All MIBs › PEA-EQUIPMENT-FELX › ifBandwidthMeasurementPeriod
ifBandwidthMeasurementPeriod
Module: PEA-EQUIPMENT-FELX
OID (symbolic): PEA-EQUIPMENT-FELX::ifBandwidthMeasurementPeriod
OID (numeric): 1.3.6.1.4.1.193.72.800.10.3.2
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: The bandwidth threshold function is used to monitor the average bandwidth over the ifBandwidthMeasurementPeriod on each of the device's external interfaces. If the measured average bandwidth (in percents to the maximum possible bandwidth on this particular interface) reaches the ifBandwidthUsageThreshold (given also in percents), the ifBandwidthUsageThresholdNotification is sent. Likewise, when the next measurement period with the average bandwidth lower than the ifBandwidthUsageThreshold is encountered, the ifBandwidthUsageThresholdCeasingNotification is sent.
This defines the measurement period for the bandwidth threshold function. The period is expressed in minutes. The minimum possible value is 1 minute. The maximum possible value is limited by the size of a 32-bit integer (i.e. virtually unlimited). The value of 0 turns the function off.
Setting this to a value different from the current value results in all the measurement counters being cleared and all active threshold notifications being ceased.
What is ifBandwidthMeasurementPeriod?
Sets, in minutes, how long the bandwidth-threshold monitor averages traffic on each external interface before comparing it against ifBandwidthUsageThreshold; setting it to 0 disables the feature, and changing the value resets all measurement counters and clears any active threshold alarms.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.193.72.800.10.3.2 snmpwalk -v2c -c public <target> PEA-EQUIPMENT-FELX::ifBandwidthMeasurementPeriod
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.193.72.800.10.3.2.1 snmpget -v2c -c public <target> PEA-EQUIPMENT-FELX::ifBandwidthMeasurementPeriod.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.193.72.800.10.3.2.1 i <value>
Start monitoring Ericsson Diax FELX Ethernet switch card, IP DSLAM equipment module (hardware inventory) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the PEA-EQUIPMENT-FELX::ifBandwidthMeasurementPeriod OID value, configure state conditions and alerts, and monitor any Ericsson Diax FELX Ethernet switch card, IP DSLAM equipment module (hardware inventory) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.193 | ericsson | ANS-COMMON-MIB |
| 1.3.6.1.4.1.193.72 | diaxMIB | DXD-SMI |
| 1.3.6.1.4.1.193.72.800 | peaFelx | PEA-FELX-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.193.72.800.10 | peaEquipmentFelx | PEA-EQUIPMENT-FELX |
| 1.3.6.1.4.1.193.72.800.10.3 | ifObjects | PEA-EQUIPMENT-FELX |
| 1.3.6.1.4.1.193.72.800.10.3.2 | ifBandwidthMeasurementPeriod | PEA-EQUIPMENT-FELX |