All MIBs › JNX-PPPOE-MIB › jnxPPPoESubIfRowStatus
jnxPPPoESubIfRowStatus
Module: JNX-PPPOE-MIB
OID (symbolic): JNX-PPPOE-MIB::jnxPPPoESubIfRowStatus
OID (numeric): 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.2
Node type: OBJECT-TYPE
Type: RowStatus
Access: read-only
Description: Controls creation/deletion of entries in this table with READ-CREATE maximum access ,according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPPPoESubIfRowStatus jnxPPPoESubIfLowerIfIndex
In addition, when creating an entry the following conditions must hold: A value for jnxPPPoESubIfIndex must have been determined previously, by reading jnxPPPoESubIfNextIfIndex.
The interface identified by jnxPPPoESubIfLowerIfIndex must exist, and must be a PPPoEinterface.
A positive value configured for jnxPPPoESubIfId must not already be assigned to another subinterface layered onto the same underlying PPPoEinterface.
A corresponding entry in ifTable/ifXTable/jnxIfTable is created or destroyed as a result of creating or destroying an entry in this table.
The following values can be read from this object: active(1)
What is jnxPPPoESubIfRowStatus?
This OID controls creating or deleting a row in the PPPoE subinterface table, restricted to createAndGo and destroy on write with active(1) the only value read back. Creating a subinterface here also creates matching entries in ifTable/ifXTable, and requires jnxPPPoESubIfLowerIfIndex to already point at a valid PPPoE interface.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.2 snmpwalk -v2c -c public <target> JNX-PPPOE-MIB::jnxPPPoESubIfRowStatus
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.2.1 snmpget -v2c -c public <target> JNX-PPPOE-MIB::jnxPPPoESubIfRowStatus.1
Start monitoring Juniper Networks MX-series broadband network gateway with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the JNX-PPPOE-MIB::jnxPPPoESubIfRowStatus OID value, configure state conditions and alerts, and monitor any Juniper Networks MX-series broadband network gateway from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.2636 | juniperMIB | JUNIPER-SMI |
| 1.3.6.1.4.1.2636.3 | jnxMibs | JUNIPER-SMI |
| 1.3.6.1.4.1.2636.3.67 | jnxPppoeMibRoot | JUNIPER-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.2636.3.67.1 | jnxPPPoEMIB | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1 | jnxPPPoEObjects | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.2 | jnxPPPoESubIfLayer | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.2.2 | jnxPPPoESubIfTable | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.2.2.1 | jnxPPPoESubIfEntry | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.2.2.1.2 | jnxPPPoESubIfRowStatus | JNX-PPPOE-MIB |