All MIBs › CTRON-SSR-L2-MIB › l2FilterInPorts
l2FilterInPorts
Module: CTRON-SSR-L2-MIB
OID (symbolic): CTRON-SSR-L2-MIB::l2FilterInPorts
OID (numeric): 1.3.6.1.4.1.52.2501.1.2.6.1.8
Node type: OBJECT-TYPE
Type: OCTET STRING
Access: read-write
Description: The set of physical ports which allow this source MAC address. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the least significant bit represents the lowest numbered port, and the most significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.) The default value of this object is a string of zeroes of appropriate length. The maximum number of ports/card-module is sysHwModuleNumPorts.
What is l2FilterInPorts?
In the L2 filter table, this is a bitmap of the physical ports this filter rule applies to as inbound ports, with each octet covering eight ports and a set bit meaning the port is included. Admins use it to limit a filter to traffic entering on specific ports rather than the whole switch.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.52.2501.1.2.6.1.8 snmpwalk -v2c -c public <target> CTRON-SSR-L2-MIB::l2FilterInPorts
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.52.2501.1.2.6.1.8.1 snmpget -v2c -c public <target> CTRON-SSR-L2-MIB::l2FilterInPorts.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.52.2501.1.2.6.1.8.1 s <value>
Start monitoring Cabletron/Enterasys Smart Switch Router (SSR) — legacy/deprecated (Layer 2) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CTRON-SSR-L2-MIB::l2FilterInPorts OID value, configure state conditions and alerts, and monitor any Cabletron/Enterasys Smart Switch Router (SSR) — legacy/deprecated (Layer 2) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.52 | cabletron | Cabletron-MIB |
| 1.3.6.1.4.1.52.2501 | ssr | CTRON-SSR-SMI-MIB |
| 1.3.6.1.4.1.52.2501.1 | ssrMibs | CTRON-SSR-SMI-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.52.2501.1.2 | l2Group | CTRON-SSR-L2-MIB |
| 1.3.6.1.4.1.52.2501.1.2.6 | l2FilterTable | CTRON-SSR-L2-MIB |
| 1.3.6.1.4.1.52.2501.1.2.6.1 | l2FilterEntry | CTRON-SSR-L2-MIB |
| 1.3.6.1.4.1.52.2501.1.2.6.1.8 | l2FilterInPorts | CTRON-SSR-L2-MIB |