All MIBs › VIVOE-MIB › ethernetIfIpAddress
ethernetIfIpAddress
Module: VIVOE-MIB
OID (symbolic): VIVOE-MIB::ethernetIfIpAddress
OID (numeric): 1.3.6.1.4.1.35990.3.1.1.12.1.4
Node type: OBJECT-TYPE
Type: IpAddress
Access: read-write
Description: This is the statically assigned IP address of the interface on the device. An SNMP manager may change the IP address (if the device is in the maintenance mode) but the new value shall only become active after a reset or reboot. Def Stan 00-82 specifies the ranges from which the IP address shall be selected. The first entry in the table shall be designated as the primary interface with subsequent entries designated as secondary interfaces in a multi-interface device. All SNMP control on the device shall be undertaken using the primary interface. There is no requirement for the addresses of secondary interfaces to be on the same subnet as the primary address as long as the subnet masks are configured correctly. If the device is a service provider the last byte of the primary IP address shall also be used as the last byte of the multicast IP address that the device transmits on, as defined in Def Stan 00-82 Part 1.
What is ethernetIfIpAddress?
The statically assigned IP address of this interface; the first table entry is always the primary interface used for all SNMP control. Admins can change it while the device is in maintenance mode, but the new address only takes effect after a reset or reboot.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.35990.3.1.1.12.1.4 snmpwalk -v2c -c public <target> VIVOE-MIB::ethernetIfIpAddress
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.35990.3.1.1.12.1.4.1 snmpget -v2c -c public <target> VIVOE-MIB::ethernetIfIpAddress.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.35990.3.1.1.12.1.4.1 a <value>
Start monitoring military vehicle video-over-Ethernet endpoint, vetronics architecture (video-endpoint link/stream config status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the VIVOE-MIB::ethernetIfIpAddress OID value, configure state conditions and alerts, and monitor any military vehicle video-over-Ethernet endpoint, vetronics architecture (video-endpoint link/stream config status) from a single console.
OID Breakdown
Upper-level ancestors (6 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.35990 | desle | VIVOE-MIB |
| 1.3.6.1.4.1.35990.3 | desleProducts | VIVOE-MIB |
| 1.3.6.1.4.1.35990.3.1 | vivoeMIB | VIVOE-MIB |
| 1.3.6.1.4.1.35990.3.1.1 | deviceInfo | VIVOE-MIB |
| 1.3.6.1.4.1.35990.3.1.1.12 | ethernetIfTable | VIVOE-MIB |
| 1.3.6.1.4.1.35990.3.1.1.12.1 | ethernetIfEntry | VIVOE-MIB |
| 1.3.6.1.4.1.35990.3.1.1.12.1.4 | ethernetIfIpAddress | VIVOE-MIB |