DES3828-SWL3MGMT-MIB

All MIBs › DES3828-SWL3MGMT-MIB

Organization: D-Link Corp.

Last Updated: 2008-05-22

Category: Routing Protocols, Vendor: D-Link

Description: Manages L3 routing and software IP forwarding for D-Link DES-3828 switch.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES3828-SWL3MGMT-MIB?

DES3828-SWL3MGMT-MIB is a D-Link Corp. proprietary enterprise MIB (registered under des3828, imported from SW3800PRIMGMT-MIB) that models Layer 3 routing and software IP-forwarding management for the D-Link DES-3828 switch. It provides global protocol enable/disable switches for RIP, OSPF (including OSPF ECMP), DVMRP, PIM, and VRRP (swL3DevCtrlRIPState, swL3DevCtrlOSPFState, swL3DevCtrlOSPFECMPState, etc.), an IP interface control table (swL3IpCtrlTable) covering address/mask, VLAN binding, addressing mode (manual/BOOTP/DHCP), secondary-address and proxy-ARP flags, and operational state, plus a companion virtual IP interface table for VRRP-style virtual addressing. It also exposes a static route table (swL3IpStaticRouteTable) with primary/backup route state, an IP forwarding-database info table, BOOTP and DNS relay configuration tables (including DHCP Option 82 handling), an MD5 authentication key table used by OSPF/RIP, a route-redistribution table between RIP/OSPF/static/local sources, and OSPF-MIB extension tables for host routes and virtual interfaces reusing standard OSPF-MIB textual conventions. Together these objects let an operator both configure and audit the switch's L3 routing behavior from a single proprietary tree layered on top of the standard OSPF-MIB. It is deployed on D-Link DES-3828 Layer 3 switches, and administrators can download the DES3828-SWL3MGMT-MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES3828-SWL3MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-3828 Layer 3 switches

Monitoring Examples

An operator polls swL3DevCtrlOSPFState and swL3IpCtrlTable's swL3IpCtrlOperState for a routed VLAN interface to confirm OSPF is enabled and the interface is operationally up, then checks swL3RouteRedistriTable to verify static routes are being redistributed into OSPF as expected; an interface reporting down(3) in swL3IpCtrlOperState while swL3DevCtrlOSPFState shows enabled would point to a physical or VLAN-binding problem preventing OSPF from forming adjacencies on that interface.

What Can Be Monitored

RIP/OSPF/DVMRP/PIM/VRRP global enable state
IP interface configuration and operational state
static route table entries and primary/backup state
route redistribution table entries
OSPF/RIP MD5 authentication key table

Imported Objects

From IF-MIB

InterfaceIndex

From OSPF-MIB

AreaID
DesignatedRouterPriority
HelloRange
Metric
PositiveInteger
RouterID
Status
TOSType
UpToMaxAge

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
PhysAddress
RowStatus
TruthValue

From SW3800PRIMGMT-MIB

des3828

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using swL3ospfVirtIfEvents OID:

Select a D-Link DES-3828 switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type swL3ospfVirtIfEvents into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of state changes or error events on this virtual link. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL3MgmtMIB	1.3.6.1.4.1.171.11.69.1.3			The Structure of Layer 3 Network Management Information for the proprietary enterprise.
swL3DevMgmt	1.3.6.1.4.1.171.11.69.1.3.1
swL3DevCtrl	1.3.6.1.4.1.171.11.69.1.3.1.1
INT swL3DevCtrlRIPState	1.3.6.1.4.1.171.11.69.1.3.1.1.1	INTEGER	read-write	This object indicates if the Routing Information Protocol (RIP) version 2 function is enabled or disabled.
INT swL3DevCtrlOSPFState	1.3.6.1.4.1.171.11.69.1.3.1.1.2	INTEGER	read-write	This object indicates if the OSPF protocol is enabled or disabled.
INT swL3DevCtrlDVMRPState	1.3.6.1.4.1.171.11.69.1.3.1.1.3	INTEGER	read-write	This object indicates if the DVMRP protocol is enabled or disabled.
INT swL3DevCtrlPIMState	1.3.6.1.4.1.171.11.69.1.3.1.1.4	INTEGER	read-write	This object indicates if the PIM protocol is enabled or disabled.
INT swL3DevCtrlVRRPState	1.3.6.1.4.1.171.11.69.1.3.1.1.5	INTEGER	read-write	This object indicates if the VRRP protocol is enabled or disabled.
INT swL3DevCtrlOSPFECMPState	1.3.6.1.4.1.171.11.69.1.3.1.1.8	INTEGER	read-write	This object indicates if the ECMP for OSPF protocol is enabled or disabled.
swL3IpMgmt	1.3.6.1.4.1.171.11.69.1.3.2
swL3IpCtrlMgmt	1.3.6.1.4.1.171.11.69.1.3.2.1
swL3IpCtrlTable	1.3.6.1.4.1.171.11.69.1.3.2.1.1		not-accessible	This table contains the IP interface information.
swL3IpCtrlEntry	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1		not-accessible	A list of information about a specific IP interface.
IP swL3IpCtrlIpAddr	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.1	IpAddress	not-accessible	The IP address of the interface. This object can only contain the value of the unicast IP address.
INT swL3IpCtrlIfIndex	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.2	INTEGER	read-only	This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
STR swL3IpCtrlInterfaceName	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.3	DisplayString	read-create	This object indicates the name of the IP interface.
IP swL3IpCtrlIpSubnetMask	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.4	IpAddress	read-create	The IP net mask for this interface.
STR swL3IpCtrlVlanName	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.5	DisplayString	read-create	This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
INT swL3IpCtrlMode	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.6	INTEGER	read-create	This object indicates the IP operation mode. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. manual (2) - The IP address will be set manually. bootp (3) - The IP address will be set automatically from the BOOTP server. dhcp (4) - The IP address will be set automatically from the DHCP server.
T/F swL3IpCtrlSecondary	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.7	TruthValue	read-create	When this is true (1) the IP address is the secondary IP. When false (2), the IP address is the primary IP.
ROW swL3IpCtrlState	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.8	RowStatus	read-create	This variable displays the status of the entry. The status used for creating, modifying, and deleting instances of objects is in this table.
INT swL3IpCtrlOperState	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.9	INTEGER	read-only	The current operational state of the IP interface.
INT swL3IpCtrlProxyARPState	1.3.6.1.4.1.171.11.69.1.3.2.1.1.1.10	INTEGER	read-create	This object indicates if the Proxy ARP function is enabled or disabled.
swL3VirtualIpCtrlTable	1.3.6.1.4.1.171.11.69.1.3.2.1.2		not-accessible	This table contains the virtual IP interface information.
swL3VirtualIpCtrlEntry	1.3.6.1.4.1.171.11.69.1.3.2.1.2.1		not-accessible	A list of information about a specific virtual IP interface.
STR swL3VirtualIpCtrlInterfaceName	1.3.6.1.4.1.171.11.69.1.3.2.1.2.1.1	DisplayString	not-accessible	This object indicates the name of the virtual IP interface.
INT swL3VirtualIpCtrlIfIndex	1.3.6.1.4.1.171.11.69.1.3.2.1.2.1.2	INTEGER	read-only	This object uniquely identifies the virtual IP interface number in the swL3VirtualIpCtrlEntry.
IP swL3VirtualIpCtrlIpAddr	1.3.6.1.4.1.171.11.69.1.3.2.1.2.1.3	IpAddress	read-create	The virtual IP address of the interface. This object can only take the value of the unicast IP address.
IP swL3VirtualIpCtrlIpSubnetMask	1.3.6.1.4.1.171.11.69.1.3.2.1.2.1.4	IpAddress	read-only	The net mask for this interface.
INT swL3VirtualIpCtrlOperState	1.3.6.1.4.1.171.11.69.1.3.2.1.2.1.5	INTEGER	read-only	The current operational state of the virtual IP interface.
ROW swL3VirtualIpCtrlState	1.3.6.1.4.1.171.11.69.1.3.2.1.2.1.9	RowStatus	read-create	This variable displays the status of the entry. The status used for creating, modifying, and deleting instances of the objects in this table.
swL3IpFdbMgmt	1.3.6.1.4.1.171.11.69.1.3.2.2
swL3IpFdbInfoTable	1.3.6.1.4.1.171.11.69.1.3.2.2.1		not-accessible	A table that contains forwarding and/or filtering information. This information is used by the switch to determine how to propagate the received IP packets.
swL3IpFdbInfoEntry	1.3.6.1.4.1.171.11.69.1.3.2.2.1.1		not-accessible	Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
IP swL3IpFdbInfoIpAddr	1.3.6.1.4.1.171.11.69.1.3.2.2.1.1.1	IpAddress	read-only	An IP address for which the switch has forwarding and/or filtering information.
IP swL3IpFdbInfoIpSubnetMask	1.3.6.1.4.1.171.11.69.1.3.2.2.1.1.2	IpAddress	read-only	An IP net mask for this interface for which the switch has forwarding and/or filtering information.
INT swL3IpFdbInfoPort	1.3.6.1.4.1.171.11.69.1.3.2.2.1.1.3	INTEGER	read-only	Either the value '0', or the port number of the packet that has an IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr that has been seen. A value of '0' indicates that the port number has not been learned, but that the switch does have some forwarding/filtering information about this address.
INT swL3IpFdbInfoType	1.3.6.1.4.1.171.11.69.1.3.2.2.1.1.4	INTEGER	read-only	The status of this entry.
INT swL3IpArpAgingTime	1.3.6.1.4.1.171.11.69.1.3.2.4	INTEGER	read-write	The timeout period in minutes for aging out dynamically learned ARP information.
swL3IpStaticRouteTable	1.3.6.1.4.1.171.11.69.1.3.2.5		not-accessible	This entity's IP static routing table.
swL3IpStaticRouteEntry	1.3.6.1.4.1.171.11.69.1.3.2.5.1		not-accessible	A particular route to a particular destination, under a particular policy. Once an entry is built, it shouldn't be modified. That is, it just supports a create or delete action.
IP swL3IpStaticRouteDest	1.3.6.1.4.1.171.11.69.1.3.2.5.1.1	IpAddress	read-only	The destination IP address of this route. This object will not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object with a value of x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
IP swL3IpStaticRouteMask	1.3.6.1.4.1.171.11.69.1.3.2.5.1.2	IpAddress	read-only	Indicates that the mask is to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by referring to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to the value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
INT swL3IpStaticRouteBkupState	1.3.6.1.4.1.171.11.69.1.3.2.5.1.3	INTEGER	read-only	The routing state for this route. The value should be primary (1) or backup (2).
IP swL3IpStaticRouteNextHop	1.3.6.1.4.1.171.11.69.1.3.2.5.1.4	IpAddress	read-create	On remote routes, the address of the next system route; Otherwise, 0.0.0.0.
INT swL3IpStaticRouteMetric	1.3.6.1.4.1.171.11.69.1.3.2.5.1.5	INTEGER	read-create	The routing metric for this route.
INT swL3IpStaticRouteStatus	1.3.6.1.4.1.171.11.69.1.3.2.5.1.6	INTEGER	read-create	This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid (2) �V If this value is written to the object, the corresponding entry will be removed from the table. Valid (3) - This entry will reside in the table.
swL3RelayMgmt	1.3.6.1.4.1.171.11.69.1.3.3
swL3RelayBootpMgmt	1.3.6.1.4.1.171.11.69.1.3.3.1
INT swL3RelayBootpState	1.3.6.1.4.1.171.11.69.1.3.3.1.1	INTEGER	read-write	This object indicates if the BOOTP Relay function is enabled or disabled.
INT swL3RelayBootpHopCount	1.3.6.1.4.1.171.11.69.1.3.3.1.2	INTEGER	read-write	This object indicates the maximum number of router hops that the BOOTP packets can cross.
INT swL3RelayBootpTimeThreshold	1.3.6.1.4.1.171.11.69.1.3.3.1.3	INTEGER	read-write	This object indicates the minimum time in seconds within which the switch must relay the BOOTP request. If this time is exceeded, the switch will drop the BOOTP packet.
INT swL3RelayBootpOption82State	1.3.6.1.4.1.171.11.69.1.3.3.1.4	INTEGER	read-write	This object indicates if the DHCP relay agent information option 82 function is enabled or disabled.
INT swL3RelayBootpOption82Check	1.3.6.1.4.1.171.11.69.1.3.3.1.5	INTEGER	read-write	This object indicates if the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
INT swL3RelayBootpOption82Policy	1.3.6.1.4.1.171.11.69.1.3.3.1.6	INTEGER	read-write	This object indicates the reforwarding policy of DHCP relay agent information option 82. replace (1) - Replace the existing option 82 field in messages. drop (2) - Discard messages with the existing option 82 field. keep (3) - Retain the existing option 82 field in messages.
swL3RelayBootpCtrlTable	1.3.6.1.4.1.171.11.69.1.3.3.1.7		not-accessible	This table specifies the IP address as a destination to forward (relay) BOOTP packets to.
swL3RelayBootpCtrlEntry	1.3.6.1.4.1.171.11.69.1.3.3.1.7.1		not-accessible	A list of information that specifies the IP address of a destination to forward (relay) BOOTP packets to.
STR swL3RelayBootpCtrlInterfaceName	1.3.6.1.4.1.171.11.69.1.3.3.1.7.1.1	DisplayString	read-only	The name of the IP interface.
IP swL3RelayBootpCtrlServer	1.3.6.1.4.1.171.11.69.1.3.3.1.7.1.2	IpAddress	read-only	The BOOTP server IP address.
INT swL3RelayBootpCtrlState	1.3.6.1.4.1.171.11.69.1.3.3.1.7.1.3	INTEGER	read-write	This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid (2) �V If this value is written to the object, the corresponding entry will be removed from the table. valid (3) - This entry will reside in the table.
swL3RelayDnsMgmt	1.3.6.1.4.1.171.11.69.1.3.3.2
INT swL3RelayDnsState	1.3.6.1.4.1.171.11.69.1.3.3.2.1	INTEGER	read-write	This object indicates if the DNS Relay function is enabled or disabled.
IP swL3RelayDnsPrimaryServer	1.3.6.1.4.1.171.11.69.1.3.3.2.2	IpAddress	read-write	This object indicates the address of the primary DNS server.
IP swL3RelayDnsSecondaryServer	1.3.6.1.4.1.171.11.69.1.3.3.2.3	IpAddress	read-write	This object indicates the address of the secondary DNS server.
INT swL3RelayDnsCacheState	1.3.6.1.4.1.171.11.69.1.3.3.2.4	INTEGER	read-write	This object indicates if the DNS Relay cache is enabled or disabled.
INT swL3RelayDnsStaticTableState	1.3.6.1.4.1.171.11.69.1.3.3.2.5	INTEGER	read-write	This object indicates if the DNS Relay static table is enabled or disabled.
swL3RelayDnsCtrlTable	1.3.6.1.4.1.171.11.69.1.3.3.2.6		not-accessible	This table display the current DNS relay static table.
swL3RelayDnsCtrlEntry	1.3.6.1.4.1.171.11.69.1.3.3.2.6.1		not-accessible	A list of information displaying the current DNS relay static table.
STR swL3RelayDnsCtrlDomainName	1.3.6.1.4.1.171.11.69.1.3.3.2.6.1.1	DisplayString	read-only	The domain name of this entry.
IP swL3RelayDnsCtrlIpAddr	1.3.6.1.4.1.171.11.69.1.3.3.2.6.1.2	IpAddress	read-only	The IP address of this entry.
INT swL3RelayDnsCtrlState	1.3.6.1.4.1.171.11.69.1.3.3.2.6.1.3	INTEGER	read-write	This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid (2) �V If this value is written to the object, the corresponding entry will be removed from the table. valid (3) - This entry will reside in the table.
swL3Md5Table	1.3.6.1.4.1.171.11.69.1.3.4		not-accessible	This table display the current MD5 key table.
swL3Md5Entry	1.3.6.1.4.1.171.11.69.1.3.4.1		not-accessible	A list of information displaying the current MD5 key table.
INT swL3Md5KeyId	1.3.6.1.4.1.171.11.69.1.3.4.1.1	INTEGER	read-only	The MD5 key ID.
STR swL3Md5Key	1.3.6.1.4.1.171.11.69.1.3.4.1.2	DisplayString	read-create	An MD5 password of up to 16 bytes.
ROW swL3Md5RowStatus	1.3.6.1.4.1.171.11.69.1.3.4.1.3	RowStatus	read-create	This object indicates the status of this entry.
swL3RouteRedistriTable	1.3.6.1.4.1.171.11.69.1.3.5		not-accessible	Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the various routers routing tables and assigning appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol.
swL3RouteRedistriEntry	1.3.6.1.4.1.171.11.69.1.3.5.1		not-accessible	A list of information displaying the route redistribution table.
INT swL3RouteRedistriSrcProtocol	1.3.6.1.4.1.171.11.69.1.3.5.1.1	INTEGER	read-only	Allows the selection of the protocol for the source device.
INT swL3RouteRedistriDstProtocol	1.3.6.1.4.1.171.11.69.1.3.5.1.2	INTEGER	read-only	Allows the selection of the protocol for the destination device.
INT swL3RouteRedistriType	1.3.6.1.4.1.171.11.69.1.3.5.1.3	INTEGER	read-create	Allows the selection of one of the methods for calculating the metric value.
INT swL3RouteRedistriMetric	1.3.6.1.4.1.171.11.69.1.3.5.1.4	INTEGER	read-create	Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates the default value.
ROW swL3RouteRedistriRowStatus	1.3.6.1.4.1.171.11.69.1.3.5.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL3OspfHostTable	1.3.6.1.4.1.171.11.69.1.3.6		not-accessible	The list of hosts and their metrics that the router will advertise as host routes.
swL3OspfHostEntry	1.3.6.1.4.1.171.11.69.1.3.6.1		not-accessible	A metric to be advertised, for a given type of service, when a given host is reachable.
IP swL3OspfHostIpAddress	1.3.6.1.4.1.171.11.69.1.3.6.1.1	IpAddress	read-only	The IP address of the host.
TOS swL3OspfHostTOS	1.3.6.1.4.1.171.11.69.1.3.6.1.2	TOSType	read-only	The Type of Service for the route being configured.
MET swL3OspfHostMetric	1.3.6.1.4.1.171.11.69.1.3.6.1.3	Metric	read-create	The metric to be advertised.
ARE swL3OspfHostAreaID	1.3.6.1.4.1.171.11.69.1.3.6.1.4	AreaID	read-create	The area of the host entry to be found within. By default, this is the area that a subsuming OSPF interface is in, or 0.0.0.0
ROW swL3OspfHostStatus	1.3.6.1.4.1.171.11.69.1.3.6.1.5	RowStatus	read-create	This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3ospfVirtIfTable	1.3.6.1.4.1.171.11.69.1.3.7		not-accessible	Information about this router's virtual inter- faces.
swL3ospfVirtIfEntry	1.3.6.1.4.1.171.11.69.1.3.7.1		not-accessible	Information about a single virtual interface.
ARE swL3ospfVirtIfAreaId	1.3.6.1.4.1.171.11.69.1.3.7.1.1	AreaID	read-only	The transit area that the virtual link traverses. By definition, this is not 0.0.0.0
ROU swL3ospfVirtIfNeighbor	1.3.6.1.4.1.171.11.69.1.3.7.1.2	RouterID	read-only	The router ID of the virtual neighbor.
UPT swL3ospfVirtIfTransitDelay	1.3.6.1.4.1.171.11.69.1.3.7.1.3	UpToMaxAge	read-create	The estimated number of seconds it takes to transmit a link-state update packet over this interface.
UPT swL3ospfVirtIfRetransInterval	1.3.6.1.4.1.171.11.69.1.3.7.1.4	UpToMaxAge	read-create	The number of seconds between link-state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.
HEL swL3ospfVirtIfHelloInterval	1.3.6.1.4.1.171.11.69.1.3.7.1.5	HelloRange	read-create	The length of time, in seconds, between the hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
NUM swL3ospfVirtIfRtrDeadInterval	1.3.6.1.4.1.171.11.69.1.3.7.1.6	PositiveInteger	read-create	The number of seconds that a router's hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the hello interval. This value must be the same for the virtual neigh- bor.
INT swL3ospfVirtIfState	1.3.6.1.4.1.171.11.69.1.3.7.1.7	INTEGER	read-only	OSPF virtual interface states.
C32 swL3ospfVirtIfEventsEx	1.3.6.1.4.1.171.11.69.1.3.7.1.8	Counter32	read-only	The number of state changes or error events on this virtual link
INT swL3ospfVirtIfAuthType	1.3.6.1.4.1.171.11.69.1.3.7.1.9	INTEGER	read-create	The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.
OCT swL3ospfVirtIfAuthKey	1.3.6.1.4.1.171.11.69.1.3.7.1.10	OCTET STRING	read-create	If authentication type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment.
INT swL3ospfVirtIfAuthKeyID	1.3.6.1.4.1.171.11.69.1.3.7.1.11	INTEGER	read-create	The MD5 key ID.
ROW swL3ospfVirtIfStatus	1.3.6.1.4.1.171.11.69.1.3.7.1.12	RowStatus	read-create	This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3ospfIfTable	1.3.6.1.4.1.171.11.69.1.3.8		not-accessible	The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF.
swL3ospfIfEntry	1.3.6.1.4.1.171.11.69.1.3.8.1		not-accessible	The OSPF interface entry describes one inter- face from the viewpoint of OSPF.
IP swL3ospfIfIpAddress	1.3.6.1.4.1.171.11.69.1.3.8.1.1	IpAddress	read-only	The IP address of this OSPF interface.
I32 swL3ospfAddressLessIf	1.3.6.1.4.1.171.11.69.1.3.8.1.2	Integer32	read-only	For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP addresses and the corresponding value of ifIndex for interfaces having no IP address.
ARE swL3ospfIfAreaId	1.3.6.1.4.1.171.11.69.1.3.8.1.3	AreaID	read-create	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
INT swL3ospfIfType	1.3.6.1.4.1.171.11.69.1.3.8.1.4	INTEGER	read-create	The OSPF interface type. By way of default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma' and links that are definitively point-to-point take the value 'pointToPoint'.
STA swL3ospfIfAdminStat	1.3.6.1.4.1.171.11.69.1.3.8.1.5	Status	read-create	The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some areas. The value 'disabled' denotes that the interface is external to OSPF.
DES swL3ospfIfRtrPriority	1.3.6.1.4.1.171.11.69.1.3.8.1.6	DesignatedRouterPriority	read-create	The priority of this interface. Used in multi-access networks, this field is used by the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their router ID as a tie breaker.
UPT swL3ospfIfTransitDelay	1.3.6.1.4.1.171.11.69.1.3.8.1.7	UpToMaxAge	read-create	The estimated number of seconds it takes to transmit a link state update packet over this interface.
UPT swL3ospfIfRetransInterval	1.3.6.1.4.1.171.11.69.1.3.8.1.8	UpToMaxAge	read-create	The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.
HEL swL3ospfIfHelloInterval	1.3.6.1.4.1.171.11.69.1.3.8.1.9	HelloRange	read-create	The length of time, in seconds, between the hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.
NUM swL3ospfIfRtrDeadInterval	1.3.6.1.4.1.171.11.69.1.3.8.1.10	PositiveInteger	read-create	The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the hello interval. This value must be the same for all routers attached to a common network.
NUM swL3ospfIfPollInterval	1.3.6.1.4.1.171.11.69.1.3.8.1.11	PositiveInteger	read-create	The larger time interval, in seconds, between the hello packets sent to an inactive non- broadcast multi-access neighbor.
INT swL3ospfIfState	1.3.6.1.4.1.171.11.69.1.3.8.1.12	INTEGER	read-only	The OSPF interface state.
IP swL3ospfIfDesignatedRouter	1.3.6.1.4.1.171.11.69.1.3.8.1.13	IpAddress	read-only	The IP address of the designated router.
IP swL3ospfIfBackupDesignatedRouter	1.3.6.1.4.1.171.11.69.1.3.8.1.14	IpAddress	read-only	The IP address of the backup designated router.
C32 swL3ospfIfEvents	1.3.6.1.4.1.171.11.69.1.3.8.1.15	Counter32	read-only	The number of times this OSPF interface has changed its state, or when an error has occurred.
INT swL3ospfIfMulticastForwarding	1.3.6.1.4.1.171.11.69.1.3.8.1.16	INTEGER	read-create	The way multicasts should be forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts. Data link multicasting is not meaning- ful on point-to-point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding.
T/F swL3ospfIfDemand	1.3.6.1.4.1.171.11.69.1.3.8.1.17	TruthValue	read-create	Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.
INT swL3ospfIfAuthType	1.3.6.1.4.1.171.11.69.1.3.8.1.18	INTEGER	read-create	The authentication type specified for an in- terface. Additional authentication types may be assigned locally.
OCT swL3ospfIfAuthKey	1.3.6.1.4.1.171.11.69.1.3.8.1.19	OCTET STRING	read-create	The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey will always return a zero length Octet String.
INT swL3ospfIfAuthKeyID	1.3.6.1.4.1.171.11.69.1.3.8.1.20	INTEGER	read-create	The MD5 key ID.
ROW swL3ospfIfStatus	1.3.6.1.4.1.171.11.69.1.3.8.1.21	RowStatus	read-create	This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3RoutePreference	1.3.6.1.4.1.171.11.69.1.3.9
INT swL3RoutePreferenceRIP	1.3.6.1.4.1.171.11.69.1.3.9.1	INTEGER	read-write	Used to configure the RIP route preference.
INT swL3RoutePreferenceOSPFIntra	1.3.6.1.4.1.171.11.69.1.3.9.2	INTEGER	read-write	Used to configure the OSPF intra route preference.
INT swL3RoutePreferenceStatic	1.3.6.1.4.1.171.11.69.1.3.9.3	INTEGER	read-write	Used to configure the static route preference.
INT swL3RoutePreferenceLocal	1.3.6.1.4.1.171.11.69.1.3.9.4	INTEGER	read-only	Used to read the local route preference.
INT swL3RoutePreferenceOSPFInter	1.3.6.1.4.1.171.11.69.1.3.9.5	INTEGER	read-write	Used to configure the OSPF inter route preference.
INT swL3RoutePreferenceOSPFExtT1	1.3.6.1.4.1.171.11.69.1.3.9.6	INTEGER	read-write	Used to configure the OSPF ExtT1 route preference.
INT swL3RoutePreferenceOSPFExtT2	1.3.6.1.4.1.171.11.69.1.3.9.7	INTEGER	read-write	Used to configure the OSPF ExtT2 route preference.
swL3PimMgmt	1.3.6.1.4.1.171.11.69.1.3.11
swL3PimCbsrInfoMgmt	1.3.6.1.4.1.171.11.69.1.3.11.1
I32 swL3pimCbsrBootStrapPeriod	1.3.6.1.4.1.171.11.69.1.3.11.1.1	Integer32	read-write	At the elected BSR, this is the interval between originating bootstrap messages, and should be equal to 60 seconds.
I32 swL3pimCbsrHashMaskLen	1.3.6.1.4.1.171.11.69.1.3.11.1.2	Integer32	read-write	The length (in bits) of the mask to use in the hash function. For IPv4 we recommend a value of 30. For IPv6 we recommand a value of 126.
swL3pimCbsrTable	1.3.6.1.4.1.171.11.69.1.3.11.1.3		not-accessible	The PIM CBSR Table contains the CBSR related information, like interface and priority.
swL3pimCbsrEntry	1.3.6.1.4.1.171.11.69.1.3.11.1.3.1		not-accessible	An entry in the PIM CBSR Table.
NUM swL3pimCbsrInterface	1.3.6.1.4.1.171.11.69.1.3.11.1.3.1.1	InterfaceIndex	not-accessible	The ifIndex value of this PIM interface.
I32 swL3pimCbsrPriority	1.3.6.1.4.1.171.11.69.1.3.11.1.3.1.2	Integer32	read-write	The preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface.
swL3pimCandidateRPMgmt	1.3.6.1.4.1.171.11.69.1.3.11.2
I32 swL3pimCandidateRPHoldtime	1.3.6.1.4.1.171.11.69.1.3.11.2.1	Integer32	read-write	For C-RPs, this is the holdtime specified in the C-RP-Adv message, and is used by the BSR to time out RPs. This should be set to 2.5 * [C-RP-Adv-Period]. Default: 150 seconds.
I32 swL3pimCandidateRPPriority	1.3.6.1.4.1.171.11.69.1.3.11.2.2	Integer32	read-write	The 'priority' of the included RP, for the corresponding Encoded-Group Address (if any). The highest priority is '0' (i.e. the lower the value of the 'Priority' field, the higher the priority). This field is stored at the BSR upon receipt, along with the RP address and corresponding Encoded-Group Address.
I32 swL3pimCandidateRPWildcardPrefixCnt	1.3.6.1.4.1.171.11.69.1.3.11.2.3	Integer32	read-write	The number of encoded group addresses included in the message; indicating the group prefixes for which the C-RP is advertising. A Prefix-Cnt of '0' implies a prefix of 224.0.0.0 with a mask length of 4; i.e. all multicast groups. If the C-RP is not configured with Group-prefix information, the C-RP puts a default value of '0' in this field.
swL3pimSptMgmt	1.3.6.1.4.1.171.11.69.1.3.11.3
STR swL3pimLastHopSptThreshold	1.3.6.1.4.1.171.11.69.1.3.11.3.1	DisplayString	read-write	Specifies a last hop router threshold.
STR swL3pimRPSptThreshold	1.3.6.1.4.1.171.11.69.1.3.11.3.2	DisplayString	read-write	Specifies an RP threshold.
swL3pimRegChksumIncDataTable	1.3.6.1.4.1.171.11.69.1.3.11.4		not-accessible	The PIM Register Checksum Including Data Table contains the PIM register checksum including data information, like RP address and state.
swL3pimRegChksumIncDataEntry	1.3.6.1.4.1.171.11.69.1.3.11.4.1		not-accessible	An entry in the PIM Register Checksum Including the Data Table.
IP swL3SwL3pimRegChksumIncDataRpAddr	1.3.6.1.4.1.171.11.69.1.3.11.4.1.1	IpAddress	not-accessible	Specifies the RP address.
ROW swL3SwL3pimRegChksumIncDataState	1.3.6.1.4.1.171.11.69.1.3.11.4.1.2	RowStatus	read-create	The state of register checksum including the data for RPs.
swL3PimInfoMgmt	1.3.6.1.4.1.171.11.69.1.3.11.5
I32 swL3pimRegisterProbeTime	1.3.6.1.4.1.171.11.69.1.3.11.5.1	Integer32	read-write	When null registers are used, this is the time between sending a null register and the register-suppression-timer expiring unless it is restarted by receiving a register-stop. Thus, a null register would be sent when the register-suppression-timer reaches this value. Default: 5 seconds.
I32 swL3pimRegisterSuppressionTime	1.3.6.1.4.1.171.11.69.1.3.11.5.2	Integer32	read-write	This is the mean interval between receiving a register-stop and allowing registers to be sent again. A lower value means more frequent register bursts at RP, while a higher value means longer join latency for the new receiver. Default: 60 seconds.
swL3pimInfoTable	1.3.6.1.4.1.171.11.69.1.3.11.5.3		not-accessible	The PIM Information Table contains PIM related information, like DR priority.
swL3pimInfoEntry	1.3.6.1.4.1.171.11.69.1.3.11.5.3.1		not-accessible	An entry in the PIM Information Table.
NUM swL3pimInterface	1.3.6.1.4.1.171.11.69.1.3.11.5.3.1.1	InterfaceIndex	not-accessible	The ifIndex value of this PIM interface.
U32 swL3pimDRPriority	1.3.6.1.4.1.171.11.69.1.3.11.5.3.1.2	Unsigned32	read-write	The DR Priority is a 32-bit unsigned number and the numerically larger priority is always prefered. A router's idea of the current DR on an interface can change when a PIM hello message is received, when a neighbor times out, or when a router's own DR priority changes.
swL3pimStaticRPTable	1.3.6.1.4.1.171.11.69.1.3.11.6		not-accessible	The PIM Static RP Table contains the PIM static RP related information, like group address, group mask, RP address and RP row status.
swL3pimStaticRPEntry	1.3.6.1.4.1.171.11.69.1.3.11.6.1		not-accessible	An entry in the PIM Static RP Table.
IP swL3pimStaticRPGroupAddress	1.3.6.1.4.1.171.11.69.1.3.11.6.1.1	IpAddress	not-accessible	The IP multicast group address which, when combined with swL3pimStaticRPGroupMask, identifies a group prefix for which the local router will advertise itself as a static RP.
IP swL3pimStaticRPGroupMask	1.3.6.1.4.1.171.11.69.1.3.11.6.1.2	IpAddress	not-accessible	The multicast group address mask which, when combined with swL3pimStaticRPGroupAddress, identifies a group prefix for which the local router will advertise itself as a static RP.
IP swL3pimStaticRPAddress	1.3.6.1.4.1.171.11.69.1.3.11.6.1.3	IpAddress	not-accessible	The (unicast) address of the interface which will be advertised as a static RP.
ROW swL3pimStaticRPRowStatus	1.3.6.1.4.1.171.11.69.1.3.11.6.1.4	RowStatus	read-create	The status of this row. New entries may be created or old entries deleted from this table.
swL3pimActiveRPTable	1.3.6.1.4.1.171.11.69.1.3.11.7		not-accessible	The PIM Active RP Table contains the PIM active RP related information, like group address, RP address.
swL3pimActiveRPEntry	1.3.6.1.4.1.171.11.69.1.3.11.7.1		not-accessible	An entry (conceptual row) in the swL3pimActiveRPTable.
IP swL3pimActiveRPGroupAddress	1.3.6.1.4.1.171.11.69.1.3.11.7.1.1	IpAddress	not-accessible	The IP multicast group address for which this entry contains information about the Active-RP.
IP swL3pimActiveRPSourceIPAddress	1.3.6.1.4.1.171.11.69.1.3.11.7.1.2	IpAddress	not-accessible	The IP address for which this entry contains information about the source of multicast data.
IP swL3pimActiveRPSourceIPMask	1.3.6.1.4.1.171.11.69.1.3.11.7.1.3	IpAddress	not-accessible	The IP mask for which this entry contains information about the source of multicast data.
IP swL3pimActiveRPAddress	1.3.6.1.4.1.171.11.69.1.3.11.7.1.4	IpAddress	read-only	The IP address of the Active-RP.
swL3OspfDefaultInfoOriginate	1.3.6.1.4.1.171.11.69.1.3.12
STA swL3OspfDefaultInfoOriginateState	1.3.6.1.4.1.171.11.69.1.3.12.1	Status	read-write	This object indicates if the Default Info Originate is enabled or disabled.
STA swL3OspfDefaultInfoOriginateAlways	1.3.6.1.4.1.171.11.69.1.3.12.2	Status	read-write	This object indicates if the always parameter is enabled or disabled. If 'swL3OspfDefaultInfoOriginateState' is disabled, this object returns to the default setting.
INT swL3OspfDefaultInfoOriginateMettype	1.3.6.1.4.1.171.11.69.1.3.12.3	INTEGER	read-write	This object indicates the type of AS external route. If 'swL3OspfDefaultInfoOriginateState' is disabled, this object returns to the default setting.
INT swL3OspfDefaultInfoOriginateMetric	1.3.6.1.4.1.171.11.69.1.3.12.4	INTEGER	read-write	This object indicates the cost of a default route to be advertised in OSPF. The range is 0 to 16777214.
swL3TraceRouteMgmt	1.3.6.1.4.1.171.11.69.1.3.13
swL3TraceRouteCtrl	1.3.6.1.4.1.171.11.69.1.3.13.1
INT swL3TraceRoutePKTToCPUState	1.3.6.1.4.1.171.11.69.1.3.13.1.1	INTEGER	read-write	This object indicates to control whether to capture IP packet with zero TTL to CPU.

RFC description

Manages Layer 3 routing protocols including OSPF, RIP, DNS relay, and BOOTP on D-Link switches.

Start monitoring D-Link DES-3828 switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES3828-SWL3MGMT-MIB