SENAO-ENTERPRISE-INDOOR-AP-CB-MIB

All MIBs › SENAO-ENTERPRISE-INDOOR-AP-CB-MIB

Organization: Senao R&D Dept., S/W Division

Last Updated: 2005-11-25

Category: Senao Wireless Access

Description: Manages Senao enterprise indoor wireless access point and client bridge configuration and association.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SENAO-ENTERPRISE-INDOOR-AP-CB-MIB?

SENAO-ENTERPRISE-INDOOR-AP-CB-MIB is a Senao enterprise MIB supplementing the standard IEEE 802.11 MIB with vendor-specific metrics for managing Senao enterprise indoor wireless access points and client bridges. It exposes configuration and association data for the AP/client-bridge role, such as radio settings and connected client/bridge associations, extending standard 802.11 management information. This MIB supports monitoring the operational status of the wireless radio and client associations, letting administrators track which clients or bridge links are currently associated and detect when an AP or bridge loses its expected connections. It explicitly depends on and supplements the IEEE 802.11 standard MIB rather than replacing it. It is deployed in enterprise indoor wireless deployments using Senao access points configured either as standard APs or as client bridges linking remote segments. Engineers can download the SENAO-ENTERPRISE-INDOOR-AP-CB-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SENAO-ENTERPRISE-INDOOR-AP-CB-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Senao enterprise indoor access point
Senao client bridge

Monitoring Examples

An administrator would monitor the AP's client/bridge association status to confirm expected devices remain connected, since an unexpected drop in associations would indicate a radio, interference, or configuration problem on that access point or client bridge link. No sample_objects were provided in the source, so specific object and table names are inferred from the module's stated purpose rather than confirmed directly.

What Can Be Monitored

client/bridge association status
802.11 radio configuration
AP operational state
wireless link connectivity

Imported Objects

From SNMPv2-SMI

Counter32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

DisplayString
MacAddress
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
ent802dot1xInfoEntry	1.3.6.1.4.1.14125.100.5.5.1		not-accessible	An entry in the ent802dot1xInfoTable.
ent802dot1xInfoTable	1.3.6.1.4.1.14125.100.5.5		not-accessible	This table provides one row for each 802.1x information. Each row contains the enterprise 802.1x information Table for that 802.1x information.
INT entAPMode	1.3.6.1.4.1.14125.100.5.1.3	INTEGER	read-write	Only when op mode is 0(AP), we can set AP mode: 0(AP), 1(WDS)
T/F entApplyModules	1.3.6.1.4.1.14125.100.1.12	TruthValue	write-only	Setting this attribute TRUE will apply the changed modules to reload
STR entAppVersion	1.3.6.1.4.1.14125.100.1.9	DisplayString	read-only	The version of the system application
INT entBand	1.3.6.1.4.1.14125.100.5.1.4	INTEGER	read-write	The wireless mode: 0(802.11 b/g), 1(802.11 b), 2(802.11 a), 4(802.11 g), 6(802.11 n), 7(802.11 g/n), 8(802.11 a/n), 9(802.11 b/g/n)
INT entBeaconInterval	1.3.6.1.4.1.14125.100.5.1.10	INTEGER	read-write	This attribute specifies the number of TU that a station shall use for scheduling Beacon transmissions
T/F entBroadcastESSID	1.3.6.1.4.1.14125.100.5.2.1.3	TruthValue	read-write	Set this attribute TRUE will enable the hidden SSID
INT entChannel	1.3.6.1.4.1.14125.100.5.1.6	INTEGER	read-write	The current operating frequency channel
INT entChannelBandwidth	1.3.6.1.4.1.14125.100.5.1.14	INTEGER	read-write	This attribute specifies the channel bandwidth: 0(Auto 20/40 MHZ), 1(20 MHZ)
OCT entCLConnectedTime	1.3.6.1.4.1.14125.100.5.6.1.7	OCTET STRING	read-write	The Client connected time
OCT entCLIdleTime	1.3.6.1.4.1.14125.100.5.6.1.8	OCTET STRING	read-write	The Client idle time
INT entCLInfoIndex	1.3.6.1.4.1.14125.100.5.6.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the ClientList information Table
OCT entCLInterface	1.3.6.1.4.1.14125.100.5.6.1.2	OCTET STRING	read-write	The Client connected SSID
OCT entCLMAC	1.3.6.1.4.1.14125.100.5.6.1.3	OCTET STRING	read-write	The Client MAC
OCT entCLRx	1.3.6.1.4.1.14125.100.5.6.1.4	OCTET STRING	read-write	The Rx value
INT entCLSignal	1.3.6.1.4.1.14125.100.5.6.1.6	INTEGER	read-write	The Client Wlan Signal
OCT entCLTx	1.3.6.1.4.1.14125.100.5.6.1.5	OCTET STRING	read-write	The Tx value
INT entCTSProtection	1.3.6.1.4.1.14125.100.5.1.16	INTEGER	read-write	This attribute specifies the CTS protection: 0(Auto), 1(Always), 2(None)
INT entDataRate	1.3.6.1.4.1.14125.100.5.1.7	INTEGER	read-write	This attribute specifies the data rate at which the station may transmit data in Mbps 0(Auto), 1(1Mbps), 2(2Mbps), 5(5.5Mbps), 11(11Mbps), 6(6Mbps), 9(9Mbps), 12(12Mbps), 18(18Mbps), 24(24Mbps), 36(36Mbps), 48(48Mbps), 54(54Mbps)
T/F entDHCPEnable	1.3.6.1.4.1.14125.100.2.4	TruthValue	read-write	When system mode is not 1(Repeater) and 5(WDS bridge), set this attribute TRUE will enable the DHCP server function of device
INT entDTIMPeriod	1.3.6.1.4.1.14125.100.5.1.11	INTEGER	read-write	This attribute specifies the number of beacon intervals
INT entEncryption	1.3.6.1.4.1.14125.100.5.2.1.5	INTEGER	read-write	The WLAN encryption: 0(none), 1(WEP), 2(TKIP), 3(AES), 4(TKIPAES)
OCT entESSID	1.3.6.1.4.1.14125.100.5.2.1.2	OCTET STRING	read-write	This attribute reflects the Service Set ID used in the Desired- SSID parameter of the most recent MLME_Scan.request
INT entESSIDNum	1.3.6.1.4.1.14125.100.5.1.5	INTEGER	read-write	Set the Number of multiple ESSID
INT entFragmentationThreshold	1.3.6.1.4.1.14125.100.5.1.12	INTEGER	read-write	This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY
STR entHwVersion	1.3.6.1.4.1.14125.100.1.6	DisplayString	read-only	The version of the hardware
INT entIPLeaseTime	1.3.6.1.4.1.14125.100.2.7	INTEGER	read-write	When system mode is not 1(Repeater) and 5(WDS bridge), the time period client can have the IP address assigned by DHCP server 0(half hour), 1(one hour) 2(two hours), 3(half day), 4(one day), 5(two days), 6(one week), 7(two weeks), 8(forever)
IP entIPPoolEnd	1.3.6.1.4.1.14125.100.2.6	IpAddress	read-write	When system mode is not 1(Repeater) and 5(WDS bridge), set the end address of DHCP IP pool
IP entIPPoolStart	1.3.6.1.4.1.14125.100.2.5	IpAddress	read-write	TWhen system mode is not 1(Repeater) and 5(WDS bridge), set the start address of DHCP IP pool
STR entKenelVersion	1.3.6.1.4.1.14125.100.1.8	DisplayString	read-only	The version of the kernel
entLAN	1.3.6.1.4.1.14125.100.2
IP entLANIP	1.3.6.1.4.1.14125.100.2.1	IpAddress	read-write	LAN IP address
entLanMacFilterEntry	1.3.6.1.4.1.14125.100.4.3.1		not-accessible	An entry in the entLanMacFilterTable.
T/F entLanMacFilteringEnable	1.3.6.1.4.1.14125.100.4.1	TruthValue	read-write	Set this attribute TRUE will enable the LAN MAC filtering
INT entLanMacFilteringMode	1.3.6.1.4.1.14125.100.4.2	INTEGER	read-write	The mode of LAN MAC filtering can be 0(white list), 1(black list)
entLanMacFilterTable	1.3.6.1.4.1.14125.100.4.3		not-accessible	This table provides one row for each LAN MAC filtering. Each row contains the enterprise LAN MAC filtering table for that LAN MAC filtering.
IP entLANSubnetMask	1.3.6.1.4.1.14125.100.2.2	IpAddress	read-write	LAN subnet mask
STR entMacAddress	1.3.6.1.4.1.14125.100.4.3.1.2	DisplayString	read-only	MAC address list in the LAN MAC filtering table
INT entMacAddressIndex	1.3.6.1.4.1.14125.100.4.3.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the LAN MAC Filtering Table
entMacFilter	1.3.6.1.4.1.14125.100.4
T/F entMacFilteringValid	1.3.6.1.4.1.14125.100.4.3.1.3	TruthValue	read-only	The validity status of each corresponding MAC address in LAN MAC filtering table
INT entNDataRate	1.3.6.1.4.1.14125.100.5.1.8	INTEGER	read-write	This attribute specifies the 11n data rate
INT entOpMode	1.3.6.1.4.1.14125.100.5.1.1	INTEGER	read-write	Set op mode: 0(AP), 1(Client bridge), 2(WDS bridge), 3(Repeater)
STR entPassword	1.3.6.1.4.1.14125.100.1.2	DisplayString	write-only	Administration password
INT entPreambleType	1.3.6.1.4.1.14125.100.5.1.15	INTEGER	read-write	This attribute specifies the preamble type: 1(Short), 2(Long)
STR entPresharedKey	1.3.6.1.4.1.14125.100.5.4.1.2	DisplayString	write-only	The WPA Pre-Shared key. (8~63 ASCII or 64 HEX)
T/F entRadio	1.3.6.1.4.1.14125.100.5.1.2	TruthValue	read-write	Set this attribute TRUE will enable the radio
IP entRADIUSServerIPAddress	1.3.6.1.4.1.14125.100.5.5.1.2	IpAddress	read-write	The address of RADIUS Server
STR entRADIUSServerPassword	1.3.6.1.4.1.14125.100.5.5.1.4	DisplayString	write-only	The password of RADIUS Server
INT entRADIUSServerPort	1.3.6.1.4.1.14125.100.5.5.1.3	INTEGER	read-write	The port of RADIUS Server
T/F entReset	1.3.6.1.4.1.14125.100.1.10	TruthValue	write-only	Setting this attribute TRUE causes the AP rebooted
T/F entResetToDefault	1.3.6.1.4.1.14125.100.1.11	TruthValue	write-only	Setting this attribute TRUE will Reboot the system and change settings to factory default
T/F entRouterEnable	1.3.6.1.4.1.14125.100.3.1	TruthValue	read-write	Only When op mode is 0(AP) or (Client bridge), can set this attribute. Set TRUE will enable the router.
INT entRTSThreshold	1.3.6.1.4.1.14125.100.5.1.13	INTEGER	read-write	This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed.
STR entSN	1.3.6.1.4.1.14125.100.1.7	DisplayString	read-only	Serial Number
entSNMP	1.3.6.1.4.1.14125.100.6
entSNMPCommunityEntry	1.3.6.1.4.1.14125.100.6.3.1		not-accessible	An entry in the entSNMPCommunityTable.
INT entSNMPCommunityIndex	1.3.6.1.4.1.14125.100.6.3.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the SNMP Community Table
STR entSNMPCommunityName	1.3.6.1.4.1.14125.100.6.3.1.2	DisplayString	read-write	The community name used to access SNMP device.
entSNMPCommunityTable	1.3.6.1.4.1.14125.100.6.3		not-accessible	This table provides one row for each SNMP community. Each row contains the enterprise SNMP community table for that SNMP community.
INT entSNMPCommunityType	1.3.6.1.4.1.14125.100.6.3.1.3	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the SNMP Community Table
T/F entSNMPCommunityValid	1.3.6.1.4.1.14125.100.6.3.1.4	TruthValue	read-only	Display the validity information of corresponding community index
T/F entSNMPStatus	1.3.6.1.4.1.14125.100.6.1	TruthValue	read-write	The status of current SNMP agent.0:disable, 1:Enable
entSNMPTrap	1.3.6.1.4.1.14125.100.6.4
INT entSNMPVerType	1.3.6.1.4.1.14125.100.6.2	INTEGER	read-write	The version of current SNMP agent.0:all, 1: v1, 2:v2c, 3:v3
T/F entSTPEnable	1.3.6.1.4.1.14125.100.2.3	TruthValue	read-write	Set this attribute TRUE will enable 802.1d Spanning Tree.
INT entSysMode	1.3.6.1.4.1.14125.100.1.4	INTEGER	read-only	System mode, 0:AP router, 1:Repeater, 2: AP bridge, 3: Client bridge, 4: Client router, 5: WDS bridge
STR entSysModel	1.3.6.1.4.1.14125.100.1.3	DisplayString	read-only	System model
entSystem	1.3.6.1.4.1.14125.100.1
entSystemTraps	1.3.6.1.4.1.14125.100.20.1
NTF entSystemTrapsReboot	1.3.6.1.4.1.14125.100.20.1.1			The trap is generated when the system is rebooted.
NTF entSystemTrapsReloadModules	1.3.6.1.4.1.14125.100.20.1.3			The trap is generated when the system modules are reloaded.
NTF entSystemTrapsRestoreToDefault	1.3.6.1.4.1.14125.100.20.1.2			The trap is generated when the default configuration of the system is restored.
TIK entSysUpTime	1.3.6.1.4.1.14125.100.1.5	TimeTicks	read-only	System uptime
STR entTrapReceiverCommunityName	1.3.6.1.4.1.14125.100.6.4.4	DisplayString	read-write	Specify the community name for SNMP manager to receive the trap report
IP entTrapReceiverIPAddress	1.3.6.1.4.1.14125.100.6.4.3	IpAddress	read-write	Specify the IP address(host) to receive the trap report
entTraps	1.3.6.1.4.1.14125.100.20
T/F entTrapStatus	1.3.6.1.4.1.14125.100.6.4.1	TruthValue	read-write	The trap status of current SNMP agent.0:disable, 1:Enable
INT entTrapVer	1.3.6.1.4.1.14125.100.6.4.2	INTEGER	read-write	The trap version of current SNMP agent.0:all, 1: v1, 2:v2c, 3:v3
INT entTxPower	1.3.6.1.4.1.14125.100.5.1.9	INTEGER	read-write	The transmit power level: 10(%), 25(%), 50(%), 75(%), 90(%), 100(%)
entWAN	1.3.6.1.4.1.14125.100.3
entWanTraps	1.3.6.1.4.1.14125.100.20.2
NTF entWanTrapsLinkDisconnect	1.3.6.1.4.1.14125.100.20.2.1			The trap is generated when the PHY of WAN is disconnected and it was connected.
NTF entWanTrapsLinkRecover	1.3.6.1.4.1.14125.100.20.2.2			The trap is generated when the PHY of WAN is connected and it was disconnected
entWlan	1.3.6.1.4.1.14125.100.5
T/F entWlan802dot1xEnable	1.3.6.1.4.1.14125.100.5.5.1.5	TruthValue	read-write	Set this attribute TRUE will enable 802.1x
INT entWlan802dot1xESSIDIndex	1.3.6.1.4.1.14125.100.5.5.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the 802.1x information Table
INT entWlanAuthenticationType	1.3.6.1.4.1.14125.100.5.2.1.6	INTEGER	read-write	The current authentication algorithms: 0 (openSystem), 1(wepAuto), 2(sharedKey), 3(WPAPSK), 4(WPA), 5(WPA2PSK), 6(WPA2), 7(WPA1WPA2), 8(WPA1PSKWPA2PSK)
entWlanClientListInfoEntry	1.3.6.1.4.1.14125.100.5.6.1		not-accessible	An entry in the entWlanClientListInfoTable.
entWlanClientListInfoTable	1.3.6.1.4.1.14125.100.5.6		not-accessible	This table provides one row for Wlan client list information.
entWlanCommonInfo	1.3.6.1.4.1.14125.100.5.1
INT entWlanESSIDIndex	1.3.6.1.4.1.14125.100.5.3.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the WEP information Table
entWlanESSIDInfoEntry	1.3.6.1.4.1.14125.100.5.2.1		not-accessible	An entry in the entWlanESSIDInfoTable.
INT entWlanESSIDInfoIndex	1.3.6.1.4.1.14125.100.5.2.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the ESSID information Table
entWlanESSIDInfoTable	1.3.6.1.4.1.14125.100.5.2		not-accessible	This table provides one row for each ESSID information. Each row contains the enterprise ESSID information Table for that ESSID information.
entWlanWepInfoEntry	1.3.6.1.4.1.14125.100.5.3.1		not-accessible	An entry in the entWlanWepInfoTable.
entWlanWepInfoTable	1.3.6.1.4.1.14125.100.5.3		not-accessible	This table provides one row for each WEP information. Each row contains the enterprise WEP information Table for that WEP information.
OCT entWlanWepKey1Value	1.3.6.1.4.1.14125.100.5.3.1.3	OCTET STRING	read-write	Set key1 string. (5 or 13 ASCCI characters, 10 or 26 hex numbers)
OCT entWlanWepKey2Value	1.3.6.1.4.1.14125.100.5.3.1.4	OCTET STRING	read-write	Set key2 string. (5 or 13 ASCCI characters, 10 or 26 hex numbers)
OCT entWlanWepKey3Value	1.3.6.1.4.1.14125.100.5.3.1.5	OCTET STRING	read-write	Set key3 string. (5 or 13 ASCCI characters, 10 or 26 hex numbers)
OCT entWlanWepKey4Value	1.3.6.1.4.1.14125.100.5.3.1.6	OCTET STRING	read-write	Set key4 string. (5 or 13 ASCCI characters, 10 or 26 hex numbers)
INT entWlanWepKeyID	1.3.6.1.4.1.14125.100.5.3.1.2	INTEGER	read-write	This attribute shall indicate the use of the first, second, third, or fourth element of the WEPDefaultKeys array
INT entWlanWPAESSIDIndex	1.3.6.1.4.1.14125.100.5.4.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of columnar objects in the WPA information Table
entWlanWPAInfoEntry	1.3.6.1.4.1.14125.100.5.4.1		not-accessible	An entry in the entWlanWPAInfoTable.
entWlanWPAInfoTable	1.3.6.1.4.1.14125.100.5.4		not-accessible	This table provides one row for each WPA information. Each row contains the enterprise WPA information Table for that WPA information.
T/F entWMM	1.3.6.1.4.1.14125.100.5.2.1.4	TruthValue	read-write	Set this attribute TRUE will enable WMM
indoorWirelessDevice	1.3.6.1.4.1.14125.100
senao	1.3.6.1.4.1.14125			The MIB module defines Senao implementation-specific metrics useful in managing IEEE 802.11 on Senao devices. This is used as a supplement to the standard 802.11 MIB proposed by IEEE.

RFC description

Manages IEEE 802.11 wireless configuration for Senao access points and cellular base stations. Supplements standard 802.11 MIB with implementation-specific metrics.

Start monitoring Senao enterprise indoor access point, Senao client bridge (802.11 radio/client-association status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SENAO-ENTERPRISE-INDOOR-AP-CB-MIB

What Is SENAO-ENTERPRISE-INDOOR-AP-CB-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description