EtherWAN-sw72000

All MIBs › EtherWAN-sw72000

Organization: EtherWAN System Inc.

Last Updated: 2009-02-18

Category: Vendor: EtherWAN

Description: Provides SNMP management for EtherWAN SW72000 series industrial Ethernet switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is EtherWAN-sw72000?

This is a private MIB from EtherWAN for its SW72000 series of industrial/hardened Ethernet switches, used in rugged or environmentally exposed deployments such as rail, transportation, or outdoor infrastructure. It exposes system-level configuration and firmware management data, including firmware revision, hardware revision, product model, MAC address, and gateway IP configuration, plus TFTP-based firmware/config transfer control objects. Its main monitoring value is software/firmware status — reading ewnSystemFirmwareRev and ewnSystemHardwareRev to confirm running versions, watching ewnSystemRebootRequired to know if a pending config change needs a restart, and tracking ewnSystemTFTPState/ewnSystemTFTPAction during remote firmware upgrades. It does not appear to lean on any other IETF MIB, being a fully self-contained vendor tree. It is typically used by field technicians or NMS systems managing fleets of EtherWAN industrial switches for firmware compliance and remote configuration deployment. Network engineers evaluating or troubleshooting this functionality can download the EtherWAN-sw72000 file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in EtherWAN-sw72000. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

EtherWAN SW72000 series industrial Ethernet switch

Monitoring Examples

An operator would read ewnSystemFirmwareRev and ewnSystemHardwareRev to audit the running firmware across a fleet of SW72000 units, then set ewnSystemTFTPIpAddress and ewnSystemTFTPFilename and trigger ewnSystemTFTPAction to push a firmware update, polling ewnSystemTFTPState to confirm success or detect a failed transfer. After a config change, ewnSystemRebootRequired would flip to true, and ewnSystemReboot can be triggered via SNMP to apply it. ewnSystemGatewayIpAddress and ewnSystemMacAddr help confirm the switch's network identity during provisioning.

What Can Be Monitored

firmware revision
hardware revision
product model
TFTP transfer state/action
reboot-required flag
gateway IP address

Imported Objects

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
etherwan	1.3.6.1.4.1.2736
lanSwitch	1.3.6.1.4.1.2736.1			The Switch MIB module for managing EtherWAN Swtich private MIBs
sw72000	1.3.6.1.4.1.2736.1.1
ewnSystem	1.3.6.1.4.1.2736.1.1.1
STR ewnSystemFirmwareRev	1.3.6.1.4.1.2736.1.1.1.1	DisplayString	read-only	Firmware Revision
INT ewnSystemConfigOperation	1.3.6.1.4.1.2736.1.1.1.2	INTEGER	read-write	System Configuration operations. This is a write-only variable. On read, it will always return none(0). On loadDefault(1) write, it will restore to default and reboot the system.
INT ewnSystemReboot	1.3.6.1.4.1.2736.1.1.1.3	INTEGER	read-write	System Warm Reboot Functionality
INT ewnSystemRebootRequired	1.3.6.1.4.1.2736.1.1.1.4	INTEGER	read-only	System Warm Reboot Functionality
ewnSystemTFTP	1.3.6.1.4.1.2736.1.1.1.5
STR ewnSystemTFTPFilename	1.3.6.1.4.1.2736.1.1.1.5.1	DisplayString	read-write	Filename for TFTP download
IP ewnSystemTFTPIpAddress	1.3.6.1.4.1.2736.1.1.1.5.2	IpAddress	read-write	IPAddress of TFTP server
INT ewnSystemTFTPAction	1.3.6.1.4.1.2736.1.1.1.5.3	INTEGER	read-write	Action of the current TFTP session
INT ewnSystemTFTPState	1.3.6.1.4.1.2736.1.1.1.5.4	INTEGER	read-write	State of the current TFTP session
STR ewnSystemProductModel	1.3.6.1.4.1.2736.1.1.1.6	DisplayString	read-only	Product Model Number
STR ewnSystemHardwareRev	1.3.6.1.4.1.2736.1.1.1.7	DisplayString	read-only	Hardware Revision
IP ewnSystemGatewayIpAddress	1.3.6.1.4.1.2736.1.1.1.8	IpAddress	read-write	Default Gateway IP Address for this device
OCT ewnSystemMacAddr	1.3.6.1.4.1.2736.1.1.1.9	OCTET STRING	read-only	MAC Address of the switch.
STR ewnSystemPassword	1.3.6.1.4.1.2736.1.1.1.10	DisplayString	read-write	Login password
STR ewnSystemPasswordEncrypted	1.3.6.1.4.1.2736.1.1.1.11	DisplayString	read-write	Login password with encryption
INT ewnSystemAutoSaveState	1.3.6.1.4.1.2736.1.1.1.12	INTEGER	read-write	Auto save system configuration
INT ewnSystemAutoSaveDelay	1.3.6.1.4.1.2736.1.1.1.13	INTEGER	read-write	Delay time in seconds for auto save system configuration
ewnPort	1.3.6.1.4.1.2736.1.1.2
INT ewnPortCount	1.3.6.1.4.1.2736.1.1.2.1	INTEGER	read-only	Port count
ewnPortTable	1.3.6.1.4.1.2736.1.1.2.2		not-accessible	Port table
ewnPortEntry	1.3.6.1.4.1.2736.1.1.2.2.1		not-accessible	Port entry
INT ewnPortNo	1.3.6.1.4.1.2736.1.1.2.2.1.1	INTEGER	read-only	Port Number
STR ewnPortString	1.3.6.1.4.1.2736.1.1.2.2.1.2	DisplayString	read-only	Port String
INT ewnPortHardwareType	1.3.6.1.4.1.2736.1.1.2.2.1.3	INTEGER	read-only	Port hardware type
INT ewnPortLinkStatus	1.3.6.1.4.1.2736.1.1.2.2.1.4	INTEGER	read-only	Port Link Status
INT ewnPortLinkConfig	1.3.6.1.4.1.2736.1.1.2.2.1.5	INTEGER	read-write	Port Administrative Link Status identical to ifAdminStatus
INT ewnPortSpeedStatus	1.3.6.1.4.1.2736.1.1.2.2.1.6	INTEGER	read-only	Port Speed Status
INT ewnPortSpeedConfig	1.3.6.1.4.1.2736.1.1.2.2.1.7	INTEGER	read-write	Port Speed Configuration
INT ewnPortDupStatus	1.3.6.1.4.1.2736.1.1.2.2.1.8	INTEGER	read-only	Port Duplexity Status
INT ewnPortDupConfig	1.3.6.1.4.1.2736.1.1.2.2.1.9	INTEGER	read-write	Port Duplexity Configuration
INT ewnPortFlowStatus	1.3.6.1.4.1.2736.1.1.2.2.1.10	INTEGER	read-only	Port Flow Control Status
INT ewnPortFlowConfig	1.3.6.1.4.1.2736.1.1.2.2.1.11	INTEGER	read-write	Port Flow Control Configuration
INT ewnPortBroadcastLimit	1.3.6.1.4.1.2736.1.1.2.2.1.13	INTEGER	read-write	Switch Broadcast rate limit type.
INT ewnPortDlfMulticastLimit	1.3.6.1.4.1.2736.1.1.2.2.1.15	INTEGER	read-write	Switch DLF and Multicast rate limit type.
INT ewnPortLimitLevel	1.3.6.1.4.1.2736.1.1.2.2.1.16	INTEGER	read-write	Switch rate limit level.
INT ewnPortPriority	1.3.6.1.4.1.2736.1.1.2.2.1.17	INTEGER	read-write	Default priority for untagged frames received by this port
INT ewnPortSwitchMode	1.3.6.1.4.1.2736.1.1.2.2.1.18	INTEGER	read-write	VLAN switch port mode.
INT ewnPortPVID	1.3.6.1.4.1.2736.1.1.2.2.1.19	INTEGER	read-write	Port VLAN ID (1..4094).
INT ewnPortResetRMONCount	1.3.6.1.4.1.2736.1.1.2.2.1.20	INTEGER	read-write	reset RMON counters on this port.
STR ewnPortAliasName	1.3.6.1.4.1.2736.1.1.2.2.1.21	DisplayString	read-write	Port alias name
ewnMirror	1.3.6.1.4.1.2736.1.1.3
OCT ewnMirrorAvailablePortMap	1.3.6.1.4.1.2736.1.1.3.1	OCTET STRING	read-only	Available mirror port map
INT ewnMirrorCount	1.3.6.1.4.1.2736.1.1.3.2	INTEGER	read-only	Available mirror entry count
ewnMirrorTable	1.3.6.1.4.1.2736.1.1.3.3		not-accessible	Port Mirroring table
ewnMirrorEntry	1.3.6.1.4.1.2736.1.1.3.3.1		not-accessible	Mirror Entry
INT ewnMirrorIndex	1.3.6.1.4.1.2736.1.1.3.3.1.1	INTEGER	read-only	Mirror index
INT ewnMirrorToPort	1.3.6.1.4.1.2736.1.1.3.3.1.2	INTEGER	read-write	Mirror to port
OCT ewnMirrorFromPortMap	1.3.6.1.4.1.2736.1.1.3.3.1.3	OCTET STRING	read-write	Mirror from port map
INT ewnMirrorMode	1.3.6.1.4.1.2736.1.1.3.3.1.4	INTEGER	read-write	Mirror mode
ewnTrunk	1.3.6.1.4.1.2736.1.1.4
INT ewnTrunkCount	1.3.6.1.4.1.2736.1.1.4.1	INTEGER	read-only	Trunk count
ewnTrunkTable	1.3.6.1.4.1.2736.1.1.4.2		not-accessible	Port Trunking table
ewnTrunkEntry	1.3.6.1.4.1.2736.1.1.4.2.1		not-accessible	Trunk Entry
INT ewnTrunkIndex	1.3.6.1.4.1.2736.1.1.4.2.1.1	INTEGER	read-only	Trunk index
OCT ewnTrunkPortMap	1.3.6.1.4.1.2736.1.1.4.2.1.2	OCTET STRING	read-write	Trunk port map
OCT ewnTrunkAvailPortMap	1.3.6.1.4.1.2736.1.1.4.2.1.3	OCTET STRING	read-only	Available trunk port map
INT ewnTrunkMaxNumOfPorts	1.3.6.1.4.1.2736.1.1.4.2.1.4	INTEGER	read-only	Maximum number of ports per trunk group.
ewnLACP	1.3.6.1.4.1.2736.1.1.5
ewnLACP1	1.3.6.1.4.1.2736.1.1.5.1
INT ewnLACPSYSPriority	1.3.6.1.4.1.2736.1.1.5.1.1	INTEGER	read-write	LACP SYSTEM Priority
ewnLACPTable	1.3.6.1.4.1.2736.1.1.5.1.2		not-accessible	LACP table
ewnLACPCONFENTRY	1.3.6.1.4.1.2736.1.1.5.1.2.1		not-accessible	LACP CONF ENTRY
INT ewnLACPPortIndex	1.3.6.1.4.1.2736.1.1.5.1.2.1.1	INTEGER	read-only	LACP Index
STR ewnLACPPortName	1.3.6.1.4.1.2736.1.1.5.1.2.1.2	DisplayString	read-only	LACP Port String
INT ewnLACPTimeout	1.3.6.1.4.1.2736.1.1.5.1.2.1.3	INTEGER	read-write	LACP Port Timeout
INT ewnLACPPriority	1.3.6.1.4.1.2736.1.1.5.1.2.1.4	INTEGER	read-write	LACP Port Priority
ewnLACP2	1.3.6.1.4.1.2736.1.1.5.2
ewnLACPPortTable	1.3.6.1.4.1.2736.1.1.5.2.1		not-accessible	Port LACP table
ewnLACPAGGENTRY	1.3.6.1.4.1.2736.1.1.5.2.1.1		not-accessible	LACP Entry
INT ewnLACPIndex	1.3.6.1.4.1.2736.1.1.5.2.1.1.1	INTEGER	read-only	LACP Index
STR ewnLACPPortString	1.3.6.1.4.1.2736.1.1.5.2.1.1.2	DisplayString	read-only	LACP Port String
INT ewnLACPAdminKey	1.3.6.1.4.1.2736.1.1.5.2.1.1.3	INTEGER	read-write	LACP Admin Key
INT ewnLACPPortMode	1.3.6.1.4.1.2736.1.1.5.2.1.1.4	INTEGER	read-only	LACP Port Mode
ewnBridge	1.3.6.1.4.1.2736.1.1.6
INT ewnBridgeSTPState	1.3.6.1.4.1.2736.1.1.6.1	INTEGER	read-write	Spanning Tree Protocol functionality
INT ewnBridgeAgingTime	1.3.6.1.4.1.2736.1.1.6.2	INTEGER	read-write	Bridge aging time 0 not allowed
ewnIGMP	1.3.6.1.4.1.2736.1.1.7
INT ewnIGMPState	1.3.6.1.4.1.2736.1.1.7.1	INTEGER	read-write	Internet Group Management Protocol functionality
ewnIGMPCfgTable	1.3.6.1.4.1.2736.1.1.7.2		not-accessible	IGMP configuration table, an entry per VLAN
ewnIGMPCfgEntry	1.3.6.1.4.1.2736.1.1.7.2.1		not-accessible	IGMP configuration entry
INT ewnIGMPCfgIndex	1.3.6.1.4.1.2736.1.1.7.2.1.1	INTEGER	read-only	IGMP configuration entry index
INT ewnIGMPCfgVlanID	1.3.6.1.4.1.2736.1.1.7.2.1.2	INTEGER	read-only	IGMP configuration entry's VLAN ID
INT ewnIGMPCfgIGMPVersion	1.3.6.1.4.1.2736.1.1.7.2.1.3	INTEGER	read-write	IGMP Version
INT ewnIGMPCfgFastLeave	1.3.6.1.4.1.2736.1.1.7.2.1.4	INTEGER	read-write	IGMP Fast-leave function
INT ewnIGMPCfgQueryInterval	1.3.6.1.4.1.2736.1.1.7.2.1.5	INTEGER	read-write	IGMP Querrier Interval for active mode
INT ewnIGMPCfgMaxResponseTime	1.3.6.1.4.1.2736.1.1.7.2.1.6	INTEGER	read-write	IGMP Max Response Time for active mode
INT ewnIGMPCfgReportSuppression	1.3.6.1.4.1.2736.1.1.7.2.1.7	INTEGER	read-write	IGMP Report Suppression function
ewnIGMPRecordTable	1.3.6.1.4.1.2736.1.1.7.3		not-accessible	IGMP record database table
ewnIGMPRecordEntry	1.3.6.1.4.1.2736.1.1.7.3.1		not-accessible	IGMP entry
INT ewnIGMPRecordIndex	1.3.6.1.4.1.2736.1.1.7.3.1.1	INTEGER	read-only	IGMP Group index
IP ewnIGMPRecordGroupAddress	1.3.6.1.4.1.2736.1.1.7.3.1.2	IpAddress	read-only	IGMP group address
STR ewnIGMPRecordInterface	1.3.6.1.4.1.2736.1.1.7.3.1.3	DisplayString	read-only	IGMP group member interface
STR ewnIGMPRecordUpTime	1.3.6.1.4.1.2736.1.1.7.3.1.4	DisplayString	read-only	IGMP group up time
STR ewnIGMPRecordExpireTime	1.3.6.1.4.1.2736.1.1.7.3.1.5	DisplayString	read-only	IGMP group expire time
IP ewnIGMPRecordLastReporter	1.3.6.1.4.1.2736.1.1.7.3.1.6	IpAddress	read-only	IGMP group last reporter
ewnVLAN	1.3.6.1.4.1.2736.1.1.8
INT ewnVLANGVRPState	1.3.6.1.4.1.2736.1.1.8.1	INTEGER	read-write	GARP VLAN Registration Protocol functionality
ewnVLANTable	1.3.6.1.4.1.2736.1.1.8.2		not-accessible	VLAN Settings Table
ewnVLANEntry	1.3.6.1.4.1.2736.1.1.8.2.1		not-accessible	VLAN Settings Entry
INT ewnVLANIndex	1.3.6.1.4.1.2736.1.1.8.2.1.1	INTEGER	read-only	VLAN index
INT ewnVLANID	1.3.6.1.4.1.2736.1.1.8.2.1.2	INTEGER	read-write	VLAN ID (valid values 1-4094)
STR ewnVLANName	1.3.6.1.4.1.2736.1.1.8.2.1.3	DisplayString	read-write	VLAN Name. This can only be set during creation of VLAN. It cannot be modified in a later time.
INT ewnVLANState	1.3.6.1.4.1.2736.1.1.8.2.1.4	INTEGER	read-only	The VLAN state.
INT ewnVLANType	1.3.6.1.4.1.2736.1.1.8.2.1.5	INTEGER	read-only	The VLAN type.
OCT ewnVLANStaticPortMap	1.3.6.1.4.1.2736.1.1.8.2.1.6	OCTET STRING	read-write	Ports that always belong to the VLAN.
OCT ewnVLANStaticUntaggedPortMap	1.3.6.1.4.1.2736.1.1.8.2.1.7	OCTET STRING	read-write	Untagged ports of the VLAN.
OCT ewnVLANCurrentPortMap	1.3.6.1.4.1.2736.1.1.8.2.1.8	OCTET STRING	read-only	Ports currently belonging to the VLAN.
OCT ewnVLANCurrentUntaggedPortMap	1.3.6.1.4.1.2736.1.1.8.2.1.9	OCTET STRING	read-only	Untagged ports currently belonging to the VLAN.
OCT ewnVLANCurrentRegisteredPortMap	1.3.6.1.4.1.2736.1.1.8.2.1.10	OCTET STRING	read-only	Registered ports currently belonging to the VLAN.
STR ewnVLANIPAddress	1.3.6.1.4.1.2736.1.1.8.2.1.11	DisplayString	read-write	VLAN IP address / mask
INT ewnVLANAddVlan	1.3.6.1.4.1.2736.1.1.8.3	INTEGER	read-write	Add a new VLAN to ewnVLANTable
INT ewnVLANDeleteVlan	1.3.6.1.4.1.2736.1.1.8.4	INTEGER	read-write	Delete a VLAN from ewnVLANTable
ewnQoS	1.3.6.1.4.1.2736.1.1.9
INT ewnQoSState	1.3.6.1.4.1.2736.1.1.9.1	INTEGER	read-write	QoS state
INT ewnQoSTrust	1.3.6.1.4.1.2736.1.1.9.2	INTEGER	read-write	QoS trust mode
INT ewnQoSPriorityQueueOut	1.3.6.1.4.1.2736.1.1.9.3	INTEGER	read-write	QoS priority queue out mode
ewnQoSWRRqueueTable	1.3.6.1.4.1.2736.1.1.9.4		not-accessible	QoS WRR queue table
ewnQoSWRRqueueEntry	1.3.6.1.4.1.2736.1.1.9.4.1		not-accessible	QoS WRR queue table entry
INT ewnQoSQueueIndex	1.3.6.1.4.1.2736.1.1.9.4.1.1	INTEGER	read-only	QoS Queue Index
INT ewnQoSWRRqueueID	1.3.6.1.4.1.2736.1.1.9.4.1.2	INTEGER	read-only	QoS WRR queue ID
STR ewnQoSWRRqueueCoSmap	1.3.6.1.4.1.2736.1.1.9.4.1.3	DisplayString	read-write	QoS WRR queue CoS mapping
OCT ewnQoSWRRqueueDSCPmap	1.3.6.1.4.1.2736.1.1.9.4.1.4	OCTET STRING	read-write	QoS WRR queue DSCP mapping
INT ewnQoSWRRqueueBandwidth	1.3.6.1.4.1.2736.1.1.9.4.1.5	INTEGER	read-write	QoS WRR queue bandwidth
ewnSNMP	1.3.6.1.4.1.2736.1.1.10
INT ewnSNMPState	1.3.6.1.4.1.2736.1.1.10.1	INTEGER	read-write	SNMP state
STR ewnSNMPCommunitySet	1.3.6.1.4.1.2736.1.1.10.2	DisplayString	read-write	Set community string currently active for this device
STR ewnSNMPCommunityGet	1.3.6.1.4.1.2736.1.1.10.3	DisplayString	read-write	Get community string currently active for this device
STR ewnSNMPTrapCommunity1	1.3.6.1.4.1.2736.1.1.10.4	DisplayString	read-write	Trap community string 1 for this device
STR ewnSNMPTrapCommunity2	1.3.6.1.4.1.2736.1.1.10.5	DisplayString	read-write	Trap community string 2 for this device
STR ewnSNMPTrapCommunity3	1.3.6.1.4.1.2736.1.1.10.6	DisplayString	read-write	Trap community string 3 for this device
STR ewnSNMPTrapCommunity4	1.3.6.1.4.1.2736.1.1.10.7	DisplayString	read-write	Trap community string 4 for this device
STR ewnSNMPTrapCommunity5	1.3.6.1.4.1.2736.1.1.10.8	DisplayString	read-write	Trap community string 5 for this device
IP ewnSNMPTrapIpAddress1	1.3.6.1.4.1.2736.1.1.10.9	IpAddress	read-write	Trap IP Address 1 for this device
IP ewnSNMPTrapIpAddress2	1.3.6.1.4.1.2736.1.1.10.10	IpAddress	read-write	Trap IP Address 2 for this device
IP ewnSNMPTrapIpAddress3	1.3.6.1.4.1.2736.1.1.10.11	IpAddress	read-write	Trap IP Address 3 for this device
IP ewnSNMPTrapIpAddress4	1.3.6.1.4.1.2736.1.1.10.12	IpAddress	read-write	Trap IP Address 4 for this device
IP ewnSNMPTrapIpAddress5	1.3.6.1.4.1.2736.1.1.10.13	IpAddress	read-write	Trap IP Address 5 for this device
INT ewnSNMPTrapLinkDown	1.3.6.1.4.1.2736.1.1.10.16	INTEGER	read-write	Link Down Trap functionality
INT ewnSNMPTrapLinkUp	1.3.6.1.4.1.2736.1.1.10.17	INTEGER	read-write	Link Up Trap functionality
INT ewnSNMPResetNeed	1.3.6.1.4.1.2736.1.1.10.20	INTEGER	read-only	Indicate need to reset SNMP process for SNMP entry changed.
INT ewnSNMPResetSNMP	1.3.6.1.4.1.2736.1.1.10.21	INTEGER	read-write	Reset SNMP process for enable SNMP new setting.
INT ewnSNMPResetRMONCount	1.3.6.1.4.1.2736.1.1.10.22	INTEGER	read-write	Reset RMON counters on all the ports. Please refer to ewnPortEntry group to reset specific port.
ewnSDB	1.3.6.1.4.1.2736.1.1.11
ewnBridgeSDBTable	1.3.6.1.4.1.2736.1.1.11.1		not-accessible	Switching Database table
ewnBridgeSDBEntry	1.3.6.1.4.1.2736.1.1.11.1.1		not-accessible	SDB Entry
INT ewnBridgeSDBIndex	1.3.6.1.4.1.2736.1.1.11.1.1.1	INTEGER	read-only	Switching Database Index
PHY ewnBridgeSDBMacAddress	1.3.6.1.4.1.2736.1.1.11.1.1.2	PhysAddress	read-only	Switching Database MAC address
INT ewnBridgeSDBVlanId	1.3.6.1.4.1.2736.1.1.11.1.1.3	INTEGER	read-only	Switching Database VLAN ID
INT ewnBridgeSDBPortNo	1.3.6.1.4.1.2736.1.1.11.1.1.4	INTEGER	read-only	Switching Database port number
ewnRadius	1.3.6.1.4.1.2736.1.1.12
ewnDHCP	1.3.6.1.4.1.2736.1.1.13
ewnSensor	1.3.6.1.4.1.2736.1.1.14

RFC description

EtherWAN SW72000 managed switch MIB covering ports, trunking, LACP, VLANs, QoS, DHCP, and sensor monitoring.

Start monitoring EtherWAN SW72000 series industrial Ethernet switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download EtherWAN-sw72000

What Is EtherWAN-sw72000?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description