All MIBs › DL80-STD-MIB › esIndex
esIndex
Module: DL80-STD-MIB
OID (symbolic): DL80-STD-MIB::esIndex
OID (numeric): 1.3.6.1.4.1.3052.7.2.1.2.1.1
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-only
Description: This number refers to an EventSensor; it has the same meaning as the esIndexES object (see above), except that this object is used only within the esTable branch.
This object's allowable values are 1 through 16, and 200. 200 always refers to the EventSensor inside the unit. 1 through 16 refer to additional attached EventSensors.
The number corresponding to an EventSensor is determined by the user at the initial configuration time. If there is an internal sensor in the unit, it will always be the first item in the Sensor Events setup menu.
For example, if a new EventSensor is configured as the 2nd entry AFTER the internal EventSensor (if one exists) in the Sensor Events Setup Menu, then that EventSensor will be known from then on as EventSensor 2. All point indeces with esIndex=2 will now refer to that particular EventSensor.
What is esIndex?
esIndex identifies an individual EventSensor entry in the esTable, using the same numbering scheme as esIndexES: 200 for the internal EventSensor and 1 through 16 for externally attached ones. Admins use esIndex to walk the esTable and match each EventSensor's name (esName) and factory ID (esID) to the same number referenced in point indices elsewhere in the MIB. For example, esIndex=2 in this table corresponds to the second EventSensor an admin added after the internal one in the Sensor Events Setup Menu.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.3052.7.2.1.2.1.1 snmpwalk -v2c -c public <target> DL80-STD-MIB::esIndex
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.3052.7.2.1.2.1.1.1 snmpget -v2c -c public <target> DL80-STD-MIB::esIndex.1
Start monitoring Asentria EventSensor environmental/facility monitoring device (DL80-series) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the DL80-STD-MIB::esIndex OID value, configure state conditions and alerts, and monitor any Asentria EventSensor environmental/facility monitoring device (DL80-series) from a single console.
OID Breakdown
Upper-level ancestors (7 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.3052 | asentria | ASENTRIA-ROOT-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.3052.7 | dl80 | DL80-STD-MIB |
| 1.3.6.1.4.1.3052.7.2 | config | DL80-STD-MIB |
| 1.3.6.1.4.1.3052.7.2.1 | eventSensorBasics | DL80-STD-MIB |
| 1.3.6.1.4.1.3052.7.2.1.2 | esTable | DL80-STD-MIB |
| 1.3.6.1.4.1.3052.7.2.1.2.1 | esEntry | DL80-STD-MIB |
| 1.3.6.1.4.1.3052.7.2.1.2.1.1 | esIndex | DL80-STD-MIB |