GSM7312-SWITCHING-MIB

All MIBs › GSM7312-SWITCHING-MIB

Organization: Netgear

Last Updated: 2003-05-06

Category: Technology: Switching/L2, Vendor: Netgear

Description: Netgear GSM7312 switch MIB for Layer 2 switching configuration including VLANs, spanning tree, and link aggregation.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GSM7312-SWITCHING-MIB?

GSM7312-SWITCHING-MIB is a Netgear vendor MIB for the GSM7312 managed Ethernet switch, covering Layer 2 switching features such as VLAN membership, spanning tree, and link aggregation configuration. Its conformance groups (agentSystemGroup, agentCableTesterGroup) show it exposes general system/agent status information plus a cable diagnostics capability in addition to switching configuration objects. It supports hardware status monitoring through its cable-tester feature, which identifies faulty copper cabling on a port, complementing system-level agent status reporting. It is intended to be used alongside standard Q-BRIDGE-MIB, BRIDGE-MIB, and IF-MIB for core VLAN, spanning tree, and interface counters. It is deployed on Netgear GSM7312 managed switches in enterprise network closets. Network engineers evaluating or troubleshooting this functionality can download the GSM7312-SWITCHING-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GSM7312-SWITCHING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Netgear GSM7312 managed Ethernet switch

Monitoring Examples

An administrator would run the cable-tester capability (agentCableTesterGroup) on a suspect port to detect an open or shorted copper pair causing link flaps. agentSystemGroup objects would be polled for overall switch/agent identity and status, such as firmware version, to confirm the device is healthy. Combined with standard Bridge-MIB VLAN and spanning-tree data, this MIB rounds out visibility into the GSM7312's Layer 2 configuration and cabling diagnostics.

What Can Be Monitored

cable diagnostics/cable tester results
system/agent status information
VLAN configuration
spanning tree and link aggregation status
port configuration

Imported Objects

From GSM7312-REF-MIB

AgentPortMask
gsm7312	MODULE-IDENTITY

From IANAifType-MIB

IANAifType

From IF-MIB

ifIndex

OBJECT-TYPE

From Q-BRIDGE-MIB

VlanIndex
dot1qFdbId	OBJECT-TYPE
dot1qVlanIndex	OBJECT-TYPE

From RFC1155-SMI

TimeTicks

From RFC1213-MIB

DisplayString
PhysAddress

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

MacAddress
RowStatus

How to Use in IPNetwork Monitor

Example using agentSwitchIGMPSnoopingMulticastControlFramesProcessed OID:

Select a Netgear GSM7312 managed Ethernet switch (L2 switching/cable diagnostics) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentSwitchIGMPSnoopingMulticastControlFramesProcessed into the Find box to locate it in the OID tree, then select it and click OK. It reports the multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
gsm7312Switching	1.3.6.1.4.1.4526.1.6.1
agentInfoGroup	1.3.6.1.4.1.4526.1.6.1.1
agentInventoryGroup	1.3.6.1.4.1.4526.1.6.1.1.1
STR agentInventorySysDescription	1.3.6.1.4.1.4526.1.6.1.1.1.1	DisplayString	read-only	The switch's Inventory system description.
STR agentInventoryMachineType	1.3.6.1.4.1.4526.1.6.1.1.1.2	DisplayString	read-only	Type of the Machine used in the Switch
PHY agentInventoryBurnedInMacAddress	1.3.6.1.4.1.4526.1.6.1.1.1.3	PhysAddress	read-only	Burned-In MAC Address
STR agentInventoryAdditionalPackages	1.3.6.1.4.1.4526.1.6.1.1.1.4	DisplayString	read-only	Lists additional functional packages available on this unit.
STR agentInventorySoftwareVersion	1.3.6.1.4.1.4526.1.6.1.1.1.5	DisplayString	read-only	Lists the version of software loaded on this unit.
agentTrapLogGroup	1.3.6.1.4.1.4526.1.6.1.1.2
I32 agentTrapLogTotal	1.3.6.1.4.1.4526.1.6.1.1.2.1	Integer32	read-only	The total number of traps sent since last reset.
I32 agentTrapLogTotalSinceLastViewed	1.3.6.1.4.1.4526.1.6.1.1.2.3	Integer32	read-only	The number of traps sent since last viewed.
agentTrapLogTable	1.3.6.1.4.1.4526.1.6.1.1.2.4		not-accessible	Agent Trap Log
agentTrapLogEntry	1.3.6.1.4.1.4526.1.6.1.1.2.4.1		not-accessible	Agent trap log entry
I32 agentTrapLogIndex	1.3.6.1.4.1.4526.1.6.1.1.2.4.1.1	Integer32	read-only	Unique index of trap entry
STR agentTrapLogSystemTime	1.3.6.1.4.1.4526.1.6.1.1.2.4.1.2	DisplayString	read-only	System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.
OCT agentTrapLogTrap	1.3.6.1.4.1.4526.1.6.1.1.2.4.1.3	OCTET STRING	read-only	Description of the trap sent.
agentSupportedMibTable	1.3.6.1.4.1.4526.1.6.1.1.3		not-accessible	Supported MIB table
agentSupportedMibEntry	1.3.6.1.4.1.4526.1.6.1.1.3.1		not-accessible	Supported MIB entry
I32 agentSupportedMibIndex	1.3.6.1.4.1.4526.1.6.1.1.3.1.1	Integer32	read-only	Unique index of the Supported MIB entry
STR agentSupportedMibName	1.3.6.1.4.1.4526.1.6.1.1.3.1.2	DisplayString	read-only	The name of the MIB (RFC or IEEE) that is supported.
OCT agentSupportedMibDescription	1.3.6.1.4.1.4526.1.6.1.1.3.1.3	OCTET STRING	read-only	Description of the MIB (RFC or IEEE) that is supported.
agentConfigGroup	1.3.6.1.4.1.4526.1.6.1.2
agentCLIConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.1
agentLoginSessionTable	1.3.6.1.4.1.4526.1.6.1.2.1.1		not-accessible	A table of the switch's login session
agentLoginSessionEntry	1.3.6.1.4.1.4526.1.6.1.2.1.1.1		not-accessible	Login Session Entry
I32 agentLoginSessionIndex	1.3.6.1.4.1.4526.1.6.1.2.1.1.1.1	Integer32	read-only	Agent Login Session Index of the switch
STR agentLoginSessionUserName	1.3.6.1.4.1.4526.1.6.1.2.1.1.1.2	DisplayString	read-only	Agent Login Session UserName of the switch
IP agentLoginSessionIPAddress	1.3.6.1.4.1.4526.1.6.1.2.1.1.1.3	IpAddress	read-only	Agent Login Session IP Address of the switch
INT agentLoginSessionConnectionType	1.3.6.1.4.1.4526.1.6.1.2.1.1.1.4	INTEGER	read-only	Agent Login Session Connection Type of the switch
TIK agentLoginSessionIdleTime	1.3.6.1.4.1.4526.1.6.1.2.1.1.1.5	TimeTicks	read-only	Agent Login Session Idle Time of the switch
TIK agentLoginSessionSessionTime	1.3.6.1.4.1.4526.1.6.1.2.1.1.1.6	TimeTicks	read-only	Agent Login Session Time of the switch
ROW agentLoginSessionStatus	1.3.6.1.4.1.4526.1.6.1.2.1.1.1.7	RowStatus	read-write	Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.
agentTelnetConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.1.2
I32 agentTelnetLoginTimeout	1.3.6.1.4.1.4526.1.6.1.2.1.2.1	Integer32	read-write	Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 0 to 160. A value of 0 indicates that a Telnet session remains active indefinitely. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.
I32 agentTelnetMaxSessions	1.3.6.1.4.1.4526.1.6.1.2.1.2.2	Integer32	read-write	Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.
INT agentTelnetAllowNewMode	1.3.6.1.4.1.4526.1.6.1.2.1.2.3	INTEGER	read-write	Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
agentUserConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.1.3
STR agentUserConfigCreate	1.3.6.1.4.1.4526.1.6.1.2.1.3.1	DisplayString	read-write	Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).
agentUserConfigTable	1.3.6.1.4.1.4526.1.6.1.2.1.3.2		not-accessible	User Config Table
agentUserConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1		not-accessible	User Config Entry
I32 agentUserIndex	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.1	Integer32	not-accessible	Agent User Config Index
STR agentUserName	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.2	DisplayString	read-write	Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).
STR agentUserPassword	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.3	DisplayString	read-write	Agent User Password This object will return an empty string even if a password is set.
INT agentUserAccessMode	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.4	INTEGER	read-only	Agent User Access Mode
ROW agentUserStatus	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.5	RowStatus	read-write	Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.
INT agentUserAuthenticationType	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.6	INTEGER	read-write	SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication
INT agentUserEncryptionType	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.7	INTEGER	read-write	SNMPv3 User Encryption Can not be set to des(2) if agentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used
STR agentUserEncryptionPassword	1.3.6.1.4.1.4526.1.6.1.2.1.3.2.1.8	DisplayString	read-write	SNMPv3 User Encryption Password This object will return an empty string even if a password is set. agentUserEncryptionType must be set to des(2) before this object can be configured. This object will return an empty string even if a password is set.
agentSerialGroup	1.3.6.1.4.1.4526.1.6.1.2.1.5
I32 agentSerialTimeout	1.3.6.1.4.1.4526.1.6.1.2.1.5.1	Integer32	read-write	agentSerialTimeout specifies the maximum connect time(in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time range is 0 to 160.
INT agentSerialBaudrate	1.3.6.1.4.1.4526.1.6.1.2.1.5.2	INTEGER	read-write	agentSerialBaudrate specifies the current baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud.
I32 agentSerialCharacterSize	1.3.6.1.4.1.4526.1.6.1.2.1.5.3	Integer32	read-only	agentSerialCharacterSize specifies the number of bits in a character. The number of bits is always 8.
INT agentSerialHWFlowControlMode	1.3.6.1.4.1.4526.1.6.1.2.1.5.4	INTEGER	read-only	agentSerialHardwareFlowControl specifies whether hardware flow-control is enabled or disabled. Hardware Flow Control is always disabled.
I32 agentSerialStopBits	1.3.6.1.4.1.4526.1.6.1.2.1.5.5	Integer32	read-only	agentSerialStopBits specifies the number of Stop bits per character. The number of Stop bits is always 1.
INT agentSerialParityType	1.3.6.1.4.1.4526.1.6.1.2.1.5.6	INTEGER	read-only	agentSerialParityType specifies the Parity Method used on the Serial Port. The Parity Method is always None.
agentLagConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.2
STR agentLagConfigCreate	1.3.6.1.4.1.4526.1.6.1.2.2.1	DisplayString	read-write	Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible with the entered string as its name.
agentLagSummaryConfigTable	1.3.6.1.4.1.4526.1.6.1.2.2.2		not-accessible	A summary table of the switch's LAG config entries
agentLagSummaryConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.2.2.1		not-accessible	Switch's LAG config entry
I32 agentLagSummaryLagIndex	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.1	Integer32	read-only	Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.
STR agentLagSummaryName	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.2	DisplayString	read-write	Agent LAG Name. The associated name of the LAG used during creation.
I32 agentLagSummaryFlushTimer	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.3	Integer32	read-write	Agent LAG FlushTimer.
INT agentLagSummaryLinkTrap	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.4	INTEGER	read-write	Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down.
INT agentLagSummaryAdminMode	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.5	INTEGER	read-write	Agent LAG AdminMode. Administratively enables or disables this LAG interface.
INT agentLagSummaryStpMode	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.6	INTEGER	read-write	Agent LAG StpMode If Dot1d is enabled, the valid values are: dot1d(1), fast(2), and off(3) If Dot1s is enabled, the valid values are: off(3) and dot1s(4)
I32 agentLagSummaryAddPort	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.7	Integer32	read-write	Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.
I32 agentLagSummaryDeletePort	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.8	Integer32	read-write	Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.
ROW agentLagSummaryStatus	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.9	RowStatus	read-write	Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.
INT agentLagSummaryType	1.3.6.1.4.1.4526.1.6.1.2.2.2.1.10	INTEGER	read-only	Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained.
agentLagDetailedConfigTable	1.3.6.1.4.1.4526.1.6.1.2.2.3		not-accessible	A detailed table of the switch's LAG config entries
agentLagDetailedConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.2.3.1		not-accessible	Switch's LAG config entry
I32 agentLagDetailedLagIndex	1.3.6.1.4.1.4526.1.6.1.2.2.3.1.1	Integer32	read-only	LAG index
I32 agentLagDetailedIfIndex	1.3.6.1.4.1.4526.1.6.1.2.2.3.1.2	Integer32	read-only	LAG port index
OID agentLagDetailedPortSpeed	1.3.6.1.4.1.4526.1.6.1.2.2.3.1.3	OBJECT IDENTIFIER	read-only	LAG port speed. See agentPortType for a description and list of valid values.
INT agentLagDetailedPortStatus	1.3.6.1.4.1.4526.1.6.1.2.2.3.1.4	INTEGER	read-only	LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.
INT agentLagConfigStaticCapability	1.3.6.1.4.1.4526.1.6.1.2.2.4	INTEGER	read-write	Agent LAG Static Capability. Configures whether Static LAGs are supported on this device.
agentNetworkConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.3
IP agentNetworkIPAddress	1.3.6.1.4.1.4526.1.6.1.2.3.1	IpAddress	read-write	The switch's network ip address
IP agentNetworkSubnetMask	1.3.6.1.4.1.4526.1.6.1.2.3.2	IpAddress	read-write	The switch's network subnet mask
IP agentNetworkDefaultGateway	1.3.6.1.4.1.4526.1.6.1.2.3.3	IpAddress	read-write	The switch's network default gateway
PHY agentNetworkBurnedInMacAddress	1.3.6.1.4.1.4526.1.6.1.2.3.4	PhysAddress	read-only	The switch's network Burned-In MAC address
INT agentNetworkConfigProtocol	1.3.6.1.4.1.4526.1.6.1.2.3.5	INTEGER	read-write	The switch's network config protocol
INT agentNetworkWebMode	1.3.6.1.4.1.4526.1.6.1.2.3.6	INTEGER	read-write	The switch's network config protocol on next bootup
INT agentNetworkJavaMode	1.3.6.1.4.1.4526.1.6.1.2.3.7	INTEGER	read-write	Configures the use of the Java interface through the Web.
I32 agentNetworkMgmtVlan	1.3.6.1.4.1.4526.1.6.1.2.3.8	Integer32	read-write	The VLAN ID through which the switch can be managed using the agentNetworkIPAddress
agentServicePortConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.4
IP agentServicePortIPAddress	1.3.6.1.4.1.4526.1.6.1.2.4.1	IpAddress	read-write	The switch's ServicePort ip address
IP agentServicePortSubnetMask	1.3.6.1.4.1.4526.1.6.1.2.4.2	IpAddress	read-write	The switch's ServicePort subnet mask
IP agentServicePortDefaultGateway	1.3.6.1.4.1.4526.1.6.1.2.4.3	IpAddress	read-write	The switch's ServicePort default gateway
PHY agentServicePortBurnedInMacAddress	1.3.6.1.4.1.4526.1.6.1.2.4.4	PhysAddress	read-only	The switch's ServicePort Burned-In MAC address
INT agentServicePortConfigProtocol	1.3.6.1.4.1.4526.1.6.1.2.4.5	INTEGER	read-write	The switch's ServicePort config protocol
agentSnmpConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.6
STR agentSnmpCommunityCreate	1.3.6.1.4.1.4526.1.6.1.2.6.1	DisplayString	read-write	Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config
agentSnmpCommunityConfigTable	1.3.6.1.4.1.4526.1.6.1.2.6.2		not-accessible	A table of the switch's SNMP Config entries
agentSnmpCommunityConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.6.2.1		not-accessible	Switch's SNMP Config entry
I32 agentSnmpCommunityIndex	1.3.6.1.4.1.4526.1.6.1.2.6.2.1.1	Integer32	read-only	The switch's Snmp Community Index
STR agentSnmpCommunityName	1.3.6.1.4.1.4526.1.6.1.2.6.2.1.2	DisplayString	read-write	The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.
IP agentSnmpCommunityIPAddress	1.3.6.1.4.1.4526.1.6.1.2.6.2.1.3	IpAddress	read-write	The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.
IP agentSnmpCommunityIPMask	1.3.6.1.4.1.4526.1.6.1.2.6.2.1.4	IpAddress	read-write	The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.
INT agentSnmpCommunityAccessMode	1.3.6.1.4.1.4526.1.6.1.2.6.2.1.5	INTEGER	read-write	The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch information to be displayed. A community with a read/write access allows for configuration changes to be made and for information to be displayed.
INT agentSnmpCommunityStatus	1.3.6.1.4.1.4526.1.6.1.2.6.2.1.6	INTEGER	read-write	The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.
STR agentSnmpTrapReceiverCreate	1.3.6.1.4.1.4526.1.6.1.2.6.3	DisplayString	read-write	Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config
agentSnmpTrapReceiverConfigTable	1.3.6.1.4.1.4526.1.6.1.2.6.4		not-accessible	Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.
agentSnmpTrapReceiverConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.6.4.1		not-accessible	Switch's Snmp Trace Receiver Config entry
I32 agentSnmpTrapReceiverIndex	1.3.6.1.4.1.4526.1.6.1.2.6.4.1.1	Integer32	read-only	The switch's Snmp Trap Receiver Index
STR agentSnmpTrapReceiverCommunityName	1.3.6.1.4.1.4526.1.6.1.2.6.4.1.2	DisplayString	read-write	The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive.
IP agentSnmpTrapReceiverIPAddress	1.3.6.1.4.1.4526.1.6.1.2.6.4.1.3	IpAddress	read-write	IP Address - Each IP address parameter is four integer numbers. The numbers range from 0 to 255.
INT agentSnmpTrapReceiverStatus	1.3.6.1.4.1.4526.1.6.1.2.6.4.1.4	INTEGER	read-write	The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap reciever is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap reciever Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: agentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap receiver entry from the agent.
agentSnmpTrapFlagsConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.6.5
INT agentSnmpAuthenticationTrapFlag	1.3.6.1.4.1.4526.1.6.1.2.6.5.1	INTEGER	read-write	Authentication Flag - Enable/Disable authentication Flag.
INT agentSnmpLinkUpDownTrapFlag	1.3.6.1.4.1.4526.1.6.1.2.6.5.2	INTEGER	read-write	Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.
INT agentSnmpMultipleUsersTrapFlag	1.3.6.1.4.1.4526.1.6.1.2.6.5.3	INTEGER	read-write	Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session.
INT agentSnmpSpanningTreeTrapFlag	1.3.6.1.4.1.4526.1.6.1.2.6.5.4	INTEGER	read-write	Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.
INT agentSnmpBroadcastStormTrapFlag	1.3.6.1.4.1.4526.1.6.1.2.6.5.5	INTEGER	read-write	Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.
agentSpanningTreeConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.7
INT agentSpanningTreeMode	1.3.6.1.4.1.4526.1.6.1.2.7.1	INTEGER	read-write	The switch's Spanning Tree Switch Status
agentSwitchConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.8
INT agentSwitchBroadcastControlMode	1.3.6.1.4.1.4526.1.6.1.2.8.2	INTEGER	read-write	The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discards) the broadcast traffic until the broadcast traffic returns to 10 percent or less. Upper limit for 10M link is 20% and lower limit is 10%. For 100M link Upper limit is 5% and lower limit is 2%
INT agentSwitchDot3FlowControlMode	1.3.6.1.4.1.4526.1.6.1.2.8.3	INTEGER	read-write	Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.
agentSwitchAddressAgingTimeoutTable	1.3.6.1.4.1.4526.1.6.1.2.8.4		not-accessible	The switch's address aging timeout table
agentSwitchAddressAgingTimeoutEntry	1.3.6.1.4.1.4526.1.6.1.2.8.4.1		not-accessible	Aging information about a specific Filtering Database.
I32 agentSwitchAddressAgingTimeout	1.3.6.1.4.1.4526.1.6.1.2.8.4.1.1	Integer32	read-write	The FDB entry's address aging timeout (in seconds)
agentSwitchIGMPSnoopingGroup	1.3.6.1.4.1.4526.1.6.1.2.8.6
INT agentSwitchIGMPSnoopingAdminMode	1.3.6.1.4.1.4526.1.6.1.2.8.6.1	INTEGER	read-write	This enables or disables IGMP Snooping on the system.
I32 agentSwitchIGMPSnoopingGroupMembershipInterval	1.3.6.1.4.1.4526.1.6.1.2.8.6.2	Integer32	read-write	The amount of time in seconds a switch will wait for a report for a particular group on a particular interface before it deletes the interface from the entry.
I32 agentSwitchIGMPSnoopingMaxResponseTime	1.3.6.1.4.1.4526.1.6.1.2.8.6.3	Integer32	read-write	The amount of time in seconds a switch will wait after sending a query on an interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchIGMPSnoopingQueryInterval.
I32 agentSwitchIGMPSnoopingMRPExpirationTime	1.3.6.1.4.1.4526.1.6.1.2.8.6.4	Integer32	read-write	Multicast Router Present Expiration Time. The amount of time in seconds a switch will wait for a query to be received on an interface before the interface is removed from the list of interfaces with mutlticast routers attached. A value of zero indicates an infinite timeout, i.e. the entries in the list will not expire.
AGE agentSwitchIGMPSnoopingPortMask	1.3.6.1.4.1.4526.1.6.1.2.8.6.5	AgentPortMask	read-write	IGMP Snooping Port Mask. This allows configuration of IGMP Snooping on selected ports. IGMP Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP Snooping functionality will be disabled on that port. IGMP Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP Snooping enabled. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
C32 agentSwitchIGMPSnoopingMulticastControlFramesProcessedEx	1.3.6.1.4.1.4526.1.6.1.2.8.6.6	Counter32	read-only	Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.
agentSwitchMFDBGroup	1.3.6.1.4.1.4526.1.6.1.2.8.7
agentSwitchMFDBTable	1.3.6.1.4.1.4526.1.6.1.2.8.7.1		not-accessible	The Multicast Forwarding Database table
agentSwitchMFDBEntry	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1		not-accessible	Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User.
VLA agentSwitchMFDBVlanId	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1.1	VlanIndex	read-only	Vlan Index for which this entry is associated with.
MAC agentSwitchMFDBMacAddress	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1.2	MacAddress	read-only	A multicast MAC address for which the switch has forwarding and or filtering information.
INT agentSwitchMFDBProtocolType	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1.3	INTEGER	read-only	The component that is responsible for this entry in the Multicast Forwarding Database.
INT agentSwitchMFDBType	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1.4	INTEGER	read-only	This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol
STR agentSwitchMFDBDescription	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1.5	DisplayString	read-only	Text description of this multicast table entry.
AGE agentSwitchMFDBForwardingPortMask	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1.6	AgentPortMask	read-only	BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
AGE agentSwitchMFDBFilteringPortMask	1.3.6.1.4.1.4526.1.6.1.2.8.7.1.1.7	AgentPortMask	read-only	BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
agentSwitchMFDBSummaryTable	1.3.6.1.4.1.4526.1.6.1.2.8.7.2		not-accessible	The Multicast Forwarding Database Summary table
agentSwitchMFDBSummaryEntry	1.3.6.1.4.1.4526.1.6.1.2.8.7.2.1		not-accessible	Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address.
VLA agentSwitchMFDBSummaryVlanId	1.3.6.1.4.1.4526.1.6.1.2.8.7.2.1.1	VlanIndex	read-only	Vlan Index for which this entry is associated with.
MAC agentSwitchMFDBSummaryMacAddress	1.3.6.1.4.1.4526.1.6.1.2.8.7.2.1.2	MacAddress	read-only	A multicast MAC address for which the switch has forwarding and or filtering information.
AGE agentSwitchMFDBSummaryForwardingPortMask	1.3.6.1.4.1.4526.1.6.1.2.8.7.2.1.3	AgentPortMask	read-only	Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
G32 agentSwitchMFDBMaxTableEntries	1.3.6.1.4.1.4526.1.6.1.2.8.7.3	Gauge32	read-only	This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table.
G32 agentSwitchMFDBMostEntriesUsed	1.3.6.1.4.1.4526.1.6.1.2.8.7.4	Gauge32	read-only	This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark.
G32 agentSwitchMFDBCurrentEntries	1.3.6.1.4.1.4526.1.6.1.2.8.7.5	Gauge32	read-only	This displays the current number of entries in the Multicast Forwarding Database table.
agentTransferConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.9
agentTransferUploadGroup	1.3.6.1.4.1.4526.1.6.1.2.9.1
INT agentTransferUploadMode	1.3.6.1.4.1.4526.1.6.1.2.9.1.1	INTEGER	read-write	Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
IP agentTransferUploadServerIP	1.3.6.1.4.1.4526.1.6.1.2.9.1.2	IpAddress	read-write	Transfer upload tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
STR agentTransferUploadPath	1.3.6.1.4.1.4526.1.6.1.2.9.1.3	DisplayString	read-write	Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.
STR agentTransferUploadFilename	1.3.6.1.4.1.4526.1.6.1.2.9.1.4	DisplayString	read-write	Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
INT agentTransferUploadDataType	1.3.6.1.4.1.4526.1.6.1.2.9.1.5	INTEGER	read-write	Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - Message log - Trap log
INT agentTransferUploadStart	1.3.6.1.4.1.4526.1.6.1.2.9.1.6	INTEGER	read-write	Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
INT agentTransferUploadStatus	1.3.6.1.4.1.4526.1.6.1.2.9.1.7	INTEGER	read-only	Indicates the current status of an upload transfer.
agentTransferDownloadGroup	1.3.6.1.4.1.4526.1.6.1.2.9.2
INT agentTransferDownloadMode	1.3.6.1.4.1.4526.1.6.1.2.9.2.1	INTEGER	read-write	Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
IP agentTransferDownloadServerIP	1.3.6.1.4.1.4526.1.6.1.2.9.2.2	IpAddress	read-write	Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
STR agentTransferDownloadPath	1.3.6.1.4.1.4526.1.6.1.2.9.2.3	DisplayString	read-write	Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.
STR agentTransferDownloadFilename	1.3.6.1.4.1.4526.1.6.1.2.9.2.4	DisplayString	read-write	Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
INT agentTransferDownloadDataType	1.3.6.1.4.1.4526.1.6.1.2.9.2.5	INTEGER	read-write	Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File sshkey-rsa1 - SSH-1 RSA Key File sshkey-rsa2 - SSH-2 RSA Key PEM File sshkey-dsa - SSH-2 DSA Key PEM File sslpem-root - SSL Trusted Root Certificate PEM File sslpem-server - SSL Server Certificate PEM File sslpem-dhweak - SSL DH Weak Encryption Parameter PEM File sslpem-dhstrong - SSL DH Strong Encryption Parameter PEM File Note: SSH Key files can only be downloaded if SSH Server is administratively disabled, and there are no active SSH sessions.
INT agentTransferDownloadStart	1.3.6.1.4.1.4526.1.6.1.2.9.2.6	INTEGER	read-write	Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
INT agentTransferDownloadStatus	1.3.6.1.4.1.4526.1.6.1.2.9.2.7	INTEGER	read-only	Indicates the current status of an download transfer.
agentPortMirroringGroup	1.3.6.1.4.1.4526.1.6.1.2.10
I32 agentMirroredPortIfIndex	1.3.6.1.4.1.4526.1.6.1.2.10.1	Integer32	read-write	IfIndex of the mirrored port
I32 agentProbePortIfIndex	1.3.6.1.4.1.4526.1.6.1.2.10.2	Integer32	read-write	IfIndex of the probe port
INT agentPortMirroringMode	1.3.6.1.4.1.4526.1.6.1.2.10.3	INTEGER	read-write	Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration
agentDot3adAggPortTable	1.3.6.1.4.1.4526.1.6.1.2.12		not-accessible	This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.
agentDot3adAggPortEntry	1.3.6.1.4.1.4526.1.6.1.2.12.1		not-accessible	Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.
I32 agentDot3adAggPort	1.3.6.1.4.1.4526.1.6.1.2.12.1.1	Integer32	read-only	ifIndex of this physical port
INT agentDot3adAggPortLACPMode	1.3.6.1.4.1.4526.1.6.1.2.12.1.2	INTEGER	read-write	Enable/disable 802.3ad LACP on this port
agentPortConfigTable	1.3.6.1.4.1.4526.1.6.1.2.13		not-accessible	A table of the switch's physical port config entries
agentPortConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.13.1		not-accessible	Switch's physical port config entry
I32 agentPortDot1dBasePort	1.3.6.1.4.1.4526.1.6.1.2.13.1.1	Integer32	read-only	The port number of this port.
I32 agentPortIfIndex	1.3.6.1.4.1.4526.1.6.1.2.13.1.2	Integer32	read-only	The switch's Port IfIndex
IAN agentPortIanaType	1.3.6.1.4.1.4526.1.6.1.2.13.1.3	IANAifType	read-only	The switch's Port Type
INT agentPortSTPMode	1.3.6.1.4.1.4526.1.6.1.2.13.1.4	INTEGER	read-write	The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled.
INT agentPortSTPState	1.3.6.1.4.1.4526.1.6.1.2.13.1.5	INTEGER	read-only	The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled.
INT agentPortAdminMode	1.3.6.1.4.1.4526.1.6.1.2.13.1.6	INTEGER	read-write	The switch's Port Admin Mode
INT agentPortPhysicalMode	1.3.6.1.4.1.4526.1.6.1.2.13.1.7	INTEGER	read-write	The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports
INT agentPortPhysicalStatus	1.3.6.1.4.1.4526.1.6.1.2.13.1.8	INTEGER	read-only	The switch's Port Physical Speed Status. This is the current actual speed.
INT agentPortLinkTrapMode	1.3.6.1.4.1.4526.1.6.1.2.13.1.9	INTEGER	read-write	If enabled, link up and link down traps will be sent for this port.
INT agentPortClearStats	1.3.6.1.4.1.4526.1.6.1.2.13.1.10	INTEGER	read-write	clear stats for this port only
OID agentPortDefaultType	1.3.6.1.4.1.4526.1.6.1.2.13.1.11	OBJECT IDENTIFIER	read-write	This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
OID agentPortType	1.3.6.1.4.1.4526.1.6.1.2.13.1.12	OBJECT IDENTIFIER	read-only	This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object agentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object agentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType1000BaseTFD
INT agentPortAutoNegAdminStatus	1.3.6.1.4.1.4526.1.6.1.2.13.1.13	INTEGER	read-write	This object identifies the administration status of auto negotiation for this port.
INT agentPortDot3FlowControlMode	1.3.6.1.4.1.4526.1.6.1.2.13.1.14	INTEGER	read-write	Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.
INT agentPortDVlanTagMode	1.3.6.1.4.1.4526.1.6.1.2.13.1.15	INTEGER	read-write	Controls the Double Vlan Tag mode on this port.
I32 agentPortDVlanTagEthertype	1.3.6.1.4.1.4526.1.6.1.2.13.1.16	Integer32	read-write	Configures the Ethertype for the Double Vlan Tag for this port. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).
I32 agentPortDVlanTagCustomerId	1.3.6.1.4.1.4526.1.6.1.2.13.1.17	Integer32	read-write	Configures the Customer ID for the Double Vlan Tag for this port.
I32 agentPortMaxFrameSizeLimit	1.3.6.1.4.1.4526.1.6.1.2.13.1.18	Integer32	read-only	This object identifies the largest value that can be configured for agentPortMaxFrameSize
I32 agentPortMaxFrameSize	1.3.6.1.4.1.4526.1.6.1.2.13.1.19	Integer32	read-write	This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of agentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1522
agentProtocolConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.14
STR agentProtocolGroupCreate	1.3.6.1.4.1.4526.1.6.1.2.14.1	DisplayString	read-write	Set to non-empty string to create a Protocol-Based VLAN group.
agentProtocolGroupTable	1.3.6.1.4.1.4526.1.6.1.2.14.2		not-accessible	A table of the switch's Protocol-based VLAN entries
agentProtocolGroupEntry	1.3.6.1.4.1.4526.1.6.1.2.14.2.1		not-accessible	Switch's Protocol-based VLAN entry
I32 agentProtocolGroupId	1.3.6.1.4.1.4526.1.6.1.2.14.2.1.1	Integer32	read-only	Group identifier of the Protocol-based VLAN entry.
STR agentProtocolGroupName	1.3.6.1.4.1.4526.1.6.1.2.14.2.1.2	DisplayString	read-only	Group name of the Protocol-based VLAN entry.
I32 agentProtocolGroupVlanId	1.3.6.1.4.1.4526.1.6.1.2.14.2.1.3	Integer32	read-write	VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.
INT agentProtocolGroupProtocolIP	1.3.6.1.4.1.4526.1.6.1.2.14.2.1.4	INTEGER	read-write	The status of the IP protocol association with the Protocol-based VLAN entry.
INT agentProtocolGroupProtocolARP	1.3.6.1.4.1.4526.1.6.1.2.14.2.1.5	INTEGER	read-write	The status of the ARP protocol association with the Protocol-based VLAN entry.
INT agentProtocolGroupProtocolIPX	1.3.6.1.4.1.4526.1.6.1.2.14.2.1.6	INTEGER	read-write	The status of the IPX protocol association with the Protocol-based VLAN entry.
ROW agentProtocolGroupStatus	1.3.6.1.4.1.4526.1.6.1.2.14.2.1.7	RowStatus	read-write	The status of the Protocol-based VLAN entry. active(1) - this entry is active destroy(6) - remove this entry
agentProtocolGroupPortTable	1.3.6.1.4.1.4526.1.6.1.2.14.3		not-accessible	A table of the switch's physical port config entries
agentProtocolGroupPortEntry	1.3.6.1.4.1.4526.1.6.1.2.14.3.1		not-accessible	Switch's physical port config entry
I32 agentProtocolGroupPortIfIndex	1.3.6.1.4.1.4526.1.6.1.2.14.3.1.1	Integer32	read-only	The interface number of this instance.
ROW agentProtocolGroupPortStatus	1.3.6.1.4.1.4526.1.6.1.2.14.3.1.2	RowStatus	read-create	The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group
agentStpSwitchConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.15
OCT agentStpConfigDigestKey	1.3.6.1.4.1.4526.1.6.1.2.15.1	OCTET STRING	read-only	The MST configuration digest key.
U32 agentStpConfigFormatSelector	1.3.6.1.4.1.4526.1.6.1.2.15.2	Unsigned32	read-only	The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard.
STR agentStpConfigName	1.3.6.1.4.1.4526.1.6.1.2.15.3	DisplayString	read-write	The MST configuration name of at most 32 characters.
U32 agentStpConfigRevision	1.3.6.1.4.1.4526.1.6.1.2.15.4	Unsigned32	read-write	The MST configuration revision. The default value is 1.
INT agentStpForceVersion	1.3.6.1.4.1.4526.1.6.1.2.15.5	INTEGER	read-write	The MST configuration force protocol version. The default version is dot1s.
INT agentStpAdminMode	1.3.6.1.4.1.4526.1.6.1.2.15.6	INTEGER	read-write	The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is disabled.
agentStpPortTable	1.3.6.1.4.1.4526.1.6.1.2.15.7		not-accessible	STP port table.
agentStpPortEntry	1.3.6.1.4.1.4526.1.6.1.2.15.7.1		not-accessible	STP port entry.
INT agentStpPortState	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.1	INTEGER	read-write	The administrative bridge port state. enable(1) - enables the port. disable(2) - disables the port. The default port state is enabled for the first 4095 ports and disabled for any ports beyond.
C32 agentStpPortStatsMstpBpduRx	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.2	Counter32	read-only	The MSTP BPDUs received on a specific port.
C32 agentStpPortStatsMstpBpduTx	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.3	Counter32	read-only	The MSTP BPDUs sent from a specific port.
C32 agentStpPortStatsRstpBpduRx	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.4	Counter32	read-only	The RSTP BPDUs received on a specific port.
C32 agentStpPortStatsRstpBpduTx	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.5	Counter32	read-only	The RSTP BPDUs sent from a specific port.
C32 agentStpPortStatsStpBpduRx	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.6	Counter32	read-only	The STP BPDUs received on a specific port.
C32 agentStpPortStatsStpBpduTx	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.7	Counter32	read-only	The STP BPDUs sent from a specific port.
TIK agentStpPortUpTime	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.8	TimeTicks	read-only	Time since port was reset. It is displayed in days, hours, minutes, and seconds.
INT agentStpPortMigrationCheck	1.3.6.1.4.1.4526.1.6.1.2.15.7.1.9	INTEGER	read-write	Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port.
agentStpCstConfigGroup	1.3.6.1.4.1.4526.1.6.1.2.15.8
U32 agentStpCstHelloTime	1.3.6.1.4.1.4526.1.6.1.2.15.8.1	Unsigned32	read-only	The MSTP root port hello time for the CIST.
U32 agentStpCstMaxAge	1.3.6.1.4.1.4526.1.6.1.2.15.8.2	Unsigned32	read-only	The MSTP root port max age for the CIST.
OCT agentStpCstRegionalRootId	1.3.6.1.4.1.4526.1.6.1.2.15.8.3	OCTET STRING	read-only	The MSTP regional root identifier for the CIST.
U32 agentStpCstRegionalRootPathCost	1.3.6.1.4.1.4526.1.6.1.2.15.8.4	Unsigned32	read-only	The MSTP regional root path cost for the CIST.
U32 agentStpCstRootFwdDelay	1.3.6.1.4.1.4526.1.6.1.2.15.8.5	Unsigned32	read-only	The MSTP root port forward delay for the CIST.
U32 agentStpCstBridgeFwdDelay	1.3.6.1.4.1.4526.1.6.1.2.15.8.6	Unsigned32	read-write	The MSTP bridge forward delay for the CIST. The default value is 15.
U32 agentStpCstBridgeHelloTime	1.3.6.1.4.1.4526.1.6.1.2.15.8.7	Unsigned32	read-write	The MSTP bridge hello time for the CIST. The default value is 2.
U32 agentStpCstBridgeHoldTime	1.3.6.1.4.1.4526.1.6.1.2.15.8.8	Unsigned32	read-only	The MSTP bridge hold time for the CIST.
U32 agentStpCstBridgeMaxAge	1.3.6.1.4.1.4526.1.6.1.2.15.8.9	Unsigned32	read-write	The MSTP bridge max age for the CIST. The default value is 20.
agentStpCstPortTable	1.3.6.1.4.1.4526.1.6.1.2.15.9		not-accessible	CIST port table.
agentStpCstPortEntry	1.3.6.1.4.1.4526.1.6.1.2.15.9.1		not-accessible	CIST port entry.
INT agentStpCstPortOperEdge	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.1	INTEGER	read-only	The MSTP operational status of a specific port for the CIST.
INT agentStpCstPortOperPointToPoint	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.2	INTEGER	read-only	The MSTP operational point to point mac of a specific port for the CIST.
INT agentStpCstPortTopologyChangeAck	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.3	INTEGER	read-only	The MSTP topology change acknowledge for a specific port in the CIST.
INT agentStpCstPortEdge	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.4	INTEGER	read-write	The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled.
INT agentStpCstPortForwardingState	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.5	INTEGER	read-only	The MSTP forwarding state of a specific port in CIST.
OCT agentStpCstPortId	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.6	OCTET STRING	read-only	The MSTP port identifier of a specific port in CIST.
U32 agentStpCstPortPathCost	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.7	Unsigned32	read-write	The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
U32 agentStpCstPortPriority	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.8	Unsigned32	read-write	The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128.
OCT agentStpCstDesignatedBridgeId	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.9	OCTET STRING	read-only	The MSTP designated bridge ID of a specific port in CIST.
U32 agentStpCstDesignatedCost	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.10	Unsigned32	read-only	The MSTP designated cost of a specific port in CIST.
OCT agentStpCstDesignatedPortId	1.3.6.1.4.1.4526.1.6.1.2.15.9.1.11	OCTET STRING	read-only	The MSTP designated port ID of a specific port in CIST.
agentStpMstTable	1.3.6.1.4.1.4526.1.6.1.2.15.10		not-accessible	MST table.
agentStpMstEntry	1.3.6.1.4.1.4526.1.6.1.2.15.10.1		not-accessible	MST entry.
U32 agentStpMstId	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.1	Unsigned32	read-only	The MSTP instance ID.
U32 agentStpMstBridgePriority	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.2	Unsigned32	read-write	The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.
OCT agentStpMstBridgeIdentifier	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.3	OCTET STRING	read-only	The MSTP bridge identifier in a specific instance.
OCT agentStpMstDesignatedRootId	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.4	OCTET STRING	read-only	The MSTP designated root bridge identifier in a specific instance.
U32 agentStpMstRootPathCost	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.5	Unsigned32	read-only	The MSTP root path cost in a specific instance.
OCT agentStpMstRootPortId	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.6	OCTET STRING	read-only	The MSTP root port ID in a specific instance.
TIK agentStpMstTimeSinceTopologyChange	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.7	TimeTicks	read-only	The MSTP time since the last topology change in a specific instance.
C32 agentStpMstTopologyChangeCount	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.8	Counter32	read-only	The MSTP count of topology changes in a specific instance.
INT agentStpMstTopologyChangeParm	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.9	INTEGER	read-only	The MSTP topology change parameter in a specific instance.
ROW agentStpMstRowStatus	1.3.6.1.4.1.4526.1.6.1.2.15.10.1.10	RowStatus	read-create	The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.
agentStpMstPortTable	1.3.6.1.4.1.4526.1.6.1.2.15.11		not-accessible	MST port table.
agentStpMstPortEntry	1.3.6.1.4.1.4526.1.6.1.2.15.11.1		not-accessible	MST port entry.
INT agentStpMstPortForwardingState	1.3.6.1.4.1.4526.1.6.1.2.15.11.1.1	INTEGER	read-only	The MSTP forwarding state of a specific port in a specific instance.
OCT agentStpMstPortId	1.3.6.1.4.1.4526.1.6.1.2.15.11.1.2	OCTET STRING	read-only	The MSTP port identifier of a specific port in a specific instance.
U32 agentStpMstPortPathCost	1.3.6.1.4.1.4526.1.6.1.2.15.11.1.3	Unsigned32	read-write	The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
U32 agentStpMstPortPriority	1.3.6.1.4.1.4526.1.6.1.2.15.11.1.4	Unsigned32	read-write	The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128.
OCT agentStpMstDesignatedBridgeId	1.3.6.1.4.1.4526.1.6.1.2.15.11.1.5	OCTET STRING	read-only	The MSTP designated bridge ID of a specific port in a specific instance.
U32 agentStpMstDesignatedCost	1.3.6.1.4.1.4526.1.6.1.2.15.11.1.6	Unsigned32	read-only	The MSTP designated cost of a specific port in a specific instance.
OCT agentStpMstDesignatedPortId	1.3.6.1.4.1.4526.1.6.1.2.15.11.1.7	OCTET STRING	read-only	The MSTP designated port ID of a specific port in a specific instance.
agentStpMstVlanTable	1.3.6.1.4.1.4526.1.6.1.2.15.12		not-accessible	MST VLAN table.
agentStpMstVlanEntry	1.3.6.1.4.1.4526.1.6.1.2.15.12.1		not-accessible	MST VLAN entry.
ROW agentStpMstVlanRowStatus	1.3.6.1.4.1.4526.1.6.1.2.15.12.1.1	RowStatus	read-create	The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.
agentAuthenticationGroup	1.3.6.1.4.1.4526.1.6.1.2.16
STR agentAuthenticationListCreate	1.3.6.1.4.1.4526.1.6.1.2.16.1	DisplayString	read-write	Authentication List Create If set to a non empty string, creates a new Authentication List for configuration.
agentAuthenticationListTable	1.3.6.1.4.1.4526.1.6.1.2.16.2		not-accessible	MST VLAN table.
agentAuthenticationListEntry	1.3.6.1.4.1.4526.1.6.1.2.16.2.1		not-accessible	MST VLAN entry.
U32 agentAuthenticationListIndex	1.3.6.1.4.1.4526.1.6.1.2.16.2.1.1	Unsigned32	not-accessible	Authenticaiton List Index Unique number used for indexing into this table.
STR agentAuthenticationListName	1.3.6.1.4.1.4526.1.6.1.2.16.2.1.2	DisplayString	read-only	Authenticaiton List Name Unique name used to identify the Authentication List from other tables.
INT agentAuthenticationListMethod1	1.3.6.1.4.1.4526.1.6.1.2.16.2.1.3	INTEGER	read-write	Authenticion List Method 1 Configures the first authentication method to use when this list is specified.
INT agentAuthenticationListMethod2	1.3.6.1.4.1.4526.1.6.1.2.16.2.1.4	INTEGER	read-write	Authenticion List Method 2 Configures the second authentication method to use when this list is specified.
INT agentAuthenticationListMethod3	1.3.6.1.4.1.4526.1.6.1.2.16.2.1.5	INTEGER	read-write	Authenticion List Method 3 Configures the third authentication method to use when this list is specified.
ROW agentAuthenticationListStatus	1.3.6.1.4.1.4526.1.6.1.2.16.2.1.6	RowStatus	read-write	The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List destroy(6) - removes the Authentication List.
STR agentUserConfigDefaultAuthenticationList	1.3.6.1.4.1.4526.1.6.1.2.16.3	DisplayString	read-write	Default Authentication List This object configures which authentication list to use for users which do not have an Authentication List configured. The list must be configured before setting.
agentUserAuthenticationConfigTable	1.3.6.1.4.1.4526.1.6.1.2.16.4		not-accessible	User Authentication Config Table
agentUserAuthenticationConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.16.4.1		not-accessible	User Authentication Config Entry
STR agentUserAuthenticationList	1.3.6.1.4.1.4526.1.6.1.2.16.4.1.1	DisplayString	read-write	User Authentication List This object configures which authentication list to use for this user. The list must be configured before setting.
agentUserPortConfigTable	1.3.6.1.4.1.4526.1.6.1.2.16.5		not-accessible	User Port Config Table
agentUserPortConfigEntry	1.3.6.1.4.1.4526.1.6.1.2.16.5.1		not-accessible	User Port Config Entry
AGE agentUserPortSecurity	1.3.6.1.4.1.4526.1.6.1.2.16.5.1.1	AgentPortMask	read-write	User Port Port Security This object configures which ports the user has access to. Ports are indexed based on dot1dBasePort entries in dot1dBasePortTable.
agentClassOfServiceGroup	1.3.6.1.4.1.4526.1.6.1.2.17
agentClassOfServiceTable	1.3.6.1.4.1.4526.1.6.1.2.17.1		not-accessible	A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port.
agentClassOfServiceEntry	1.3.6.1.4.1.4526.1.6.1.2.17.1.1		not-accessible	A 802.1p priority mapped to a traffic class priority queue.
I32 agentClassOfServicePriority	1.3.6.1.4.1.4526.1.6.1.2.17.1.1.1	Integer32	not-accessible	The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port.
I32 agentClassOfServiceClass	1.3.6.1.4.1.4526.1.6.1.2.17.1.1.2	Integer32	read-write	Traffic class priority queue the received frame is mapped to.
agentSystemGroup	1.3.6.1.4.1.4526.1.6.1.3
INT agentSaveConfig	1.3.6.1.4.1.4526.1.6.1.3.1	INTEGER	read-write	Enable agentSaveConfig will initiate an configuration save to nvram. Disable agentSaveConfig after a configuration save will reset agentSaveConfigStatus back to notInitiated state.
INT agentClearConfig	1.3.6.1.4.1.4526.1.6.1.3.2	INTEGER	read-write	clear config to factory defaults
INT agentClearLags	1.3.6.1.4.1.4526.1.6.1.3.3	INTEGER	read-write	clear lag configuration
INT agentClearLoginSessions	1.3.6.1.4.1.4526.1.6.1.3.4	INTEGER	read-write	close all telnet sessions
INT agentClearPasswords	1.3.6.1.4.1.4526.1.6.1.3.5	INTEGER	read-write	reset passwords
INT agentClearPortStats	1.3.6.1.4.1.4526.1.6.1.3.6	INTEGER	read-write	clear all port statistics
INT agentClearSwitchStats	1.3.6.1.4.1.4526.1.6.1.3.7	INTEGER	read-write	clear all switch statistics
INT agentClearTrapLog	1.3.6.1.4.1.4526.1.6.1.3.8	INTEGER	read-write	clear trap log
INT agentClearVlan	1.3.6.1.4.1.4526.1.6.1.3.9	INTEGER	read-write	clear vlan entries
INT agentResetSystem	1.3.6.1.4.1.4526.1.6.1.3.10	INTEGER	read-write	reset the switch
INT agentSaveConfigStatus	1.3.6.1.4.1.4526.1.6.1.3.11	INTEGER	read-only	Indicates the current status of an save configuration request.
agentCableTesterGroup	1.3.6.1.4.1.4526.1.6.1.4
INT agentCableTesterStatus	1.3.6.1.4.1.4526.1.6.1.4.1	INTEGER	read-write	Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.
U32 agentCableTesterIfIndex	1.3.6.1.4.1.4526.1.6.1.4.2	Unsigned32	read-write	Determines on which port to perform the cable test. Limited to copper based ports.
INT agentCableTesterCableStatus	1.3.6.1.4.1.4526.1.6.1.4.3	INTEGER	read-only	Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.
U32 agentCableTesterMinimumCableLength	1.3.6.1.4.1.4526.1.6.1.4.4	Unsigned32	read-only	The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.
U32 agentCableTesterMaximumCableLength	1.3.6.1.4.1.4526.1.6.1.4.5	Unsigned32	read-only	The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.
U32 agentCableTesterCableFailureLocation	1.3.6.1.4.1.4526.1.6.1.4.6	Unsigned32	read-only	The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if agentCableTesterStatus is not success(2).
gsm7312SwitchingTraps	1.3.6.1.4.1.4526.1.6.1.50
NTF multipleUsersTrap	1.3.6.1.4.1.4526.1.6.1.50.1			trapMgrMultipleUsersLogTrap.
NTF broadcastStormStartTrap	1.3.6.1.4.1.4526.1.6.1.50.2			trapMgrBCastStormStartLogTrap.
NTF broadcastStormEndTrap	1.3.6.1.4.1.4526.1.6.1.50.3			trapMgrBCastStormEndLogTrap.
NTF linkFailureTrap	1.3.6.1.4.1.4526.1.6.1.50.4			trapMgrLinkFailureLogTrap.
NTF vlanRequestFailureTrap	1.3.6.1.4.1.4526.1.6.1.50.5			trapMgrVlanRequestFailureLogTrap
NTF vlanDeleteLastTrap	1.3.6.1.4.1.4526.1.6.1.50.6			trapMgrLastVlanDeleteLastLogTrap
NTF vlanDefaultCfgFailureTrap	1.3.6.1.4.1.4526.1.6.1.50.7			trapMgrDefaultVlanCfgFailureLogTrap
NTF vlanRestoreFailureTrap	1.3.6.1.4.1.4526.1.6.1.50.8			trapMgrVlanRestoreFailureLogTrap
NTF fanFailureTrap	1.3.6.1.4.1.4526.1.6.1.50.9			trapMgrFanFailureLogTrap.
NTF stpInstanceNewRootTrap	1.3.6.1.4.1.4526.1.6.1.50.10			trapMgrStpInstanceNewRootTrap
NTF stpInstanceTopologyChangeTrap	1.3.6.1.4.1.4526.1.6.1.50.11			trapMgrStpInstanceTopologyChange
NTF powerSupplyStatusChangeTrap	1.3.6.1.4.1.4526.1.6.1.50.12			powerSupplyStatusChangeTrap

RFC description

Manages switch inventory, system information, and operational parameters for Netgear GSM7312.

Start monitoring Netgear GSM7312 managed Ethernet switch (L2 switching/cable diagnostics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GSM7312-SWITCHING-MIB