All MIBs › JNX-PPPOE-MIB › jnxPPPoEIfLockoutMin
jnxPPPoEIfLockoutMin
Module: JNX-PPPOE-MIB
OID (symbolic): JNX-PPPOE-MIB::jnxPPPoEIfLockoutMin
OID (numeric): 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.12
Node type: OBJECT-TYPE
Type: Integer32
Access: read-only
Description: The lower bound, in seconds, of the time range used to specify the duration of the lockout of the client from recognition for the specified interface. This only takes effect if jnxPPPoEIfAutoconfig is set for this interface.
The ability to lockout the client in the event of an error in creating a PPP interface is enabled by default. The initial lockout duration is this object's value and increases exponentially for each failure that occurs for the client creating a PPP interface for the PPPoEinterface within the greater of 15 minutes and jnxPPPoEIfLockoutMax.
The lockout duration for the client will not exceed jnxPPPoEIfLockoutMax. If the time between creation errors for the PPP interface for this interface is greater than the greater of 15 minutes and jnxPPPoEIfLockoutMax, then the lockout duration reverts to this object's value.
To disable the ability to lockout the client from recognition in the event of an error in creating a PPP interface for the specified interface, the value of this object and jnxPPPoEIfLockoutMin must be set to 0. It is not recommended that this lockout feature be disabled except for debugging purposes or when this interface supports more than one session.
What is jnxPPPoEIfLockoutMin?
This OID sets the starting duration, in seconds, that a misbehaving client is locked out from re-establishing a PPP interface on this PPPoE interface, and only applies when jnxPPPoEIfAutoconfig is enabled; setting both this and jnxPPPoEIfLockoutMax to zero disables lockout entirely. An engineer would only disable this lockout protection for debugging, since it normally guards against repeated failed dynamic interface creation.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.12 snmpwalk -v2c -c public <target> JNX-PPPOE-MIB::jnxPPPoEIfLockoutMin
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.12.1 snmpget -v2c -c public <target> JNX-PPPOE-MIB::jnxPPPoEIfLockoutMin.1
Start monitoring Juniper Networks MX-series broadband network gateway with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the JNX-PPPOE-MIB::jnxPPPoEIfLockoutMin OID value, configure state conditions and alerts, and monitor any Juniper Networks MX-series broadband network gateway from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.2636 | juniperMIB | JUNIPER-SMI |
| 1.3.6.1.4.1.2636.3 | jnxMibs | JUNIPER-SMI |
| 1.3.6.1.4.1.2636.3.67 | jnxPppoeMibRoot | JUNIPER-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.2636.3.67.1 | jnxPPPoEMIB | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1 | jnxPPPoEObjects | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.1 | jnxPPPoEIfLayer | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.1.2 | jnxPPPoEIfTable | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.1.2.1 | jnxPPPoEIfEntry | JNX-PPPOE-MIB |
| 1.3.6.1.4.1.2636.3.67.1.1.1.2.1.12 | jnxPPPoEIfLockoutMin | JNX-PPPOE-MIB |