All MIBs › CISCO-FC-ROUTE-MIB › fcRouteVerifyAction
fcRouteVerifyAction
Module: CISCO-FC-ROUTE-MIB
OID (symbolic): CISCO-FC-ROUTE-MIB::fcRouteVerifyAction
OID (numeric): 1.3.6.1.4.1.9.9.284.1.1.3
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: The action to perform a consistency check of fcRouteTable. none (1) - no action verify (2) - perform verify action Writing verify(2) does a consistency check of the fcRouteTable with either one of the following: - with routeTable in the persistent database if the fcRouteVerifyType value is pss(1) - with forwarding information base software tables on the module specified by fcRouteVerifyModule, if the fcRouteVerifyType value is fibShadow(2). - with forwarding information base hardware tables on the module specified by fcRouteVerifyModule if the fcRouteVerifyType value is fibHardware(3). This verify action is performed on the fcRouteTable for the VSAN specified by fcRouteVerifyVsanID and for the route entries of the type specified by fcRouteVerifyRouteType. The result is shown by fcRouteVerifyResult. If a verify, due to a previous action performed, is in progress in the agent, then setting the fcRouteVerifyAction to verify(2) again will fail.
No verification is performed if the value is set to none(1). When read, this object always has the value 'none(1)'.
What is fcRouteVerifyAction?
This read-write control triggers a consistency check of the Fibre Channel route table; setting it to verify(2) initiates validation against another data source, while none(1) means no action is taken.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.9.284.1.1.3 snmpwalk -v2c -c public <target> CISCO-FC-ROUTE-MIB::fcRouteVerifyAction
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.9.284.1.1.3.1 snmpget -v2c -c public <target> CISCO-FC-ROUTE-MIB::fcRouteVerifyAction.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.9.284.1.1.3.1 i <value>
Start monitoring Cisco MDS/Nexus Fibre Channel SAN switches with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-FC-ROUTE-MIB::fcRouteVerifyAction OID value, configure state conditions and alerts, and monitor any Cisco MDS/Nexus Fibre Channel SAN switches from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.9 | ciscoMgmt | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.9.284 | ciscoFcRouteMIB | CISCO-FC-ROUTE-MIB |
| 1.3.6.1.4.1.9.9.284.1 | ciscoFcRouteMIBObjects | CISCO-FC-ROUTE-MIB |
| 1.3.6.1.4.1.9.9.284.1.1 | fcRouteConfig | CISCO-FC-ROUTE-MIB |
| 1.3.6.1.4.1.9.9.284.1.1.3 | fcRouteVerifyAction | CISCO-FC-ROUTE-MIB |