All MIBs › CISCO-SONET-MIB › csApsArchMode
csApsArchMode
Module: CISCO-SONET-MIB
OID (symbolic): CISCO-SONET-MIB::csApsArchMode
OID (numeric): 1.3.6.1.4.1.9.9.126.1.2.1.1.4
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This object is used to configure APS architecture mode on the working/protection line pairs.
All of the following are supported on single slot. oneToOne(2) is not supported across 2 slots,i.e. the working and protection slot numbers must be the same in oneToOne(2).
onePlusOne : This can be supported on the same card and across 2 cards. This mode means that the transmit and receive signals go only over the active line(which could be working or protection line). (straight cable implied)
oneToOne : This is supported only on the same card This mode means that the transmit and receive signals go over the working and protection lines. (straight cable implied)
anexBOnePlusOne : This can be supported on the same card and across 2 cards. This mode is like the onePlusOne mode, except that the 'csApsDirection' can only be bi-directional. (straight cable implied)
ycableOnePlusOneNok1k2: With Y-cable ignore K1K2 bytes. This mode is the Y-cable redundancy mode.
straightOnePlusOneNok1k2 : With straight cable, ignore K1K2 bytes. This mode is like onePlusOne, but with K1, K2 bytes ignored.
What is csApsArchMode?
Configures the APS architecture mode (e.g., 1+1 or 1:1) used on a working/protection line pair, with some modes restricted to lines on the same slot.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.9.126.1.2.1.1.4 snmpwalk -v2c -c public <target> CISCO-SONET-MIB::csApsArchMode
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.9.126.1.2.1.1.4.1 snmpget -v2c -c public <target> CISCO-SONET-MIB::csApsArchMode.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.9.126.1.2.1.1.4.1 i <value>
Start monitoring Cisco SONET/SDH transport routers with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-SONET-MIB::csApsArchMode OID value, configure state conditions and alerts, and monitor any Cisco SONET/SDH transport routers from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.9 | ciscoMgmt | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.9.126 | ciscoSonetMIB | CISCO-SONET-MIB |
| 1.3.6.1.4.1.9.9.126.1 | ciscoSonetMIBObjects | CISCO-SONET-MIB |
| 1.3.6.1.4.1.9.9.126.1.2 | csApsConfig | CISCO-SONET-MIB |
| 1.3.6.1.4.1.9.9.126.1.2.1 | csApsConfigTable | CISCO-SONET-MIB |
| 1.3.6.1.4.1.9.9.126.1.2.1.1 | csApsConfigEntry | CISCO-SONET-MIB |
| 1.3.6.1.4.1.9.9.126.1.2.1.1.4 | csApsArchMode | CISCO-SONET-MIB |