All MIBs › DES3810-52-L2MGMT-MIB
Organization: D-Link Corp.
Last Updated: 2008-03-10
Category: VLAN and Bridging, Vendor: D-Link
Description: Manages L2 switching, VLANs, and spanning tree for D-Link DES-3810-52 switch.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DES3810-52-L2MGMT-MIB?
DES3810-52-L2MGMT-MIB is a proprietary D-Link enterprise MIB covering Layer 2 network management for the DES-3810-52 switch. It exposes objects for VLAN configuration, spanning tree protocol state, and other core L2 switching functions on the device. Its monitoring value lies in tracking the operational health of the switching layer, for example whether ports are correctly assigned to VLANs and whether STP has converged, which surfaces misconfigurations or topology loops before they cause outages. It follows the general pattern of IEEE 802.1Q VLAN and 802.1D/w STP concepts, implemented as D-Link private enterprise extensions rather than the standard Bridge MIB. It is typically deployed on DES-3810-52 access-layer switches in enterprise or campus wiring closets. Engineers can download the DES3810-52-L2MGMT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DES3810-52-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- D-Link DES-3810-52 switch
- D-Link DES-3810 series L2 switches
Monitoring Examples
An administrator would monitor per-port VLAN assignment tables and spanning-tree port-state objects (following the *Table/*Entry convention typical of this MIB family) to confirm that each access port sits in the correct VLAN and that STP ports have reached the forwarding state. A port unexpectedly stuck in a blocking or listening state would indicate an STP topology change or a cabling loop needing investigation. Since the module description supplied is generic boilerplate and no detailed object list was available for this MIB, this scenario reflects the standard L2 monitoring pattern used across the DES-38xx family rather than a specific named object.
What Can Be Monitored
- VLAN port assignment
- spanning tree port state
- L2 forwarding/switching status
This MIB depends on
Related MIBs
Imported Objects
From DLINK-ID-REC-MIB
| AgentNotifyLevel |
From PORT-SECURITY-MIB
| swPortSecPortIndex | OBJECT-TYPE |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TruthValue |
From SW3810PRIMGMT-MIB
| des3810-52 |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| swL2MgmtMIB | 1.3.6.1.4.1.171.11.114.1.3.2 | The Structure of Layer 2 Network Management Information. | ||
| swL2DevMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.1 | |||
| swL2DevInfo | 1.3.6.1.4.1.171.11.114.1.3.2.1.1 | |||
| INT swDevInfoTotalNumOfPort | 1.3.6.1.4.1.171.11.114.1.3.2.1.1.1 | INTEGER | read-only | The number of ports within this switch. This value is the sum of the ports within this switch. |
| INT swDevInfoNumOfPortInUse | 1.3.6.1.4.1.171.11.114.1.3.2.1.1.2 | INTEGER | read-only | The number of ports in this switch connected to the segment or the end stations. |
| OCT swDevInfoFrontPanelLedStatus | 1.3.6.1.4.1.171.11.114.1.3.2.1.1.4 | OCTET STRING | read-only | This object is a set of system LED indications. The first six octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The sixth LED is Master(Stacking Master Device) LED. For the byte range form 7 to 8, it reflect the MGMT port. Every two bytes are presented to a port. For the byte range from 9 to 104, it reflect the 1~48 FE ports. Every two bytes are presented to a port. For the byte range from 105 to 108, it reflect the 49~50 GE Fiber ports. Every two bytes are presented to a port. For the byte range from 109 to 116, it reflect the 51~52GE Combol ports. Every four bytes are presented to a port. The byte range from 109 to 112, it reflect copper ports. The byte range from 113 to 116, it reflect fiber ports. For the byte range from 65 to 72, it reflect the 27~28GE Combol ports. Every four bytes are presented to a port. The byte range from 65 to 68, it reflect copper ports. The byte range from 69 to 72, it reflect fiber ports. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. Power LED: 01 = fail/error/non existence 02 = work normal Console LED: 01 = Console LED OFF 02 = Console LED ON RPS LED: 01 = RPS LED OFF 02 = RPS LED ON Master LED: 01 = Master LED OFF 02 = Master LED ON Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The remaining bytes are currently unused and must be 0. |
| swL2DevCtrl | 1.3.6.1.4.1.171.11.114.1.3.2.1.2 | |||
| INT swL2DevCtrlSnmpTrapState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.5 | INTEGER | read-write | This object controls the SNMP trap status. |
| INT swL2DevCtrlCleanAllStatisticCounter | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.6 | INTEGER | read-write | When the object is set to active, all statistical counters will be cleared. If set to normal, no action. |
| VLA swL2DevCtrlVlanIdOfFDBTbl | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.7 | VlanId | read-write | Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system. |
| INT swL2MACNotifyState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.8 | INTEGER | read-write | This object can enable or disable MAC Notification. |
| INT swL2MACNotifyHistorySize | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.9 | INTEGER | read-write | This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 . |
| INT swL2MACNotifyInterval | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.10 | INTEGER | read-write | This object indicates the time interval, in seconds, which will trigger MAC notification messages. |
| swL2DevCtrlTelnet | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.14 | |||
| INT swL2DevCtrlTelnetState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.14.1 | INTEGER | read-write | This object controls the Telnet status. |
| INT swL2DevCtrlTelnetTcpPort | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.14.2 | INTEGER | read-write | This object designates TCP ports. When Telnet is disabled, this object is not accessible. |
| VLA swL2DevCtrlManagementVlanId | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.16 | VlanId | read-write | This object controls which previously created VLANs are included in the System IP Interface. |
| swL2DevCtrlWeb | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.17 | |||
| INT swL2DevCtrlWebState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.17.1 | INTEGER | read-write | This object controls the Web status. |
| INT swL2DevCtrlWebTcpPort | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.17.2 | INTEGER | read-write | This object designates TCP ports. When Web is disabled, this object is not accessible. |
| INT swL2DevCtrlLLDPState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.18 | INTEGER | read-write | Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table. |
| INT swL2DevCtrlLLDPForwardMessageState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.19 | INTEGER | read-write | When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded. |
| INT swL2DevCtrlIpAutoconfig | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.20 | INTEGER | read-write | This object controls the IP auto configuration state. |
| swL2DevCtrlCFM | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.21 | |||
| INT swL2DevCtrlCFMState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.21.1 | INTEGER | read-write | This object indicates the CFM global state. |
| swL2DevCtrlCFMPortTable | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.21.2 | not-accessible | A table containing CFM state of speicified ports. | |
| swL2DevCtrlCFMPortEntry | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.21.2.1 | not-accessible | The entry of CFM state on speicified ports. | |
| INT swL2DevCtrlCFMPortIndex | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.21.2.1.1 | INTEGER | not-accessible | This object indicates the port-num. |
| INT swL2DevCtrlCFMPortState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.21.2.1.2 | INTEGER | read-write | This object indicates the CFM state on per-port. |
| INT swL2DevCtrlVLANTrunkState | 1.3.6.1.4.1.171.11.114.1.3.2.1.2.22 | INTEGER | read-write | This indicates the global state of the VLAN trunking feature of the device. |
| swL2DevAlarm | 1.3.6.1.4.1.171.11.114.1.3.2.1.3 | |||
| INT swL2DevAlarmNewRoot | 1.3.6.1.4.1.171.11.114.1.3.2.1.3.1 | INTEGER | read-write | When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap. |
| INT swL2DevAlarmTopologyChange | 1.3.6.1.4.1.171.11.114.1.3.2.1.3.2 | INTEGER | read-write | This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other. |
| INT swL2DevAlarmLinkChange | 1.3.6.1.4.1.171.11.114.1.3.2.1.3.3 | INTEGER | read-write | This object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other. |
| swL2VLANMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.2 | |||
| swL2VlanStaticTable | 1.3.6.1.4.1.171.11.114.1.3.2.2.1 | not-accessible | A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset. | |
| swL2VlanStaticEntry | 1.3.6.1.4.1.171.11.114.1.3.2.2.1.1 | not-accessible | Static information for a VLAN configured into the device by (local or network) management. | |
| VLA swL2VlanIndex | 1.3.6.1.4.1.171.11.114.1.3.2.2.1.1.1 | VlanId | not-accessible | The VLAN-ID or other identifier referring to this VLAN. |
| INT swL2VLANAdvertisement | 1.3.6.1.4.1.171.11.114.1.3.2.2.1.1.2 | INTEGER | read-write | This object indicates if the advertisement is active or not. |
| INT swL2PVIDAutoAssignmentState | 1.3.6.1.4.1.171.11.114.1.3.2.2.2 | INTEGER | read-write | This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned 'default VLAN'. |
| swL2VlanPortInfoTable | 1.3.6.1.4.1.171.11.114.1.3.2.2.3 | not-accessible | A table containing vlan and port role information of each port. | |
| swL2VlanPortInfoEntry | 1.3.6.1.4.1.171.11.114.1.3.2.2.3.1 | not-accessible | The table entry of vlan port information. | |
| INT swL2VlanPortInfoPortIndex | 1.3.6.1.4.1.171.11.114.1.3.2.2.3.1.1 | INTEGER | read-only | The port index. |
| INT swL2VlanPortInfoVid | 1.3.6.1.4.1.171.11.114.1.3.2.2.3.1.2 | INTEGER | read-only | The VLAN-ID assigned to a special port |
| INT swL2VlanPortInfoPortRole | 1.3.6.1.4.1.171.11.114.1.3.2.2.3.1.3 | INTEGER | read-only | The port role of a special port.when none,it means this port is not belong to the vlan. |
| INT swL2NniGvrpBpduAddress | 1.3.6.1.4.1.171.11.114.1.3.2.2.7 | INTEGER | read-write | Specifies the GVRP's BPDU MAC address of NNI port In Q-in_Q status. |
| swL2PortMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.3 | |||
| swL2PortInfoTable | 1.3.6.1.4.1.171.11.114.1.3.2.3.1 | not-accessible | A table that contains information about every port. | |
| swL2PortInfoEntry | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1 | not-accessible | A list of information for each port of the device. | |
| INT swL2PortInfoPortIndex | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1.1 | INTEGER | read-only | This object indicates the module's port number.(1..Max port number in the module) |
| INT swL2PortInfoMediumType | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1.2 | INTEGER | read-only | Indicates medium type of the port number. |
| INT swL2PortInfoUnitID | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1.3 | INTEGER | read-only | Indicates ID of the unit in the system |
| INT swL2PortInfoType | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1.4 | INTEGER | read-only | This object indicates the connector type of this port. |
| INT swL2PortInfoLinkStatus | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1.5 | INTEGER | read-only | This object indicates the port link status. |
| INT swL2PortInfoNwayStatus | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1.6 | INTEGER | read-only | This object indicates the port speed and duplex mode. |
| INT swL2PortInfoErrorDisabled | 1.3.6.1.4.1.171.11.114.1.3.2.3.1.1.8 | INTEGER | read-only | This object indicates the blocking type of this port. |
| swL2PortCtrlTable | 1.3.6.1.4.1.171.11.114.1.3.2.3.2 | not-accessible | A table that contains control information about every port. | |
| swL2PortCtrlEntry | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1 | not-accessible | A list of control information for each port of the device. | |
| INT swL2PortCtrlPortIndex | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.1 | INTEGER | read-only | This object indicates the module's port number.(1..Max port number in the module) |
| INT swL2PortCtrlMediumType | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.2 | INTEGER | read-only | Indicates medium type of the port number. |
| INT swL2PortCtrlUnitIndex | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.3 | INTEGER | read-only | Indicates ID of the unit in the device |
| INT swL2PortCtrlAdminState | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.4 | INTEGER | read-write | This object decides if the port is enabled or disabled. |
| INT swL2PortCtrlNwayState | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.5 | INTEGER | read-write | Chose the port speed, duplex mode, and N-Way function mode. |
| INT swL2PortCtrlFlowCtrlState | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.6 | INTEGER | read-write | The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. |
| INT swL2PortCtrlLearningState | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.7 | INTEGER | read-write | This object decides if the port is locked or not. |
| INT swL2PortCtrlMACNotifyState | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.8 | INTEGER | read-write | This object sets each port's MAC notification state. |
| INT swL2PortCtrlMDIXState | 1.3.6.1.4.1.171.11.114.1.3.2.3.2.1.10 | INTEGER | read-write | This object configures the MDIX setting of the port. |
| INT swL2PortCtrlJumboFrame | 1.3.6.1.4.1.171.11.114.1.3.2.3.3 | INTEGER | read-write | This object configures the switch's jumbo frame settings. |
| INT swL2PortCtrlJumboFrameMaxSize | 1.3.6.1.4.1.171.11.114.1.3.2.3.4 | INTEGER | read-only | This object describes how many bytes the max jumbo frame is. |
| swL2PortCounterCtrlTable | 1.3.6.1.4.1.171.11.114.1.3.2.3.6 | not-accessible | A table that used to clear counter information about every port. | |
| swL2PortCounterCtrlEntry | 1.3.6.1.4.1.171.11.114.1.3.2.3.6.1 | not-accessible | A list of entry used to clear counter information for each port of the device. | |
| INT swL2PortCounterCtrlPortIndex | 1.3.6.1.4.1.171.11.114.1.3.2.3.6.1.1 | INTEGER | read-only | This object indicates the module's port number.(1..Max port number in the module) |
| INT swL2PortCounterClearCtrl | 1.3.6.1.4.1.171.11.114.1.3.2.3.6.1.2 | INTEGER | read-write | This object indicates if to clear the counters for each port of the device or not. |
| swL2PortErrTable | 1.3.6.1.4.1.171.11.114.1.3.2.3.7 | not-accessible | A table that contains error information for each port. | |
| swL2PortErrEntry | 1.3.6.1.4.1.171.11.114.1.3.2.3.7.1 | not-accessible | A list of information regarding port errors on the device. | |
| INT swL2PortErrPortIndex | 1.3.6.1.4.1.171.11.114.1.3.2.3.7.1.1 | INTEGER | read-only | This object indicates the module's port number.(1..Max port number in the module). |
| INT swL2PortErrPortState | 1.3.6.1.4.1.171.11.114.1.3.2.3.7.1.2 | INTEGER | read-only | This object indicates the port state is enabled or disabled. |
| INT swL2PortErrPortConnStatus | 1.3.6.1.4.1.171.11.114.1.3.2.3.7.1.3 | INTEGER | read-only | This object indicates whether the PortStatus is err-disabled or not. |
| INT swL2PortErrPortReason | 1.3.6.1.4.1.171.11.114.1.3.2.3.7.1.4 | INTEGER | read-only | This object describes if the reason for the port error is STP LBD or Storm control. |
| swL2DhcpRelayMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.8 | |||
| swL2TrunkMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.9 | |||
| INT swL2TrunkMaxSupportedEntries | 1.3.6.1.4.1.171.11.114.1.3.2.9.1 | INTEGER | read-only | Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable). |
| INT swL2TrunkCurrentNumEntries | 1.3.6.1.4.1.171.11.114.1.3.2.9.2 | INTEGER | read-only | Current active number of entries in the trunk configuration table. |
| swL2TrunkCtrlTable | 1.3.6.1.4.1.171.11.114.1.3.2.9.3 | not-accessible | This table specifies which ports group a set of ports(up to 8) into a single logical link. | |
| swL2TrunkCtrlEntry | 1.3.6.1.4.1.171.11.114.1.3.2.9.3.1 | not-accessible | A list of information that specifies which ports group a set of ports(up to 8) into a single logical link. | |
| INT swL2TrunkIndex | 1.3.6.1.4.1.171.11.114.1.3.2.9.3.1.1 | INTEGER | read-only | The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module. |
| INT swL2TrunkMasterPort | 1.3.6.1.4.1.171.11.114.1.3.2.9.3.1.3 | INTEGER | read-create | The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on). |
| POR swL2TrunkMember | 1.3.6.1.4.1.171.11.114.1.3.2.9.3.1.4 | PortList | read-create | Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group. |
| INT swL2TrunkFloodingPort | 1.3.6.1.4.1.171.11.114.1.3.2.9.3.1.5 | INTEGER | read-only | The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port. |
| INT swL2TrunkType | 1.3.6.1.4.1.171.11.114.1.3.2.9.3.1.6 | INTEGER | read-create | This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group . |
| ROW swL2TrunkState | 1.3.6.1.4.1.171.11.114.1.3.2.9.3.1.7 | RowStatus | read-create | This object indicates the status of this entry. |
| INT swL2TrunkAlgorithm | 1.3.6.1.4.1.171.11.114.1.3.2.9.4 | INTEGER | read-write | This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. |
| swL2TrunkLACPPortTable | 1.3.6.1.4.1.171.11.114.1.3.2.9.5 | not-accessible | This table specifies which ports group a set of ports(up to 8) into a single logical link. | |
| swL2TrunkLACPPortEntry | 1.3.6.1.4.1.171.11.114.1.3.2.9.5.1 | not-accessible | A list of information specifies which ports group a set of ports(up to 8) into a single logical link. | |
| INT swL2TrunkLACPPortIndex | 1.3.6.1.4.1.171.11.114.1.3.2.9.5.1.1 | INTEGER | read-only | The index of logical port LACP. |
| INT swL2TrunkLACPPortState | 1.3.6.1.4.1.171.11.114.1.3.2.9.5.1.2 | INTEGER | read-write | The state of logical port LACP. |
| swL2TrunkVLANTable | 1.3.6.1.4.1.171.11.114.1.3.2.9.6 | not-accessible | This table is used to manage the VLAN trunking feature of the device. | |
| swL2TrunkVLANEntry | 1.3.6.1.4.1.171.11.114.1.3.2.9.6.1 | not-accessible | This object is used to configure the VLAN trunking settings for each port. | |
| INT swL2TrunkVLANPort | 1.3.6.1.4.1.171.11.114.1.3.2.9.6.1.1 | INTEGER | read-only | This object indicates the port being configured. |
| INT swL2TrunkVLANState | 1.3.6.1.4.1.171.11.114.1.3.2.9.6.1.2 | INTEGER | read-write | The state of the logical port LACP. |
| swL2MirrorMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.10 | |||
| INT swL2MirrorLogicTargetPort | 1.3.6.1.4.1.171.11.114.1.3.2.10.1 | INTEGER | read-write | This object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc. |
| POR swL2MirrorPortSourceIngress | 1.3.6.1.4.1.171.11.114.1.3.2.10.2 | PortList | read-write | This represents the port where ingress packets will be sniffed. |
| POR swL2MirrorPortSourceEgress | 1.3.6.1.4.1.171.11.114.1.3.2.10.3 | PortList | read-write | This represents the port where egress packets will be sniffed. |
| INT swL2MirrorPortState | 1.3.6.1.4.1.171.11.114.1.3.2.10.4 | INTEGER | read-write | This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table. |
| swL2TrafficSegMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.14 | |||
| swL2TrafficSegTable | 1.3.6.1.4.1.171.11.114.1.3.2.14.1 | not-accessible | This table specifies that the port can just forward traffic to the specific port list. | |
| swL2TrafficSegEntry | 1.3.6.1.4.1.171.11.114.1.3.2.14.1.1 | not-accessible | A list of information which specifies the port with its traffic forwarding list. | |
| INT swL2TrafficSegPort | 1.3.6.1.4.1.171.11.114.1.3.2.14.1.1.1 | INTEGER | read-only | The port number of the logical port. |
| POR swL2TrafficSegForwardPorts | 1.3.6.1.4.1.171.11.114.1.3.2.14.1.1.2 | PortList | read-write | The port list to which the specific port can forward traffic. |
| swL2MulticastFilterMode | 1.3.6.1.4.1.171.11.114.1.3.2.17 | |||
| swL2MulticastFilterModeVlanTable | 1.3.6.1.4.1.171.11.114.1.3.2.17.1 | not-accessible | A table that contains information about VLAN multicast filter mode. | |
| swL2MulticastFilterModeVlanEntry | 1.3.6.1.4.1.171.11.114.1.3.2.17.1.1 | not-accessible | A list of multicast filter mode information for each VLAN. | |
| INT swL2MulticastFilterVid | 1.3.6.1.4.1.171.11.114.1.3.2.17.1.1.1 | INTEGER | read-only | Indicates VID for each VLAN. |
| INT swL2MulticastFilterVlanMode | 1.3.6.1.4.1.171.11.114.1.3.2.17.1.1.2 | INTEGER | read-write | Specifies multicast filter mode for each VLAN. |
| swL2DhcpLocalRelayMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.24 | |||
| INT swL2DhcpLocalRelayState | 1.3.6.1.4.1.171.11.114.1.3.2.24.1 | INTEGER | read-write | This object indicates the status of the DHCP local relay function of the switch. |
| swL2DhcpLocalRelayVLANTable | 1.3.6.1.4.1.171.11.114.1.3.2.24.2 | not-accessible | This table is used to manage the DHCP local relay status for each VLAN. | |
| swL2DhcpLocalRelayVLANEntry | 1.3.6.1.4.1.171.11.114.1.3.2.24.2.1 | not-accessible | This object lists the current VLANs in the switch and their corresponding DHCP local relay status. | |
| INT swL2DhcpLocalRelayVLANID | 1.3.6.1.4.1.171.11.114.1.3.2.24.2.1.1 | INTEGER | read-only | This object shows the VIDs of the current VLANS in the switch. |
| INT swL2DhcpLocalRelayVLANState | 1.3.6.1.4.1.171.11.114.1.3.2.24.2.1.2 | INTEGER | read-write | This object indicates the status of the DHCP relay function of the VLAN. |
| swL2MgmtMIBTraps | 1.3.6.1.4.1.171.11.114.1.3.2.100 | |||
| swL2Notify | 1.3.6.1.4.1.171.11.114.1.3.2.100.1 | |||
| swL2NotifyMgmt | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.1 | |||
| swL2NotifyPrefix | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.2 | |||
| swL2NotifFirmware | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.2.0 | |||
| NTF swL2macNotification | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.2.0.1 | This trap indicates the MAC addresses variation in address table . | ||
| NTF swL2PortSecurityViolationTrap | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.2.0.2 | When the port_security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out. | ||
| swl2NotificationBidings | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.2.1 | |||
| OCT swL2macNotifyInfo | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.2.1.1 | OCTET STRING | read-only | This object indicates the last time reboot information. |
| MAC swL2PortSecurityViolationMac | 1.3.6.1.4.1.171.11.114.1.3.2.100.1.2.1.2 | MacAddress | accessible-for-notify | This object indicates the MAC address that violates the port security configuration. |
RFC description
D-Link management MIB for DES-3810-52 Layer 2 managed switch; defines objects for trunk, IGMP, and L2 switching functions.
Start monitoring D-Link DES-3810-52 switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.