Description:  
 This object specifies the argument to a command. The format of this  
 object is:

 octet[0]   contains command argument.
 octet[1]   contains Time-out value for Command in seconds.

 When umc1CommandId is _ReadTable_ and value of octet[0] is 10,20 & 
 120 than  Octet[2]   contains Terminal Id.

 Following table describes valid values of 0ctet[2] with its meaning.
 
  Value
 Octet[2]            Description
 ------------        ----------------------------------
    0                Read entire MIB Table
  1-33               Read all entries of MIB Table specified 
                     by Octet Zero of Command Arg that 
                     corresponds to given Terminal Id
 
 For a _ReadTable_ command the first octet is an argument. It identifies 
 the table that has to be read.  Any command type that is not explicitly
 listed below will ignore any value found in octet[0].

 Command Type        Valid Command Arguments 
 ------------        -----------------------
 _ReadTable_         Value    Description
                     0ctet[0]
                       10       Read umc1InventoryShelfTable
                                     
                       20       Read umc1InventoryPluginTable
                       30       Read umc1TerminalInfoTable
                       40       Read umc1TerminalSpanTable

                       50       Read umc1ACOSnapTopologyLinkTable
                       60       Read umc1TopologyLinkTable
                       70       Read umc1InventoryPluginTableChangeHistoryTable
                       80       Read umc1InventoryShelfTableChangeHistoryTable
                       90       Read umc1TerminalStatusTable
                       100      Read umc1CurAlmTable
                       110      Read umc1XCTable
                       120      Read umc1ShelfSpanTable
                       130      Read umc1GR303Table
                       140      Read umc1TR8Table
                       150      Read umc1AtmProtGrpTable
                       160      Read umc1PortProfTable
 _SetOrDelete_         10       Set/Delete umc1SystemSysProvCATable
 _ActivateAco_         1 or 2   ACO Type
 _CurTrafficStats_     0-33     Terminal Id
     
 The following table describes valid timeout values:

 Timeout Value       Description 
 octet[1]            The Timeout Value used by Agent
 --------------      -------------------------------------
     0               Use default timeout value 10 seconds.
     1-60            Use corresponding timeout value.
     61-255          Use maximum timeout value 60 seconds.

 For _SetOrDelete_ Command for umc1SystemSysProvCATable, the format of
 Command Argument is:

 octet[2]  Number of records to Set or Delete
 octet[3]  Length of Record (For Delete value of this octet is Zero.) 
 octet[4]  Db Specifier
 octet[5]  Plug-in Type
 octet[6]  Terminal Id.
 octet[7]  Icard Id.
 octet[8]  Channel Id ( Always 0)
 octet[9]  Mux Code
 octet[10] TxSgTCond
 octet[11] Chan Bits
 octet[12] Chan Bits 2

 For _ActivateAco_ Command, Following table describes Command Argument
 ACO Type.

 Value
 Octet[0]            Description
 --------            ----------------------
    1                CUI Standard ACO Operation
    2                CUI Extended ACO Operation

 For _AotRollover_, _GetVcStatusInfo_, and _GetBlockedVccInfo_ Command, 
 the format of Command Argument is:

 Octet[2-11]     represents Upstream end of the Bb cross-connect
     Octet[12-21]    represents Downstream end of the Bb cross-connect

 Octet[2]    Terminal Id
 Octet[3]    Shelf Id
 Octet[4]    Slot Id
 Octet[5]    Channel Id
 Octet[6]    Group Id
 Octet[7]    CRN Type
 Octet[8]    Bits 15..8 of VCI
 Octet[9]    Bits 7...0 of VCI
 Octet[10]   Bits 15..8 of VPI
 Octet[11]   Bits 7...0 of VPI
 Octet[12]   Terminal Id
 Octet[13]   Shelf Id
 Octet[14]   Slot Id
 Octet[15]   Channel Id
 Octet[16]   Group Id
 Octet[17]   CRN Type
 Octet[18]   Bits 15..8 of VCI
 Octet[19]   Bits 7...0 of VCI
 Octet[20]   Bits 15..8 of VPI
 Octet[21]   Bits 7...0 of VPI
 Octet[22]   Data Operation: Exact Get or Progressive Get (See DataOperation)
         Octet[23]   Crn64reqType:   0 for Plugin to Plugin request, 
                                 1 for group  to group  request
                                 2 both the above (retrieve any type)


 For _CurTrafficStats_ Command, the following table describes valid values 
 of 0ctet[0] with its meaning.

 Value
 Octet[0]            Description
 ------------        --------------------------------------------
    0                Get Current Traffic Status for all Terminals
  1-33               Get Current Traffic Status for specified 
                     Terminal Id
 
 --------------------------------------------------
 For _GetLineCardStatus_ Command, the format of
 Command Argument is:

 octet[2]    Terminal Id
 octet[3]    Shelf Id
 octet[4]    Slot Id
 octet[5]    Bits 15..8 of Plugin Type
 octet[6]    Bits 7...0 of Plugin Type
 octet[7]    Data Operation: Exact Get only (See DataOperation)
 octet[8]    Version (Argument List)

 Note: octet[8] definition.  The UMC1000 supports two unique response 
 data formats for this command.  When the version octet is not present,
 the SNMP host only support the original response data format.  A version 
 octet equal to 1 indicates the SNMP host supports both response data formats.  

 -------------------------------------------------------------------------
 For the _GetAtmBandwidth_ command, the format of the command argument is:

 octet[2]    Version
 octet[3]    Cac Data Type
 octet[4]    Terminal Id
 octet[5]    Location index 1
 octet[6]    Location index 2

 --------------------------------------------------------------------------
 For the _GetAtmStatistics_ command, the format of the command argument is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Shelf Id
 octet[5]    Slot Id
 octet[6]    Port: overloaded with Group Number for IMA 
 octet[7]    Data Operation: Exact Get or Write Data (Clear Statistics)
             (See DataOperation)

 ----------------------------------------------------------------------------
 For the _GetAdslBitsPerTone_ command, the format of the command argument is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Shelf Id
 octet[5]    Slot Id
 octet[6]    Circuit Id (Port Id)
 octet[7]    Bits 15..8 of Plugin Type
 octet[8]    Bits 7...0 of Plugin Type

 ----------------------------------------------------------------------------
 For the _GetAdslPmAttribute_ command, the format of the command argument is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Shelf Id
 octet[5]    Slot Id
 octet[6]    Circuit Id (Port ID) (0-6)
 octet[7]    ADSL PM Attribute ID / clear (reset type )
 octet[8]    Response format
 octet[9]    Data Operation: Exact Get, or Write Data (Clear PM) 
             (See DataOperation)
 octet[10]   Bits 15..8 of Plugin Type
 octet[11]   Bits 7...0 of Plugin Type

 Note: octet[7] definition. (ADSL PM Attribute ID)
   When octet[9] is equal 'GET EXACT'.
      Attribute enumerations as defined by UMC1000
   When octet[9] is equal 'WRITE'(clear).
      Type of clear, as defined by UMC1000

 Note: octet[8] definition.  Response format: 0 = Uncompressed, 
 1 = Compressed.

 Note: octet[9] (Data Operation) definition. 
   Data Operation = 'GET EXACT'
     The response data will contain a single record.  Valid range for 
     octet[6] is 1-6.  Valid range for octet[7] is 1-10.
   Data Operation = 'WRITE DATA'
     PM data is cleared for the specified port (octet[6] = 1-6) or 
     all ports (octet[6] = 0).  The valid range for octet[7] (0-2).

 -------------------------------------------------------------------------
 For the _GetPmDataBin_ command, the format of the command argument is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Shelf Id
 octet[5]    Slot Id
 octet[6]    Port ID (0 = all ports,1-6) for ADSL/OC3c/OC12c cards
             Group ID (0-3) for IMA card
 octet[7]    Number of ports supported at specified slot (1-6)
 octet[8]    Bin Type / Reset Type (0-2)
 octet[9]    Bits 31..24 of time (seconds since 1992)
 octet[10]   Bits 23..16 of time 
 octet[11]   Bits 15..8 of time
 octet[12]   Bits 7..0 of time
 octet[13]   Bits 15..8 of Plugin Type (supports ADSL family, OC3c/OC12c, IMA cards)
 octet[14]   Bits 7...0 of Plugin Type
 octet[15]   Data Operation: Get Exact, or Write Data (Clear PM) 
             (See DataOperation)
 octet[16]   ADSL (0), OC3c/Oc12c (1), or IMA (2) Card

 Note: 
 octet[6] definition.  Port Id is set to 1 for a OC3c/OC12c/IMA PIT type
 and 0 - 6 (0 - all ports) for an ADSL family PIT types.
 
 octet[8] definition.  For Data Operation equal Get Exact and Get 
 Progressive, Bin Type is set to 0 = 15 minute near-end(NE) section, 
 2 = daily NE section, 6 = 15 minute NE line, 
 7 = all 15 minute bins (pre system 9.0 release), 
 8 = daily NE line, 18 = 15-minute NE path, 20 = daily NE path,
 44 = 15-minute ATM, and 45 = daily ATM.
 For Data Operation equal Write Data (Clear PM), Reset Type set to 0 = 
 current data, 1 = current day data, 2 = all. 
 
 octet[15] definition. When Data Operation is 'GET EXACT', the response 
 data will contain a single record if the request is for a single port and
 a single bin, the response data will contain multiple records if the request 
 is for all ports and/or all bins (GET PROGRESIVE).
 When Data Operation is 'WRITE DATA', the command arguments specify a card.  
 PM data is cleared for all ports and all bins on the card.

 -------------------------------------------------------------------------
 For the _GetNBLinkStats_ command, the command argument list format is:

 octet[2]    Version
 octet[3]    Bits 31..24 of time (seconds since 1992)
 octet[4]    Bits 23..16 of time 
 octet[5]    Bits 15..8 of time
 octet[6]    Bits 7..0 of time
 octet[7]    Terminal End Point 1
 octet[8]    Terminal End Point 2
 octet[9]    Data Operation (Exact Get, or Progressive Get)
 octet[10]   GR303 group ID (1-3), Version 3 field only

 Note: 
 octet[2] represents the version of the request and expected response.
 This field set to (1) represents the original implementation.  This field
 set to (2) will lead to responses with additional fields for nailed-up DS0s.
 And, this field set to (3) requires octet[10], and retreives GR303 interface
 data on a per interface basis.

 octet[7], octet[8] and octet[10] definitions.  Terminal Endpoint 1 and 2 
 identify the endpoints of the link.   For a Get Exact Operation, data on 
 a single link will be retrieved, identified by the two terminal endpoints.
 For a Get Progressive Data Operation, terminal endpoints will represent 
 the starting point to retrieve data.  Both Terminal endpoints set to 1 will 
 indicate GR303 group data will be retrieved from the LET as specified by the 
 GR303 group ID, followed by narrowband CCS Data for each link in the system. 

 octet[9] definition. Data Operation will be set to Get Exact for retrieval 
 of a single link's data or Get Progressive for retrieval of all narrowband 
 CCS data. 

 -------------------------------------------------------------------------
 For the _DeleteEquipment_ command, the command argument list format is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Shelf Id
 octet[5]    Slot Id
 octet[6]    Bits 15..8 of Plugin Type
 octet[7]    Bits 7...0 of Plugin Type
 octet[8]    Control (0=query,1=delete)

 -------------------------------------------------------------------------
 For the _SoftwareActivation_ command, the cmd argument list format is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Shelf Id
 octet[5]    Slot Id
 octet[6]    Action (0=Activate standby bank,1=reset card)

 -------------------------------------------------------------------------
 For the _ManualProtectionSwitch_ command, the cmd argument list format is:

 octet[2]    Version
 octet[3]    Data Operation: Exact Get, or Write Data (Switch)
 octet[4]    Terminal Id
 octet[5]    Active Shelf Id
 octet[6]    Active Slot Id
 octet[7]    Standby Shelf Id    (not used with Exact Get)
 octet[8]    Standby Slot Id (not used with Exact Get)
 octet[9]    Bits 15..8 of Plugin Type
 octet[10]   Bits 7...0 of Plugin Type

 -------------------------------------------------------------------------
 For the _GetAPSInfo_ command, the cmd argument list format is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Protection Group Id

--------------------------------------------------------------------------
 For the _GenericIB_ command, the format of the command argument is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    IB Data Type (IxType)
 octet[5]    Operation (SNMP Get Exact, Get Progressive, or Put)
 octet[6]    IB Payload Length (maximun of 55 bytes)
 octet[7]    First byte of IB Payload
 octet[x]    Last byte of the IB Payload

 -------------------------------------------------------------------------
 For the _GetAtmStatsPerVcc_ command, the cmd argument list format is as
 follows.  This command is used to retrieve ATM statistics for a given
 channel from upto four circuit cards used to transport the channel. The 
 ATM channel is specified by the Uplink Channel Routing Number (CRN).  
 The CRN is uniquely identified using octets 3 through 12.  Four card 
 location identifier follow the CRN.  

   octet[2]    Version
   octet[3]    Terminal Id
   octet[4]    Shelf Id
   octet[5]    Slot Id
   octet[6]    Channel Id
   octet[7]    Group Id
   octet[8]    CRN Type
   octet[9]    Bits 15..8 of VCI
   octet[10]   Bits 7...0 of VCI
   octet[11]   Bits 15..8 of VPI
   octet[12]   Bits 7...0 of VPI

 Location of Primary Uplink circuit
 When uplink is T1 or T1x, provide location of uplink concentrator.
   octet[13]   Uplink Terminal Id
   octet[14]   Uplink Shelf Id
   octet[15]   Uplink Slot Id

 Location of Secondary Uplink circuit (if APS Group, set to 0xFF 
     if not provided)
   octet[16]   Uplink Terminal Id
   octet[17]   Uplink Shelf Id
   octet[18]   Uplink Slot Id

 Location of DSL circuit (or Downlink Group Primary)
   octet[19]   Downlink Terminal Id
   octet[20]   Downlink Shelf Id
   octet[21]   Downlink Slot Id

 Location of DSL concentration (or Downlink Group Secondary,
     optional, set to 0xFF if not provided)
   octet[22]   Downlink Terminal Id
   octet[23]   Downlink Shelf Id
   octet[24]   Downlink Slot Id

 -------------------------------------------------------------------------
 For the _GetDropTestResults_ command, the cmd argument list format is:

 octet[2]    Version
 octet[3]    Terminal Id
 octet[4]    Shelf Id
 octet[5]    Slot Id
 octet[6]    Circuit Id (Port Id)

 -------------------------------------------------------------------------