of control frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxData	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.12	Counter64	read-only	Represents the count of data frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxEAPFailure	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.27	Counter64	read-only	Represents the count of EAP-Failure frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxEAPOLLogOff	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.29	Counter64	read-only	Represents the count of EAPOL-Logoff frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxEAPOLStart	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.28	Counter64	read-only	Represents the count of EAPOL-Start frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxEAPSuccess	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.26	Counter64	read-only	Represents the count of EAP-Success frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxFragment	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.17	Counter64	read-only	Represents the count of fragment frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxMalformed	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.30	Counter64	read-only	Represents the count of malformed frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxMgmt	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.10	Counter64	read-only	Represents the count of management frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxProbeRequest	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.15	Counter64	read-only	Represents the count of probe frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxProbeResponse	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.16	Counter64	read-only	Represents the count of probe response frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxRetry	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.18	Counter64	read-only	Represents the count of retry frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxRTS	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.14	Counter64	read-only	Represents the count of RTS frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxTotalByte	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.5	Counter64	read-only	Represents the length of total frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxTotalPkt	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.4	Counter64	read-only	Represents the count of total frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxUnicastByte	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.9	Counter64	read-only	Represents the length of unicast frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxUnicastDeauth	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.24	Counter64	read-only	Represents the count of unicast deauthentication frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxUnicastDisassoc	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.21	Counter64	read-only	Represents the count of unicast disassociation frames transmitted by the device in one channel.
C64 h3cWIPSDevStatTxUnicastPkt	1.3.6.1.4.1.43.45.1.10.2.118.2.14.1.8	Counter64	read-only	Represents the count of unicast frames transmitted by the device in one channel.
T/F h3cWIPSEnable	1.3.6.1.4.1.43.45.1.10.2.118.1.1.1	TruthValue	read-write	Represents whether the WIPS feature is enabled or not. 'true': enable the WIPS feature. 'false': disable the WIPS feature. WIPS and WIDS feature can not be enabled at the same time.
h3cWIPSGlobalConfigGroup	1.3.6.1.4.1.43.45.1.10.2.118.1.1
h3cWIPSIgnoreListCfgEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.8.1		not-accessible	Each entry contains information of each MAC address in the ignore list.
h3cWIPSIgnoreListCfgTable	1.3.6.1.4.1.43.45.1.10.2.118.1.8		not-accessible	The table provides the MAC address list of devices in the ignore list. WIPS will ignore the events caused by the device in the list.
h3cWIPSIgnoreListEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.11.1		not-accessible	Each entry contains ignored device information.
TIK h3cWIPSIgnoreListFirstIgnoreTm	1.3.6.1.4.1.43.45.1.10.2.118.2.11.1.2	TimeTicks	read-only	Represents the first time when the event caused by the device was ignored since system is up.
I32 h3cWIPSIgnoreListIgnoreCnt	1.3.6.1.4.1.43.45.1.10.2.118.2.11.1.4	Integer32	read-only	Represents the number of times of the event caused by device has been ignored.
TIK h3cWIPSIgnoreListLastIgnoreTm	1.3.6.1.4.1.43.45.1.10.2.118.2.11.1.3	TimeTicks	read-only	Represents the last time when the event caused by the device was ignored since system is up.
MAC h3cWIPSIgnoreListMAC	1.3.6.1.4.1.43.45.1.10.2.118.1.8.1.1	MacAddress	not-accessible	Represents the MAC address in ignore list.
MAC h3cWIPSIgnoreListMacAddress	1.3.6.1.4.1.43.45.1.10.2.118.2.11.1.1	MacAddress	not-accessible	Represents the MAC address of the ignored device.
ROW h3cWIPSIgnoreListRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.8.1.2	RowStatus	read-create	The status of this table entry.
h3cWIPSIgnoreListTable	1.3.6.1.4.1.43.45.1.10.2.118.2.11		not-accessible	The table represents the list of ignored device information.
U32 h3cWIPSMaxAPNum	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.16	Unsigned32	read-create	Represents the high-limit of the number of AP. Available value limits from 1 to 128.
U32 h3cWIPSMaxClientNum	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.18	Unsigned32	read-create	Represents the high-limit of the number of client. Available value limits from 1 to 128.
U32 h3cWIPSMaxDuration	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.14	Unsigned32	read-create	Represents the high-limit of the duration of AP. Available value limits from 1 to 2592000.
U32 h3cWIPSMaxRSSIValue	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.12	Unsigned32	read-create	Represents the high-limit of the RSSI of AP. Available value limits from 1 to 90.
U32 h3cWIPSMinAPNum	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.17	Unsigned32	read-create	Represents the low-limit of the number of AP. Available value limits from 0 to 127.
U32 h3cWIPSMinClientNum	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.19	Unsigned32	read-create	Represents the low-limit of the number of client. Available value limits from 0 to 127.
U32 h3cWIPSMinDuration	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.15	Unsigned32	read-create	Represents the low-limit of the duration of AP. Available value limits from 0 to 2591999.
U32 h3cWIPSMinRSSIValue	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.13	Unsigned32	read-create	Represents the low-limit of the RSSI of AP. Available value limits from 0 to 89.
h3cWIPSNotifyGroup	1.3.6.1.4.1.43.45.1.10.2.118.3
OCT h3cWIPSPermitChlBitMap	1.3.6.1.4.1.43.45.1.10.2.118.1.1.13	OCTET STRING	read-write	Represents the permit channel number by bitmap.
I32 h3cWIPSReclassificationPeriod	1.3.6.1.4.1.43.45.1.10.2.118.1.1.8	Integer32	read-write	Represents the period of WIPS reclassifying devices.
T/F h3cWIPSResetAllBlockList	1.3.6.1.4.1.43.45.1.10.2.118.1.1.10	TruthValue	read-write	This object is used to remove all entries from the static block list. It will return false for get operation.
T/F h3cWIPSResetAllCtmList	1.3.6.1.4.1.43.45.1.10.2.118.1.1.12	TruthValue	read-write	This object is used to remove all entries from the static countermeasure list. It will return false for get operation.
T/F h3cWIPSResetAllIgnoreList	1.3.6.1.4.1.43.45.1.10.2.118.1.1.11	TruthValue	read-write	This object is used to remove all entries from the ignore list. It will return false for get operation..
T/F h3cWIPSResetAllTrustList	1.3.6.1.4.1.43.45.1.10.2.118.1.1.9	TruthValue	read-write	This object is used to remove all entries from the static trust list. It will return false for get operation.
OCT h3cWIPSRule2VsdAPClaRuleNameCfg	1.3.6.1.4.1.43.45.1.10.2.118.1.2.2.1.1	OCTET STRING	not-accessible	Represents the name of AP classification rule attached to the VSD.
h3cWIPSRule2VsdEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.2.2.1		not-accessible	Each entry contains information of each AP classification rule in each VSD.
I32 h3cWIPSRule2VsdPrecedence	1.3.6.1.4.1.43.45.1.10.2.118.1.2.2.1.3	Integer32	read-create	Represents the precedence of AP classification rule attached to the VSD.
ROW h3cWIPSRule2VsdRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.2.2.1.2	RowStatus	read-create	The status of this table entry.
h3cWIPSRule2VsdTable	1.3.6.1.4.1.43.45.1.10.2.118.1.2.2		not-accessible	The table defines the AP classification rules been attached to the VSD.
H3C h3cWIPSSecurityType	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.9	H3cWIPSAPSecurityType	read-create	Represents the security type of active AP.
INT h3cWIPSSecurityTypeMatch	1.3.6.1.4.1.43.45.1.10.2.118.1.3.1.10	INTEGER	read-create	Represents match way of the security type of active AP.
h3cWIPSSensor2VsdEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.2.3.1		not-accessible	Each entry contains information of each sensor in each VSD.
ROW h3cWIPSSensor2VsdRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.2.3.1.2	RowStatus	read-create	The status of this table entry.
h3cWIPSSensor2VsdTable	1.3.6.1.4.1.43.45.1.10.2.118.1.2.3		not-accessible	The table defines the sensor been attached to the VSD.
U32 h3cWIPSSensorLicenseNum	1.3.6.1.4.1.43.45.1.10.2.118.1.1.2	Unsigned32	read-only	Represents the number of sensor license.
OCT h3cWIPSSensorNameCfg	1.3.6.1.4.1.43.45.1.10.2.118.1.2.3.1.1	OCTET STRING	not-accessible	Represents the name of sensor attached to the VSD.
h3cWIPSSensorRadioEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.2.4.1		not-accessible	Each entry contains information of a radio of a sensor.
I32 h3cWIPSSensorRadioRadioId	1.3.6.1.4.1.43.45.1.10.2.118.1.2.4.1.1	Integer32	not-accessible	Represents the radio identifier of the sensor.
INT h3cWIPSSensorRadioScanMode	1.3.6.1.4.1.43.45.1.10.2.118.1.2.4.1.2	INTEGER	read-only	Represents the scanning mode configured to the radio.
h3cWIPSSensorRadioTable	1.3.6.1.4.1.43.45.1.10.2.118.1.2.4		not-accessible	The table represents the list of sensor radio information.
INT h3cWIPSSensorState	1.3.6.1.4.1.43.45.1.10.2.118.1.2.3.1.3	INTEGER	read-create	Represents the running state of the sensor. It will return false for set operation.
I32 h3cWIPSSTAInactiveTime	1.3.6.1.4.1.43.45.1.10.2.118.1.1.5	Integer32	read-write	Represents the time for STA getting inactive.
h3cWIPSStaticBlockListCfgEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.6.1		not-accessible	Each entry contains information of each MAC address in the static block list.
h3cWIPSStaticBlockListCfgTable	1.3.6.1.4.1.43.45.1.10.2.118.1.6		not-accessible	The table provides the MAC address list of devices in the static block list. WIPS will ignore the frames from the devices in the list, and take the devices as rogue devices.
MAC h3cWIPSStaticBlockListMAC	1.3.6.1.4.1.43.45.1.10.2.118.1.6.1.1	MacAddress	not-accessible	Represents the MAC address in static block list.
ROW h3cWIPSStaticBlockListRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.6.1.2	RowStatus	read-create	The status of this table entry.
h3cWIPSStaticCtmListCfgEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.5.1		not-accessible	Each entry contains information of each MAC address in the static countermeasure list.
h3cWIPSStaticCtmListCfgTable	1.3.6.1.4.1.43.45.1.10.2.118.1.5		not-accessible	The table provides the MAC address list of devices in the static countermeasure list.
MAC h3cWIPSStaticCtmListMAC	1.3.6.1.4.1.43.45.1.10.2.118.1.5.1.1	MacAddress	not-accessible	Represents the MAC address in static countermeasure list.
ROW h3cWIPSStaticCtmListRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.5.1.2	RowStatus	read-create	The status of this table entry.
h3cWIPSStaticTrustListCfgEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.7.1		not-accessible	Each entry contains information of each MAC address in the static trust list.
h3cWIPSStaticTrustListCfgTable	1.3.6.1.4.1.43.45.1.10.2.118.1.7		not-accessible	The table provides the MAC address list of devices in the static trust list. WIPS will take the devices in the list as authorized devices.
MAC h3cWIPSStaticTrustListMAC	1.3.6.1.4.1.43.45.1.10.2.118.1.7.1.1	MacAddress	not-accessible	Represents the MAC address in static trust list.
ROW h3cWIPSStaticTrustListRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.7.1.2	RowStatus	read-create	The status of this table entry.
I32 h3cWIPSStatisticPeriod	1.3.6.1.4.1.43.45.1.10.2.118.1.1.7	Integer32	read-write	Represents the period of WIPS reporting the statistic.
h3cWIPSTrustListEntry	1.3.6.1.4.1.43.45.1.10.2.118.2.12.1		not-accessible	Each entry contains information of a trust device.
MAC h3cWIPSTrustListMacAddress	1.3.6.1.4.1.43.45.1.10.2.118.2.12.1.1	MacAddress	not-accessible	Represents the MAC address of the trust device.
INT h3cWIPSTrustListStatus	1.3.6.1.4.1.43.45.1.10.2.118.2.12.1.2	INTEGER	read-only	Represents the status of the trust device.
h3cWIPSTrustListTable	1.3.6.1.4.1.43.45.1.10.2.118.2.12		not-accessible	The table represents the list of trust device information.
OCT h3cWIPSVsdAtkDctPolicyNameCfg	1.3.6.1.4.1.43.45.1.10.2.118.1.2.1.1.3	OCTET STRING	read-create	Represents the name of attack detect policy attached to the VSD.
h3cWIPSVsdConfigGroup	1.3.6.1.4.1.43.45.1.10.2.118.1.2
h3cWIPSVsdEntry	1.3.6.1.4.1.43.45.1.10.2.118.1.2.1.1		not-accessible	Each entry contains information of each VSD.
OCT h3cWIPSVsdNameCfg	1.3.6.1.4.1.43.45.1.10.2.118.1.2.1.1.1	OCTET STRING	not-accessible	Represents the name of virtual security domain.
ROW h3cWIPSVsdRowStatus	1.3.6.1.4.1.43.45.1.10.2.118.1.2.1.1.2	RowStatus	read-create	The status of this table entry.
h3cWIPSVsdTable	1.3.6.1.4.1.43.45.1.10.2.118.1.2.1		not-accessible	The table provides the list of virtual security domain.

RFC description

Detects and manages wireless intrusion prevention, monitoring malicious AP activity.

Start monitoring H3C wireless controllers and APs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download A3COM-HUAWEI-WIPS-MIB