All MIBs › Dell-IpRouter
Organization: Dell
Last Updated: 2004-06-01
Description: Dell-IpRouter module
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Dell-IpRouter?
Dell-IpRouter (documented internally as the RND router MIB) is a Dell-branded private MIB, historically associated with routers derived from RADCOM/RND platforms, that manages RIPv2 routing protocol configuration on router interfaces. It exposes a per-interface RIPv2 configuration table covering the bound address, administrative status, route filtering (inbound/outbound filter type and named filter lists), default-route origination, and authentication key-chain association. This is primarily a routing-protocol configuration MIB rather than a hardware-status one: its monitoring value lies in confirming that RIPv2 is administratively enabled on the correct interfaces and that route filters and default-origination settings match the intended routing policy, since a misconfigured filter or disabled interface would explain missing or unexpected routes. It builds on the standard RIPv2 MIB object model (RFC 1724) with vendor-specific filtering and key-chain extensions (rlRip2IfConf* objects). It is deployed on Dell/RND routers running RIPv2 in small-to-medium enterprise or branch-office IP networks. Engineers can download the Dell-IpRouter file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Dell-IpRouter. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Dell/RND router running RIPv2
Monitoring Examples
An administrator would poll rlRip2IfConfAdminStatus in rsRip2IfConfTable/rsRip2IfConfEntry to confirm RIPv2 is enabled on the expected interfaces, keyed by rsRip2IfConfAddress. rlRip2IfConfInFilteringType/rlRip2IfConfInFilterListName and their outbound counterparts would be checked to verify the correct route filter lists are applied, explaining why certain routes are being suppressed from a neighbor. rlRip2IfConfKeyChain would be checked to confirm RIP authentication is tied to the correct key chain, and rlRip2IfConfDefInfOriginate would show whether the router is configured to originate a default route into RIP.
What Can Be Monitored
- RIPv2 interface administrative status
- inbound/outbound route filter configuration
- default route origination setting
- RIP authentication key chain association
This MIB depends on
Related MIBs
Imported Objects
From Dell-IP
| ipSpec | OBJECT-IDENTITY |
From OSPF-MIB
| AreaID | |
| RouterID | |
| ospfIfEntry | |
| ospfVirtIfEntry |
From RADLAN-IP
| ipRedundancy | OBJECT-IDENTITY |
| ipRipFilter | OBJECT-IDENTITY |
| ipRouteLeaking | OBJECT-IDENTITY |
| rip2Spec | OBJECT-IDENTITY |
| rlIpRoutingProtPreference | OBJECT-IDENTITY |
| rlOspf | OBJECT-IDENTITY |
From RIPv2-MIB
| rip2IfConfEntry | OBJECT-TYPE |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| rsRip2IfConfTable | 1.3.6.1.4.1.89.26.3.1 | not-accessible | This table is extension of rip2IfConfTable (RFC 1724 ,RIP 2) | |
| rsRip2IfConfEntry | 1.3.6.1.4.1.89.26.3.1.1 | not-accessible | The row definition for this table. | |
| IP rsRip2IfConfAddress | 1.3.6.1.4.1.89.26.3.1.1.1 | IpAddress | read-only | The IP Address of this system on the indicated subnet. |
| INT rsRip2IfConfVirtualDis | 1.3.6.1.4.1.89.26.3.1.1.2 | INTEGER | read-write | This variable defines the virtual number of hops assigned to the interface specified by rsIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm. |
| STR rlRip2IfConfKeyChain | 1.3.6.1.4.1.89.26.3.1.1.3 | DisplayString | read-write | Name of the key-chain which rip2 interface uses for md5 authentication |
| INT rlRip2IfConfAdminStatus | 1.3.6.1.4.1.89.26.3.1.1.4 | INTEGER | read-write | This variable defines administrative status of RIP interface. |
| INT rlRip2IfConfInFilteringType | 1.3.6.1.4.1.89.26.3.1.1.5 | INTEGER | read-write | Type of Rx filtering (ACL, Prefix List etc). |
| INT rlRip2IfConfOutFilteringType | 1.3.6.1.4.1.89.26.3.1.1.6 | INTEGER | read-write | Type of Tx filtering (ACL, Prefix List etc). |
| STR rlRip2IfConfInFilterListName | 1.3.6.1.4.1.89.26.3.1.1.7 | DisplayString | read-write | Name of a filtering list. The list defines which networks are to be received and which are to be suppressed in routing updates. List type is defined by rlRip2IfConfFilteringType. |
| STR rlRip2IfConfOutFilterListName | 1.3.6.1.4.1.89.26.3.1.1.8 | DisplayString | read-write | Name of a filtering list. The list defines which networks are to be sent and which are to be suppressed. List type is defined by rlRip2IfConfFilteringType. |
| INT rlRip2IfConfDefInfOriginate | 1.3.6.1.4.1.89.26.3.1.1.9 | INTEGER | read-write | if set to global RIP behavior is specified by the value of rlRip2GlobalDefaultInformationOriginate scalar if set to enabled RIP will advertise default route on this interfaces if set to passiveOnly RIP will advertise default route on this interfaces only if it is configured to passive mode |
| INT rlRip2MibVersion | 1.3.6.1.4.1.89.26.3.2 | INTEGER | read-only | MIB's version, the current version is 2. |
| U32 rlRip2RedistDefaultMetric | 1.3.6.1.4.1.89.26.3.3 | Unsigned32 | read-write | Default metric value when RIP advertises routes, derived by other protocols. |
| T/F rlRip2RedistStaticTransparent | 1.3.6.1.4.1.89.26.3.4 | TruthValue | read-write | If set to TRUE causes RIP to use the routing table metric for redistributed static routes as the RIP metric. If set to FALSE then the metric defined in rlRip2RedistDefaultMetric is used. |
| T/F rlRip2ClearStatistics | 1.3.6.1.4.1.89.26.3.5 | TruthValue | read-write | Clears RIP statistics counters of all interfaces and all peers. |
| T/F rlRip2IfConfGlobalPassiveInterface | 1.3.6.1.4.1.89.26.3.6 | TruthValue | read-write | if set to TRUE all interfaces created will be created as passive (rip2IfConfSend = doNotSend) |
| INT rlRip2GlobalDefInfOriginate | 1.3.6.1.4.1.89.26.3.7 | INTEGER | read-write | if set to Enabled RIP will advertise default route on all RIP interfaces if set to PassiveOnly RIP will advertise default route on all RIP passive interfaces |
| T/F rlRip2RedistConnected | 1.3.6.1.4.1.89.26.3.8 | TruthValue | read-write | If set to TRUE causes RIP to redistribute directly connected interfaces, on which RIP is not enabled. |
| T/F rlRip2RedistConnectedTransparent | 1.3.6.1.4.1.89.26.3.9 | TruthValue | read-write | If set to TRUE causes RIP to use the routing table metric for redistributed connected routes as the RIP metric. If set to FALSE then the metric defined in rlRip2RedistDefaultMetric is used. |
| U32 rlRip2RedistConnectedMetric | 1.3.6.1.4.1.89.26.3.10 | Unsigned32 | read-write | User defined metric value when RIP advertises directly connected interfaces, on which RIP is not enabled. |
| INT ipRedundAdminStatus | 1.3.6.1.4.1.89.26.6.1 | INTEGER | read-write | This parameter controls the IP Redundancy in the device. In case the parameter is Enable and the other router becomes inoperational, all the traffic is handled by this element. |
| INT ipRedundOperStatus | 1.3.6.1.4.1.89.26.6.2 | INTEGER | read-only | obsolete |
| ipRedundRoutersTable | 1.3.6.1.4.1.89.26.6.3 | not-accessible | List of IP addresses backed up by this router. | |
| ipRedundRoutersEntry | 1.3.6.1.4.1.89.26.6.3.1 | not-accessible | The row definition for this table. | |
| IP ipRedundRoutersIfAddr | 1.3.6.1.4.1.89.26.6.3.1.1 | IpAddress | read-only | The Ip address of the IP interface on which the redundancy feature is operational. |
| IP ipRedundRoutersMainRouterAddr | 1.3.6.1.4.1.89.26.6.3.1.2 | IpAddress | read-only | The Ip address of the polled main router. |
| INT ipRedundRoutersOperStatus | 1.3.6.1.4.1.89.26.6.3.1.3 | INTEGER | read-only | If active, the main router is considered inoperational and the IP interface operates as its backup. |
| INT ipRedundRoutersPollInterval | 1.3.6.1.4.1.89.26.6.3.1.4 | INTEGER | read-write | Polling interval for this router (in seconds). If 0 the router is not polled. |
| INT ipRedundRoutersTimeout | 1.3.6.1.4.1.89.26.6.3.1.5 | INTEGER | read-write | Interval in seconds during which the backed-up router must signal. If it does not signal, it is considered inoperational and the IP interface starts operating as backup. |
| INT ipRedundRoutersStatus | 1.3.6.1.4.1.89.26.6.3.1.6 | INTEGER | read-write | Entry status |
| INT ipLeakStaticToRip | 1.3.6.1.4.1.89.26.7.1 | INTEGER | read-write | This parameter controls leaking (redistribution) of static routes to RIP. When enabled, all routes inserted to the IP routing table via SNMP are advertised into RIP. |
| INT ipLeakStaticToOspf | 1.3.6.1.4.1.89.26.7.2 | INTEGER | read-write | This parameter controls leaking (redistribution) of static routes into OSPF. When enabled, all routes inserted to the IP routing table via SNMP are advertised into OSPF as external routes. |
| INT ipLeakOspfToRip | 1.3.6.1.4.1.89.26.7.3 | INTEGER | read-write | This parameter controls leaking (redistribution) of routes from OSPF to RIP. If enabled, all routes learned via OSPF are advertised into RIP. |
| INT ipLeakRipToOspf | 1.3.6.1.4.1.89.26.7.4 | INTEGER | read-write | This parameter controls leaking (redistribution) of routes from RIP to OSPF. If enabled, all routes learned via RIP are advertised into OSPF as external routes. |
| INT ipLeakExtDirectToOspf | 1.3.6.1.4.1.89.26.7.5 | INTEGER | read-write | This parameter controls leaking (redistribution) into OSPF of direct routes external to OSPF, i.e. routes to local network corresponding to IP interfaces on which OSPF is disabled. When enabled, all such direct routes are advertised into OSPF as external routes. |
| rsIpRipFilterGlbTable | 1.3.6.1.4.1.89.26.8.1 | not-accessible | The table of RIP global filters per IP router. | |
| rsIpRipFilterGlbEntry | 1.3.6.1.4.1.89.26.8.1.1 | not-accessible | An entry in the RIP global filter table | |
| INT rsIpRipFilterGlbType | 1.3.6.1.4.1.89.26.8.1.1.1 | INTEGER | read-only | Type of filter - input/output |
| INT rsIpRipFilterGlbNumber | 1.3.6.1.4.1.89.26.8.1.1.2 | INTEGER | read-only | Number of RIP filter. |
| INT rsIpRipFilterGlbStatus | 1.3.6.1.4.1.89.26.8.1.1.3 | INTEGER | read-write | The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table. |
| IP rsIpRipFilterGlbIpAddr | 1.3.6.1.4.1.89.26.8.1.1.4 | IpAddress | read-write | network prefix IP address, as in the forwarding table. |
| INT rsIpRipFilterGlbNetworkMaskBits | 1.3.6.1.4.1.89.26.8.1.1.5 | INTEGER | read-write | the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0 |
| INT rsIpRipFilterGlbMatchBits | 1.3.6.1.4.1.89.26.8.1.1.6 | INTEGER | read-write | the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterGlbNetworkMaskBits must be 0 and is ignored. |
| INT rsIpRipFilterGlbAction | 1.3.6.1.4.1.89.26.8.1.1.7 | INTEGER | read-write | Filter action - permit/deny for this network |
| rsIpRipFilterLclTable | 1.3.6.1.4.1.89.26.8.2 | not-accessible | Table of input/output RIP filters used per IP Interface. | |
| rsIpRipFilterLclEntry | 1.3.6.1.4.1.89.26.8.2.1 | not-accessible | An entry in the Intf RIP filter table | |
| IP rsIpRipFilterLclIpIntf | 1.3.6.1.4.1.89.26.8.2.1.1 | IpAddress | read-only | The IP address identifying the RIP interface for this filter. This value corresponds to rsIpAdEntAddr. |
| INT rsIpRipFilterLclType | 1.3.6.1.4.1.89.26.8.2.1.2 | INTEGER | read-only | Type of filter - input/output |
| INT rsIpRipFilterLclNumber | 1.3.6.1.4.1.89.26.8.2.1.3 | INTEGER | read-only | Number of RIP filter for this Interface |
| INT rsIpRipFilterLclStatus | 1.3.6.1.4.1.89.26.8.2.1.4 | INTEGER | read-write | The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table. |
| IP rsIpRipFilterLclIpAddr | 1.3.6.1.4.1.89.26.8.2.1.5 | IpAddress | read-write | network prefix IP address, as in the forwarding table. |
| INT rsIpRipFilterLclNetworkMaskBits | 1.3.6.1.4.1.89.26.8.2.1.6 | INTEGER | read-write | the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0 |
| INT rsIpRipFilterLclMatchBits | 1.3.6.1.4.1.89.26.8.2.1.7 | INTEGER | read-write | the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterLclNetworkMaskBits must be 0 and is ignored. |
| INT rsIpRipFilterLclAction | 1.3.6.1.4.1.89.26.8.2.1.8 | INTEGER | read-write | Filter action - permit/deny |
| INT rlIpRoutingProtPreferenceDirect | 1.3.6.1.4.1.89.26.13.1 | INTEGER | read-write | The Preference given to routes whose origin is Local IP (i.e. IP interface in IpAddrTable) It is proposed that the value will be higher than dynamic routing protocols. The change of its value may lead to unexpected results, such as routing loops |
| INT rlIpRoutingProtPreferenceStatic | 1.3.6.1.4.1.89.26.13.2 | INTEGER | read-write | The Preference given to routes whose origin is Men configured by Net managment tools, i.e. Command line or SNMP configured. |
| INT rlIpRoutingProtPreferenceOspfInter | 1.3.6.1.4.1.89.26.13.3 | INTEGER | read-write | The Preference given to routes whose origin is internal ospf Links. Relate to routes which are based on OSPF Link State Advertisements of type 1-4 |
| INT rlIpRoutingProtPreferenceOspfExt | 1.3.6.1.4.1.89.26.13.4 | INTEGER | read-write | The Preference given to routes whose origin is external to OSPF i.e. routes imported by as OSPF AS Border router. Relate to routes which are based on OSPF Link State Advertisements of types 5 and 7 |
| INT rlIpRoutingProtPreferenceOspfReject | 1.3.6.1.4.1.89.26.13.5 | INTEGER | read-write | The Preference given to routes whose origin is OSPF and Are inserted to cover gaps in net range |
| INT rlIpRoutingProtPreferenceRipNormal | 1.3.6.1.4.1.89.26.13.6 | INTEGER | read-write | The Preference given to routes whose origin is RIP routing domain |
| INT rlIpRoutingProtPreferenceRipAggregate | 1.3.6.1.4.1.89.26.13.7 | INTEGER | read-write | The Preference given to routes whose origin is aggregation As a method of rip1 to handle the CIDR schema. The idea is that ripv1 aggregates route which fall into certion class of IP. This route is a discard route in effect, and is referenced, at forwarding route look up, if there is no beter match. (which means the route is not available) |
| INT rlIpRoutingProtPreferenceBgp | 1.3.6.1.4.1.89.26.13.8 | INTEGER | read-write | The Preference given to routes whose origin is BGP ROUTERS (EBGP or IBGP) |
| INT rlOspfMibVersion | 1.3.6.1.4.1.89.26.14.1 | INTEGER | read-only | MIB's version, the current version is 1. |
| INT rlOspfAutoInterfaceCreation | 1.3.6.1.4.1.89.26.14.2 | INTEGER | read-only | This variable controls OSPF automatic creation and activation of interfaces. If value is enable - IP interface creation results in creation and activation of OSPF Interface. If value is disable OSPF interface is created but not activated. The option is a platform parameter. |
| rlOspfIfExtTable | 1.3.6.1.4.1.89.26.14.3 | not-accessible | The OSPF Interface Table describes the interfaces from the viewpoint of OSPF. | |
| rlOspfIfExtEntry | 1.3.6.1.4.1.89.26.14.3.1 | not-accessible | The OSPF interface table extension for md5 authentication | |
| STR rlOspfifKeyChain | 1.3.6.1.4.1.89.26.14.3.1.1 | DisplayString | read-write | Name of the key-chain which ospf interface uses for md5 authentication |
| rlOspfRtrLnkTable | 1.3.6.1.4.1.89.26.14.4 | not-accessible | Router Link State Advertisement. | |
| rlOspfRtrLnkEntry | 1.3.6.1.4.1.89.26.14.4.1 | not-accessible | A single entry from Router LSA. | |
| ARE rlOspfRtrLnkAreaId | 1.3.6.1.4.1.89.26.14.4.1.1 | AreaID | read-only | The 32 bit identifier of the Area from which the LSA was received. |
| IP rlOspfRtrLnkLsid | 1.3.6.1.4.1.89.26.14.4.1.2 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU rlOspfRtrLnkRouterId | 1.3.6.1.4.1.89.26.14.4.1.3 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| U32 rlOspfRtrLnkIdx | 1.3.6.1.4.1.89.26.14.4.1.4 | Unsigned32 | read-only | The index is a unsigned 32-bit integer. It is used as sequence number of entry in the LSA and relevant only for Router or Network LSA which can contain unlimited number of entries. |
| I32 rlOspfRtrLnkSequence | 1.3.6.1.4.1.89.26.14.4.1.5 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 rlOspfRtrLnkAge | 1.3.6.1.4.1.89.26.14.4.1.6 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 rlOspfRtrLnkChecksum | 1.3.6.1.4.1.89.26.14.4.1.7 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| U32 rlOspfRtrLnkLength | 1.3.6.1.4.1.89.26.14.4.1.8 | Unsigned32 | read-only | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| INT rlOspfRtrLnkBitV | 1.3.6.1.4.1.89.26.14.4.1.9 | INTEGER | read-only | When set, the router is an endpoint of one or more fully adjacent virtual links having the described area as Transit area (V is for virtual link endpoint). |
| INT rlOspfRtrLnkBitE | 1.3.6.1.4.1.89.26.14.4.1.10 | INTEGER | read-only | When set, the router is an AS boundary router (E is for external). |
| INT rlOspfRtrLnkBitB | 1.3.6.1.4.1.89.26.14.4.1.11 | INTEGER | read-only | When set, the router is an area border router (B is for border). |
| U32 rlOspfRtrLnkLinks | 1.3.6.1.4.1.89.26.14.4.1.12 | Unsigned32 | read-only | The number of router links described in this LSA. This must be the total collection of router links (i.e., interfaces) to the area. |
| IP rlOspfRtrLnkLinkID | 1.3.6.1.4.1.89.26.14.4.1.13 | IpAddress | read-only | Identifies the object that this router link connects to. Value depends on the link's Type. |
| IP rlOspfRtrLnkLinkData | 1.3.6.1.4.1.89.26.14.4.1.14 | IpAddress | read-only | Value depends on the link's Type field. |
| INT rlOspfRtrLnkType | 1.3.6.1.4.1.89.26.14.4.1.15 | INTEGER | read-only | A quick description of the router link. |
| U32 rlOspfRtrLnkMetric | 1.3.6.1.4.1.89.26.14.4.1.16 | Unsigned32 | read-only | The cost of using this router link. |
| rlOspfNetLnkTable | 1.3.6.1.4.1.89.26.14.5 | not-accessible | Network Link State Advertisement. | |
| rlOspfNetLnkEntry | 1.3.6.1.4.1.89.26.14.5.1 | not-accessible | A single entry from Network LSA. | |
| ARE rlOspfNetLnkAreaId | 1.3.6.1.4.1.89.26.14.5.1.1 | AreaID | read-only | The 32 bit identifier of the Area from which the LSA was received. |
| IP rlOspfNetLnkLsid | 1.3.6.1.4.1.89.26.14.5.1.2 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU rlOspfNetLnkRouterId | 1.3.6.1.4.1.89.26.14.5.1.3 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| U32 rlOspfNetLnkIdx | 1.3.6.1.4.1.89.26.14.5.1.4 | Unsigned32 | read-only | The index is a unsigned 32-bit integer. It is used as sequence number of entry in the LSA and relevant only for Router or Network LSA which can contain unlimited number of entries. |
| I32 rlOspfNetLnkSequence | 1.3.6.1.4.1.89.26.14.5.1.5 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 rlOspfNetLnkAge | 1.3.6.1.4.1.89.26.14.5.1.6 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 rlOspfNetLnkChecksum | 1.3.6.1.4.1.89.26.14.5.1.7 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| U32 rlOspfNetLnkLength | 1.3.6.1.4.1.89.26.14.5.1.8 | Unsigned32 | read-only | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| IP rlOspfNetLnkMask | 1.3.6.1.4.1.89.26.14.5.1.9 | IpAddress | read-only | The IP address mask for the network. |
| IP rlOspfNetLnkAttRouter | 1.3.6.1.4.1.89.26.14.5.1.10 | IpAddress | read-only | The Router IDs of each of the routers attached to the network. |
| rlOspfSumLnkTable | 1.3.6.1.4.1.89.26.14.6 | not-accessible | Summary Link State Advertisement for network (Type 3). | |
| rlOspfSumLnkEntry | 1.3.6.1.4.1.89.26.14.6.1 | not-accessible | A single entry from Summary LSA. | |
| ARE rlOspfSumLnkAreaId | 1.3.6.1.4.1.89.26.14.6.1.1 | AreaID | read-only | The 32 bit identifier of the Area from which the LSA was received. |
| IP rlOspfSumLnkLsid | 1.3.6.1.4.1.89.26.14.6.1.2 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU rlOspfSumLnkRouterId | 1.3.6.1.4.1.89.26.14.6.1.3 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 rlOspfSumLnkSequence | 1.3.6.1.4.1.89.26.14.6.1.4 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 rlOspfSumLnkAge | 1.3.6.1.4.1.89.26.14.6.1.5 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 rlOspfSumLnkChecksum | 1.3.6.1.4.1.89.26.14.6.1.6 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| U32 rlOspfSumLnkLength | 1.3.6.1.4.1.89.26.14.6.1.7 | Unsigned32 | read-only | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| IP rlOspfSumLnkMask | 1.3.6.1.4.1.89.26.14.6.1.8 | IpAddress | read-only | Value depends on the link's Type field. |
| U32 rlOspfSumLnkMetric | 1.3.6.1.4.1.89.26.14.6.1.9 | Unsigned32 | read-only | The cost of using this router link. |
| rlOspfAsbLnkTable | 1.3.6.1.4.1.89.26.14.7 | not-accessible | Summary Link State Advertisement for ASBR (Type 4). | |
| rlOspfAsbLnkEntry | 1.3.6.1.4.1.89.26.14.7.1 | not-accessible | A single entry from Summary LSA. | |
| ARE rlOspfAsbLnkAreaId | 1.3.6.1.4.1.89.26.14.7.1.1 | AreaID | read-only | The 32 bit identifier of the Area from which the LSA was received. |
| IP rlOspfAsbLnkLsid | 1.3.6.1.4.1.89.26.14.7.1.2 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU rlOspfAsbLnkRouterId | 1.3.6.1.4.1.89.26.14.7.1.3 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 rlOspfAsbLnkSequence | 1.3.6.1.4.1.89.26.14.7.1.4 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 rlOspfAsbLnkAge | 1.3.6.1.4.1.89.26.14.7.1.5 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 rlOspfAsbLnkChecksum | 1.3.6.1.4.1.89.26.14.7.1.6 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| U32 rlOspfAsbLnkLength | 1.3.6.1.4.1.89.26.14.7.1.7 | Unsigned32 | read-only | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| U32 rlOspfAsbLnkMetric | 1.3.6.1.4.1.89.26.14.7.1.8 | Unsigned32 | read-only | The cost of using this router link. |
| rlOspfAseLnkTable | 1.3.6.1.4.1.89.26.14.8 | not-accessible | External Link State Advertisement. | |
| rlOspfAseLnkEntry | 1.3.6.1.4.1.89.26.14.8.1 | not-accessible | A single entry from External LSA. | |
| IP rlOspfAseLnkLsid | 1.3.6.1.4.1.89.26.14.8.1.1 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU rlOspfAseLnkRouterId | 1.3.6.1.4.1.89.26.14.8.1.2 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 rlOspfAseLnkSequence | 1.3.6.1.4.1.89.26.14.8.1.3 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 rlOspfAseLnkAge | 1.3.6.1.4.1.89.26.14.8.1.4 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 rlOspfAseLnkChecksum | 1.3.6.1.4.1.89.26.14.8.1.5 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| U32 rlOspfAseLnkLength | 1.3.6.1.4.1.89.26.14.8.1.6 | Unsigned32 | read-only | The lenth in bytes of the LSA. This includes the 20 byte LSA header. |
| IP rlOspfAseLnkMask | 1.3.6.1.4.1.89.26.14.8.1.7 | IpAddress | read-only | Value depends on the link's Type field. |
| IP rlOspfAseLnkFrwAddress | 1.3.6.1.4.1.89.26.14.8.1.8 | IpAddress | read-only | Data traffic for the advertised destination will be forwarded to this address. If the Forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the LSA's originator (i.e., the responsible AS boundary router). |
| INT rlOspfAseLnkBitE | 1.3.6.1.4.1.89.26.14.8.1.9 | INTEGER | read-only | The type of external metric. If bit E is set, the metric specified is a Type 2 external metric. |
| U32 rlOspfAseLnkMetric | 1.3.6.1.4.1.89.26.14.8.1.10 | Unsigned32 | read-only | The cost of this route. |
| U32 rlOspfAseLnkTag | 1.3.6.1.4.1.89.26.14.8.1.11 | Unsigned32 | read-only | A 32-bit field attached to each external route. |
| rlospfVirtIfExtTable | 1.3.6.1.4.1.89.26.14.9 | not-accessible | The Virtual Interface Table describes the virtual links that the OSPF Process is configured to carry on. | |
| rlospfVirtIfExtEntry | 1.3.6.1.4.1.89.26.14.9.1 | not-accessible | The OSPF virtual interface table extension for md5 authentication | |
| STR rlospfVirtifKeyChain | 1.3.6.1.4.1.89.26.14.9.1.1 | DisplayString | read-write | Name of the key-chain which ospf virtual interface uses for md5 authentication |
| rlIpRouter | 1.3.6.1.4.1.89.26.18 | The private MIB module definition for RND router MIB. |
RFC description
Configures IP routing, RIP, and OSPF extensions for Dell router systems.
Start monitoring Dell/RND router (RIPv2 routing configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.