All MIBs › CISCO-IETF-FRR-MIB › cmplsFrrLogTableMaxEntries
cmplsFrrLogTableMaxEntries
Module: CISCO-IETF-FRR-MIB
OID (symbolic): CISCO-IETF-FRR-MIB::cmplsFrrLogTableMaxEntries
OID (numeric): 1.3.6.1.4.1.9.10.98.1.12
Node type: OBJECT-TYPE
Type: Unsigned32
Access: read-write
Description: Indicates the maximum number of entries allowed in the FRR Log table. Agents receiving SETs for values that cannot be used must return an inconsistent value error. If a manager sets this value to 0, this indicates that no logging should take place by the agent.
If this value is returned as 0, this indicates that no additional log entries will be added to the current table either because the table has been completely filled or logging has been disabled. However, agents may wish to not delete existing entries in the log table so that managers may review them in the future.
It is implied that when mplsFrrLogTableCurrEntries has reached the value of this variable, that logging entries may not continue to be added to the table, although existing ones may remain. Furthermore, an agent may begin to delete existing (perhaps the oldest entries) entries to make room for new ones.
What is cmplsFrrLogTableMaxEntries?
This sets the maximum number of entries allowed in the FRR log table, where a manager setting it to 0 means no logging takes place at all. Setting it too low on a busy PLR with frequent protection events risks losing the log rows needed to diagnose a flapping link once the table fills and starts dropping or overwriting entries, while setting it to 0 turns off log-table population entirely. For example, an admin troubleshooting intermittent facility flaps might raise this from a default of 50 up to 500 entries so a full day's worth of switchover events is retained instead of the oldest ones rolling off or logging being disabled altogether.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.98.1.12 snmpwalk -v2c -c public <target> CISCO-IETF-FRR-MIB::cmplsFrrLogTableMaxEntries
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.98.1.12.1 snmpget -v2c -c public <target> CISCO-IETF-FRR-MIB::cmplsFrrLogTableMaxEntries.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.10.98.1.12.1 i <value>
Start monitoring Cisco MPLS provider-edge/core router with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-IETF-FRR-MIB::cmplsFrrLogTableMaxEntries OID value, configure state conditions and alerts, and monitor any Cisco MPLS provider-edge/core router from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.10 | ciscoExperiment | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.10.98 | cmplsFrrMIB | CISCO-IETF-FRR-MIB |
| 1.3.6.1.4.1.9.10.98.1 | cmplsFrrScalars | CISCO-IETF-FRR-MIB |
| 1.3.6.1.4.1.9.10.98.1.12 | cmplsFrrLogTableMaxEntries | CISCO-IETF-FRR-MIB |