All MIBs › HUAWEI-FLASH-MAN-MIB › hwFlhOperStatus
hwFlhOperStatus
Module: HUAWEI-FLASH-MAN-MIB
OID (symbolic): HUAWEI-FLASH-MAN-MIB::hwFlhOperStatus
OID (numeric): 1.3.6.1.4.1.2011.6.9.1.2.1.1.9
Node type: OBJECT-TYPE
Type: HwFlashOperationStatus
Access: read-only
Description: The status of operation. The status of the specified operation can be one of the follows.
opInProgress(1) : the operation is in process.
opSuccess(2) : the operation has been completed successfully.
opInvalid(3) : the command is invalid or command-protocol-device combination is unsupported by the system.
opInvalidProtocol(4) :invalid protocol is specified
opInvalidSourceName(5) :invalid source file name is specified.
opInvalidDestName(6) :invalid target name is specified.
opInvalidServerAddress(7) :invalid server address is specified
opDeviceBusy(8) :the device is in use and locked by another process
opDeviceOpenError(9) :invalid device name is specified.
opDeviceError(10) : device read, write or erase error
opDeviceNotProgrammable(11) :device is read-only but a write or erase operation was specified
opDeviceFull(12) : device is filled to capacity
opFileOpenError(13) :invalid file name; file not found in partition
opFileTransferError(14) :file transfer was unsuccessfull
opFileChecksumError(15) :file checksum in Flash si invalid
opNoMemory(16) :system is running in low on memory
opAuthFail(17) :authentication failure
opUnknownFailure(18) :failure which is unknown
opAbort(19) : transfer operation has been aborted
opInvalidSourceAddress(20) : invalid source IP is specified.
opInvalidSourceInterface(21) : invalid source interface is specified.
opCurrentVersionFileConfilt(22) : conflict between target file and system file
What is hwFlhOperStatus?
This reports the current outcome of a flash copy operation using a detailed enumeration — e.g. opInProgress(1) while the transfer is running, opSuccess(2) when it completes, or specific failure codes like opDeviceFull(12), opFileTransferError(14), or opAuthFail(17) — letting admins pinpoint exactly why a firmware or config transfer failed.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.2011.6.9.1.2.1.1.9 snmpwalk -v2c -c public <target> HUAWEI-FLASH-MAN-MIB::hwFlhOperStatus
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.2011.6.9.1.2.1.1.9.1 snmpget -v2c -c public <target> HUAWEI-FLASH-MAN-MIB::hwFlhOperStatus.1
Start monitoring Huawei router or switch (flash storage/software-image management) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the HUAWEI-FLASH-MAN-MIB::hwFlhOperStatus OID value, configure state conditions and alerts, and monitor any Huawei router or switch (flash storage/software-image management) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.2011 | huawei | HUAWEI-3COM-OID-MIB |
| 1.3.6.1.4.1.2011.6 | huaweiUtility | HUAWEI-3COM-OID-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.2011.6.9 | hwFlash | HUAWEI-FLASH-MAN-MIB |
| 1.3.6.1.4.1.2011.6.9.1 | huaweiFlashManMIBObjects | HUAWEI-FLASH-MAN-MIB |
| 1.3.6.1.4.1.2011.6.9.1.2 | huaweiFlashOperate | HUAWEI-FLASH-MAN-MIB |
| 1.3.6.1.4.1.2011.6.9.1.2.1 | huaweiFlhOpTable | HUAWEI-FLASH-MAN-MIB |
| 1.3.6.1.4.1.2011.6.9.1.2.1.1 | huaweiFlhOpEntry | HUAWEI-FLASH-MAN-MIB |
| 1.3.6.1.4.1.2011.6.9.1.2.1.1.9 | hwFlhOperStatus | HUAWEI-FLASH-MAN-MIB |